From: Conor Dooley <[email protected]>
Add a driver that supports the Microchip FPGA "soft" PWM IP core.
Signed-off-by: Conor Dooley <[email protected]>
---
drivers/pwm/Kconfig | 10 +
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-microchip-core.c | 436 +++++++++++++++++++++++++++++++
3 files changed, 447 insertions(+)
create mode 100644 drivers/pwm/pwm-microchip-core.c
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index dae023d783a2..f42756a014ed 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -393,6 +393,16 @@ config PWM_MEDIATEK
To compile this driver as a module, choose M here: the module
will be called pwm-mediatek.
+config PWM_MICROCHIP_CORE
+ tristate "Microchip corePWM PWM support"
+ depends on SOC_MICROCHIP_POLARFIRE || COMPILE_TEST
+ depends on HAS_IOMEM && OF
+ help
+ PWM driver for Microchip FPGA soft IP core.
+
+ To compile this driver as a module, choose M here: the module
+ will be called pwm-microchip-core.
+
config PWM_MXS
tristate "Freescale MXS PWM support"
depends on ARCH_MXS || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 7bf1a29f02b8..a65625359ece 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_PWM_LPSS_PCI) += pwm-lpss-pci.o
obj-$(CONFIG_PWM_LPSS_PLATFORM) += pwm-lpss-platform.o
obj-$(CONFIG_PWM_MESON) += pwm-meson.o
obj-$(CONFIG_PWM_MEDIATEK) += pwm-mediatek.o
+obj-$(CONFIG_PWM_MICROCHIP_CORE) += pwm-microchip-core.o
obj-$(CONFIG_PWM_MTK_DISP) += pwm-mtk-disp.o
obj-$(CONFIG_PWM_MXS) += pwm-mxs.o
obj-$(CONFIG_PWM_NTXEC) += pwm-ntxec.o
diff --git a/drivers/pwm/pwm-microchip-core.c b/drivers/pwm/pwm-microchip-core.c
new file mode 100644
index 000000000000..047fa708b9fc
--- /dev/null
+++ b/drivers/pwm/pwm-microchip-core.c
@@ -0,0 +1,436 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * corePWM driver for Microchip "soft" FPGA IP cores.
+ *
+ * Copyright (c) 2021-2022 Microchip Corporation. All rights reserved.
+ * Author: Conor Dooley <[email protected]>
+ * Documentation:
+ * https://www.microsemi.com/document-portal/doc_download/1245275-corepwm-hb
+ *
+ * Limitations:
+ * - If the IP block is configured without "shadow registers", all register
+ * writes will take effect immediately, causing glitches on the output.
+ * If shadow registers *are* enabled, a write to the "SYNC_UPDATE" register
+ * notifies the core that it needs to update the registers defining the
+ * waveform from the contents of the "shadow registers".
+ * - The IP block has no concept of a duty cycle, only rising/falling edges of
+ * the waveform. Unfortunately, if the rising & falling edges registers have
+ * the same value written to them the IP block will do whichever of a rising
+ * or a falling edge is possible. I.E. a 50% waveform at twice the requested
+ * period. Therefore to get a 0% waveform, the output is set the max high/low
+ * time depending on polarity.
+ * - The PWM period is set for the whole IP block not per channel. The driver
+ * will only change the period if no other PWM output is enabled.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/ktime.h>
+#include <linux/math.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+
+#define PREG_TO_VAL(PREG) ((PREG) + 1)
+
+#define MCHPCOREPWM_PRESCALE_MAX 0x100
+#define MCHPCOREPWM_PERIOD_STEPS_MAX 0xff
+#define MCHPCOREPWM_PERIOD_MAX 0xff00
+
+#define MCHPCOREPWM_PRESCALE 0x00
+#define MCHPCOREPWM_PERIOD 0x04
+#define MCHPCOREPWM_EN(i) (0x08 + 0x04 * (i)) /* 0x08, 0x0c */
+#define MCHPCOREPWM_POSEDGE(i) (0x10 + 0x08 * (i)) /* 0x10, 0x18, ..., 0x88 */
+#define MCHPCOREPWM_NEGEDGE(i) (0x14 + 0x08 * (i)) /* 0x14, 0x1c, ..., 0x8c */
+#define MCHPCOREPWM_SYNC_UPD 0xe4
+#define MCHPCOREPWM_TIMEOUT_MS 100u
+
+struct mchp_core_pwm_chip {
+ struct pwm_chip chip;
+ struct clk *clk;
+ void __iomem *base;
+ struct mutex lock; /* protect the shared period */
+ ktime_t update_timestamp;
+ u32 sync_update_mask;
+ u16 channel_enabled;
+};
+
+static inline struct mchp_core_pwm_chip *to_mchp_core_pwm(struct pwm_chip *chip)
+{
+ return container_of(chip, struct mchp_core_pwm_chip, chip);
+}
+
+static void mchp_core_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm,
+ bool enable, u64 period)
+{
+ struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
+ u8 channel_enable, reg_offset, shift;
+
+ /*
+ * There are two adjacent 8 bit control regs, the lower reg controls
+ * 0-7 and the upper reg 8-15. Check if the pwm is in the upper reg
+ * and if so, offset by the bus width.
+ */
+ reg_offset = MCHPCOREPWM_EN(pwm->hwpwm >> 3);
+ shift = pwm->hwpwm & 7;
+
+ channel_enable = readb_relaxed(mchp_core_pwm->base + reg_offset);
+ channel_enable &= ~(1 << shift);
+ channel_enable |= (enable << shift);
+
+ writel_relaxed(channel_enable, mchp_core_pwm->base + reg_offset);
+ mchp_core_pwm->channel_enabled &= ~BIT(pwm->hwpwm);
+ mchp_core_pwm->channel_enabled |= enable << pwm->hwpwm;
+
+ /*
+ * Notify the block to update the waveform from the shadow registers.
+ * The updated values will not appear on the bus until they have been
+ * applied to the waveform at the beginning of the next period.
+ * This is a NO-OP if the channel does not have shadow registers.
+ */
+ if (mchp_core_pwm->sync_update_mask & (1 << pwm->hwpwm))
+ mchp_core_pwm->update_timestamp = ktime_add_ns(ktime_get(), period);
+}
+
+static void mchp_core_pwm_wait_for_sync_update(struct mchp_core_pwm_chip *mchp_core_pwm,
+ unsigned int channel)
+{
+ /*
+ * If a shadow register is used for this PWM channel, and iff there is
+ * a pending update to the waveform, we must wait for it to be applied
+ * before attempting to read its state. Reading the registers yields
+ * the currently implemented settings & the new ones are only readable
+ * once the current period has ended.
+ */
+
+ if (mchp_core_pwm->sync_update_mask & (1 << channel)) {
+ ktime_t current_time = ktime_get();
+ s64 remaining_ns;
+ u32 delay_us;
+
+ remaining_ns = ktime_to_ns(ktime_sub(mchp_core_pwm->update_timestamp,
+ current_time));
+
+ /*
+ * If the update has gone through, don't bother waiting for
+ * obvious reasons. Otherwise wait around for an appropriate
+ * amount of time for the update to go through.
+ */
+ if (remaining_ns <= 0)
+ return;
+
+ delay_us = DIV_ROUND_UP_ULL(remaining_ns, NSEC_PER_USEC);
+ if ((delay_us / 1000) > MAX_UDELAY_MS)
+ msleep(delay_us / 1000 + 1);
+ else
+ usleep_range(delay_us, delay_us * 2);
+ }
+}
+
+static u64 mchp_core_pwm_calc_duty(const struct pwm_state *state, u64 clk_rate,
+ u8 prescale, u8 period_steps)
+{
+ u64 duty_steps, tmp;
+ u16 prescale_val = PREG_TO_VAL(prescale);
+
+ /*
+ * Calculate the duty cycle in multiples of the prescaled period:
+ * duty_steps = duty_in_ns / step_in_ns
+ * step_in_ns = (prescale * NSEC_PER_SEC) / clk_rate
+ * The code below is rearranged slightly to only divide once.
+ */
+ tmp = prescale_val * NSEC_PER_SEC;
+ duty_steps = mul_u64_u64_div_u64(state->duty_cycle, clk_rate, tmp);
+
+ return duty_steps;
+}
+
+static void mchp_core_pwm_apply_duty(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state, u64 duty_steps,
+ u8 period_steps)
+{
+ struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
+ u8 posedge, negedge;
+ u8 period_steps_val = PREG_TO_VAL(period_steps);
+
+ /*
+ * Setting posedge == negedge doesn't yield a constant output,
+ * so that's an unsuitable setting to model duty_steps = 0.
+ * In that case set the unwanted edge to a value that never
+ * triggers.
+ */
+ if (state->polarity == PWM_POLARITY_INVERSED) {
+ negedge = !duty_steps ? period_steps_val : 0u;
+ posedge = duty_steps;
+ } else {
+ posedge = !duty_steps ? period_steps_val : 0u;
+ negedge = duty_steps;
+ }
+
+ writel_relaxed(posedge, mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
+ writel_relaxed(negedge, mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
+}
+
+static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
+ u16 *prescale, u8 *period_steps)
+{
+ u64 tmp;
+
+ /*
+ * Calculate the period cycles and prescale values.
