Add support for MPS VR controller mp2993. This driver exposes
telemetry and limits value readings and writtings.
Signed-off-by: Noah Wang <[email protected]>
---
V1 -> V2:
remove useless code in mp2993_set_vout_format() and
mp2993_identify()
Documentation/hwmon/index.rst | 1 +
Documentation/hwmon/mp2993.rst | 150 +++++++++++++++++++
MAINTAINERS | 7 +
drivers/hwmon/pmbus/Kconfig | 9 ++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/mp2993.c | 261 +++++++++++++++++++++++++++++++++
6 files changed, 429 insertions(+)
create mode 100644 Documentation/hwmon/mp2993.rst
create mode 100644 drivers/hwmon/pmbus/mp2993.c
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 03d313af469a..9d9d55b889f2 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -166,6 +166,7 @@ Hardware Monitoring Kernel Drivers
mp2856
mp2888
mp2975
+ mp2993
mp5023
mp5990
mpq8785
diff --git a/Documentation/hwmon/mp2993.rst b/Documentation/hwmon/mp2993.rst
new file mode 100644
index 000000000000..7a4fe0d946e0
--- /dev/null
+++ b/Documentation/hwmon/mp2993.rst
@@ -0,0 +1,150 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2993
+====================
+
+Supported chips:
+
+ * MPS mp2993
+
+ Prefix: 'mp2993'
+
+ * Datasheet
+ https://scnbwymvp-my.sharepoint.com/:f:/g/personal/admin_scnbwy_com/Eth4kX1_J1hMsaASHiOYL4QBHU5a75r-tRfLKbHnJFdKLQ?e=vxj3DF
+
+Author:
+
+ Noah Wang <[email protected]>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+MP2993 Dual Loop Digital Multi-phase Controller.
+
+Device compliant with:
+
+- PMBus rev 1.3 interface.
+
+The driver exports the following attributes via the 'sysfs' files
+for input voltage:
+
+**in1_input**
+
+**in1_label**
+
+**in1_crit**
+
+**in1_crit_alarm**
+
+**in1_lcrit**
+
+**in1_lcrit_alarm**
+
+**in1_max**
+
+**in1_max_alarm**
+
+**in1_min**
+
+**in1_min_alarm**
+
+The driver provides the following attributes for output voltage:
+
+**in2_input**
+
+**in2_label**
+
+**in2_crit**
+
+**in2_crit_alarm**
+
+**in2_lcrit**
+
+**in2_lcrit_alarm**
+
+**in3_input**
+
+**in3_label**
+
+**in3_crit**
+
+**in3_crit_alarm**
+
+**in3_lcrit**
+
+**in3_lcrit_alarm**
+
+The driver provides the following attributes for input current:
+
+**curr1_input**
+
+**curr1_label**
+
+**curr1_max**
+
+**curr1_max_alarm**
+
+The driver provides the following attributes for output current:
+
+**curr2_input**
+
+**curr2_label**
+
+**curr2_crit**
+
+**curr2_crit_alarm**
+
+**curr2_max**
+
+**curr2_max_alarm**
+
+**curr3_input**
+
+**curr3_label**
+
+**curr3_crit**
+
+**curr3_crit_alarm**
+
+**curr3_max**
+
+**curr3_max_alarm**
+
+The driver provides the following attributes for input power:
+
+**power1_input**
+
+**power1_label**
+
+The driver provides the following attributes for output power:
+
+**power2_input**
+
+**power2_label**
+
+**power3_input**
+
+**power3_label**
+
+The driver provides the following attributes for temperature:
+
+**temp1_input**
+
+**temp1_crit**
+
+**temp1_crit_alarm**
+
+**temp1_max**
+
+**temp1_max_alarm**
+
+**temp2_input**
+
+**temp2_crit**
+
+**temp2_crit_alarm**
+
+**temp2_max**
+
+**temp2_max_alarm**
diff --git a/MAINTAINERS b/MAINTAINERS
index aacccb376c28..4fdd787b1401 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15256,6 +15256,13 @@ S: Maintained
F: Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
F: drivers/video/backlight/mp3309c.c
+MPS MP2993 DRIVER
+M: Noah Wang <[email protected]>
+L: [email protected]
+S: Maintained
+F: Documentation/hwmon/mp2993.rst
+F: drivers/hwmon/pmbus/mp2993.c
+
MR800 AVERMEDIA USB FM RADIO DRIVER
M: Alexey Klimov <[email protected]>
L: [email protected]
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 08e82c457356..d875d31ce84c 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -346,6 +346,15 @@ config SENSORS_MP2975
This driver can also be built as a module. If so, the module will
be called mp2975.
+config SENSORS_MP2993
+ tristate "MPS MP2993"
+ help
+ If you say yes here you get hardware monitoring support for MPS
+ MP2993 Dual Loop Digital Multi-Phase Controller.
+
+ This driver can also be built as a module. If so, the module will
+ be called mp2993.
