JZ4750/55/60 (but not JZ4760b) have an extra divisor in between extclk
and peripheral clock, called CPCCR.ECS, the driver can't figure out the
real state of the divisor without dirty hack - peek CGU CPCCR register.
However, we can rely on a vendor's bootloader (u-boot 1.1.6) behavior:
if (extclk > 16MHz)
the divisor is enabled, so the UART driving clock is extclk/2.
This behavior relies on hardware differences: most boards (if not all)
with those SoCs have 12 or 24 MHz oscillators but many peripherals want
12Mhz to operate properly (AIC and USB-PHY at least).
The patch doesn't affect JZ4760's behavior as it is subject for another
patchset with re-classification of all supported ingenic UARTs.
Link: https://github.com/carlos-wong/uboot_jz4755/blob/master/cpu/mips/jz_serial.c#L158
Signed-off-by: Siarhei Volkau <[email protected]>
---
drivers/tty/serial/8250/8250_ingenic.c | 50 ++++++++++++++++++++++----
1 file changed, 43 insertions(+), 7 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_ingenic.c b/drivers/tty/serial/8250/8250_ingenic.c
index 2b2f5d8d2..3ffa6b722 100644
--- a/drivers/tty/serial/8250/8250_ingenic.c
+++ b/drivers/tty/serial/8250/8250_ingenic.c
@@ -87,24 +87,19 @@ static void __init ingenic_early_console_setup_clock(struct earlycon_device *dev
dev->port.uartclk = be32_to_cpup(prop);
}
-static int __init ingenic_early_console_setup(struct earlycon_device *dev,
- const char *opt)
+static int __init ingenic_earlycon_setup_tail(struct earlycon_device *dev,
+ const char *opt)
{
struct uart_port *port = &dev->port;
unsigned int divisor;
int baud = 115200;
- if (!dev->port.membase)
- return -ENODEV;
-
if (opt) {
unsigned int parity, bits, flow; /* unused for now */
uart_parse_options(opt, &baud, &parity, &bits, &flow);
}
- ingenic_early_console_setup_clock(dev);
-
if (dev->baud)
baud = dev->baud;
divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud);
@@ -129,9 +124,49 @@ static int __init ingenic_early_console_setup(struct earlycon_device *dev,
return 0;
}
+static int __init ingenic_early_console_setup(struct earlycon_device *dev,
+ const char *opt)
+{
+ if (!dev->port.membase)
+ return -ENODEV;
+
+ ingenic_early_console_setup_clock(dev);
+
+ ingenic_earlycon_setup_tail(dev, opt);
+}
+
+static int __init jz4750_early_console_setup(struct earlycon_device *dev,
+ const char *opt)
+{
+ if (!dev->port.membase)
+ return -ENODEV;
+
+ /*
+ * JZ4750/55/60 (not JZ4760b) have an extra divisor
+ * between extclk and peripheral clock, the
+ * driver can't figure out the real state of the
+ * divisor without dirty hacks (peek CGU register).
+ * However, we can rely on a vendor's behavior:
+ * if (extclk > 16MHz)
+ * the divisor is enabled.
+ * This behavior relies on hardware differences:
+ * most boards with those SoCs have 12 or 24 MHz
+ * oscillators but many peripherals want 12Mhz
+ * to operate properly (AIC and USB-phy at least).
+ */
+ ingenic_early_console_setup_clock(dev);
+ if (dev->port.uartclk > 16000000)
+ dev->port.uartclk /= 2;
+
+ ingenic_earlycon_setup_tail(dev, opt);
+}
+
OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart",
ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4750_uart, "ingenic,jz4750-uart",
+ jz4750_early_console_setup);
+
OF_EARLYCON_DECLARE(jz4770_uart, "ingenic,jz4770-uart",
ingenic_early_console_setup);
@@ -328,6 +363,7 @@ static const struct ingenic_uart_config x1000_uart_config = {
static const struct of_device_id of_match[] = {
{ .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config },
+ { .compatible = "ingenic,jz4750-uart", .data = &jz4760_uart_config },
{ .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config },
{ .compatible = "ingenic,jz4770-uart", .data = &jz4760_uart_config },
{ .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config },
--
2.36.1
Hi Siarhei,
Le sam. 22 oct. 2022 ? 18:12:24 +0300, Siarhei Volkau
<[email protected]> a ?crit :
> JZ4750/55/60 (but not JZ4760b) have an extra divisor in between extclk
> and peripheral clock, called CPCCR.ECS, the driver can't figure out
> the
> real state of the divisor without dirty hack - peek CGU CPCCR
> register.
> However, we can rely on a vendor's bootloader (u-boot 1.1.6) behavior:
> if (extclk > 16MHz)
> the divisor is enabled, so the UART driving clock is extclk/2.