+ * The registers are each 8 bits wide & multiplied to compute the period
+ * using the formula:
+ * (clock_period) * (prescale + 1) * (period_steps + 1)
+ * so the maximum period that can be generated is 0x10000 times the
+ * period of the input clock.
+ * However, due to the design of the "hardware", it is not possible to
+ * attain a 100% duty cycle if the full range of period_steps is used.
+ * Therefore period_steps is restricted to 0xFE and the maximum multiple
+ * of the clock period attainable is 0xFF00.
+ */
+ tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
+
+ /*
+ * The hardware adds one to the register value, so decrement by one to
+ * account for the offset
+ */
+ if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
+ *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
+ *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
+
+ return;
+ }
+
+ *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
+ /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
+ *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
+}
+
+static inline void mchp_core_pwm_apply_period(struct mchp_core_pwm_chip *mchp_core_pwm,
+ u8 prescale, u8 period_steps)
+{
+ writel_relaxed(prescale, mchp_core_pwm->base + MCHPCOREPWM_PRESCALE);
+ writel_relaxed(period_steps, mchp_core_pwm->base + MCHPCOREPWM_PERIOD);
+}
+
+static int mchp_core_pwm_apply_locked(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
+ bool period_locked;
+ unsigned long clk_rate;
+ u64 duty_steps;
+ u16 prescale;
+ u8 period_steps;
+
+ if (!state->enabled) {
+ mchp_core_pwm_enable(chip, pwm, false, pwm->state.period);
+ return 0;
+ }
+
+ /*
+ * If clk_rate is too big, the following multiplication might overflow.
+ * However this is implausible, as the fabric of current FPGAs cannot
+ * provide clocks at a rate high enough.
+ */
+ clk_rate = clk_get_rate(mchp_core_pwm->clk);
+ if (clk_rate >= NSEC_PER_SEC)
+ return -EINVAL;
+
+ mchp_core_pwm_calc_period(state, clk_rate, &prescale, &period_steps);
+
+ /*
+ * If the only thing that has changed is the duty cycle or the polarity,
+ * we can shortcut the calculations and just compute/apply the new duty
+ * cycle pos & neg edges
+ * As all the channels share the same period, do not allow it to be
+ * changed if any other channels are enabled.
+ * If the period is locked, it may not be possible to use a period
+ * less than that requested. In that case, we just abort.
+ */
+ period_locked = mchp_core_pwm->channel_enabled & ~(1 << pwm->hwpwm);
+
+ if (period_locked) {
+ u16 hw_prescale;
+ u8 hw_period_steps;
+
+ hw_prescale = readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_PRESCALE);
+ hw_period_steps = readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_PERIOD);
+
+ if ((period_steps + 1) * (prescale + 1) <
+ (hw_period_steps + 1) * (hw_prescale + 1))
+ return -EINVAL;
+
+ /*
+ * It is possible that something could have set the period_steps
+ * register to 0xff, which would prevent us from setting a 100%
+ * or 0% relative duty cycle, as explained above in
+ * mchp_core_pwm_calc_period().
+ * The period is locked and we cannot change this, so we abort.
+ */
+ if (hw_period_steps == MCHPCOREPWM_PERIOD_STEPS_MAX)
+ return -EINVAL;
+
+ prescale = hw_prescale;
+ period_steps = hw_period_steps;
+ } else {
+ mchp_core_pwm_apply_period(mchp_core_pwm, prescale, period_steps);
+ }
+
+ duty_steps = mchp_core_pwm_calc_duty(state, clk_rate, prescale, period_steps);
+
+ /*
+ * Because the period is per channel, it is possible that the requested
+ * duty cycle is longer than the period, in which case cap it to the
+ * period, IOW a 100% duty cycle.
+ */
+ if (duty_steps > period_steps)
+ duty_steps = period_steps + 1;
+
+ mchp_core_pwm_apply_duty(chip, pwm, state, duty_steps, period_steps);
+
+ mchp_core_pwm_enable(chip, pwm, true, pwm->state.period);
+
+ return 0;
+}
+
+static int mchp_core_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
+ int ret;
+
+ mutex_lock(&mchp_core_pwm->lock);
+
+ mchp_core_pwm_wait_for_sync_update(mchp_core_pwm, pwm->hwpwm);
+
+ ret = mchp_core_pwm_apply_locked(chip, pwm, state);
+
+ mutex_unlock(&mchp_core_pwm->lock);
+
+ return ret;
+}
+
+static int mchp_core_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
+ u64 rate;
+ u16 prescale;
+ u8 period_steps, duty_steps, posedge, negedge;
+
+ mutex_lock(&mchp_core_pwm->lock);
+
+ mchp_core_pwm_wait_for_sync_update(mchp_core_pwm, pwm->hwpwm);
+
+ if (mchp_core_pwm->channel_enabled & (1 << pwm->hwpwm))
+ state->enabled = true;
+ else
+ state->enabled = false;
+
+ rate = clk_get_rate(mchp_core_pwm->clk);
+
+ prescale = PREG_TO_VAL(readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_PRESCALE));
+
+ period_steps = PREG_TO_VAL(readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_PERIOD));
+ state->period = period_steps * prescale;
+ state->period *= NSEC_PER_SEC;
+ state->period = DIV64_U64_ROUND_UP(state->period, rate);
+
+ posedge = readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
+ negedge = readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
+
+ mutex_unlock(&mchp_core_pwm->lock);
+
+ if (negedge == posedge) {
+ state->duty_cycle = state->period;
+ state->period *= 2;
+ } else {
+ duty_steps = abs((s16)posedge - (s16)negedge);
+ state->duty_cycle = duty_steps * prescale * NSEC_PER_SEC;
+ state->duty_cycle = DIV64_U64_ROUND_UP(state->duty_cycle, rate);
+ }
+
+ state->polarity = negedge < posedge ? PWM_POLARITY_INVERSED : PWM_POLARITY_NORMAL;
+
+ return 0;
+}
+
+static const struct pwm_ops mchp_core_pwm_ops = {
+ .apply = mchp_core_pwm_apply,
+ .get_state = mchp_core_pwm_get_state,
+ .owner = THIS_MODULE,
+};
+
+static const struct of_device_id mchp_core_of_match[] = {
+ {
+ .compatible = "microchip,corepwm-rtl-v4",
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mchp_core_of_match);
+
+static int mchp_core_pwm_probe(struct platform_device *pdev)
+{
+ struct mchp_core_pwm_chip *mchp_core_pwm;
+ struct resource *regs;
+ int ret;
+
+ mchp_core_pwm = devm_kzalloc(&pdev->dev, sizeof(*mchp_core_pwm), GFP_KERNEL);
+ if (!mchp_core_pwm)
+ return -ENOMEM;
+
+ mchp_core_pwm->base = devm_platform_get_and_ioremap_resource(pdev, 0, ®s);
+ if (IS_ERR(mchp_core_pwm->base))
+ return PTR_ERR(mchp_core_pwm->base);
+
+ mchp_core_pwm->clk = devm_clk_get_enabled(&pdev->dev, NULL);
+ if (IS_ERR(mchp_core_pwm->clk))
+ return dev_err_probe(&pdev->dev, PTR_ERR(mchp_core_pwm->clk),
+ "failed to get PWM clock\n");
+
+ if (of_property_read_u32(pdev->dev.of_node, "microchip,sync-update-mask",
+ &mchp_core_pwm->sync_update_mask))
+ mchp_core_pwm->sync_update_mask = 0;
+
+ mutex_init(&mchp_core_pwm->lock);
+
+ mchp_core_pwm->chip.dev = &pdev->dev;
+ mchp_core_pwm->chip.ops = &mchp_core_pwm_ops;
+ mchp_core_pwm->chip.npwm = 16;
+
+ mchp_core_pwm->channel_enabled = readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_EN(0));
+ mchp_core_pwm->channel_enabled |=
+ readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_EN(1)) << 8;
+
+ ret = devm_pwmchip_add(&pdev->dev, &mchp_core_pwm->chip);
+ if (ret < 0)
+ return dev_err_probe(&pdev->dev, ret, "failed to add PWM chip\n");
+
+ /*
+ * Enabled synchronous update for channels with shadow registers
+ * enabled. For channels without shadow registers, this has no effect
+ * at all so is unconditionally enabled.
+ */
+ writel_relaxed(1U, mchp_core_pwm->base + MCHPCOREPWM_SYNC_UPD);
+ mchp_core_pwm->update_timestamp = ktime_get();
+
+ return 0;
+}
+
+static struct platform_driver mchp_core_pwm_driver = {
+ .driver = {
+ .name = "mchp-core-pwm",
+ .of_match_table = mchp_core_of_match,
+ },
+ .probe = mchp_core_pwm_probe,
+};
+module_platform_driver(mchp_core_pwm_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Conor Dooley <[email protected]>");
+MODULE_DESCRIPTION("corePWM driver for Microchip FPGAs");
--
2.38.1
Hello Conor,
On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> From: Conor Dooley <[email protected]>
>
> Add a driver that supports the Microchip FPGA "soft" PWM IP core.
