Using only 4 DMA periods for UART RX is very few if we have a high
frequency of small transfers - like in our case using Bluetooth with
many small packets via UART - causing many dma transfers but in each
only filling a fraction of a single buffer. Such a case may lead to
the situation that DMA RX transfer is triggered but no free buffer is
available. When this happens dma channel ist stopped - with the patch
"dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
possible consequences that:
with disabled hw flow control:
If enough data is incoming on UART port the RX FIFO runs over and
characters will be lost. What then happens depends on upper layer.
with enabled hw flow control:
If enough data is incoming on UART port the RX FIFO reaches a level
where CTS is deasserted and remote device sending the data stops.
If it fails to stop timely the i.MX' RX FIFO may run over and data
get lost. Otherwise it's internal TX buffer may getting filled to
a point where it runs over and data is again lost. It depends on
the remote device how this case is handled and if it is recoverable.
Obviously we want to avoid having no free buffers available. So we
decrease the size of the buffers and increase their number and the
total buffer size.
Signed-off-by: Philipp Puschmann <[email protected]>
Reviewed-by: Lucas Stach <[email protected]>
---
Changelog v3:
- enhance description
Changelog v2:
- split this patch from series "Fix UART DMA freezes for iMX6"
- add Reviewed-by tag
drivers/tty/serial/imx.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 87c58f9f6390..51dc19833eab 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct timer_list *t)
}
}
-#define RX_BUF_SIZE (PAGE_SIZE)
-
/*
* There are two kinds of RX DMA interrupts(such as in the MX6Q):
* [1] the RX DMA buffer is full.
@@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void *data)
}
/* RX DMA buffer periods */
-#define RX_DMA_PERIODS 4
+#define RX_DMA_PERIODS 16
+#define RX_BUF_SIZE (PAGE_SIZE / 4)
static int imx_uart_start_rx_dma(struct imx_port *sport)
{
--
2.23.0
From: Philipp Puschmann <[email protected]> Sent: Thursday, September 19, 2019 10:51 PM
> Using only 4 DMA periods for UART RX is very few if we have a high frequency
> of small transfers - like in our case using Bluetooth with many small packets
> via UART - causing many dma transfers but in each only filling a fraction of a
> single buffer. Such a case may lead to the situation that DMA RX transfer is
> triggered but no free buffer is available. When this happens dma channel ist
> stopped - with the patch
> "dmaengine: imx-sdma: fix dma freezes" temporarily only - with the possible
> consequences that:
> with disabled hw flow control:
> If enough data is incoming on UART port the RX FIFO runs over and
> characters will be lost. What then happens depends on upper layer.
>
> with enabled hw flow control:
> If enough data is incoming on UART port the RX FIFO reaches a level
> where CTS is deasserted and remote device sending the data stops.
> If it fails to stop timely the i.MX' RX FIFO may run over and data
> get lost. Otherwise it's internal TX buffer may getting filled to
> a point where it runs over and data is again lost. It depends on
> the remote device how this case is handled and if it is recoverable.
>
> Obviously we want to avoid having no free buffers available. So we decrease
> the size of the buffers and increase their number and the total buffer size.
>
> Signed-off-by: Philipp Puschmann <[email protected]>
> Reviewed-by: Lucas Stach <[email protected]>
> ---
>
> Changelog v3:
> - enhance description
>
> Changelog v2:
> - split this patch from series "Fix UART DMA freezes for iMX6"
> - add Reviewed-by tag
>
> drivers/tty/serial/imx.c | 5 ++---
> 1 file changed, 2 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index
> 87c58f9f6390..51dc19833eab 100644
> --- a/drivers/tty/serial/imx.c
> +++ b/drivers/tty/serial/imx.c
> @@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct timer_list *t)
> }
> }
>
> -#define RX_BUF_SIZE (PAGE_SIZE)
> -
> /*
> * There are two kinds of RX DMA interrupts(such as in the MX6Q):
> * [1] the RX DMA buffer is full.
