Adding Aspeed AST2400 and AST2600 binding for edac driver.
Signed-off-by: Troy Lee <[email protected]>
---
.../devicetree/bindings/edac/aspeed-sdram-edac.txt | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
index 6a0f3d90d682..8ca9e0a049d8 100644
--- a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
+++ b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
@@ -1,6 +1,6 @@
-Aspeed AST2500 SoC EDAC node
+Aspeed BMC SoC EDAC node
-The Aspeed AST2500 SoC supports DDR3 and DDR4 memory with and without ECC (error
+The Aspeed BMC SoC supports DDR3 and DDR4 memory with and without ECC (error
correction check).
The memory controller supports SECDED (single bit error correction, double bit
@@ -11,7 +11,10 @@ Note, the bootloader must configure ECC mode in the memory controller.
Required properties:
-- compatible: should be "aspeed,ast2500-sdram-edac"
+- compatible: should be one of
+ - "aspeed,ast2400-sdram-edac"
+ - "aspeed,ast2500-sdram-edac"
+ - "aspeed,ast2600-sdram-edac"
- reg: sdram controller register set should be <0x1e6e0000 0x174>
- interrupts: should be AVIC interrupt #0
--
2.17.1
Adding AST2400 and AST2600 edac driver support.
Signed-off-by: Troy Lee <[email protected]>
---
drivers/edac/Kconfig | 6 +-
drivers/edac/aspeed_edac.c | 114 +++++++++++++++++++++++++++++--------
2 files changed, 94 insertions(+), 26 deletions(-)
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index fc30f2ef9782..8ea70746d0bf 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -508,10 +508,10 @@ config EDAC_QCOM
health, you should probably say 'Y' here.
config EDAC_ASPEED
- tristate "Aspeed AST 2500 SoC"
- depends on MACH_ASPEED_G5
+ tristate "Aspeed AST BMC SoC"
+ depends on (MACH_ASPEED_G4 || MACH_ASPEED_G5 || MACH_ASPEED_G6)
help
- Support for error detection and correction on the Aspeed AST 2500 SoC.
+ Support for error detection and correction on the Aspeed AST BMC SoC.
First, ECC must be configured in the bootloader. Then, this driver
will expose error counters via the EDAC kernel framework.
diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
index fbec28dc661d..03a3c12f6bf6 100644
--- a/drivers/edac/aspeed_edac.c
+++ b/drivers/edac/aspeed_edac.c
@@ -14,12 +14,11 @@
#include <linux/regmap.h>
#include "edac_module.h"
-
#define DRV_NAME "aspeed-edac"
-
#define ASPEED_MCR_PROT 0x00 /* protection key register */
#define ASPEED_MCR_CONF 0x04 /* configuration register */
+#define ASPEED_MCR_REQ 0x08 /* Graphics Memory Protection register */
#define ASPEED_MCR_INTR_CTRL 0x50 /* interrupt control/status register */
#define ASPEED_MCR_ADDR_UNREC 0x58 /* address of first un-recoverable error */
#define ASPEED_MCR_ADDR_REC 0x5c /* address of last recoverable error */
@@ -34,10 +33,8 @@
#define ASPEED_MCR_INTR_CTRL_CNT_UNREC GENMASK(15, 12)
#define ASPEED_MCR_INTR_CTRL_ENABLE (BIT(0) | BIT(1))
-
static struct regmap *aspeed_regmap;
-
static int regmap_reg_write(void *context, unsigned int reg, unsigned int val)
{
void __iomem *regs = (void __iomem *)context;
@@ -53,7 +50,6 @@ static int regmap_reg_write(void *context, unsigned int reg, unsigned int val)
return 0;
}
-
static int regmap_reg_read(void *context, unsigned int reg, unsigned int *val)
{
void __iomem *regs = (void __iomem *)context;
@@ -63,6 +59,76 @@ static int regmap_reg_read(void *context, unsigned int reg, unsigned int *val)
return 0;
}
+extern void aspeed_sdmc_disable_mem_protection(u8 req)
+{
+ u32 req_val = 0;
+
+ regmap_read(aspeed_regmap, ASPEED_MCR_REQ, &req_val);
+
+ req_val &= ~BIT(req);
+
+ regmap_write(aspeed_regmap, ASPEED_MCR_REQ, req_val);
+}
+EXPORT_SYMBOL(aspeed_sdmc_disable_mem_protection);
+
+static const u32 ast2400_dram_table[] = {
+ 0x04000000, //64MB
+ 0x08000000, //128MB