>
> Signed-off-by: Conor Dooley <[email protected]>
> ---
> drivers/pwm/Kconfig | 10 +
> drivers/pwm/Makefile | 1 +
> drivers/pwm/pwm-microchip-core.c | 436 +++++++++++++++++++++++++++++++
> 3 files changed, 447 insertions(+)
> create mode 100644 drivers/pwm/pwm-microchip-core.c
>
> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> index dae023d783a2..f42756a014ed 100644
> --- a/drivers/pwm/Kconfig
> +++ b/drivers/pwm/Kconfig
> @@ -393,6 +393,16 @@ config PWM_MEDIATEK
> To compile this driver as a module, choose M here: the module
> will be called pwm-mediatek.
>
> +config PWM_MICROCHIP_CORE
> + tristate "Microchip corePWM PWM support"
> + depends on SOC_MICROCHIP_POLARFIRE || COMPILE_TEST
> + depends on HAS_IOMEM && OF
> + help
> + PWM driver for Microchip FPGA soft IP core.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called pwm-microchip-core.
> +
> config PWM_MXS
> tristate "Freescale MXS PWM support"
> depends on ARCH_MXS || COMPILE_TEST
> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> index 7bf1a29f02b8..a65625359ece 100644
> --- a/drivers/pwm/Makefile
> +++ b/drivers/pwm/Makefile
> @@ -34,6 +34,7 @@ obj-$(CONFIG_PWM_LPSS_PCI) += pwm-lpss-pci.o
> obj-$(CONFIG_PWM_LPSS_PLATFORM) += pwm-lpss-platform.o
> obj-$(CONFIG_PWM_MESON) += pwm-meson.o
> obj-$(CONFIG_PWM_MEDIATEK) += pwm-mediatek.o
> +obj-$(CONFIG_PWM_MICROCHIP_CORE) += pwm-microchip-core.o
> obj-$(CONFIG_PWM_MTK_DISP) += pwm-mtk-disp.o
> obj-$(CONFIG_PWM_MXS) += pwm-mxs.o
> obj-$(CONFIG_PWM_NTXEC) += pwm-ntxec.o
> diff --git a/drivers/pwm/pwm-microchip-core.c b/drivers/pwm/pwm-microchip-core.c
> new file mode 100644
> index 000000000000..047fa708b9fc
> --- /dev/null
> +++ b/drivers/pwm/pwm-microchip-core.c
> @@ -0,0 +1,436 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * corePWM driver for Microchip "soft" FPGA IP cores.
> + *
> + * Copyright (c) 2021-2022 Microchip Corporation. All rights reserved.
> + * Author: Conor Dooley <[email protected]>
> + * Documentation:
> + * https://www.microsemi.com/document-portal/doc_download/1245275-corepwm-hb
> + *
> + * Limitations:
> + * - If the IP block is configured without "shadow registers", all register
> + * writes will take effect immediately, causing glitches on the output.
> + * If shadow registers *are* enabled, a write to the "SYNC_UPDATE" register
> + * notifies the core that it needs to update the registers defining the
> + * waveform from the contents of the "shadow registers".
> + * - The IP block has no concept of a duty cycle, only rising/falling edges of
> + * the waveform. Unfortunately, if the rising & falling edges registers have
> + * the same value written to them the IP block will do whichever of a rising
> + * or a falling edge is possible. I.E. a 50% waveform at twice the requested
> + * period. Therefore to get a 0% waveform, the output is set the max high/low
> + * time depending on polarity.
> + * - The PWM period is set for the whole IP block not per channel. The driver
> + * will only change the period if no other PWM output is enabled.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/ktime.h>
> +#include <linux/math.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/pwm.h>
> +
> +#define PREG_TO_VAL(PREG) ((PREG) + 1)
> +
> +#define MCHPCOREPWM_PRESCALE_MAX 0x100
> +#define MCHPCOREPWM_PERIOD_STEPS_MAX 0xff
> +#define MCHPCOREPWM_PERIOD_MAX 0xff00
> +
> +#define MCHPCOREPWM_PRESCALE 0x00
> +#define MCHPCOREPWM_PERIOD 0x04
> +#define MCHPCOREPWM_EN(i) (0x08 + 0x04 * (i)) /* 0x08, 0x0c */
> +#define MCHPCOREPWM_POSEDGE(i) (0x10 + 0x08 * (i)) /* 0x10, 0x18, ..., 0x88 */
> +#define MCHPCOREPWM_NEGEDGE(i) (0x14 + 0x08 * (i)) /* 0x14, 0x1c, ..., 0x8c */
> +#define MCHPCOREPWM_SYNC_UPD 0xe4
> +#define MCHPCOREPWM_TIMEOUT_MS 100u
> +
> +struct mchp_core_pwm_chip {
> + struct pwm_chip chip;
> + struct clk *clk;
> + void __iomem *base;
> + struct mutex lock; /* protect the shared period */
> + ktime_t update_timestamp;
> + u32 sync_update_mask;
> + u16 channel_enabled;
> +};
> +
> +static inline struct mchp_core_pwm_chip *to_mchp_core_pwm(struct pwm_chip *chip)
> +{
> + return container_of(chip, struct mchp_core_pwm_chip, chip);
> +}
> +
> +static void mchp_core_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm,
> + bool enable, u64 period)
> +{
> + struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
> + u8 channel_enable, reg_offset, shift;
> +
> + /*
> + * There are two adjacent 8 bit control regs, the lower reg controls
> + * 0-7 and the upper reg 8-15. Check if the pwm is in the upper reg
> + * and if so, offset by the bus width.
> + */
> + reg_offset = MCHPCOREPWM_EN(pwm->hwpwm >> 3);
> + shift = pwm->hwpwm & 7;
> +
> + channel_enable = readb_relaxed(mchp_core_pwm->base + reg_offset);
> + channel_enable &= ~(1 << shift);
> + channel_enable |= (enable << shift);
> +
> + writel_relaxed(channel_enable, mchp_core_pwm->base + reg_offset);
> + mchp_core_pwm->channel_enabled &= ~BIT(pwm->hwpwm);
> + mchp_core_pwm->channel_enabled |= enable << pwm->hwpwm;
> +
> + /*
> + * Notify the block to update the waveform from the shadow registers.
> + * The updated values will not appear on the bus until they have been
> + * applied to the waveform at the beginning of the next period.
> + * This is a NO-OP if the channel does not have shadow registers.
> + */
> + if (mchp_core_pwm->sync_update_mask & (1 << pwm->hwpwm))
> + mchp_core_pwm->update_timestamp = ktime_add_ns(ktime_get(), period);
> +}
> +
> +static void mchp_core_pwm_wait_for_sync_update(struct mchp_core_pwm_chip *mchp_core_pwm,
> + unsigned int channel)
> +{
> + /*
> + * If a shadow register is used for this PWM channel, and iff there is
> + * a pending update to the waveform, we must wait for it to be applied
> + * before attempting to read its state. Reading the registers yields
> + * the currently implemented settings & the new ones are only readable
> + * once the current period has ended.
> + */
> +
> + if (mchp_core_pwm->sync_update_mask & (1 << channel)) {
> + ktime_t current_time = ktime_get();
> + s64 remaining_ns;
> + u32 delay_us;
> +
> + remaining_ns = ktime_to_ns(ktime_sub(mchp_core_pwm->update_timestamp,
> + current_time));
> +
> + /*
> + * If the update has gone through, don't bother waiting for
> + * obvious reasons. Otherwise wait around for an appropriate
> + * amount of time for the update to go through.
> + */
> + if (remaining_ns <= 0)
> + return;
> +
> + delay_us = DIV_ROUND_UP_ULL(remaining_ns, NSEC_PER_USEC);
> + if ((delay_us / 1000) > MAX_UDELAY_MS)
> + msleep(delay_us / 1000 + 1);
Is this better than
msleep(DIV_ROUND_UP(delay_us, 1000);
? Also I wonder about your usage of MAX_UDELAY_MS. This is about
udelay() but you're using usleep_range()?
> + else
> + usleep_range(delay_us, delay_us * 2);
I wonder if there isn't a function that implements something like
wait_until(mchp_core_pwm->update_timestamp);
which would be a bit nicer than doing this by hand. Maybe fsleep()?
> + }
> +}
> +
> +[...]
> +
> +static void mchp_core_pwm_apply_duty(struct pwm_chip *chip, struct pwm_device *pwm,
> + const struct pwm_state *state, u64 duty_steps,
> + u8 period_steps)
> +{
> + struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
> + u8 posedge, negedge;
> + u8 period_steps_val = PREG_TO_VAL(period_steps);
> +
> + /*
> + * Setting posedge == negedge doesn't yield a constant output,
> + * so that's an unsuitable setting to model duty_steps = 0.
> + * In that case set the unwanted edge to a value that never
> + * triggers.
> + */
> + if (state->polarity == PWM_POLARITY_INVERSED) {
> + negedge = !duty_steps ? period_steps_val : 0u;
IMHO
negedge = duty_steps ? 0 : period_steps_val;
is a bit easier to parse.
