Please help me! I'm desperate
I can't access the data on my harddrive any longer ;-((
The IBM Disk Fitness Test tool tells me:
Model : IBM-DJNA-372200
Microcode level : J71OA30K
ATA Compliance : ATA-4
...
Settings
...
S.M.A.R.T. status : Good
Security feature : Supported
Password : Set
Password level : High
Security mode : Locked
However, I haven't set any password. I don't even know how to set it!!
My system is (was) Linux 2.4.7 with PIIX support and "SCSI over IDE"
enabled,
experimental IDE code disabled.
After booting the system and leaving it one hour alone (idle, no internet
connection)
I wanted to start XWindows (4.01). However, it switched the video mode and
suddenly
locked up for ~10 sec. I pressed Ctrl-Alt-Backspace/Del several times to
reboot.
After some seconds it responded and seemed to shut down as usual.
Since then the hd is locked and I don't know why.
According to the ATA-3 specification there are two passwords: a master and
a user password.
The passwords are stored in the EPROM of the hd and are certainly very very
hard to remove.
A locked drive rejects all media access commands.
When a new master password is set, the drive won't be locked.
Setting a new user password locks the drive the next time it is powered-on.
A drive can be unlocked by one of the two passwords.
IBM sets the master password to all ASCII blanks (0x20) during
manufacturing.
To unlock a drive one has to send the command SECURITY UNLOCK (0xBB)
and transfer a single sector to the drive:
Word
0 Bit 0 Identifier: 0=compare user password, 0=compare master password
1-16 Password (32 Bytes)
17-255 reserved
Word 128 of the Identify Drive command contains the Security status:
Bit
8 : Security level 0=High (can be unlocked), 1=Maximum (disk must be
erased)
4 : 1=Security count expired (more than five failed unlock tries,
hard-reset necessary)
3 : 1=Security frozen (all security commands aborted)
2 : 1=Security locked (media access not allowed)
1 : 1=Security enabled
0 : 1=Security supported
Something must have sent a lock command to my hd. Maybe a bug in the IDE
code?
I hope to be able to unlock my drive using the default master password.
My question is: how can I send the unlock command to the hd?
Is there any program that can do it?
AFAICS one can send only the command code using a HDIO_DRIVE_CMD ioctl.
But how can I transfer the password?
Any ideas?
Thank you very much in advance!
PS: please CC to me
Thomas Tanner-------------------
tanner@(ffii.org|gnu.org|gmx.de)
On Tue, Jul 31, 2001 at 01:00:07PM +0200, Thomas Tanner wrote:
> I can't access the data on my harddrive any longer ;-((
>
> The IBM Disk Fitness Test tool tells me:
> Model : IBM-DJNA-372200
> Microcode level : J71OA30K
> ATA Compliance : ATA-4
> Security feature : Supported
> Password : Set
> Password level : High
> Security mode : Locked
>
> However, I haven't set any password. I don't even know how to set it!!
> My system is (was) Linux 2.4.7 with PIIX support and "SCSI over IDE"
> enabled,
> I wanted to start XWindows (4.01). However, it switched the video mode and
> suddenly locked up for ~10 sec. I pressed Ctrl-Alt-Backspace/Del
> After some seconds it responded and seemed to shut down as usual.
> Since then the hd is locked and I don't know why.
Better shield your monitor?
> According to the ATA-3 specification
ATA-4 is also online.
> To unlock a drive one has to send the command SECURITY UNLOCK (0xBB)
> and transfer a single sector to the drive:
Maybe someone has already done it. Otherwise you'll have to play a little
with the code. It is easy. You could try to take setmax and hdparm as example
and add an ioctl that combines HDIO_DRIVE_TASK and HDIO_DRIVE_CMD.