+ 0x10000000, //256MB
+ 0x20000000, //512MB
+};
+
+static const u32 ast2500_dram_table[] = {
+ 0x08000000, //128MB
+ 0x10000000, //256MB
+ 0x20000000, //512MB
+ 0x40000000, //1024MB
+};
+
+static const u32 ast2600_dram_table[] = {
+ 0x10000000, //256MB
+ 0x20000000, //512MB
+ 0x40000000, //1024MB
+ 0x80000000, //2048MB
+};
+
+extern u32 aspeed_get_dram_size(void)
+{
+ u32 reg04;
+ u32 size;
+
+ regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
+
+#if defined(CONFIG_MACH_ASPEED_G6)
+ size = ast2600_dram_table[reg04 & 0x3];
+#elif defined(CONFIG_MACH_ASPEED_G5)
+ size = ast2500_dram_table[reg04 & 0x3];
+#else
+ size = ast2400_dram_table[reg04 & 0x3];
+#endif
+ return size;
+}
+EXPORT_SYMBOL(aspeed_get_dram_size);
+
+static const u32 aspeed_vga_table[] = {
+ 0x800000, //8MB
+ 0x1000000, //16MB
+ 0x2000000, //32MB
+ 0x4000000, //64MB
+};
+
+extern u32 aspeed_get_vga_size(void)
+{
+ u32 reg04;
+ u32 size;
+
+ regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
+
+ size = aspeed_vga_table[((reg04 & 0xC) >> 2)];
+ return size;
+}
+EXPORT_SYMBOL(aspeed_get_vga_size);
+
static bool regmap_is_volatile(struct device *dev, unsigned int reg)
{
switch (reg) {
@@ -209,8 +275,8 @@ static int config_irq(void *ctx, struct platform_device *pdev)
/* register interrupt handler */
irq = platform_get_irq(pdev, 0);
dev_dbg(&pdev->dev, "got irq %d\n", irq);
- if (irq < 0)
- return irq;
+ if (!irq)
+ return -ENODEV;
rc = devm_request_irq(&pdev->dev, irq, mcr_isr, IRQF_TRIGGER_HIGH,
DRV_NAME, ctx);
@@ -239,7 +305,11 @@ static int init_csrows(struct mem_ctl_info *mci)
int rc;
/* retrieve info about physical memory from device tree */
- np = of_find_node_by_path("/memory");
+#ifdef CONFIG_MACH_ASPEED_G4
+ np = of_find_node_by_path("/memory@40000000");
+#else
+ np = of_find_node_by_path("/memory@80000000");
+#endif
if (!np) {
dev_err(mci->pdev, "dt: missing /memory node\n");
return -ENODEV;
@@ -281,11 +351,19 @@ static int aspeed_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct edac_mc_layer layers[2];
struct mem_ctl_info *mci;
+ struct device_node *np;
+ struct resource *res;
void __iomem *regs;
- u32 reg04;
int rc;
- regs = devm_platform_ioremap_resource(pdev, 0);
+ /* setup regmap */
+ np = dev->of_node;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENOENT;
+
+ regs = devm_ioremap_resource(dev, res);
if (IS_ERR(regs))
return PTR_ERR(regs);
@@ -294,13 +372,6 @@ static int aspeed_probe(struct platform_device *pdev)
if (IS_ERR(aspeed_regmap))
return PTR_ERR(aspeed_regmap);
- /* bail out if ECC mode is not configured */
- regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
- if (!(reg04 & ASPEED_MCR_CONF_ECC)) {
- dev_err(&pdev->dev, "ECC mode is not configured in u-boot\n");
- return -EPERM;
- }
-
edac_op_state = EDAC_OPSTATE_INT;
/* allocate & init EDAC MC data structure */
@@ -373,13 +444,13 @@ static int aspeed_remove(struct platform_device *pdev)
return 0;
}
-
static const struct of_device_id aspeed_of_match[] = {
+ { .compatible = "aspeed,ast2400-sdram-edac" },
{ .compatible = "aspeed,ast2500-sdram-edac" },
+ { .compatible = "aspeed,ast2600-sdram-edac" },
{},
};
-
static struct platform_driver aspeed_driver = {
.driver = {
.name = DRV_NAME,
@@ -395,18 +466,15 @@ static int __init aspeed_init(void)
return platform_driver_register(&aspeed_driver);
}
-
static void __exit aspeed_exit(void)
{
platform_driver_unregister(&aspeed_driver);
}
-
module_init(aspeed_init);
module_exit(aspeed_exit);
-
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
-MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
+MODULE_DESCRIPTION("Aspeed EDAC driver");
MODULE_VERSION("1.0");
--
2.17.1
Adding Aspeed AST2600 edac node into common devicetree.