+
config SENSORS_MP2975_REGULATOR
depends on SENSORS_MP2975 && REGULATOR
bool "Regulator support for MPS MP2975"
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 2279b3327bbf..312d3f0c0540 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
obj-$(CONFIG_SENSORS_MP2856) += mp2856.o
obj-$(CONFIG_SENSORS_MP2888) += mp2888.o
obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
+obj-$(CONFIG_SENSORS_MP2993) += mp2993.o
obj-$(CONFIG_SENSORS_MP5023) += mp5023.o
obj-$(CONFIG_SENSORS_MP5990) += mp5990.o
obj-$(CONFIG_SENSORS_MPQ7932) += mpq7932.o
diff --git a/drivers/hwmon/pmbus/mp2993.c b/drivers/hwmon/pmbus/mp2993.c
new file mode 100644
index 000000000000..944593e13231
--- /dev/null
+++ b/drivers/hwmon/pmbus/mp2993.c
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers(MP2993)
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include "pmbus.h"
+
+#define MP2993_VOUT_OVUV_UINT 125
+#define MP2993_VOUT_OVUV_DIV 64
+#define MP2993_VIN_LIMIT_UINT 1
+#define MP2993_VIN_LIMIT_DIV 8
+#define MP2993_READ_VIN_UINT 1
+#define MP2993_READ_VIN_DIV 32
+
+#define MP2993_PAGE_NUM 2
+
+#define MP2993_RAIL1_FUNC (PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | \
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_POUT | \
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_PIN | \
+ PMBUS_HAVE_IIN | \
+ PMBUS_HAVE_STATUS_VOUT | \
+ PMBUS_HAVE_STATUS_IOUT | \
+ PMBUS_HAVE_STATUS_TEMP | \
+ PMBUS_HAVE_STATUS_INPUT)
+
+#define MP2993_RAIL2_FUNC (PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT | \
+ PMBUS_HAVE_POUT | PMBUS_HAVE_TEMP | \
+ PMBUS_HAVE_STATUS_VOUT | \
+ PMBUS_HAVE_STATUS_IOUT | \
+ PMBUS_HAVE_STATUS_TEMP | \
+ PMBUS_HAVE_STATUS_INPUT)
+
+/* Converts a linear11 data exponent to a specified value */
+static u16 mp2993_linear11_exponent_transfer(u16 word, u16 expect_exponent)
+{
+ s16 exponent, mantissa, target_exponent;
+
+ exponent = ((s16)word) >> 11;
+ mantissa = ((s16)((word & 0x7ff) << 5)) >> 5;
+ target_exponent = (s16)((expect_exponent & 0x1f) << 11) >> 11;
+
+ if (exponent > target_exponent)
+ mantissa = mantissa << (exponent - target_exponent);
+ else
+ mantissa = mantissa >> (target_exponent - exponent);
+
+ return (mantissa & 0x7ff) | ((expect_exponent << 11) & 0xf800);
+}
+
+static int
+mp2993_set_vout_format(struct i2c_client *client, int page, int format)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, page);
+ if (ret < 0)
+ return ret;
+
+ return i2c_smbus_write_byte_data(client, PMBUS_VOUT_MODE, format);
+}
+
+static int mp2993_identify(struct i2c_client *client, struct pmbus_driver_info *info)
+{
+ int ret;
+
+ /* Set vout to direct format for rail1. */
+ ret = mp2993_set_vout_format(client, 0, PB_VOUT_MODE_DIRECT);
+ if (ret < 0)
+ return ret;
+
+ /* Set vout to direct format for rail2. */
+ return mp2993_set_vout_format(client, 1, PB_VOUT_MODE_DIRECT);
+}
+
+static int mp2993_read_word_data(struct i2c_client *client, int page, int phase,
+ int reg)
+{
+ int ret;
+
+ switch (reg) {
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ ret = pmbus_read_word_data(client, page, phase, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST(ret * MP2993_VOUT_OVUV_UINT, MP2993_VOUT_OVUV_DIV);
+ break;
+ case PMBUS_OT_FAULT_LIMIT:
+ case PMBUS_OT_WARN_LIMIT:
+ /*
+ * The MP2993 ot fault limit value and ot warn limit value
+ * per rail are always the same, so only PMBUS_OT_FAULT_LIMIT
+ * and PMBUS_OT_WARN_LIMIT register in page 0 are defined to
+ * indicates the limit value.
