No obvous reason. Works fine with kernel 2.6.10
Result of lspci:
00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02)
00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O Control
Registers (rev 02)
00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration
Process Registers (rev 02)
00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated
Graphics Device (rev 02)
00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics
Device (rev 02)
00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 01)
00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller
(rev 01)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01)
00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage
Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97
Audio Controller (rev 01)
00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller (rev 01)
02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev
01)
02:02.0 Network controller: Broadcom Corporation: Unknown device 4324 (rev
03)
02:04.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus
Controller
Diff of .config between 2.6.10 & 2.6.11
--- linux-2.6.10/.config 2005-02-19 18:33:49.000000000 -0800
+++ linux-2.6.11/.config 2005-03-02 12:11:54.000000000 -0800
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.10
-# Sat Feb 19 17:34:02 2005
+# Linux kernel version: 2.6.11
+# Wed Mar 2 12:11:54 2005
#
CONFIG_X86=y
CONFIG_MMU=y
@@ -92,6 +92,7 @@
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
@@ -102,6 +103,7 @@
# CONFIG_HPET_TIMER is not set
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
+CONFIG_PREEMPT_BKL=y
# CONFIG_X86_UP_APIC is not set
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
@@ -158,6 +160,7 @@
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
+# CONFIG_ACPI_CONTAINER is not set
#
# APM (Advanced Power Management) BIOS Support
@@ -176,7 +179,8 @@
#
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_DEBUG is not set
-# CONFIG_CPU_FREQ_PROC_INTF is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
@@ -216,6 +220,7 @@
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
+# CONFIG_PCIEPORTBUS is not set
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
# CONFIG_ISA is not set
@@ -227,7 +232,6 @@
#
CONFIG_PCCARD=y
CONFIG_PCMCIA_DEBUG=y
-CONFIG_PCMCIA_OBSOLETE=y
CONFIG_PCMCIA=y
CONFIG_CARDBUS=y
@@ -238,6 +242,7 @@
CONFIG_PD6729=y
CONFIG_I82092=y
CONFIG_TCIC=y
+CONFIG_PCCARD_NONSTATIC=y
#
# PCI Hotplug Support
@@ -291,6 +296,7 @@
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
@@ -313,6 +319,7 @@
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
+# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
@@ -406,6 +413,7 @@
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
#
# SCSI low-level drivers
@@ -426,6 +434,7 @@
CONFIG_SCSI_ATA_PIIX=y
# CONFIG_SCSI_SATA_NV is not set
# CONFIG_SCSI_SATA_PROMISE is not set
+# CONFIG_SCSI_SATA_QSTOR is not set
CONFIG_SCSI_SATA_SX4=m
# CONFIG_SCSI_SATA_SIL is not set
CONFIG_SCSI_SATA_SIS=m
@@ -454,7 +463,6 @@
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
-# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
@@ -579,7 +587,6 @@
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_IP_NF_TARGET_NETMAP=y
CONFIG_IP_NF_TARGET_SAME=y
-# CONFIG_IP_NF_NAT_LOCAL is not set
# CONFIG_IP_NF_NAT_SNMP_BASIC is not set
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
@@ -798,6 +805,7 @@
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
CONFIG_SERIO_PCIPS2=y
+CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
#
@@ -968,6 +976,7 @@
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
@@ -986,7 +995,7 @@
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
-# CONFIG_SND_RTCTIMER is not set
+CONFIG_SND_RTCTIMER=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
@@ -1014,6 +1023,8 @@
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
+# CONFIG_SND_EMU10K1X is not set
+# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
@@ -1037,6 +1048,7 @@
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
+# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
#
@@ -1129,7 +1141,6 @@
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
@@ -1163,7 +1174,6 @@
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
-# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
@@ -1172,6 +1182,7 @@
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_TEST is not set
#
@@ -1189,6 +1200,11 @@
# CONFIG_MMC is not set
#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
# File systems
#
CONFIG_EXT2_FS=y
@@ -1202,6 +1218,10 @@
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
+
+#
+# XFS support
+#
# CONFIG_XFS_FS is not set
CONFIG_MINIX_FS=y
# CONFIG_ROMFS_FS is not set
@@ -1223,7 +1243,7 @@
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
-CONFIG_MSDOS_FS=y
+# CONFIG_MSDOS_FS is not set
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
@@ -1267,7 +1287,6 @@
#
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
-# CONFIG_EXPORTFS is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=y
@@ -1338,6 +1357,8 @@
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
+CONFIG_DEBUG_PREEMPT=y
+CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_FRAME_POINTER is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_4KSTACKS is not set
@@ -1354,6 +1375,10 @@
# CONFIG_CRYPTO is not set
#
+# Hardware crypto devices
+#
+
+#
# Library routines
#
CONFIG_CRC_CCITT=m
> > > Does it work with i8042.noacpi kernel boot parameter?
> > >
> > Yes, it does.
> Btw, when it boots _without_ this option is there any messages from
> i8042 or ACPI?
>
A few. I'll go back and catch them for you.
Relevent messages (erring on the heavy side)
ACPI: RSDP (v000 DELL ) @ 0x000fdf00
ACPI: RSDT (v001 DELL CPi R 0x27d4061d ASL 0x00000061) @ 0x1fef0000
ACPI: FADT (v001 DELL CPi R 0x27d4061d ASL 0x00000061) @ 0x1fef0400
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
...
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
...
i8k: unable to get SMM Dell signature
i8k: unable to get SMM BIOS version
...
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
...
apm: BIOS not found.
NTFS driver 2.1.22 [Flags: R/W].
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (56 C)
...
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
...
i8042: ACPI detection disabled
i8042.c: Warning: Keylock active.
...
i8042: ACPI detection disabled
i8042.c: Warning: Keylock active.
...
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 7 (level, low) -> IRQ 7
On Wednesday 02 March 2005 21:27, Joshua Hudson wrote:
> i8042: ACPI detection disabled
> i8042.c: Warning: Keylock active.
I really need dmesg when booting _without_ the option, i.e. non-working case.
Thanks!
--
Dmitry
On Wed, 2 Mar 2005, Dmitry Torokhov wrote:
> On Wed, 2 Mar 2005 13:26:18 -0800 (PST), Joshua Hudson
> <[email protected]> wrote:
> > No obvous reason. Works fine with kernel 2.6.10
>
> Does it work with i8042.noacpi kernel boot parameter?
>
Yes, it does. I never heard of that option before, or any
one like it.
On Wednesday 02 March 2005 21:01, Joshua Hudson wrote:
>
> On Wed, 2 Mar 2005, Dmitry Torokhov wrote:
>
> > On Wed, 2 Mar 2005 13:26:18 -0800 (PST), Joshua Hudson
> > <[email protected]> wrote:
> > > No obvous reason. Works fine with kernel 2.6.10
> >
> > Does it work with i8042.noacpi kernel boot parameter?
> >
> Yes, it does. I never heard of that option before, or any
> one like it.
It is a new one.
Btw, when it boots _without_ this option is there any messages from
i8042 or ACPI?
--
Dmitry
PCI: Using ACPI for IRQ routing
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (59 C)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PS/2 Keyboard Controller [KBC] at I/O 0x60, 0x66, irq 1
ACPI: PS/2 Mouse Controller [PS2M] at irq 12
i8042.c: Can't read CTR while initializing i8042.
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 7 (level, low) -> IRQ 7
ACPI wakeup devices:
ACPI: (supports S0 S1 S3 S4 S4bios S5)
More like it, hmmm?
On Wednesday 02 March 2005 23:02, Joshua Hudson wrote:
> ACPI: PS/2 Keyboard Controller [KBC] at I/O 0x60, 0x66, irq 1
> ACPI: PS/2 Mouse Controller [PS2M] at irq 12
> i8042.c: Can't read CTR while initializing i8042.
Ok, your BIOS is also reporting incorrect port values for the keyboard
controller, it should be 0x60, 0x64. You'll have to use i8042.noacpi
for now.
Thank you for the log.
--
Dmitry
Joshua Hudson wrote:
> No obvous reason. Works fine with kernel 2.6.10
>
> Result of lspci:
> 00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02)
> 00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O Control
> Registers (rev 02)
> 00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration
> Process Registers (rev 02)
> 00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated
> Graphics Device (rev 02)
> 00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics
> Device (rev 02)
> 00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 01)
> 00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 01)
> 00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 01)
> 00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller
> (rev 01)
> 00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81)
> 00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01)
> 00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage
> Controller (rev 01)
> 00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97
> Audio Controller (rev 01)
> 00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller (rev 01)
> 02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev
> 01)
> 02:02.0 Network controller: Broadcom Corporation: Unknown device 4324 (rev
> 03)
> 02:04.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus
> Controller
>
ditto with Inspiron 5150
lspci:
0000:00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller (rev 02)
0000:00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller (rev 02)
0000:00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller (rev 02)
0000:00:01.0 PCI bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to AGP Controller (rev 02)
0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M)
USB2 EHCI Controller (rev 01)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
0000:00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface
Bridge (rev 01)
0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE
Controller (rev 01)
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV34M [GeForce FX
Go 5200] (rev a1)
0000:02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T
(rev 01)
0000:02:04.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus
Controller (rev 02)
0000:02:04.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394
Controller
On Wed, 2 Mar 2005 13:26:18 -0800 (PST), Joshua Hudson
<[email protected]> wrote:
> No obvous reason. Works fine with kernel 2.6.10
Does it work with i8042.noacpi kernel boot parameter?
--
Dmitry