Signed-off-by: Troy Lee <[email protected]>
---
arch/arm/boot/dts/aspeed-g6.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index 97ca743363d7..fb144515f397 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -69,6 +69,12 @@
always-on;
};
+ edac: sdram@1e6e0000 {
+ compatible = "aspeed,ast2600-sdram-edac", "syscon";
+ reg = <0x1e6e0000 0x174>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
ahb {
compatible = "simple-bus";
#address-cells = <1>;
--
2.17.1
Hello Troy,
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <[email protected]>
> ---
> drivers/edac/Kconfig | 6 +-
> drivers/edac/aspeed_edac.c | 114 +++++++++++++++++++++++++++++--------
> 2 files changed, 94 insertions(+), 26 deletions(-)
Uh, there are quite some non-trivial changes. I'll have a look over the coming weekend.
Testing an edac driver comes with challenges. Did you test your code? If so, how?
That's how I was testing my original edac 2500 driver http://students.engr.scu.edu/~sschaeck/misc/aspeed-edac.html
Stefan
Hi Troy,
I like the idea of expanding the driver's support to cover the other SoC
generations, but not at the cost of making the build of the driver
SoC-specific. I've made some comments below in this regard.
On Mon, 30 Nov 2020, at 19:03, Troy Lee wrote:
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <[email protected]>
> ---
> drivers/edac/Kconfig | 6 +-
> drivers/edac/aspeed_edac.c | 114 +++++++++++++++++++++++++++++--------
> 2 files changed, 94 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
> index fc30f2ef9782..8ea70746d0bf 100644
> --- a/drivers/edac/Kconfig
> +++ b/drivers/edac/Kconfig
> @@ -508,10 +508,10 @@ config EDAC_QCOM
> health, you should probably say 'Y' here.
>
> config EDAC_ASPEED
> - tristate "Aspeed AST 2500 SoC"
> - depends on MACH_ASPEED_G5
> + tristate "Aspeed AST BMC SoC"
> + depends on (MACH_ASPEED_G4 || MACH_ASPEED_G5 || MACH_ASPEED_G6)
> help
> - Support for error detection and correction on the Aspeed AST 2500 SoC.
> + Support for error detection and correction on the Aspeed AST BMC SoC.
>
> First, ECC must be configured in the bootloader. Then, this driver
> will expose error counters via the EDAC kernel framework.
> diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
> index fbec28dc661d..03a3c12f6bf6 100644
> --- a/drivers/edac/aspeed_edac.c
> +++ b/drivers/edac/aspeed_edac.c
> @@ -14,12 +14,11 @@
> #include <linux/regmap.h>
> #include "edac_module.h"
>
> -
> #define DRV_NAME "aspeed-edac"
>
> -
> #define ASPEED_MCR_PROT 0x00 /* protection key register */
> #define ASPEED_MCR_CONF 0x04 /* configuration register */
> +#define ASPEED_MCR_REQ 0x08 /* Graphics Memory Protection register */
> #define ASPEED_MCR_INTR_CTRL 0x50 /* interrupt control/status register */
> #define ASPEED_MCR_ADDR_UNREC 0x58 /* address of first un-recoverable error */
> #define ASPEED_MCR_ADDR_REC 0x5c /* address of last recoverable error */
> @@ -34,10 +33,8 @@
> #define ASPEED_MCR_INTR_CTRL_CNT_UNREC GENMASK(15, 12)
> #define ASPEED_MCR_INTR_CTRL_ENABLE (BIT(0) | BIT(1))
>
> -
> static struct regmap *aspeed_regmap;
>
> -
> static int regmap_reg_write(void *context, unsigned int reg, unsigned
> int val)
> {
> void __iomem *regs = (void __iomem *)context;
> @@ -53,7 +50,6 @@ static int regmap_reg_write(void *context, unsigned
> int reg, unsigned int val)
> return 0;
> }
>
> -
> static int regmap_reg_read(void *context, unsigned int reg, unsigned
> int *val)
> {
> void __iomem *regs = (void __iomem *)context;
> @@ -63,6 +59,76 @@ static int regmap_reg_read(void *context, unsigned
> int reg, unsigned int *val)
> return 0;
> }
>
> +extern void aspeed_sdmc_disable_mem_protection(u8 req)
> +{
> + u32 req_val = 0;
> +
> + regmap_read(aspeed_regmap, ASPEED_MCR_REQ, &req_val);
> +
> + req_val &= ~BIT(req);
> +
> + regmap_write(aspeed_regmap, ASPEED_MCR_REQ, req_val);
> +}
> +EXPORT_SYMBOL(aspeed_sdmc_disable_mem_protection);
> +
> +static const u32 ast2400_dram_table[] = {
> + 0x04000000, //64MB
> + 0x08000000, //128MB
> + 0x10000000, //256MB
> + 0x20000000, //512MB
> +};
You could perhaps save us from the size comments here by using e.g.