> + posedge = duty_steps;
> + } else {
> + posedge = !duty_steps ? period_steps_val : 0u;
> + negedge = duty_steps;
> + }
The following code is equivalent:
u8 first_edge = 0, second_edge = duty_steps;
/*
* Setting posedge == negedge doesn't yield a constant output,
* so that's an unsuitable setting to model duty_steps = 0.
* In that case set the unwanted edge to a value that never
* triggers.
*/
if (duty_steps == 0)
first_edge = period_steps_val;
if (state->polarity == PWM_POLARITY_INVERSED) {
negedge = first_edge;
posedge = second_edge;
} else {
posedge = first_edge;
negedge = second_edge;
}
I'm not sure if it's easier to understand. What do you think?
> + writel_relaxed(posedge, mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
> + writel_relaxed(negedge, mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
> +}
> +
> +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> + u16 *prescale, u8 *period_steps)
> +{
> + u64 tmp;
> +
> + /*
> + * Calculate the period cycles and prescale values.
> + * The registers are each 8 bits wide & multiplied to compute the period
> + * using the formula:
> + * (clock_period) * (prescale + 1) * (period_steps + 1)
> + * so the maximum period that can be generated is 0x10000 times the
> + * period of the input clock.
> + * However, due to the design of the "hardware", it is not possible to
> + * attain a 100% duty cycle if the full range of period_steps is used.
> + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> + * of the clock period attainable is 0xFF00.
> + */
> + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> +
> + /*
> + * The hardware adds one to the register value, so decrement by one to
> + * account for the offset
> + */
> + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> +
> + return;
> + }
> +
> + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
This looks wrong, but I didn't think long about that. Did we discuss
this already and/or are you sure this is correct?
(We have:
(prescale + 1) * (period_steps + 1)
period = ------------------------------------
clk_rate
You calculate
period * clk_rate
prescale = -------------------
NSEC_PER_SEC * 0xff
period * clk_rate
period_steps = ----------------------------- - 1
NSEC_PER_SEC * (prescale + 1)
assuming exact arithmetic putting these into the above equation we get:
period * clk_rate period * clk_rate
(------------------- + 1) * (-----------------------------) / clk_rate
NSEC_PER_SEC * 0xff NSEC_PER_SEC * (prescale + 1)
and then substituting prescale this doesn't resolve to period, does it?
Correct me if I'm wrong.)
> +}
> +
> +static inline void mchp_core_pwm_apply_period(struct mchp_core_pwm_chip *mchp_core_pwm,
> + u8 prescale, u8 period_steps)
> +{
> + writel_relaxed(prescale, mchp_core_pwm->base + MCHPCOREPWM_PRESCALE);
> + writel_relaxed(period_steps, mchp_core_pwm->base + MCHPCOREPWM_PERIOD);
> +}
There is only one caller for this two-line function. I suggest to unroll it?
> [...]
> +static int mchp_core_pwm_probe(struct platform_device *pdev)
> +{
> + struct mchp_core_pwm_chip *mchp_core_pwm;
> + struct resource *regs;
> + int ret;
> +
> + mchp_core_pwm = devm_kzalloc(&pdev->dev, sizeof(*mchp_core_pwm), GFP_KERNEL);
> + if (!mchp_core_pwm)
> + return -ENOMEM;
> +
> + mchp_core_pwm->base = devm_platform_get_and_ioremap_resource(pdev, 0, ®s);
> + if (IS_ERR(mchp_core_pwm->base))
> + return PTR_ERR(mchp_core_pwm->base);
> +
> + mchp_core_pwm->clk = devm_clk_get_enabled(&pdev->dev, NULL);
> + if (IS_ERR(mchp_core_pwm->clk))
> + return dev_err_probe(&pdev->dev, PTR_ERR(mchp_core_pwm->clk),
> + "failed to get PWM clock\n");
> +
> + if (of_property_read_u32(pdev->dev.of_node, "microchip,sync-update-mask",
> + &mchp_core_pwm->sync_update_mask))
> + mchp_core_pwm->sync_update_mask = 0;
> +
> + mutex_init(&mchp_core_pwm->lock);
> +
> + mchp_core_pwm->chip.dev = &pdev->dev;
> + mchp_core_pwm->chip.ops = &mchp_core_pwm_ops;
> + mchp_core_pwm->chip.npwm = 16;
> +
> + mchp_core_pwm->channel_enabled = readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_EN(0));
> + mchp_core_pwm->channel_enabled |=
> + readb_relaxed(mchp_core_pwm->base + MCHPCOREPWM_EN(1)) << 8;
> +
> + ret = devm_pwmchip_add(&pdev->dev, &mchp_core_pwm->chip);
> + if (ret < 0)
> + return dev_err_probe(&pdev->dev, ret, "failed to add PWM chip\n");
> +
> + /*
> + * Enabled synchronous update for channels with shadow registers
> + * enabled. For channels without shadow registers, this has no effect
> + * at all so is unconditionally enabled.
> + */
> + writel_relaxed(1U, mchp_core_pwm->base + MCHPCOREPWM_SYNC_UPD);
> + mchp_core_pwm->update_timestamp = ktime_get();
This needs to be done before devm_pwmchip_add().
> +
> + return 0;
> +}
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | https://www.pengutronix.de/ |
On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > From: Conor Dooley <[email protected]>
> > + delay_us = DIV_ROUND_UP_ULL(remaining_ns, NSEC_PER_USEC);
> > + if ((delay_us / 1000) > MAX_UDELAY_MS)
> > + msleep(delay_us / 1000 + 1);
>
> Is this better than
>
> msleep(DIV_ROUND_UP(delay_us, 1000);
>
> ? Also I wonder about your usage of MAX_UDELAY_MS. This is about
I probably started hacking on the example you gave and didn't notice
the U. What I have here is ~what you suggested last time.
> udelay() but you're using usleep_range()?
>
> > + else
> > + usleep_range(delay_us, delay_us * 2);
>
> I wonder if there isn't a function that implements something like
>
> wait_until(mchp_core_pwm->update_timestamp);
>
> which would be a bit nicer than doing this by hand. Maybe fsleep()?
That'd be fsleep(delay_us), but does at least clean up some of the
messing.
> > +static void mchp_core_pwm_apply_duty(struct pwm_chip *chip, struct pwm_device *pwm,
> > + const struct pwm_state *state, u64 duty_steps,
> > + u8 period_steps)
> > +{
> > + struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
> > + u8 posedge, negedge;
> > + u8 period_steps_val = PREG_TO_VAL(period_steps);
> > +
> > + /*
> > + * Setting posedge == negedge doesn't yield a constant output,
> > + * so that's an unsuitable setting to model duty_steps = 0.
> > + * In that case set the unwanted edge to a value that never
> > + * triggers.
> > + */
> > + if (state->polarity == PWM_POLARITY_INVERSED) {
> > + negedge = !duty_steps ? period_steps_val : 0u;
>
> IMHO
>
> negedge = duty_steps ? 0 : period_steps_val;
>
> is a bit easier to parse.
>
> > + posedge = duty_steps;
> > + } else {
> > + posedge = !duty_steps ? period_steps_val : 0u;
> > + negedge = duty_steps;
> > + }
>
> The following code is equivalent:
>
> u8 first_edge = 0, second_edge = duty_steps;
>
> /*
> * Setting posedge == negedge doesn't yield a constant output,
> * so that's an unsuitable setting to model duty_steps = 0.
> * In that case set the unwanted edge to a value that never
> * triggers.
> */
> if (duty_steps == 0)
> first_edge = period_steps_val;
>
> if (state->polarity == PWM_POLARITY_INVERSED) {
> negedge = first_edge;
> posedge = second_edge;
> } else {
> posedge = first_edge;
> negedge = second_edge;
> }
>
> I'm not sure if it's easier to understand. What do you think?
Despite having used them, I dislike ternary statements.
> > + writel_relaxed(posedge, mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
> > + writel_relaxed(negedge, mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
> > +}
> > +
> > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > + u16 *prescale, u8 *period_steps)
> > +{
> > + u64 tmp;
> > +
> > + /*
> > + * Calculate the period cycles and prescale values.
> > + * The registers are each 8 bits wide & multiplied to compute the period
> > + * using the formula:
> > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > + * so the maximum period that can be generated is 0x10000 times the
> > + * period of the input clock.
> > + * However, due to the design of the "hardware", it is not possible to
> > + * attain a 100% duty cycle if the full range of period_steps is used.
> > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > + * of the clock period attainable is 0xFF00.
> > + */
> > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > +
> > + /*
> > + * The hardware adds one to the register value, so decrement by one to
> > + * account for the offset
> > + */
> > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > +
> > + return;
> > + }
> > +
> > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
>
> This looks wrong, but I didn't think long about that. Did we discuss
> this already and/or are you sure this is correct?
We did discuss it previously AFAICT;
https://lore.kernel.org/linux-pwm/[email protected]/
In that version of the code, prescale_val meant the mathematical value
used for calculations & "prescale" was the value written into the
register.
Now, we have ditched prescale_val and operate directly with what gets
written into the register.
I ran a test case through the calculation, and it seemed to work out?
