Hi, all,
Are there existing tools to test the network driver
latency (between time to start the interrupt handler (irq.c) and time to
start tasklet (bh))?
Thanks!
Xinwen Fu
On Thu, 4 Jul 2002, george anzinger wrote:
> Xinwen - Fu wrote:
> >
> > In fact I want a timer (either in user level or kernel level).
> > This timer (hope it is a periodic timer) must expire at the interval that
> > I specify. For example, if I
> > want that the timer expires at 10ms, it should never be fired at
> > 10.0000000001ms or
> > 9.9999999999ms. That is the key part that I want!
>
> 10 nines! Lots of luck. You need to spend a LOT more money
> than I have. Cesium clocks may be able to do this, but not
> computers...
>
> But first, please define "fire". If you mean that the
> interrupt is generated at this rate, well we can do maybe 4
> or 5 nines. If, on the other hand you mean "your timer
> function gets cpu cycles", I don't think you will find a
> machine that can do much better than one or 2 nines. Even
> if the timer is the only interrupt, you still have interrupt
> off times and cache indeterminism to contend with.
>
> If the idea is to to "tickle" some hardware with this
> signal, you will do better to not involve a computer in the
> link.
>
> The utime project had some software that would schedule a
> timer tick early and then loop reading the TSC until the
> "exact" time. This still has the problems of interrupts and
> cache misses, but it is probably the only way to approach
> what you want. Nothing magic, you just figure the worst
> case latency and set your timer to expire early enough to be
> ahead of the appointed time. Then you loop on the TSC
> waiting for your exact time.
>
> -g
> >
> > Have an idea?
> >
> > Thanks!
> >
> > Xinwen Fu
> >
> > On Thu, 4 Jul 2002, george anzinger wrote:
> >
> > > "Richard B. Johnson" wrote:
> > > >
> > > > On Wed, 3 Jul 2002, Xinwen - Fu wrote:
> > > >
> > > > > Hi, all,
> > > > > I'm curious that if a network card interrupt happens at the same
> > > > > time as the kernel timer expires, what will happen?
> > > > >
> > > > > It's said the kernel timer is guaranteed accurate. But if
> > > > > interrupts are not masked off, the network interrupt also should get
> > > > > response when a kernel timer expires. So I don't know who will preempt
> > > > > who.
> > > > >
> > > > > Thanks for information!
> > > > >
> > > > > Xinwen Fu
> > > >
> > > > The highest priority interrupt will get serviced first. It's the timer.
> > > > Interrupts are serviced in priority-order. Hardware "remembers" which
> > > > ones are pending so none are lost if some driver doesn't do something
> > > > stupid.
> > >
> > > That is true as far as it goes, HOWEVER, timers are serviced
> > > by bottom half code which is run at the end of the
> > > interrupt, WITH THE INTERRUPT SYSTEM ON. Therefore, timer
> > > servicing can be interrupted by an interrupt and thus be
> > > delayed.
> > >
> > > --
> > > George Anzinger [email protected]
> > > High-res-timers:
> > > http://sourceforge.net/projects/high-res-timers/
> > > Real time sched: http://sourceforge.net/projects/rtsched/
> > > Preemption patch:
> > > http://www.kernel.org/pub/linux/kernel/people/rml
> > >
>
> --
> George Anzinger [email protected]
> High-res-timers:
> http://sourceforge.net/projects/high-res-timers/
> Real time sched: http://sourceforge.net/projects/rtsched/
> Preemption patch:
> http://www.kernel.org/pub/linux/kernel/people/rml
>