static const u32 ast2400_dram_table[] = {
64 << 20,
128 << 20,
256 << 20,
512 << 20,
};
> +
> +static const u32 ast2500_dram_table[] = {
> + 0x08000000, //128MB
> + 0x10000000, //256MB
> + 0x20000000, //512MB
> + 0x40000000, //1024MB
> +};
> +
> +static const u32 ast2600_dram_table[] = {
> + 0x10000000, //256MB
> + 0x20000000, //512MB
> + 0x40000000, //1024MB
> + 0x80000000, //2048MB
> +};
> +
> +extern u32 aspeed_get_dram_size(void)
> +{
> + u32 reg04;
> + u32 size;
> +
> + regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> +
> +#if defined(CONFIG_MACH_ASPEED_G6)
> + size = ast2600_dram_table[reg04 & 0x3];
> +#elif defined(CONFIG_MACH_ASPEED_G5)
> + size = ast2500_dram_table[reg04 & 0x3];
> +#else
> + size = ast2400_dram_table[reg04 & 0x3];
> +#endif
> + return size;
> +}
> +EXPORT_SYMBOL(aspeed_get_dram_size);
The driver must support running on any of the SoC generations without being
recompiled. This requires the driver be compiled for a specific SoC generation.
The right way to do this is to use the OF match table data. Please fix it.
> +
> +static const u32 aspeed_vga_table[] = {
> + 0x800000, //8MB
> + 0x1000000, //16MB
> + 0x2000000, //32MB
> + 0x4000000, //64MB
> +};
> +
> +extern u32 aspeed_get_vga_size(void)
> +{
> + u32 reg04;
> + u32 size;
> +
> + regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> +
> + size = aspeed_vga_table[((reg04 & 0xC) >> 2)];
> + return size;
> +}
> +EXPORT_SYMBOL(aspeed_get_vga_size);
> +
> static bool regmap_is_volatile(struct device *dev, unsigned int reg)
> {
> switch (reg) {
> @@ -209,8 +275,8 @@ static int config_irq(void *ctx, struct
> platform_device *pdev)
> /* register interrupt handler */
> irq = platform_get_irq(pdev, 0);
> dev_dbg(&pdev->dev, "got irq %d\n", irq);
> - if (irq < 0)
> - return irq;
> + if (!irq)
> + return -ENODEV;
The documentation for platform_get_irq() says "Return: IRQ number on success, negative error number on failure."
So this change doesn't look right.
>
> rc = devm_request_irq(&pdev->dev, irq, mcr_isr, IRQF_TRIGGER_HIGH,
> DRV_NAME, ctx);
> @@ -239,7 +305,11 @@ static int init_csrows(struct mem_ctl_info *mci)
> int rc;
>
> /* retrieve info about physical memory from device tree */
> - np = of_find_node_by_path("/memory");
> +#ifdef CONFIG_MACH_ASPEED_G4
> + np = of_find_node_by_path("/memory@40000000");
> +#else
> + np = of_find_node_by_path("/memory@80000000");
> +#endif
Again, this makes the driver SoC-specific at compile time, and that's not going
to fly. If we need it, this should be solved with a phandle to the appropriate
memory node.