> @@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void
> *data) }
>
> /* RX DMA buffer periods */
> -#define RX_DMA_PERIODS 4
> +#define RX_DMA_PERIODS 16
> +#define RX_BUF_SIZE (PAGE_SIZE / 4)
>
Why to decrease the DMA RX buffer size here ?
The current DMA implementation support DMA cyclic mode, one SDMA BD receive one Bluetooth frame can
bring better performance.
As you know, for L2CAP, a maximum transmission unit (MTU) associated with the largest Baseband payload
is 341 bytes for DH5 packets.
So I suggest to increase RX_BUF_SIZE along with RX_DMA_PERIODS to feasible value.
Andy
> static int imx_uart_start_rx_dma(struct imx_port *sport) {
> --
> 2.23.0
Hi Andy,
Am 20.09.19 um 05:42 schrieb Andy Duan:
> From: Philipp Puschmann <[email protected]> Sent: Thursday, September 19, 2019 10:51 PM
>> Using only 4 DMA periods for UART RX is very few if we have a high frequency
>> of small transfers - like in our case using Bluetooth with many small packets
>> via UART - causing many dma transfers but in each only filling a fraction of a
>> single buffer. Such a case may lead to the situation that DMA RX transfer is
>> triggered but no free buffer is available. When this happens dma channel ist
>> stopped - with the patch
>> "dmaengine: imx-sdma: fix dma freezes" temporarily only - with the possible
>> consequences that:
>> with disabled hw flow control:
>> If enough data is incoming on UART port the RX FIFO runs over and
>> characters will be lost. What then happens depends on upper layer.
>>
>> with enabled hw flow control:
>> If enough data is incoming on UART port the RX FIFO reaches a level
>> where CTS is deasserted and remote device sending the data stops.
>> If it fails to stop timely the i.MX' RX FIFO may run over and data
>> get lost. Otherwise it's internal TX buffer may getting filled to
>> a point where it runs over and data is again lost. It depends on
>> the remote device how this case is handled and if it is recoverable.
>>
>> Obviously we want to avoid having no free buffers available. So we decrease
>> the size of the buffers and increase their number and the total buffer size.
>>
>> Signed-off-by: Philipp Puschmann <[email protected]>
>> Reviewed-by: Lucas Stach <[email protected]>
>> ---
>>
>> Changelog v3:
>> - enhance description
>>
>> Changelog v2:
>> - split this patch from series "Fix UART DMA freezes for iMX6"
>> - add Reviewed-by tag
>>
>> drivers/tty/serial/imx.c | 5 ++---
>> 1 file changed, 2 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index
>> 87c58f9f6390..51dc19833eab 100644
>> --- a/drivers/tty/serial/imx.c
>> +++ b/drivers/tty/serial/imx.c
>> @@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct timer_list *t)
>> }
>> }
>>
>> -#define RX_BUF_SIZE (PAGE_SIZE)
>> -
>> /*
>> * There are two kinds of RX DMA interrupts(such as in the MX6Q):
>> * [1] the RX DMA buffer is full.
>> @@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void
>> *data) }
>>
>> /* RX DMA buffer periods */
>> -#define RX_DMA_PERIODS 4
>> +#define RX_DMA_PERIODS 16
>> +#define RX_BUF_SIZE (PAGE_SIZE / 4)
>>
> Why to decrease the DMA RX buffer size here ?
>
> The current DMA implementation support DMA cyclic mode, one SDMA BD receive one Bluetooth frame can
> bring better performance.
> As you know, for L2CAP, a maximum transmission unit (MTU) associated with the largest Baseband payload
> is 341 bytes for DH5 packets.
>
> So I suggest to increase RX_BUF_SIZE along with RX_DMA_PERIODS to feasible value.
I debugged and developed this patches on a system with a 4.15 kernel. When prepared for upstream i have adapted
some details and missed a important thing here. It should say:
+#define RX_BUF_SIZE (RX_DMA_PERIODS * PAGE_SIZE / 4)
Yes, i wanted to increase the total buffer size too, even wrote it in the description.