> (We have:
> (prescale + 1) * (period_steps + 1)
> period = ------------------------------------
> clk_rate
>
> You calculate
> period * clk_rate
> prescale = -------------------
> NSEC_PER_SEC * 0xff
Say period = 2000 ns, clk_rate = 62.5 Mhz, giving a register value for
prescale of 0.49019...
> period * clk_rate
> period_steps = ----------------------------- - 1
> NSEC_PER_SEC * (prescale + 1)
Same numbers, but we use the PREG_TO_VAL() macro so the mathematical value
is 1.49019.
2000 * 62.5E6
--------------------- - 1 = 82.88360....
1E9 * (0.49016 + 1)
>
> assuming exact arithmetic putting these into the above equation we get:
>
>
> period * clk_rate period * clk_rate
> (------------------- + 1) * (-----------------------------) / clk_rate
> NSEC_PER_SEC * 0xff NSEC_PER_SEC * (prescale + 1)
>
> and then substituting prescale this doesn't resolve to period, does it?
> Correct me if I'm wrong.)
(0.49016 + 1) * (82.88360 + 1) 124.99...
------------------------------ = ------------- = 0.00000199999
62.5E6 62.5E6
And then accounting for that fact that 2000 was really 2000E-9,
we arrive back where we started, give or take some rounding?
Doing that with integer maths works out more cleanly since 0.49016
becomes 0.
2000 * 62.5E6
------------------ - 1 = 124
1E9 * (0 + 1)
(0 + 1) * (124 + 1) 125
------------------- = --------- = 0.000002
62.5E6 62.5E6
Unfortunately, I don't think I am seeing what you're seeing.
> period * clk_rate period * clk_rate
> (------------------- + 1) * (-----------------------------) / clk_rate
> NSEC_PER_SEC * 0xff NSEC_PER_SEC * (prescale + 1)
^
It may be this + 1, which I don't seem to have accounted for in my quick
run through a calculation?
*prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
*period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
The code does not add a 1 when it calculates prescale, only when it uses
the result to calculate period_steps, since prescale & period_steps are
the register values, not the "mathematical" ones.
Hopefully I've not gone and made a fool of myself...
> > +static inline void mchp_core_pwm_apply_period(struct mchp_core_pwm_chip *mchp_core_pwm,
> > + u8 prescale, u8 period_steps)
> > +{
> > + writel_relaxed(prescale, mchp_core_pwm->base + MCHPCOREPWM_PRESCALE);
> > + writel_relaxed(period_steps, mchp_core_pwm->base + MCHPCOREPWM_PERIOD);
> > +}
>
> There is only one caller for this two-line function. I suggest to unroll it?
Sure.
> > + ret = devm_pwmchip_add(&pdev->dev, &mchp_core_pwm->chip);
> > + if (ret < 0)
> > + return dev_err_probe(&pdev->dev, ret, "failed to add PWM chip\n");
> > +
> > + /*
> > + * Enabled synchronous update for channels with shadow registers
> > + * enabled. For channels without shadow registers, this has no effect
> > + * at all so is unconditionally enabled.
> > + */
> > + writel_relaxed(1U, mchp_core_pwm->base + MCHPCOREPWM_SYNC_UPD);
> > + mchp_core_pwm->update_timestamp = ktime_get();
>
> This needs to be done before devm_pwmchip_add().
Makes sense, woops. I think I've revised this to the point that my
blinkers have turned on & I'll wait a while before resubmitting in order
to hopefully reset that.
Perhaps I need to watch a lecture on how to write a PWM driver since I
am clearly no good at it, given the 15 revisions. Do you know of any?
Thanks,
Conor.
Hello Conor,
On Wed, Jan 11, 2023 at 12:15:29AM +0000, Conor Dooley wrote:
> On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> > On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > > From: Conor Dooley <[email protected]>
>
> > > + delay_us = DIV_ROUND_UP_ULL(remaining_ns, NSEC_PER_USEC);
> > > + if ((delay_us / 1000) > MAX_UDELAY_MS)
> > > + msleep(delay_us / 1000 + 1);
> >
> > Is this better than
> >
> > msleep(DIV_ROUND_UP(delay_us, 1000);
> >
> > ? Also I wonder about your usage of MAX_UDELAY_MS. This is about
>
> I probably started hacking on the example you gave and didn't notice
> the U. What I have here is ~what you suggested last time.
A series with (up to now) 13 revisions and long delays between the
review rounds (which are mostly attributed to my time schedule) is
difficult to handle on both sides. Some repetition isn't easy to prevent
in such a case. Sorry for that.
> > udelay() but you're using usleep_range()?
> >
> > > + else
> > > + usleep_range(delay_us, delay_us * 2);
> >
> > I wonder if there isn't a function that implements something like
> >
> > wait_until(mchp_core_pwm->update_timestamp);
> >
> > which would be a bit nicer than doing this by hand. Maybe fsleep()?
>
> That'd be fsleep(delay_us), but does at least clean up some of the
> messing.
>
> > > +static void mchp_core_pwm_apply_duty(struct pwm_chip *chip, struct pwm_device *pwm,
> > > + const struct pwm_state *state, u64 duty_steps,
> > > + u8 period_steps)
> > > +{
> > > + struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
> > > + u8 posedge, negedge;
> > > + u8 period_steps_val = PREG_TO_VAL(period_steps);
> > > +
> > > + /*
> > > + * Setting posedge == negedge doesn't yield a constant output,
> > > + * so that's an unsuitable setting to model duty_steps = 0.
> > > + * In that case set the unwanted edge to a value that never
> > > + * triggers.
> > > + */
> > > + if (state->polarity == PWM_POLARITY_INVERSED) {
> > > + negedge = !duty_steps ? period_steps_val : 0u;
> >
> > IMHO
> >
> > negedge = duty_steps ? 0 : period_steps_val;
> >
> > is a bit easier to parse.
> >
> > > + posedge = duty_steps;
> > > + } else {
> > > + posedge = !duty_steps ? period_steps_val : 0u;
> > > + negedge = duty_steps;
> > > + }
> >
> > The following code is equivalent:
> >
> > u8 first_edge = 0, second_edge = duty_steps;
> >
> > /*
> > * Setting posedge == negedge doesn't yield a constant output,
> > * so that's an unsuitable setting to model duty_steps = 0.
> > * In that case set the unwanted edge to a value that never
> > * triggers.
> > */
> > if (duty_steps == 0)
> > first_edge = period_steps_val;
> >
> > if (state->polarity == PWM_POLARITY_INVERSED) {
> > negedge = first_edge;
> > posedge = second_edge;
> > } else {
> > posedge = first_edge;
> > negedge = second_edge;
> > }
> >
> > I'm not sure if it's easier to understand. What do you think?
>
> Despite having used them, I dislike ternary statements.
My variant is a bit longer and uses more variables, but has less
repetition. I don't expect a relevant change on the generated code. I
slightly prefer my variant, but I let you choose which one you prefer.
> > > + writel_relaxed(posedge, mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
> > > + writel_relaxed(negedge, mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
> > > +}
> > > +
> > > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > > + u16 *prescale, u8 *period_steps)
> > > +{
> > > + u64 tmp;
> > > +
> > > + /*
> > > + * Calculate the period cycles and prescale values.
> > > + * The registers are each 8 bits wide & multiplied to compute the period
> > > + * using the formula:
> > > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > > + * so the maximum period that can be generated is 0x10000 times the
> > > + * period of the input clock.
> > > + * However, due to the design of the "hardware", it is not possible to
> > > + * attain a 100% duty cycle if the full range of period_steps is used.
> > > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > > + * of the clock period attainable is 0xFF00.
> > > + */
> > > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > > +
> > > + /*
> > > + * The hardware adds one to the register value, so decrement by one to
> > > + * account for the offset
> > > + */
> > > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > > +
> > > + return;
> > > + }
> > > +
> > > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
> >
> > This looks wrong, but I didn't think long about that. Did we discuss
> > this already and/or are you sure this is correct?
>
> We did discuss it previously AFAICT;
> https://lore.kernel.org/linux-pwm/[email protected]/
>
> [...]
> Unfortunately, I don't think I am seeing what you're seeing.
Well, the calculation lands in the right ballpark for sure, but if my
intuition is right, it's not as exact as it could be. I need some time
with pencil and paper ...
> [...]
> Perhaps I need to watch a lecture on how to write a PWM driver since I
> am clearly no good at it, given the 15 revisions. Do you know of any?
I'm not aware of such a lecture. I'm willing to take the blame for some
of the revisions because I'm very picky and the math involved here isn't
trivial. And I sometimes wonder about myself pointing out an issue in
(say) v5 which was there unnoticed already in v1.