> if (!np) {
> dev_err(mci->pdev, "dt: missing /memory node\n");
> return -ENODEV;
> @@ -281,11 +351,19 @@ static int aspeed_probe(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct edac_mc_layer layers[2];
> struct mem_ctl_info *mci;
> + struct device_node *np;
> + struct resource *res;
> void __iomem *regs;
> - u32 reg04;
> int rc;
>
> - regs = devm_platform_ioremap_resource(pdev, 0);
> + /* setup regmap */
> + np = dev->of_node;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res)
> + return -ENOENT;
> +
> + regs = devm_ioremap_resource(dev, res);
> if (IS_ERR(regs))
> return PTR_ERR(regs);
Why is this change necessary?
>
> @@ -294,13 +372,6 @@ static int aspeed_probe(struct platform_device *pdev)
> if (IS_ERR(aspeed_regmap))
> return PTR_ERR(aspeed_regmap);
>
> - /* bail out if ECC mode is not configured */
> - regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> - if (!(reg04 & ASPEED_MCR_CONF_ECC)) {
> - dev_err(&pdev->dev, "ECC mode is not configured in u-boot\n");
> - return -EPERM;
> - }
> -
Why shouldn't we do this check?
> edac_op_state = EDAC_OPSTATE_INT;
>
> /* allocate & init EDAC MC data structure */
> @@ -373,13 +444,13 @@ static int aspeed_remove(struct platform_device *pdev)
> return 0;
> }
>
> -
> static const struct of_device_id aspeed_of_match[] = {
> + { .compatible = "aspeed,ast2400-sdram-edac" },
> { .compatible = "aspeed,ast2500-sdram-edac" },
> + { .compatible = "aspeed,ast2600-sdram-edac" },
The .data member of struct of_device_id is where you need to attach your
SoC-generation-specific data.
Cheers,
Andrew
> {},
> };
>
> -
> static struct platform_driver aspeed_driver = {
> .driver = {
> .name = DRV_NAME,
> @@ -395,18 +466,15 @@ static int __init aspeed_init(void)
> return platform_driver_register(&aspeed_driver);
> }
>
> -
> static void __exit aspeed_exit(void)
> {
> platform_driver_unregister(&aspeed_driver);
> }
>
> -
> module_init(aspeed_init);
> module_exit(aspeed_exit);
>
> -
> MODULE_LICENSE("GPL");
> MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
> -MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
> +MODULE_DESCRIPTION("Aspeed EDAC driver");
> MODULE_VERSION("1.0");
> --
> 2.17.1
>
>
Hi Andrew,
Great suggestion, responses inline below. We'll remove build-time SoC dependency driver code and submit an updated v2 patch.
Thanks,
Troy Lee
> -----Original Message-----
> From: Andrew Jeffery <[email protected]>
> Sent: Tuesday, December 1, 2020 9:12 AM
> To: Troy Lee <[email protected]>; Stefan M Schaeckeler
> <[email protected]>; Rob Herring <[email protected]>; Joel Stanley
> <[email protected]>; Borislav Petkov <[email protected]>; Mauro Carvalho Chehab
> <[email protected]>; Tony Luck <[email protected]>; James Morse
> <[email protected]>; Robert Richter <[email protected]>; open
> list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <[email protected]>; moderated list:ARM/ASPEED MACHINE
> SUPPORT <[email protected]>; moderated
> list:ARM/ASPEED MACHINE SUPPORT <[email protected]>; open
> list <[email protected]>; open list:EDAC-CORE
> <[email protected]>
> Cc: [email protected]; Ryan Chen <[email protected]>
> Subject: Re: [PATCH 3/3] edac: Supporting AST2400 and AST2600 edac driver
>
> Hi Troy,
>
> I like the idea of expanding the driver's support to cover the other SoC
> generations, but not at the cost of making the build of the driver SoC-specific.
> I've made some comments below in this regard.
>
> On Mon, 30 Nov 2020, at 19:03, Troy Lee wrote:
> > Adding AST2400 and AST2600 edac driver support.
> >
> > Signed-off-by: Troy Lee <[email protected]>
> > ---
> > drivers/edac/Kconfig | 6 +-
> > drivers/edac/aspeed_edac.c | 114
> > +++++++++++++++++++++++++++++--------
> > 2 files changed, 94 insertions(+), 26 deletions(-)
> >
> > diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig index
> > fc30f2ef9782..8ea70746d0bf 100644
> > --- a/drivers/edac/Kconfig
> > +++ b/drivers/edac/Kconfig
> > @@ -508,10 +508,10 @@ config EDAC_QCOM
> > health, you should probably say 'Y' here.