I will prepare a version 4, thanks for the hint.
Just for info: A single RX DMA period aka buffer can be filled with mutliple packets in regard of the upper layer, here BT.
Regards,
Philipp
>
> Andy
>
>> static int imx_uart_start_rx_dma(struct imx_port *sport) {
>> --
>> 2.23.0
>
From: Philipp Puschmann <[email protected]> Sent: Friday, September 20, 2019 3:06 PM
> Am 20.09.19 um 05:42 schrieb Andy Duan:
> > From: Philipp Puschmann <[email protected]> Sent: Thursday,
> > September 19, 2019 10:51 PM
> >> Using only 4 DMA periods for UART RX is very few if we have a high
> >> frequency of small transfers - like in our case using Bluetooth with
> >> many small packets via UART - causing many dma transfers but in each
> >> only filling a fraction of a single buffer. Such a case may lead to
> >> the situation that DMA RX transfer is triggered but no free buffer is
> >> available. When this happens dma channel ist stopped - with the patch
> >> "dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
> >> possible consequences that:
> >> with disabled hw flow control:
> >> If enough data is incoming on UART port the RX FIFO runs over and
> >> characters will be lost. What then happens depends on upper layer.
> >>
> >> with enabled hw flow control:
> >> If enough data is incoming on UART port the RX FIFO reaches a level
> >> where CTS is deasserted and remote device sending the data stops.
> >> If it fails to stop timely the i.MX' RX FIFO may run over and data
> >> get lost. Otherwise it's internal TX buffer may getting filled to
> >> a point where it runs over and data is again lost. It depends on
> >> the remote device how this case is handled and if it is recoverable.
> >>
> >> Obviously we want to avoid having no free buffers available. So we
> >> decrease the size of the buffers and increase their number and the total
> buffer size.
> >>
> >> Signed-off-by: Philipp Puschmann <[email protected]>
> >> Reviewed-by: Lucas Stach <[email protected]>
> >> ---
> >>
> >> Changelog v3:
> >> - enhance description
> >>
> >> Changelog v2:
> >> - split this patch from series "Fix UART DMA freezes for iMX6"
> >> - add Reviewed-by tag
> >>
> >> drivers/tty/serial/imx.c | 5 ++---
> >> 1 file changed, 2 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
> >> index 87c58f9f6390..51dc19833eab 100644
> >> --- a/drivers/tty/serial/imx.c
> >> +++ b/drivers/tty/serial/imx.c
> >> @@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct timer_list
> *t)
> >> }
> >> }
> >>
> >> -#define RX_BUF_SIZE (PAGE_SIZE)
> >> -
> >> /*
> >> * There are two kinds of RX DMA interrupts(such as in the MX6Q):
> >> * [1] the RX DMA buffer is full.
> >> @@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void
> >> *data) }
> >>
> >> /* RX DMA buffer periods */
> >> -#define RX_DMA_PERIODS 4
> >> +#define RX_DMA_PERIODS 16
> >> +#define RX_BUF_SIZE (PAGE_SIZE / 4)
> >>
> > Why to decrease the DMA RX buffer size here ?
> >
> > The current DMA implementation support DMA cyclic mode, one SDMA BD
> > receive one Bluetooth frame can bring better performance.
> > As you know, for L2CAP, a maximum transmission unit (MTU) associated
> > with the largest Baseband payload is 341 bytes for DH5 packets.
> >
> > So I suggest to increase RX_BUF_SIZE along with RX_DMA_PERIODS to
> feasible value.
>
> I debugged and developed this patches on a system with a 4.15 kernel. When
> prepared for upstream i have adapted some details and missed a important
> thing here. It should say:
>
> +#define RX_BUF_SIZE (RX_DMA_PERIODS * PAGE_SIZE / 4)
>
> Yes, i wanted to increase the total buffer size too, even wrote it in the
> description.
> I will prepare a version 4, thanks for the hint.