In sum a patch series going through such a high number of revisions is
mostly a good sign. In the end we can be sure that the merged code is
checked deep-rootedly and that both you and me have a certain amount of
endurance. :-)
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | https://www.pengutronix.de/ |
Hey Uwe,
On Wed, Jan 11, 2023 at 08:02:50AM +0100, Uwe Kleine-K?nig wrote:
> On Wed, Jan 11, 2023 at 12:15:29AM +0000, Conor Dooley wrote:
> > On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> > > On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > > > From: Conor Dooley <[email protected]>
> >
> > > > + delay_us = DIV_ROUND_UP_ULL(remaining_ns, NSEC_PER_USEC);
> > > > + if ((delay_us / 1000) > MAX_UDELAY_MS)
> > > > + msleep(delay_us / 1000 + 1);
> > >
> > > Is this better than
> > >
> > > msleep(DIV_ROUND_UP(delay_us, 1000);
> > >
> > > ? Also I wonder about your usage of MAX_UDELAY_MS. This is about
> >
> > I probably started hacking on the example you gave and didn't notice
> > the U. What I have here is ~what you suggested last time.
>
> A series with (up to now) 13 revisions and long delays between the
> review rounds (which are mostly attributed to my time schedule) is
> difficult to handle on both sides. Some repetition isn't easy to prevent
> in such a case. Sorry for that.
It is what it is, you've only got so much time :)
> > > udelay() but you're using usleep_range()?
> > >
> > > > + else
> > > > + usleep_range(delay_us, delay_us * 2);
> > >
> > > I wonder if there isn't a function that implements something like
> > >
> > > wait_until(mchp_core_pwm->update_timestamp);
> > >
> > > which would be a bit nicer than doing this by hand. Maybe fsleep()?
> >
> > That'd be fsleep(delay_us), but does at least clean up some of the
> > messing.
> >
> > > > +static void mchp_core_pwm_apply_duty(struct pwm_chip *chip, struct pwm_device *pwm,
> > > > + const struct pwm_state *state, u64 duty_steps,
> > > > + u8 period_steps)
> > > > +{
> > > > + struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
> > > > + u8 posedge, negedge;
> > > > + u8 period_steps_val = PREG_TO_VAL(period_steps);
> > > > +
> > > > + /*
> > > > + * Setting posedge == negedge doesn't yield a constant output,
> > > > + * so that's an unsuitable setting to model duty_steps = 0.
> > > > + * In that case set the unwanted edge to a value that never
> > > > + * triggers.
> > > > + */
> > > > + if (state->polarity == PWM_POLARITY_INVERSED) {
> > > > + negedge = !duty_steps ? period_steps_val : 0u;
> > >
> > > IMHO
> > >
> > > negedge = duty_steps ? 0 : period_steps_val;
> > >
> > > is a bit easier to parse.
> > >
> > > > + posedge = duty_steps;
> > > > + } else {
> > > > + posedge = !duty_steps ? period_steps_val : 0u;
> > > > + negedge = duty_steps;
> > > > + }
> > >
> > > The following code is equivalent:
> > >
> > > u8 first_edge = 0, second_edge = duty_steps;
> > >
> > > /*
> > > * Setting posedge == negedge doesn't yield a constant output,
> > > * so that's an unsuitable setting to model duty_steps = 0.
> > > * In that case set the unwanted edge to a value that never
> > > * triggers.
> > > */
> > > if (duty_steps == 0)
> > > first_edge = period_steps_val;
> > >
> > > if (state->polarity == PWM_POLARITY_INVERSED) {
> > > negedge = first_edge;
> > > posedge = second_edge;
> > > } else {
> > > posedge = first_edge;
> > > negedge = second_edge;
> > > }
> > >
> > > I'm not sure if it's easier to understand. What do you think?
> >
> > Despite having used them, I dislike ternary statements.
>
> My variant is a bit longer and uses more variables, but has less
> repetition. I don't expect a relevant change on the generated code. I
> slightly prefer my variant, but I let you choose which one you prefer.
Yah, I prefer anything that doesn't have ternarys in it.
> > > > + writel_relaxed(posedge, mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
> > > > + writel_relaxed(negedge, mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
> > > > +}
> > > > +
> > > > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > > > + u16 *prescale, u8 *period_steps)
> > > > +{
> > > > + u64 tmp;
> > > > +
> > > > + /*
> > > > + * Calculate the period cycles and prescale values.
> > > > + * The registers are each 8 bits wide & multiplied to compute the period
> > > > + * using the formula:
> > > > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > > > + * so the maximum period that can be generated is 0x10000 times the
> > > > + * period of the input clock.
> > > > + * However, due to the design of the "hardware", it is not possible to
> > > > + * attain a 100% duty cycle if the full range of period_steps is used.
> > > > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > > > + * of the clock period attainable is 0xFF00.
> > > > + */
> > > > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > > > +
> > > > + /*
> > > > + * The hardware adds one to the register value, so decrement by one to
> > > > + * account for the offset
> > > > + */
> > > > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > > > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > > > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > > > +
> > > > + return;
> > > > + }
> > > > +
> > > > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > > > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > > > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
> > >
> > > This looks wrong, but I didn't think long about that. Did we discuss
> > > this already and/or are you sure this is correct?
> >
> > We did discuss it previously AFAICT;
> > https://lore.kernel.org/linux-pwm/[email protected]/
> >
> > [...]
> > Unfortunately, I don't think I am seeing what you're seeing.
>
> Well, the calculation lands in the right ballpark for sure, but if my
> intuition is right, it's not as exact as it could be. I need some time
> with pencil and paper ...
>
> > [...]
> > Perhaps I need to watch a lecture on how to write a PWM driver since I
> > am clearly no good at it, given the 15 revisions. Do you know of any?
>
> I'm not aware of such a lecture.
I thought you were doing one at FOSDEM!
> I'm willing to take the blame for some
> of the revisions because I'm very picky and the math involved here isn't
> trivial.
I'd rather the maths was right. Fixing it up front is better than trying
to debug it from a customer complaint - so thanks for that.
And the maths was very naive to begin with, although I only submitted it
in the summer, I think I wrote the driver prior to having upstreamed a
single patch, and I think that showed in the maths.
> And I sometimes wonder about myself pointing out an issue in
> (say) v5 which was there unnoticed already in v1.
I dunno. I feel bad if I do that too - but if the problem you didn't
notice earlier on is a bug, rather than some sort of style comment, I
don't see why you wouldn't call it out.
> In sum a patch series going through such a high number of revisions is
> mostly a good sign.
Or that it was poor to begin with & barely improved over time...
> In the end we can be sure that the merged code is
> checked deep-rootedly and that both you and me have a certain amount of
> endurance. :-)
I wasn't really blaming you for the number of revisions, the number of
silly mistakes I've made really irritates me.
Thanks,
Conor.
Hello Conor,
On Wed, Jan 11, 2023 at 08:00:51AM +0000, Conor Dooley wrote:
> > > [...]
> > > Perhaps I need to watch a lecture on how to write a PWM driver since I
> > > am clearly no good at it, given the 15 revisions. Do you know of any?
> >
> > I'm not aware of such a lecture.
>
> I thought you were doing one at FOSDEM!
Oh that knowledge already spread? Anyhow that doesn't help you today
:-)
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | https://www.pengutronix.de/ |
Hello,
On Wed, Jan 11, 2023 at 08:02:50AM +0100, Uwe Kleine-K?nig wrote:
> On Wed, Jan 11, 2023 at 12:15:29AM +0000, Conor Dooley wrote:
> > On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> > > On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > > > From: Conor Dooley <[email protected]>
> >
> > > > + delay_us = DIV_ROUND_UP_ULL(remaining_ns, NSEC_PER_USEC);
> > > > + if ((delay_us / 1000) > MAX_UDELAY_MS)
> > > > + msleep(delay_us / 1000 + 1);
> > >
> > > Is this better than
> > >
> > > msleep(DIV_ROUND_UP(delay_us, 1000);
> > >
> > > ? Also I wonder about your usage of MAX_UDELAY_MS. This is about
> >
> > I probably started hacking on the example you gave and didn't notice
> > the U. What I have here is ~what you suggested last time.
>
> A series with (up to now) 13 revisions and long delays between the
> review rounds (which are mostly attributed to my time schedule) is
> difficult to handle on both sides. Some repetition isn't easy to prevent
> in such a case. Sorry for that.
>
> > > udelay() but you're using usleep_range()?
> > >
> > > > + else
> > > > + usleep_range(delay_us, delay_us * 2);
> > >
> > > I wonder if there isn't a function that implements something like
> > >
> > > wait_until(mchp_core_pwm->update_timestamp);
> > >
> > > which would be a bit nicer than doing this by hand. Maybe fsleep()?
> >
> > That'd be fsleep(delay_us), but does at least clean up some of the
> > messing.
> >
> > > > +static void mchp_core_pwm_apply_duty(struct pwm_chip *chip, struct pwm_device *pwm,
> > > > + const struct pwm_state *state, u64 duty_steps,
> > > > + u8 period_steps)
> > > > +{
> > > > + struct mchp_core_pwm_chip *mchp_core_pwm = to_mchp_core_pwm(chip);
> > > > + u8 posedge, negedge;
> > > > + u8 period_steps_val = PREG_TO_VAL(period_steps);
> > > > +
> > > > + /*
> > > > + * Setting posedge == negedge doesn't yield a constant output,
> > > > + * so that's an unsuitable setting to model duty_steps = 0.
> > > > + * In that case set the unwanted edge to a value that never
> > > > + * triggers.