>
> This behavior relies on hardware differences: most boards (if not all)
> with those SoCs have 12 or 24 MHz oscillators but many peripherals
> want
> 12Mhz to operate properly (AIC and USB-PHY at least).
>
> The patch doesn't affect JZ4760's behavior as it is subject for
> another
> patchset with re-classification of all supported ingenic UARTs.
>
> Link:
> https://github.com/carlos-wong/uboot_jz4755/blob/master/cpu/mips/jz_serial.c#L158
> Signed-off-by: Siarhei Volkau <[email protected]>
> ---
> drivers/tty/serial/8250/8250_ingenic.c | 50
> ++++++++++++++++++++++----
> 1 file changed, 43 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_ingenic.c
> b/drivers/tty/serial/8250/8250_ingenic.c
> index 2b2f5d8d2..3ffa6b722 100644
> --- a/drivers/tty/serial/8250/8250_ingenic.c
> +++ b/drivers/tty/serial/8250/8250_ingenic.c
> @@ -87,24 +87,19 @@ static void __init
> ingenic_early_console_setup_clock(struct earlycon_device *dev
> dev->port.uartclk = be32_to_cpup(prop);
> }
>
> -static int __init ingenic_early_console_setup(struct earlycon_device
> *dev,
> - const char *opt)
> +static int __init ingenic_earlycon_setup_tail(struct earlycon_device
> *dev,
> + const char *opt)
> {
> struct uart_port *port = &dev->port;
> unsigned int divisor;
> int baud = 115200;
>
> - if (!dev->port.membase)
> - return -ENODEV;
You can keep this here - no need to move it (and it'd avoid duplicating
code).
> -
> if (opt) {
> unsigned int parity, bits, flow; /* unused for now */
>
> uart_parse_options(opt, &baud, &parity, &bits, &flow);
> }
>
> - ingenic_early_console_setup_clock(dev);
> -
> if (dev->baud)
> baud = dev->baud;
> divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud);
> @@ -129,9 +124,49 @@ static int __init
> ingenic_early_console_setup(struct earlycon_device *dev,
> return 0;
> }
>
> +static int __init ingenic_early_console_setup(struct earlycon_device
> *dev,
> + const char *opt)
> +{
> + if (!dev->port.membase)
> + return -ENODEV;
> +
> + ingenic_early_console_setup_clock(dev);
> +
> + ingenic_earlycon_setup_tail(dev, opt);
> +}
> +
> +static int __init jz4750_early_console_setup(struct earlycon_device
> *dev,
> + const char *opt)
> +{
> + if (!dev->port.membase)
> + return -ENODEV;
> +
> + /*
> + * JZ4750/55/60 (not JZ4760b) have an extra divisor
> + * between extclk and peripheral clock, the
> + * driver can't figure out the real state of the
> + * divisor without dirty hacks (peek CGU register).
> + * However, we can rely on a vendor's behavior:
> + * if (extclk > 16MHz)
> + * the divisor is enabled.
> + * This behavior relies on hardware differences:
> + * most boards with those SoCs have 12 or 24 MHz
> + * oscillators but many peripherals want 12Mhz
> + * to operate properly (AIC and USB-phy at least).
> + */
> + ingenic_early_console_setup_clock(dev);
> + if (dev->port.uartclk > 16000000)
> + dev->port.uartclk /= 2;
I would assume you could just do:
dev->port.uartclk = 12000000;
Since you'd always get a 12 MHz clock (either with a 12 MHz oscillator
or a 24 MHz oscillator with a /2 divider).
With that said - I am fine with that code, it would allow to fine-tune
the oscillator value (although I hightly doubt anybody is going to do
that).
The 16 MHz value sounds very arbitrary, but I'll give it a pass.
Cheers,
-Paul
> +
> + ingenic_earlycon_setup_tail(dev, opt);
> +}
> +
> OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart",
> ingenic_early_console_setup);
>
> +OF_EARLYCON_DECLARE(jz4750_uart, "ingenic,jz4750-uart",
> + jz4750_early_console_setup);
> +
> OF_EARLYCON_DECLARE(jz4770_uart, "ingenic,jz4770-uart",
> ingenic_early_console_setup);
>
> @@ -328,6 +363,7 @@ static const struct ingenic_uart_config
> x1000_uart_config = {
>
> static const struct of_device_id of_match[] = {
> { .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config
> },
> + { .compatible = "ingenic,jz4750-uart", .data = &jz4760_uart_config
> },
> { .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config
> },
> { .compatible = "ingenic,jz4770-uart", .data = &jz4760_uart_config
> },
> { .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config
> },
> --
> 2.36.1
>