Okay, thank you for submit the SDMA/uart patch set.
>
> Just for info: A single RX DMA period aka buffer can be filled with mutliple
> packets in regard of the upper layer, here BT.
Yes, that depends on system loading.
>
>
> Regards,
> Philipp
> >
> > Andy
> >
> >> static int imx_uart_start_rx_dma(struct imx_port *sport) {
> >> --
> >> 2.23.0
> >
On Fri, Sep 20, 2019 at 2:06 AM Philipp Puschmann
<[email protected]> wrote:
>
> Hi Andy,
>
> Am 20.09.19 um 05:42 schrieb Andy Duan:
> > From: Philipp Puschmann <[email protected]> Sent: Thursday, September 19, 2019 10:51 PM
> >> Using only 4 DMA periods for UART RX is very few if we have a high frequency
> >> of small transfers - like in our case using Bluetooth with many small packets
> >> via UART - causing many dma transfers but in each only filling a fraction of a
> >> single buffer. Such a case may lead to the situation that DMA RX transfer is
> >> triggered but no free buffer is available. When this happens dma channel ist
> >> stopped - with the patch
> >> "dmaengine: imx-sdma: fix dma freezes" temporarily only - with the possible
> >> consequences that:
I have an i.MX6Q with Wl1837MOD on UART 2 with flow control, and I am
getting Bluetooth transfer timeouts.
(see imx6-logicpd-som.dtsi)
On top of 5.3.1, I have installed:
dmaengine: imx-sdma: fix buffer ownership
dmaengine: imx-sdma: fix dma freezes
dmaengine: imx-sdma: drop redundant variable
dmaengine: imx-sdma: fix kernel hangs with SLUB slab allocator
serial: imx: adapt rx buffer and dma periods
and I still get timeouts:
[ 66.632006] Bluetooth: hci0: command 0xff36 tx timeout
[ 76.790499] Bluetooth: hci0: command 0x1001 tx timeout
[ 87.110488] Bluetooth: hci0: command 0xff36 tx timeout
[ 97.270507] Bluetooth: hci0: command 0x1001 tx timeout
[ 107.590457] Bluetooth: hci0: command 0xff36 tx timeout
[ 117.750477] Bluetooth: hci0: command 0x1001 tx timeout
[ 226.390499] Bluetooth: hci0: command 0xfe38 tx timeout
[ 231.590735] Bluetooth: hci0: command tx timeout
I did a bisect and found the start of my problems came from
361deb7243d2 ("dmaengine: dmatest: wrap src & dst data into a struct")
This happened sometime between v5.0 and v5.1
Is there a patch I missed somewhere? Do I need to change my device
tree configuration somehow to allocate the proper DMA memory?
> >> with disabled hw flow control:
> >> If enough data is incoming on UART port the RX FIFO runs over and
> >> characters will be lost. What then happens depends on upper layer.
> >>
> >> with enabled hw flow control:
> >> If enough data is incoming on UART port the RX FIFO reaches a level
> >> where CTS is deasserted and remote device sending the data stops.
> >> If it fails to stop timely the i.MX' RX FIFO may run over and data
> >> get lost. Otherwise it's internal TX buffer may getting filled to
> >> a point where it runs over and data is again lost. It depends on
> >> the remote device how this case is handled and if it is recoverable.
> >>
> >> Obviously we want to avoid having no free buffers available. So we decrease
> >> the size of the buffers and increase their number and the total buffer size.
> >>
> >> Signed-off-by: Philipp Puschmann <[email protected]>
> >> Reviewed-by: Lucas Stach <[email protected]>
> >> ---
> >>
> >> Changelog v3:
> >> - enhance description
> >>
> >> Changelog v2:
> >> - split this patch from series "Fix UART DMA freezes for iMX6"
> >> - add Reviewed-by tag
> >>
> >> drivers/tty/serial/imx.c | 5 ++---
> >> 1 file changed, 2 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index
> >> 87c58f9f6390..51dc19833eab 100644
> >> --- a/drivers/tty/serial/imx.c
> >> +++ b/drivers/tty/serial/imx.c
> >> @@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct timer_list *t)
> >> }
> >> }
> >>
> >> -#define RX_BUF_SIZE (PAGE_SIZE)
> >> -
> >> /*
> >> * There are two kinds of RX DMA interrupts(such as in the MX6Q):
> >> * [1] the RX DMA buffer is full.