> > > > + */
> > > > + if (state->polarity == PWM_POLARITY_INVERSED) {
> > > > + negedge = !duty_steps ? period_steps_val : 0u;
> > >
> > > IMHO
> > >
> > > negedge = duty_steps ? 0 : period_steps_val;
> > >
> > > is a bit easier to parse.
> > >
> > > > + posedge = duty_steps;
> > > > + } else {
> > > > + posedge = !duty_steps ? period_steps_val : 0u;
> > > > + negedge = duty_steps;
> > > > + }
> > >
> > > The following code is equivalent:
> > >
> > > u8 first_edge = 0, second_edge = duty_steps;
> > >
> > > /*
> > > * Setting posedge == negedge doesn't yield a constant output,
> > > * so that's an unsuitable setting to model duty_steps = 0.
> > > * In that case set the unwanted edge to a value that never
> > > * triggers.
> > > */
> > > if (duty_steps == 0)
> > > first_edge = period_steps_val;
> > >
> > > if (state->polarity == PWM_POLARITY_INVERSED) {
> > > negedge = first_edge;
> > > posedge = second_edge;
> > > } else {
> > > posedge = first_edge;
> > > negedge = second_edge;
> > > }
> > >
> > > I'm not sure if it's easier to understand. What do you think?
> >
> > Despite having used them, I dislike ternary statements.
>
> My variant is a bit longer and uses more variables, but has less
> repetition. I don't expect a relevant change on the generated code. I
> slightly prefer my variant, but I let you choose which one you prefer.
>
> > > > + writel_relaxed(posedge, mchp_core_pwm->base + MCHPCOREPWM_POSEDGE(pwm->hwpwm));
> > > > + writel_relaxed(negedge, mchp_core_pwm->base + MCHPCOREPWM_NEGEDGE(pwm->hwpwm));
> > > > +}
> > > > +
> > > > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > > > + u16 *prescale, u8 *period_steps)
> > > > +{
> > > > + u64 tmp;
> > > > +
> > > > + /*
> > > > + * Calculate the period cycles and prescale values.
> > > > + * The registers are each 8 bits wide & multiplied to compute the period
> > > > + * using the formula:
> > > > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > > > + * so the maximum period that can be generated is 0x10000 times the
> > > > + * period of the input clock.
> > > > + * However, due to the design of the "hardware", it is not possible to
> > > > + * attain a 100% duty cycle if the full range of period_steps is used.
> > > > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > > > + * of the clock period attainable is 0xFF00.
> > > > + */
> > > > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > > > +
> > > > + /*
> > > > + * The hardware adds one to the register value, so decrement by one to
> > > > + * account for the offset
> > > > + */
> > > > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > > > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > > > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > > > +
> > > > + return;
> > > > + }
> > > > +
> > > > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > > > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > > > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
> > >
> > > This looks wrong, but I didn't think long about that. Did we discuss
> > > this already and/or are you sure this is correct?
> >
> > We did discuss it previously AFAICT;
> > https://lore.kernel.org/linux-pwm/[email protected]/
> >
> > [...]
> > Unfortunately, I don't think I am seeing what you're seeing.
>
> Well, the calculation lands in the right ballpark for sure, but if my
> intuition is right, it's not as exact as it could be. I need some time
> with pencil and paper ...
Just a small heads up:
I thought a bit about that (without pencil and paper on my way to work
today), and the optimal solution is non-trivial. In fact you have to
pick parameters A and B such that for a given C
(A + 1) * (B + 1) is maximal with
0 <= A < 0x100
0 <= B < 0xff
(A + 1) * (B + 1) <= C
A consistent non-optimal choice that is easier to calculate than a
complete search would be nice. But I think we're not there yet.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | https://www.pengutronix.de/ |
Hello,
On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> Hello Conor,
>
> On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > + u16 *prescale, u8 *period_steps)
> > +{
> > + u64 tmp;
> > +
> > + /*
> > + * Calculate the period cycles and prescale values.
> > + * The registers are each 8 bits wide & multiplied to compute the period
> > + * using the formula:
> > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > + * so the maximum period that can be generated is 0x10000 times the
> > + * period of the input clock.
> > + * However, due to the design of the "hardware", it is not possible to
> > + * attain a 100% duty cycle if the full range of period_steps is used.
> > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > + * of the clock period attainable is 0xFF00.
> > + */
> > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > +
> > + /*
> > + * The hardware adds one to the register value, so decrement by one to
> > + * account for the offset
> > + */
> > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > +
> > + return;
> > + }
> > +
> > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
>
> This looks wrong, but I didn't think long about that. Did we discuss
> this already and/or are you sure this is correct?
>
> (We have:
> (prescale + 1) * (period_steps + 1)
> period = ------------------------------------
> clk_rate
>
We want prescale small such that period_steps can be big to give
fine-grained control over the available duty_cycles. period_steps is a
8-bit value < 0xff, so we get:
period * clk_rate
prescale = ------------------- - 1
NSEC_PER_SEC * 0xff
which in code then reads:
*prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX)
if (*prescale)
*prescale -= 1;
> You calculate
> period * clk_rate
> prescale = -------------------
> NSEC_PER_SEC * 0xff
>
> period * clk_rate
> period_steps = ----------------------------- - 1
> NSEC_PER_SEC * (prescale + 1)
The formula for period_steps is right.
Please double-check!
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | https://www.pengutronix.de/ |
On Thu, Jan 12, 2023 at 01:01:41PM +0100, Uwe Kleine-K?nig wrote:
> Hello,
>
> On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> > Hello Conor,
> >
> > On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > > + u16 *prescale, u8 *period_steps)
> > > +{
> > > + u64 tmp;
> > > +
> > > + /*
> > > + * Calculate the period cycles and prescale values.
> > > + * The registers are each 8 bits wide & multiplied to compute the period
> > > + * using the formula:
> > > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > > + * so the maximum period that can be generated is 0x10000 times the
> > > + * period of the input clock.
> > > + * However, due to the design of the "hardware", it is not possible to
> > > + * attain a 100% duty cycle if the full range of period_steps is used.
> > > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > > + * of the clock period attainable is 0xFF00.
> > > + */
> > > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > > +
> > > + /*
> > > + * The hardware adds one to the register value, so decrement by one to
> > > + * account for the offset
> > > + */
> > > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > > +
> > > + return;
> > > + }
> > > +
> > > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
> >
> > This looks wrong, but I didn't think long about that. Did we discuss
> > this already and/or are you sure this is correct?
> >
> > (We have:
> > (prescale + 1) * (period_steps + 1)
> > period = ------------------------------------
> > clk_rate
> >
>
> We want prescale small such that period_steps can be big to give
> fine-grained control over the available duty_cycles. period_steps is a
> 8-bit value < 0xff, so we get:
>
> period * clk_rate
> prescale = ------------------- - 1
> NSEC_PER_SEC * 0xff
>
> which in code then reads:
>
> *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX)
> if (*prescale)
> *prescale -= 1;
>
>
> > You calculate
> > period * clk_rate
> > prescale = -------------------
> > NSEC_PER_SEC * 0xff
> >
> > period * clk_rate
> > period_steps = ----------------------------- - 1
> > NSEC_PER_SEC * (prescale + 1)
>
> The formula for period_steps is right.
I stood in front of the whiteboard for a bit to puzzle it all out and
have come to the realisation that you are right. I was implicitly
converting in my head from "mathematical" values to register values &
therefore not subtracting. I must've hyperfocused on the underflow when
I adjusted your suggestion back in v5 or w/e it was.
I must also have got rather unlucky that the configurations I picked to
check whether the calculations worked out, happened to. I suppose as
well, the way in which it was mis-calculating also avoids the PWM_DEBUG
complaints too.
Perhaps I'll insert your nice formulae in the next version in comments,
so they're there for next time.
Thanks again & sorry for consuming so much of your time on this,
Conor.
On Thu, Jan 12, 2023 at 03:10:09PM +0000, Conor Dooley wrote:
> On Thu, Jan 12, 2023 at 01:01:41PM +0100, Uwe Kleine-K?nig wrote:
> > Hello,
> >
> > On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> > > Hello Conor,
> > >
> > > On Wed, Dec 21, 2022 at 11:29:12AM +0000, Conor Dooley wrote:
> > > > +static void mchp_core_pwm_calc_period(const struct pwm_state *state, unsigned long clk_rate,
> > > > + u16 *prescale, u8 *period_steps)
> > > > +{
> > > > + u64 tmp;
> > > > +
> > > > + /*
> > > > + * Calculate the period cycles and prescale values.
> > > > + * The registers are each 8 bits wide & multiplied to compute the period
> > > > + * using the formula:
> > > > + * (clock_period) * (prescale + 1) * (period_steps + 1)
> > > > + * so the maximum period that can be generated is 0x10000 times the
> > > > + * period of the input clock.
> > > > + * However, due to the design of the "hardware", it is not possible to
> > > > + * attain a 100% duty cycle if the full range of period_steps is used.
> > > > + * Therefore period_steps is restricted to 0xFE and the maximum multiple
> > > > + * of the clock period attainable is 0xFF00.