+ */
+ ret = pmbus_read_word_data(client, 0, phase, reg);
+ break;
+ case PMBUS_READ_VIN:
+ /* The MP2993 vin scale is (1/32V)/Lsb */
+ ret = pmbus_read_word_data(client, page, phase, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST((ret & GENMASK(9, 0)) * MP2993_READ_VIN_UINT,
+ MP2993_READ_VIN_DIV);
+ break;
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ /* The MP2993 vin limit scale is (1/8V)/Lsb */
+ ret = pmbus_read_word_data(client, page, phase, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST((ret & GENMASK(7, 0)) * MP2993_VIN_LIMIT_UINT,
+ MP2993_VIN_LIMIT_DIV);
+ break;
+ case PMBUS_READ_IOUT:
+ case PMBUS_READ_IIN:
+ case PMBUS_IIN_OC_WARN_LIMIT:
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ case PMBUS_READ_VOUT:
+ case PMBUS_READ_PIN:
+ case PMBUS_READ_POUT:
+ case PMBUS_READ_TEMPERATURE_1:
+ ret = -ENODATA;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static int mp2993_write_word_data(struct i2c_client *client, int page, int reg,
+ u16 word)
+{
+ int ret;
+
+ switch (reg) {
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ ret = DIV_ROUND_CLOSEST(word * MP2993_VOUT_OVUV_DIV, MP2993_VOUT_OVUV_UINT);
+ ret = pmbus_write_word_data(client, 0, reg, ret);
+ break;
+ case PMBUS_OT_FAULT_LIMIT:
+ case PMBUS_OT_WARN_LIMIT:
+ /*
+ * The MP2993 ot fault limit value and ot warn limit value
+ * per rail are always the same, so only PMBUS_OT_FAULT_LIMIT
+ * and PMBUS_OT_WARN_LIMIT register in page 0 are defined to
+ * config the ot limit value.
+ */
+ ret = pmbus_write_word_data(client, 0, reg, word);
+ break;
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ /* The MP2993 vin limit scale is (1/8V)/Lsb */
+ ret = pmbus_write_word_data(client, 0, reg,
+ DIV_ROUND_CLOSEST(word * MP2993_VIN_LIMIT_DIV,
+ MP2993_VIN_LIMIT_UINT));
+ break;
+ case PMBUS_IIN_OC_WARN_LIMIT:
+ /*
+ * The PMBUS_IIN_OC_WARN_LIMIT of MP2993 is linear11 format,
+ * and the exponent is a constant value(5'b00000)， so the
+ * exponent of word parameter should be converted to 5'b00000.
+ */
+ ret = pmbus_write_word_data(client, page, reg,
+ mp2993_linear11_exponent_transfer(word, 0x00));
+ break;
+ //
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ /*
+ * The PMBUS_IOUT_OC_FAULT_LIMIT and PMBUS_IOUT_OC_WARN_LIMIT
+ * of MP2993 can be regarded as linear11 format, and the
+ * exponent is a 5'b00001 or 5'b00000. To ensure a larger
+ * range of limit value, so the exponent of word parameter
+ * should be converted to 5'b00001.
+ */
+ ret = pmbus_write_word_data(client, page, reg,
+ mp2993_linear11_exponent_transfer(word, 0x01));
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static struct pmbus_driver_info mp2993_info = {
+ .pages = MP2993_PAGE_NUM,
+ .format[PSC_VOLTAGE_IN] = direct,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_TEMPERATURE] = direct,
+ .format[PSC_POWER] = linear,
+ .format[PSC_VOLTAGE_OUT] = direct,
+
+ .m[PSC_VOLTAGE_OUT] = 1,
+ .R[PSC_VOLTAGE_OUT] = 3,
+ .b[PSC_VOLTAGE_OUT] = 0,
+
+ .m[PSC_VOLTAGE_IN] = 1,
+ .R[PSC_VOLTAGE_IN] = 0,
+ .b[PSC_VOLTAGE_IN] = 0,
+
+ .m[PSC_TEMPERATURE] = 1,
+ .R[PSC_TEMPERATURE] = 0,
+ .b[PSC_TEMPERATURE] = 0,
+
+ .func[0] = MP2993_RAIL1_FUNC,
+ .func[1] = MP2993_RAIL2_FUNC,
+ .read_word_data = mp2993_read_word_data,
+ .write_word_data = mp2993_write_word_data,
+ .identify = mp2993_identify,
+};
+
+static int mp2993_probe(struct i2c_client *client)
+{
+ return pmbus_do_probe(client, &mp2993_info);
+}
+
+static const struct i2c_device_id mp2993_id[] = {
+ {"mp2993", 0},
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, mp2993_id);
+
+static const struct of_device_id __maybe_unused mp2993_of_match[] = {
+ {.compatible = "mps,mp2993"},
+ {}
+};
+MODULE_DEVICE_TABLE(of, mp2993_of_match);
+
+static struct i2c_driver mp2993_driver = {
+ .driver = {
+ .name = "mp2993",
+ .of_match_table = mp2993_of_match,
+ },
+ .probe = mp2993_probe,
+ .id_table = mp2993_id,
+};
+
+module_i2c_driver(mp2993_driver);
+
+MODULE_AUTHOR("Noah Wang <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for MPS MP2993");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PMBUS);
--
2.25.1
On Tue, Jun 11, 2024 at 06:14:15PM +0800, Noah Wang wrote:
> Add support for MPS VR controller mp2993. This driver exposes
> telemetry and limits value readings and writtings.
>
> Signed-off-by: Noah Wang <[email protected]>
Applied.
Thanks,
Guenter