> >> @@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void
> >> *data) }
> >>
> >> /* RX DMA buffer periods */
> >> -#define RX_DMA_PERIODS 4
> >> +#define RX_DMA_PERIODS 16
> >> +#define RX_BUF_SIZE (PAGE_SIZE / 4)
> >>
> > Why to decrease the DMA RX buffer size here ?
> >
> > The current DMA implementation support DMA cyclic mode, one SDMA BD receive one Bluetooth frame can
> > bring better performance.
> > As you know, for L2CAP, a maximum transmission unit (MTU) associated with the largest Baseband payload
> > is 341 bytes for DH5 packets.
> >
> > So I suggest to increase RX_BUF_SIZE along with RX_DMA_PERIODS to feasible value.
>
> I debugged and developed this patches on a system with a 4.15 kernel. When prepared for upstream i have adapted
> some details and missed a important thing here. It should say:
>
> +#define RX_BUF_SIZE (RX_DMA_PERIODS * PAGE_SIZE / 4)
>
> Yes, i wanted to increase the total buffer size too, even wrote it in the description.
> I will prepare a version 4, thanks for the hint.
>
> Just for info: A single RX DMA period aka buffer can be filled with mutliple packets in regard of the upper layer, here BT.
>
>
> Regards,
> Philipp
> >
> > Andy
> >
> >> static int imx_uart_start_rx_dma(struct imx_port *sport) {
> >> --
> >> 2.23.0
> >
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Wed, 2019-09-25 at 10:14 -0500, Adam Ford wrote:
> [External]
>
> On Fri, Sep 20, 2019 at 2:06 AM Philipp Puschmann
> <[email protected]> wrote:
> > Hi Andy,
> >
> > Am 20.09.19 um 05:42 schrieb Andy Duan:
> > > From: Philipp Puschmann <[email protected]> Sent: Thursday,
> > > September 19, 2019 10:51 PM
> > > > Using only 4 DMA periods for UART RX is very few if we have a high
> > > > frequency
> > > > of small transfers - like in our case using Bluetooth with many
> > > > small packets
> > > > via UART - causing many dma transfers but in each only filling a
> > > > fraction of a
> > > > single buffer. Such a case may lead to the situation that DMA RX
> > > > transfer is
> > > > triggered but no free buffer is available. When this happens dma
> > > > channel ist
> > > > stopped - with the patch
> > > > "dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
> > > > possible
> > > > consequences that:
>
> I have an i.MX6Q with Wl1837MOD on UART 2 with flow control, and I am
> getting Bluetooth transfer timeouts.
> (see imx6-logicpd-som.dtsi)
>
> On top of 5.3.1, I have installed:
>
> dmaengine: imx-sdma: fix buffer ownership
> dmaengine: imx-sdma: fix dma freezes
> dmaengine: imx-sdma: drop redundant variable
> dmaengine: imx-sdma: fix kernel hangs with SLUB slab allocator
> serial: imx: adapt rx buffer and dma periods
>
> and I still get timeouts:
>
> [ 66.632006] Bluetooth: hci0: command 0xff36 tx timeout
> [ 76.790499] Bluetooth: hci0: command 0x1001 tx timeout
> [ 87.110488] Bluetooth: hci0: command 0xff36 tx timeout
> [ 97.270507] Bluetooth: hci0: command 0x1001 tx timeout
> [ 107.590457] Bluetooth: hci0: command 0xff36 tx timeout
> [ 117.750477] Bluetooth: hci0: command 0x1001 tx timeout
> [ 226.390499] Bluetooth: hci0: command 0xfe38 tx timeout
> [ 231.590735] Bluetooth: hci0: command tx timeout
>
> I did a bisect and found the start of my problems came from
>
> 361deb7243d2 ("dmaengine: dmatest: wrap src & dst data into a struct")
That commit only touches `drivers/dma/dmatest.c`
Are you using that module?