> > > > + */
> > > > + tmp = mul_u64_u64_div_u64(state->period, clk_rate, NSEC_PER_SEC);
> > > > +
> > > > + /*
> > > > + * The hardware adds one to the register value, so decrement by one to
> > > > + * account for the offset
> > > > + */
> > > > + if (tmp >= MCHPCOREPWM_PERIOD_MAX) {
> > > > + *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > > > + *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> > > > +
> > > > + return;
> > > > + }
> > > > +
> > > > + *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX);
> > > > + /* PREG_TO_VAL() can produce a value larger than UINT8_MAX */
> > > > + *period_steps = div_u64(tmp, PREG_TO_VAL(*prescale)) - 1;
> > >
> > > This looks wrong, but I didn't think long about that. Did we discuss
> > > this already and/or are you sure this is correct?
> > >
> > > (We have:
> > > (prescale + 1) * (period_steps + 1)
> > > period = ------------------------------------
> > > clk_rate
> > >
> >
> > We want prescale small such that period_steps can be big to give
> > fine-grained control over the available duty_cycles. period_steps is a
> > 8-bit value < 0xff, so we get:
> >
> > period * clk_rate
> > prescale = ------------------- - 1
> > NSEC_PER_SEC * 0xff
> >
> > which in code then reads:
> >
> > *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX)
> > if (*prescale)
> > *prescale -= 1;
> >
> >
> > > You calculate
> > > period * clk_rate
> > > prescale = -------------------
> > > NSEC_PER_SEC * 0xff
> > >
> > > period * clk_rate
> > > period_steps = ----------------------------- - 1
> > > NSEC_PER_SEC * (prescale + 1)
> >
> > The formula for period_steps is right.
>
> I stood in front of the whiteboard for a bit to puzzle it all out and
> have come to the realisation that you are right. I was implicitly
> converting in my head from "mathematical" values to register values &
> therefore not subtracting. I must've hyperfocused on the underflow when
> I adjusted your suggestion back in v5 or w/e it was.
>
> I must also have got rather unlucky that the configurations I picked to
> check whether the calculations worked out, happened to. I suppose as
> well, the way in which it was mis-calculating also avoids the PWM_DEBUG
> complaints too.
>
> Perhaps I'll insert your nice formulae in the next version in comments,
> so they're there for next time.
*sigh*, me again...
Picked this up this afternoon to try and respin a v14 and ran into a bit
of an issue with this suggestion:
> > *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX)
> > if (*prescale)
> > *prescale -= 1;
In theory this works out, but with integer division it doesn't AFAICT.
Take for example:
period_ns = 10,000
clk_rate = 62.5 MHz
The prescale calculation is:
(10000 * 62.5E6) / (1E9 * 255) - 1 = 1.451 -> 1
For period_steps then:
(10000 * 62.5E6) / (1E9 * (1 + 1)) - 1 = 311.5 -> 311
prescale is a u16, since it's valid for that division to return 256.
The register is only 8 bits wide though, so 311 overflows it and 55 ends
up in the register.
The period then is:
(55 + 1) * (1 + 1) / 62.5E6, or a period of 1792 ns.
I think it needs to be a div_u64_round_up(), which I know is not a real
function, otherwise we compute invalid values for period steps.
Quoting you previously:
> I thought a bit about that (without pencil and paper on my way to work
> today), and the optimal solution is non-trivial. In fact you have to
> pick parameters A and B such that for a given C
>
> (A + 1) * (B + 1) is maximal with
>
> 0 <= A < 0x100
> 0 <= B < 0xff
> (A + 1) * (B + 1) <= C
As we need (period_steps + 1) * (prescale + 1) maximal, *but* also want
to maximise period_steps so that duty resolution etc is maximal too.
We pick prescale, using the formula below, by setting period_steps to
the maximum possible value:
> period * clk_rate
> prescale = -------------------
> NSEC_PER_SEC * 0xff
Given we set period_steps to the max here, we only actually pick the
lower bound on prescale, not the actual value of it.
We must round it to the nearest possible value before using it to go
back and calculate period_steps.
With the previous code, missing the -= 1, the division result was purely
truncated:
(10000 * 62.5E6) / (1E9 * 255) = 2.451 -> 2
That 2 was written into the register, and then the hardware rounds that
up to 3, as does the period_steps calculation.
period_steps here is:
(10000 * 62.5E6) / (1E9 * (2 + 1)) - 1 = 207.833 -> 207
Finally, the period:
(207 + 1) * (2 + 1) / 62.5E6, or a period of 9984 ns.
This is the same operation, unless I am yet again overlooking something,
as doing a div_u64_round_up() type thing, followed by a subtraction of 1
We don't need to worry about writing something too big into the register
either, as we are protected against values of tmp that, when divided by
0xff, would produce values larger than 255:
> /*
> * The hardware adds one to the register value, so decrement by one to
> * account for the offset
> */
> if (tmp >= MCHPCOREPWM_PERIOD_MAX) { (PERIOD_MAX is 0xff00)
> *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
>
> return;
> }
What am I missing this time? haha
Thanks,
Conor.
Hey Uwe!
Was nice to meet you at FOSDEM, if I'd seen that presentation before
working on this driver I think the version count would have been
substantially lower!
On Fri, Jan 20, 2023 at 07:40:32PM +0000, Conor Dooley wrote:
> On Thu, Jan 12, 2023 at 03:10:09PM +0000, Conor Dooley wrote:
> > On Thu, Jan 12, 2023 at 01:01:41PM +0100, Uwe Kleine-K?nig wrote:
> > > On Tue, Jan 10, 2023 at 11:48:05PM +0100, Uwe Kleine-K?nig wrote:
> *sigh*, me again...
>
> Picked this up this afternoon to try and respin a v14 and ran into a bit
> of an issue with this suggestion:
>
> > > *prescale = div_u64(tmp, MCHPCOREPWM_PERIOD_STEPS_MAX)
> > > if (*prescale)
> > > *prescale -= 1;
>
> In theory this works out, but with integer division it doesn't AFAICT.
>
> Take for example:
> period_ns = 10,000
> clk_rate = 62.5 MHz
>
> The prescale calculation is:
> (10000 * 62.5E6) / (1E9 * 255) - 1 = 1.451 -> 1
>
> For period_steps then:
> (10000 * 62.5E6) / (1E9 * (1 + 1)) - 1 = 311.5 -> 311
>
> prescale is a u16, since it's valid for that division to return 256.
> The register is only 8 bits wide though, so 311 overflows it and 55 ends
> up in the register.
> The period then is:
> (55 + 1) * (1 + 1) / 62.5E6, or a period of 1792 ns.
>
> I think it needs to be a div_u64_round_up(), which I know is not a real
> function, otherwise we compute invalid values for period steps.
>
> Quoting you previously:
> > I thought a bit about that (without pencil and paper on my way to work
> > today), and the optimal solution is non-trivial. In fact you have to
> > pick parameters A and B such that for a given C
> >
> > (A + 1) * (B + 1) is maximal with
> >
> > 0 <= A < 0x100
> > 0 <= B < 0xff
> > (A + 1) * (B + 1) <= C
>
> As we need (period_steps + 1) * (prescale + 1) maximal, *but* also want
> to maximise period_steps so that duty resolution etc is maximal too.
> We pick prescale, using the formula below, by setting period_steps to
> the maximum possible value:
> > period * clk_rate
> > prescale = -------------------
> > NSEC_PER_SEC * 0xff
>
> Given we set period_steps to the max here, we only actually pick the
> lower bound on prescale, not the actual value of it.
> We must round it to the nearest possible value before using it to go
> back and calculate period_steps.
>
> With the previous code, missing the -= 1, the division result was purely
> truncated:
> (10000 * 62.5E6) / (1E9 * 255) = 2.451 -> 2
> That 2 was written into the register, and then the hardware rounds that
> up to 3, as does the period_steps calculation.
>
> period_steps here is:
> (10000 * 62.5E6) / (1E9 * (2 + 1)) - 1 = 207.833 -> 207
>
> Finally, the period:
> (207 + 1) * (2 + 1) / 62.5E6, or a period of 9984 ns.
>
> This is the same operation, unless I am yet again overlooking something,
> as doing a div_u64_round_up() type thing, followed by a subtraction of 1
>
> We don't need to worry about writing something too big into the register
> either, as we are protected against values of tmp that, when divided by
> 0xff, would produce values larger than 255:
> > /*
> > * The hardware adds one to the register value, so decrement by one to
> > * account for the offset
> > */
> > if (tmp >= MCHPCOREPWM_PERIOD_MAX) { (PERIOD_MAX is 0xff00)
> > *prescale = MCHPCOREPWM_PRESCALE_MAX - 1;
> > *period_steps = MCHPCOREPWM_PERIOD_STEPS_MAX - 1;
> >
> > return;
> > }
>
> What am I missing this time? haha
So my "plan" I guess is to rebase this on v6.3-rc1 & re-submit with the
various minor bits fixed.
Trying the proposed "fixes" to the period calculation that we had
discussed pointed out the above issue, and it appears, to me at least,
that we made a mess of translating from regular calculations to integer
ones.
Cheers,
Conor.