> >
> > config EDAC_ASPEED
> > - tristate "Aspeed AST 2500 SoC"
> > - depends on MACH_ASPEED_G5
> > + tristate "Aspeed AST BMC SoC"
> > + depends on (MACH_ASPEED_G4 || MACH_ASPEED_G5 ||
> MACH_ASPEED_G6)
> > help
> > - Support for error detection and correction on the Aspeed AST 2500 SoC.
> > + Support for error detection and correction on the Aspeed AST BMC SoC.
> >
> > First, ECC must be configured in the bootloader. Then, this driver
> > will expose error counters via the EDAC kernel framework.
> > diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
> > index fbec28dc661d..03a3c12f6bf6 100644
> > --- a/drivers/edac/aspeed_edac.c
> > +++ b/drivers/edac/aspeed_edac.c
> > @@ -14,12 +14,11 @@
> > #include <linux/regmap.h>
> > #include "edac_module.h"
> >
> > -
> > #define DRV_NAME "aspeed-edac"
> >
> > -
> > #define ASPEED_MCR_PROT 0x00 /* protection key register */
> > #define ASPEED_MCR_CONF 0x04 /* configuration register */
> > +#define ASPEED_MCR_REQ 0x08 /* Graphics Memory Protection
> register */
> > #define ASPEED_MCR_INTR_CTRL 0x50 /* interrupt control/status
> register */
> > #define ASPEED_MCR_ADDR_UNREC 0x58 /* address of first
> un-recoverable error */
> > #define ASPEED_MCR_ADDR_REC 0x5c /* address of last recoverable
> error */
> > @@ -34,10 +33,8 @@
> > #define ASPEED_MCR_INTR_CTRL_CNT_UNREC GENMASK(15, 12)
> #define
> > ASPEED_MCR_INTR_CTRL_ENABLE (BIT(0) | BIT(1))
> >
> > -
> > static struct regmap *aspeed_regmap;
> >
> > -
> > static int regmap_reg_write(void *context, unsigned int reg, unsigned
> > int val) {
> > void __iomem *regs = (void __iomem *)context; @@ -53,7 +50,6 @@
> > static int regmap_reg_write(void *context, unsigned int reg, unsigned
> > int val)
> > return 0;
> > }
> >
> > -
> > static int regmap_reg_read(void *context, unsigned int reg, unsigned
> > int *val) {
> > void __iomem *regs = (void __iomem *)context; @@ -63,6 +59,76 @@
> > static int regmap_reg_read(void *context, unsigned int reg, unsigned
> > int *val)
> > return 0;
> > }
> >
> > +extern void aspeed_sdmc_disable_mem_protection(u8 req) {
> > + u32 req_val = 0;
> > +
> > + regmap_read(aspeed_regmap, ASPEED_MCR_REQ, &req_val);
> > +
> > + req_val &= ~BIT(req);
> > +
> > + regmap_write(aspeed_regmap, ASPEED_MCR_REQ, req_val); }
> > +EXPORT_SYMBOL(aspeed_sdmc_disable_mem_protection);
> > +
> > +static const u32 ast2400_dram_table[] = {
> > + 0x04000000, //64MB
> > + 0x08000000, //128MB
> > + 0x10000000, //256MB
> > + 0x20000000, //512MB
> > +};
>
> You could perhaps save us from the size comments here by using e.g.
>
> static const u32 ast2400_dram_table[] = {
> 64 << 20,
> 128 << 20,
> 256 << 20,
> 512 << 20,
> };
>
Fixed all in v2.