It's a "unit-test" module for testing DMAengine drivers.
The only way that can break anything [from what I can tell], is if it is
being run. It will probably put the DMA into a weird state (it is a test-
module after-all), and it may require some DMAs to be reset.
I admit it would be nice that the test-module would put the DMA back into a
normal-working state, but that effort could be big for some cases.
>
> This happened sometime between v5.0 and v5.1
>
> Is there a patch I missed somewhere? Do I need to change my device
> tree configuration somehow to allocate the proper DMA memory?
>
>
>
> > > > with disabled hw flow control:
> > > > If enough data is incoming on UART port the RX FIFO runs over and
> > > > characters will be lost. What then happens depends on upper
> > > > layer.
> > > >
> > > > with enabled hw flow control:
> > > > If enough data is incoming on UART port the RX FIFO reaches a
> > > > level
> > > > where CTS is deasserted and remote device sending the data stops.
> > > > If it fails to stop timely the i.MX' RX FIFO may run over and
> > > > data
> > > > get lost. Otherwise it's internal TX buffer may getting filled to
> > > > a point where it runs over and data is again lost. It depends on
> > > > the remote device how this case is handled and if it is
> > > > recoverable.
> > > >
> > > > Obviously we want to avoid having no free buffers available. So we
> > > > decrease
> > > > the size of the buffers and increase their number and the total
> > > > buffer size.
> > > >
> > > > Signed-off-by: Philipp Puschmann <[email protected]>
> > > > Reviewed-by: Lucas Stach <[email protected]>
> > > > ---
> > > >
> > > > Changelog v3:
> > > > - enhance description
> > > >
> > > > Changelog v2:
> > > > - split this patch from series "Fix UART DMA freezes for iMX6"
> > > > - add Reviewed-by tag
> > > >
> > > > drivers/tty/serial/imx.c | 5 ++---
> > > > 1 file changed, 2 insertions(+), 3 deletions(-)
> > > >
> > > > diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
> > > > index
> > > > 87c58f9f6390..51dc19833eab 100644
> > > > --- a/drivers/tty/serial/imx.c
> > > > +++ b/drivers/tty/serial/imx.c
> > > > @@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct
> > > > timer_list *t)
> > > > }
> > > > }
> > > >
> > > > -#define RX_BUF_SIZE (PAGE_SIZE)
> > > > -
> > > > /*
> > > > * There are two kinds of RX DMA interrupts(such as in the MX6Q):
> > > > * [1] the RX DMA buffer is full.
> > > > @@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void
> > > > *data) }
> > > >
> > > > /* RX DMA buffer periods */
> > > > -#define RX_DMA_PERIODS 4
> > > > +#define RX_DMA_PERIODS 16
> > > > +#define RX_BUF_SIZE (PAGE_SIZE / 4)
> > > >
> > > Why to decrease the DMA RX buffer size here ?
> > >
> > > The current DMA implementation support DMA cyclic mode, one SDMA BD
> > > receive one Bluetooth frame can
> > > bring better performance.
> > > As you know, for L2CAP, a maximum transmission unit (MTU) associated
> > > with the largest Baseband payload
> > > is 341 bytes for DH5 packets.
> > >
> > > So I suggest to increase RX_BUF_SIZE along with RX_DMA_PERIODS to
> > > feasible value.
> >
> > I debugged and developed this patches on a system with a 4.15 kernel.
> > When prepared for upstream i have adapted
> > some details and missed a important thing here. It should say:
> >
> > +#define RX_BUF_SIZE (RX_DMA_PERIODS * PAGE_SIZE / 4)
> >
> > Yes, i wanted to increase the total buffer size too, even wrote it in
> > the description.
> > I will prepare a version 4, thanks for the hint.
> >
> > Just for info: A single RX DMA period aka buffer can be filled with
> > mutliple packets in regard of the upper layer, here BT.
> >
> >
> > Regards,
> > Philipp
> > > Andy
> > >
> > > > static int imx_uart_start_rx_dma(struct imx_port *sport) {
> > > > --
> > > > 2.23.0
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > [email protected]
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Thu, Sep 26, 2019 at 1:37 AM Ardelean, Alexandru
<[email protected]> wrote:
>
> On Wed, 2019-09-25 at 10:14 -0500, Adam Ford wrote:
> > [External]
> >
> > On Fri, Sep 20, 2019 at 2:06 AM Philipp Puschmann
> > <[email protected]> wrote:
> > > Hi Andy,
> > >
> > > Am 20.09.19 um 05:42 schrieb Andy Duan:
> > > > From: Philipp Puschmann <[email protected]> Sent: Thursday,
> > > > September 19, 2019 10:51 PM
> > > > > Using only 4 DMA periods for UART RX is very few if we have a high
> > > > > frequency
> > > > > of small transfers - like in our case using Bluetooth with many
> > > > > small packets
> > > > > via UART - causing many dma transfers but in each only filling a
> > > > > fraction of a
> > > > > single buffer. Such a case may lead to the situation that DMA RX
> > > > > transfer is
> > > > > triggered but no free buffer is available. When this happens dma
> > > > > channel ist
> > > > > stopped - with the patch
> > > > > "dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
> > > > > possible
> > > > > consequences that:
> >
> > I have an i.MX6Q with Wl1837MOD on UART 2 with flow control, and I am
> > getting Bluetooth transfer timeouts.
> > (see imx6-logicpd-som.dtsi)
> >
> > On top of 5.3.1, I have installed:
> >
> > dmaengine: imx-sdma: fix buffer ownership
> > dmaengine: imx-sdma: fix dma freezes
> > dmaengine: imx-sdma: drop redundant variable
> > dmaengine: imx-sdma: fix kernel hangs with SLUB slab allocator
> > serial: imx: adapt rx buffer and dma periods
> >
> > and I still get timeouts:
> >
> > [ 66.632006] Bluetooth: hci0: command 0xff36 tx timeout
> > [ 76.790499] Bluetooth: hci0: command 0x1001 tx timeout
> > [ 87.110488] Bluetooth: hci0: command 0xff36 tx timeout
> > [ 97.270507] Bluetooth: hci0: command 0x1001 tx timeout
> > [ 107.590457] Bluetooth: hci0: command 0xff36 tx timeout
> > [ 117.750477] Bluetooth: hci0: command 0x1001 tx timeout
> > [ 226.390499] Bluetooth: hci0: command 0xfe38 tx timeout
> > [ 231.590735] Bluetooth: hci0: command tx timeout
> >
> > I did a bisect and found the start of my problems came from
> >
> > 361deb7243d2 ("dmaengine: dmatest: wrap src & dst data into a struct")
>
> That commit only touches `drivers/dma/dmatest.c`
> Are you using that module?
>
> It's a "unit-test" module for testing DMAengine drivers.
> The only way that can break anything [from what I can tell], is if it is
> being run. It will probably put the DMA into a weird state (it is a test-
> module after-all), and it may require some DMAs to be reset.
> I admit it would be nice that the test-module would put the DMA back into a
> normal-working state, but that effort could be big for some cases.
I will bisect it again. I removed the CONFIG_DMATEST from the
omx_v6_v7_defconfig, and I still got the failure using Kernel 5.3.1,
so I'll work on this tomorrow and try to narrow it down better with
and without the test module installed.
adam
>
>
> >
> > This happened sometime between v5.0 and v5.1
> >
> > Is there a patch I missed somewhere? Do I need to change my device
> > tree configuration somehow to allocate the proper DMA memory?