> > +
> > +static const u32 ast2500_dram_table[] = {
> > + 0x08000000, //128MB
> > + 0x10000000, //256MB
> > + 0x20000000, //512MB
> > + 0x40000000, //1024MB
> > +};
> > +
> > +static const u32 ast2600_dram_table[] = {
> > + 0x10000000, //256MB
> > + 0x20000000, //512MB
> > + 0x40000000, //1024MB
> > + 0x80000000, //2048MB
> > +};
> > +
> > +extern u32 aspeed_get_dram_size(void) {
> > + u32 reg04;
> > + u32 size;
> > +
> > + regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> > +
> > +#if defined(CONFIG_MACH_ASPEED_G6)
> > + size = ast2600_dram_table[reg04 & 0x3]; #elif
> > +defined(CONFIG_MACH_ASPEED_G5)
> > + size = ast2500_dram_table[reg04 & 0x3]; #else
> > + size = ast2400_dram_table[reg04 & 0x3]; #endif
> > + return size;
> > +}
> > +EXPORT_SYMBOL(aspeed_get_dram_size);
>
> The driver must support running on any of the SoC generations without being
> recompiled. This requires the driver be compiled for a specific SoC generation.
>
> The right way to do this is to use the OF match table data. Please fix it.
>
Fixed in v2, driver can check the DRAM controller hardware version from MCR_CONF [31:28].
> > +
> > +static const u32 aspeed_vga_table[] = {
> > + 0x800000, //8MB
> > + 0x1000000, //16MB
> > + 0x2000000, //32MB
> > + 0x4000000, //64MB
> > +};
> > +
> > +extern u32 aspeed_get_vga_size(void)
> > +{
> > + u32 reg04;
> > + u32 size;
> > +
> > + regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> > +
> > + size = aspeed_vga_table[((reg04 & 0xC) >> 2)];
> > + return size;
> > +}
> > +EXPORT_SYMBOL(aspeed_get_vga_size);
> > +
> > static bool regmap_is_volatile(struct device *dev, unsigned int reg)
> > {
> > switch (reg) {
> > @@ -209,8 +275,8 @@ static int config_irq(void *ctx, struct
> > platform_device *pdev)
> > /* register interrupt handler */
> > irq = platform_get_irq(pdev, 0);
> > dev_dbg(&pdev->dev, "got irq %d\n", irq);
> > - if (irq < 0)
> > - return irq;
> > + if (!irq)
> > + return -ENODEV;
>
> The documentation for platform_get_irq() says "Return: IRQ number on
> success, negative error number on failure."
>
> So this change doesn't look right.
>
Fixed in v2.
> >
> > rc = devm_request_irq(&pdev->dev, irq, mcr_isr, IRQF_TRIGGER_HIGH,
> > DRV_NAME, ctx);
> > @@ -239,7 +305,11 @@ static int init_csrows(struct mem_ctl_info *mci)
> > int rc;
> >
> > /* retrieve info about physical memory from device tree */
> > - np = of_find_node_by_path("/memory");
> > +#ifdef CONFIG_MACH_ASPEED_G4
> > + np = of_find_node_by_path("/memory@40000000");
> > +#else
> > + np = of_find_node_by_path("/memory@80000000");
> > +#endif
>
> Again, this makes the driver SoC-specific at compile time, and that's not going
> to fly. If we need it, this should be solved with a phandle to the appropriate
> memory node.
>
Fixed in v2 by using of_find_node_by_name(NULL, "memory") instead.
> > if (!np) {
> > dev_err(mci->pdev, "dt: missing /memory node\n");
> > return -ENODEV;
> > @@ -281,11 +351,19 @@ static int aspeed_probe(struct platform_device
> *pdev)
> > struct device *dev = &pdev->dev;
> > struct edac_mc_layer layers[2];
> > struct mem_ctl_info *mci;
> > + struct device_node *np;
> > + struct resource *res;
> > void __iomem *regs;
> > - u32 reg04;
> > int rc;
> >
> > - regs = devm_platform_ioremap_resource(pdev, 0);
> > + /* setup regmap */
> > + np = dev->of_node;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res)
> > + return -ENOENT;
> > +
> > + regs = devm_ioremap_resource(dev, res);
> > if (IS_ERR(regs))
> > return PTR_ERR(regs);
>
> Why is this change necessary?
>
Not necessary, so I'll reverted this part of change in v2.
> >
> > @@ -294,13 +372,6 @@ static int aspeed_probe(struct platform_device
> *pdev)
> > if (IS_ERR(aspeed_regmap))
> > return PTR_ERR(aspeed_regmap);
> >
> > - /* bail out if ECC mode is not configured */
> > - regmap_read(aspeed_regmap, ASPEED_MCR_CONF, ®04);
> > - if (!(reg04 & ASPEED_MCR_CONF_ECC)) {
> > - dev_err(&pdev->dev, "ECC mode is not configured in u-boot\n");
> > - return -EPERM;
> > - }
> > -
>
> Why shouldn't we do this check?
The driver can handle both ECC on and off, so this check might not be necessary.
> > edac_op_state = EDAC_OPSTATE_INT;
> >
> > /* allocate & init EDAC MC data structure */ @@ -373,13 +444,13 @@
> > static int aspeed_remove(struct platform_device *pdev)
> > return 0;
> > }
> >
> > -
> > static const struct of_device_id aspeed_of_match[] = {
> > + { .compatible = "aspeed,ast2400-sdram-edac" },
> > { .compatible = "aspeed,ast2500-sdram-edac" },
> > + { .compatible = "aspeed,ast2600-sdram-edac" },
>
> The .data member of struct of_device_id is where you need to attach your
> SoC-generation-specific data.
>
> Cheers,
>
> Andrew
>
> > {},
> > };
> >
> > -
> > static struct platform_driver aspeed_driver = {
> > .driver = {
> > .name = DRV_NAME,
> > @@ -395,18 +466,15 @@ static int __init aspeed_init(void)
> > return platform_driver_register(&aspeed_driver);
> > }
> >
> > -
> > static void __exit aspeed_exit(void)
> > {
> > platform_driver_unregister(&aspeed_driver);
> > }
> >
> > -
> > module_init(aspeed_init);
> > module_exit(aspeed_exit);
> >
> > -
> > MODULE_LICENSE("GPL");
> > MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
> > -MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
> > +MODULE_DESCRIPTION("Aspeed EDAC driver");
> > MODULE_VERSION("1.0");
> > --
> > 2.17.1
> >
> >
Hi Stefan,
The driver was ported from latest ASPEED BSP, so I only test with ECC-on/off
from u-boot and check if driver runs correctly.
The test doc you provided is very nice and detailed, I'll try to reproduce the
injection test in v2 patch.
Thanks,
Troy Lee
> -----Original Message-----
> From: Stefan Schaeckeler (sschaeck) <[email protected]>
> Sent: Monday, November 30, 2020 5:16 PM
> To: Troy Lee <[email protected]>; Rob Herring <[email protected]>;
> Joel Stanley <[email protected]>; Andrew Jeffery <[email protected]>; Borislav
> Petkov <[email protected]>; Mauro Carvalho Chehab <[email protected]>;
> Tony Luck <[email protected]>; James Morse <[email protected]>;
> Robert Richter <[email protected]>; open list:OPEN FIRMWARE AND
> FLATTENED DEVICE TREE BINDINGS <[email protected]>; moderated
> list:ARM/ASPEED MACHINE SUPPORT <[email protected]>;
> moderated list:ARM/ASPEED MACHINE SUPPORT
> <[email protected]>; open list <[email protected]>;
> open list:EDAC-CORE <[email protected]>
> Cc: [email protected]; Ryan Chen <[email protected]>; Stefan
> Schaeckeler <[email protected]>
> Subject: Re: [PATCH 3/3] edac: Supporting AST2400 and AST2600 edac driver
>
> Hello Troy,
>
> > Adding AST2400 and AST2600 edac driver support.
> >
> > Signed-off-by: Troy Lee <[email protected]>
> > ---
> > drivers/edac/Kconfig | 6 +-
> > drivers/edac/aspeed_edac.c | 114 +++++++++++++++++++++++++++++--------
> > 2 files changed, 94 insertions(+), 26 deletions(-)
>
> Uh, there are quite some non-trivial changes. I'll have a look over the coming
> weekend.
>
> Testing an edac driver comes with challenges. Did you test your code? If so,
> how?
>
> That's how I was testing my original edac 2500 driver
> http://students.engr.scu.edu/~sschaeck/misc/aspeed-edac.html
>
> Stefan
Hello Troy,
> Hi Stefan,
>
> The driver was ported from latest ASPEED BSP, so I only test with ECC-on/off
> from u-boot and check if driver runs correctly.
I noticed now most changes are these "exports". As you removed them a later revision, the patch looks now lean and clean. I'll give you my Reviewed-by tag after you addressed Andrew's last comment.
> The test doc you provided is very nice and detailed, I'll try to reproduce the
> injection test in v2 patch.
It does not harm to redo the testing. That is time-consuming and with your current, now trivial changes, it's not really necessary.
Stefan