> >
> >
> >
> > > > > with disabled hw flow control:
> > > > > If enough data is incoming on UART port the RX FIFO runs over and
> > > > > characters will be lost. What then happens depends on upper
> > > > > layer.
> > > > >
> > > > > with enabled hw flow control:
> > > > > If enough data is incoming on UART port the RX FIFO reaches a
> > > > > level
> > > > > where CTS is deasserted and remote device sending the data stops.
> > > > > If it fails to stop timely the i.MX' RX FIFO may run over and
> > > > > data
> > > > > get lost. Otherwise it's internal TX buffer may getting filled to
> > > > > a point where it runs over and data is again lost. It depends on
> > > > > the remote device how this case is handled and if it is
> > > > > recoverable.
> > > > >
> > > > > Obviously we want to avoid having no free buffers available. So we
> > > > > decrease
> > > > > the size of the buffers and increase their number and the total
> > > > > buffer size.
> > > > >
> > > > > Signed-off-by: Philipp Puschmann <[email protected]>
> > > > > Reviewed-by: Lucas Stach <[email protected]>
> > > > > ---
> > > > >
> > > > > Changelog v3:
> > > > > - enhance description
> > > > >
> > > > > Changelog v2:
> > > > > - split this patch from series "Fix UART DMA freezes for iMX6"
> > > > > - add Reviewed-by tag
> > > > >
> > > > > drivers/tty/serial/imx.c | 5 ++---
> > > > > 1 file changed, 2 insertions(+), 3 deletions(-)
> > > > >
> > > > > diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
> > > > > index
> > > > > 87c58f9f6390..51dc19833eab 100644
> > > > > --- a/drivers/tty/serial/imx.c
> > > > > +++ b/drivers/tty/serial/imx.c
> > > > > @@ -1034,8 +1034,6 @@ static void imx_uart_timeout(struct
> > > > > timer_list *t)
> > > > > }
> > > > > }
> > > > >
> > > > > -#define RX_BUF_SIZE (PAGE_SIZE)
> > > > > -
> > > > > /*
> > > > > * There are two kinds of RX DMA interrupts(such as in the MX6Q):
> > > > > * [1] the RX DMA buffer is full.
> > > > > @@ -1118,7 +1116,8 @@ static void imx_uart_dma_rx_callback(void
> > > > > *data) }
> > > > >
> > > > > /* RX DMA buffer periods */
> > > > > -#define RX_DMA_PERIODS 4
> > > > > +#define RX_DMA_PERIODS 16
> > > > > +#define RX_BUF_SIZE (PAGE_SIZE / 4)
> > > > >
> > > > Why to decrease the DMA RX buffer size here ?
> > > >
> > > > The current DMA implementation support DMA cyclic mode, one SDMA BD
> > > > receive one Bluetooth frame can
> > > > bring better performance.
> > > > As you know, for L2CAP, a maximum transmission unit (MTU) associated
> > > > with the largest Baseband payload
> > > > is 341 bytes for DH5 packets.
> > > >
> > > > So I suggest to increase RX_BUF_SIZE along with RX_DMA_PERIODS to
> > > > feasible value.
> > >
> > > I debugged and developed this patches on a system with a 4.15 kernel.
> > > When prepared for upstream i have adapted
> > > some details and missed a important thing here. It should say:
> > >
> > > +#define RX_BUF_SIZE (RX_DMA_PERIODS * PAGE_SIZE / 4)
> > >
> > > Yes, i wanted to increase the total buffer size too, even wrote it in
> > > the description.
> > > I will prepare a version 4, thanks for the hint.
> > >
> > > Just for info: A single RX DMA period aka buffer can be filled with
> > > mutliple packets in regard of the upper layer, here BT.
> > >
> > >
> > > Regards,
> > > Philipp
> > > > Andy
> > > >
> > > > > static int imx_uart_start_rx_dma(struct imx_port *sport) {
> > > > > --
> > > > > 2.23.0
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > [email protected]
> > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel