If the extcon device exists, get the mode from the extcon device. If
the controller is DRD and the driver is unable to determine the mode,
only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
Cc: Felipe Balbi <[email protected]>
Cc: Thinh Nguyen <[email protected]>
Cc: [email protected]
Cc: [email protected]
Reviewed-by: Thinh Nguyen <[email protected]>
Signed-off-by: Andrey Smirnov <[email protected]>
---
v1 of the patch:
https://lore.kernel.org/linux-usb/[email protected]/T/#u
previons discussion:
https://lore.kernel.org/linux-usb/[email protected]/
drivers/usb/dwc3/core.c | 56 ++++++++++++++++++++++++++++++++++++++++-
drivers/usb/dwc3/drd.c | 50 ------------------------------------
2 files changed, 55 insertions(+), 51 deletions(-)
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index f2448d0a9d39..09f283288ce7 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -23,6 +23,7 @@
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/of.h>
+#include <linux/of_graph.h>
#include <linux/acpi.h>
#include <linux/pinctrl/consumer.h>
#include <linux/reset.h>
@@ -84,7 +85,7 @@ static int dwc3_get_dr_mode(struct dwc3 *dwc)
* mode. If the controller supports DRD but the dr_mode is not
* specified or set to OTG, then set the mode to peripheral.
*/
- if (mode == USB_DR_MODE_OTG &&
+ if (mode == USB_DR_MODE_OTG && !dwc->edev &&
(!IS_ENABLED(CONFIG_USB_ROLE_SWITCH) ||
!device_property_read_bool(dwc->dev, "usb-role-switch")) &&
!DWC3_VER_IS_PRIOR(DWC3, 330A))
@@ -1462,6 +1463,51 @@ static void dwc3_check_params(struct dwc3 *dwc)
}
}
+static struct extcon_dev *dwc3_get_extcon(struct dwc3 *dwc)
+{
+ struct device *dev = dwc->dev;
+ struct device_node *np_phy;
+ struct extcon_dev *edev = NULL;
+ const char *name;
+
+ if (device_property_read_bool(dev, "extcon"))
+ return extcon_get_edev_by_phandle(dev, 0);
+
+ /*
+ * Device tree platforms should get extcon via phandle.
+ * On ACPI platforms, we get the name from a device property.
+ * This device property is for kernel internal use only and
+ * is expected to be set by the glue code.
+ */
+ if (device_property_read_string(dev, "linux,extcon-name", &name) == 0) {
+ edev = extcon_get_extcon_dev(name);
+ if (!edev)
+ return ERR_PTR(-EPROBE_DEFER);
+
+ return edev;
+ }
+
+ /*
+ * Try to get an extcon device from the USB PHY controller's "port"
+ * node. Check if it has the "port" node first, to avoid printing the
+ * error message from underlying code, as it's a valid case: extcon
+ * device (and "port" node) may be missing in case of "usb-role-switch"
+ * or OTG mode.
+ */
+ np_phy = of_parse_phandle(dev->of_node, "phys", 0);
+ if (of_graph_is_present(np_phy)) {
+ struct device_node *np_conn;
+
+ np_conn = of_graph_get_remote_node(np_phy, -1, -1);
+ if (np_conn)
+ edev = extcon_find_edev_by_node(np_conn);
+ of_node_put(np_conn);
+ }
+ of_node_put(np_phy);
+
+ return edev;
+}
+
static int dwc3_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
@@ -1561,6 +1607,14 @@ static int dwc3_probe(struct platform_device *pdev)
goto err2;
}
+ dwc->edev = dwc3_get_extcon(dwc);
+ if (IS_ERR(dwc->edev)) {
+ ret = PTR_ERR(dwc->edev);
+ dev_err_probe(dwc->dev, ret, "failed to get extcon");
+
+ goto err3;
+ }
+
ret = dwc3_get_dr_mode(dwc);
if (ret)
goto err3;
diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c
index e2b68bb770d1..9a414edc439a 100644
--- a/drivers/usb/dwc3/drd.c
+++ b/drivers/usb/dwc3/drd.c
@@ -8,7 +8,6 @@
*/
#include <linux/extcon.h>
-#include <linux/of_graph.h>
#include <linux/platform_device.h>
#include <linux/property.h>
@@ -438,51 +437,6 @@ static int dwc3_drd_notifier(struct notifier_block *nb,
return NOTIFY_DONE;
}
-static struct extcon_dev *dwc3_get_extcon(struct dwc3 *dwc)
-{
- struct device *dev = dwc->dev;
- struct device_node *np_phy;
- struct extcon_dev *edev = NULL;
- const char *name;
-
- if (device_property_read_bool(dev, "extcon"))
- return extcon_get_edev_by_phandle(dev, 0);
-
- /*
- * Device tree platforms should get extcon via phandle.
- * On ACPI platforms, we get the name from a device property.
- * This device property is for kernel internal use only and
- * is expected to be set by the glue code.
- */
- if (device_property_read_string(dev, "linux,extcon-name", &name) == 0) {
- edev = extcon_get_extcon_dev(name);
- if (!edev)
- return ERR_PTR(-EPROBE_DEFER);
-
- return edev;
- }
-
- /*
- * Try to get an extcon device from the USB PHY controller's "port"
- * node. Check if it has the "port" node first, to avoid printing the
- * error message from underlying code, as it's a valid case: extcon
- * device (and "port" node) may be missing in case of "usb-role-switch"
- * or OTG mode.
- */
- np_phy = of_parse_phandle(dev->of_node, "phys", 0);
- if (of_graph_is_present(np_phy)) {
- struct device_node *np_conn;
-
- np_conn = of_graph_get_remote_node(np_phy, -1, -1);
- if (np_conn)
- edev = extcon_find_edev_by_node(np_conn);
- of_node_put(np_conn);
- }
- of_node_put(np_phy);
-
- return edev;
-}
-
#if IS_ENABLED(CONFIG_USB_ROLE_SWITCH)
#define ROLE_SWITCH 1
static int dwc3_usb_role_switch_set(struct usb_role_switch *sw,
@@ -575,10 +529,6 @@ int dwc3_drd_init(struct dwc3 *dwc)
{
int ret, irq;
- dwc->edev = dwc3_get_extcon(dwc);
- if (IS_ERR(dwc->edev))
- return PTR_ERR(dwc->edev);
-
if (ROLE_SWITCH &&
device_property_read_bool(dwc->dev, "usb-role-switch")) {
ret = dwc3_setup_role_switch(dwc);
--
2.25.1
On Mon, Feb 21, 2022 at 11:20:20AM -0800, Andrey Smirnov wrote:
> If the extcon device exists, get the mode from the extcon device. If
> the controller is DRD and the driver is unable to determine the mode,
> only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
>
> Cc: Felipe Balbi <[email protected]>
> Cc: Thinh Nguyen <[email protected]>
> Cc: [email protected]
> Cc: [email protected]
> Reviewed-by: Thinh Nguyen <[email protected]>
> Signed-off-by: Andrey Smirnov <[email protected]>
> ---
>
> v1 of the patch:
>
> https://lore.kernel.org/linux-usb/[email protected]/T/#u
>
> previons discussion:
>
> https://lore.kernel.org/linux-usb/[email protected]/
>
You forgot to say what changed in this version.
thanks,
greg k-h
Hi,
Andrey Smirnov wrote:
> If the extcon device exists, get the mode from the extcon device. If
> the controller is DRD and the driver is unable to determine the mode,
> only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
>
> Cc: Felipe Balbi <[email protected]>
> Cc: Thinh Nguyen <[email protected]>
> Cc: [email protected]
> Cc: [email protected]
> Reviewed-by: Thinh Nguyen <[email protected]>
> Signed-off-by: Andrey Smirnov <[email protected]>
> ---
>
> v1 of the patch:
>
> https://urldefense.com/v3/__https://lore.kernel.org/linux-usb/[email protected]/T/*u__;Iw!!A4F2R9G_pg!MkC0ZJrDw6TYoTkd6CcnR0EBo8D-uvDlqJDRFdaR82BX-16j0ydzGz0FJR4z4VQtdKhZ$
>
> previons discussion:
>
> https://urldefense.com/v3/__https://lore.kernel.org/linux-usb/[email protected]/__;!!A4F2R9G_pg!MkC0ZJrDw6TYoTkd6CcnR0EBo8D-uvDlqJDRFdaR82BX-16j0ydzGz0FJR4z4Syxv17D$
>
>
> drivers/usb/dwc3/core.c | 56 ++++++++++++++++++++++++++++++++++++++++-
> drivers/usb/dwc3/drd.c | 50 ------------------------------------
> 2 files changed, 55 insertions(+), 51 deletions(-)
>
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index f2448d0a9d39..09f283288ce7 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -23,6 +23,7 @@
> #include <linux/delay.h>
> #include <linux/dma-mapping.h>
> #include <linux/of.h>
> +#include <linux/of_graph.h>
> #include <linux/acpi.h>
> #include <linux/pinctrl/consumer.h>
> #include <linux/reset.h>
> @@ -84,7 +85,7 @@ static int dwc3_get_dr_mode(struct dwc3 *dwc)
> * mode. If the controller supports DRD but the dr_mode is not
> * specified or set to OTG, then set the mode to peripheral.
> */
> - if (mode == USB_DR_MODE_OTG &&
> + if (mode == USB_DR_MODE_OTG && !dwc->edev &&
> (!IS_ENABLED(CONFIG_USB_ROLE_SWITCH) ||
> !device_property_read_bool(dwc->dev, "usb-role-switch")) &&
> !DWC3_VER_IS_PRIOR(DWC3, 330A))
> @@ -1462,6 +1463,51 @@ static void dwc3_check_params(struct dwc3 *dwc)
> }
> }
>
> +static struct extcon_dev *dwc3_get_extcon(struct dwc3 *dwc)
> +{
> + struct device *dev = dwc->dev;
> + struct device_node *np_phy;
> + struct extcon_dev *edev = NULL;
> + const char *name;
> +
> + if (device_property_read_bool(dev, "extcon"))
> + return extcon_get_edev_by_phandle(dev, 0);
> +
> + /*
> + * Device tree platforms should get extcon via phandle.
> + * On ACPI platforms, we get the name from a device property.
> + * This device property is for kernel internal use only and
> + * is expected to be set by the glue code.
> + */
> + if (device_property_read_string(dev, "linux,extcon-name", &name) == 0) {
> + edev = extcon_get_extcon_dev(name);
> + if (!edev)
> + return ERR_PTR(-EPROBE_DEFER);
> +
> + return edev;
> + }
> +
> + /*
> + * Try to get an extcon device from the USB PHY controller's "port"
> + * node. Check if it has the "port" node first, to avoid printing the
> + * error message from underlying code, as it's a valid case: extcon
> + * device (and "port" node) may be missing in case of "usb-role-switch"
> + * or OTG mode.
> + */
> + np_phy = of_parse_phandle(dev->of_node, "phys", 0);
> + if (of_graph_is_present(np_phy)) {
> + struct device_node *np_conn;
> +
> + np_conn = of_graph_get_remote_node(np_phy, -1, -1);
> + if (np_conn)
> + edev = extcon_find_edev_by_node(np_conn);
> + of_node_put(np_conn);
> + }
> + of_node_put(np_phy);
> +
> + return edev;
> +}
> +
> static int dwc3_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> @@ -1561,6 +1607,14 @@ static int dwc3_probe(struct platform_device *pdev)
> goto err2;
> }
>
> + dwc->edev = dwc3_get_extcon(dwc);
> + if (IS_ERR(dwc->edev)) {
> + ret = PTR_ERR(dwc->edev);
> + dev_err_probe(dwc->dev, ret, "failed to get extcon");
My comment earlier was meant to add "\n" to the error message above, not
adding a new line to the code.
Thanks,
Thinh
> +
> + goto err3;
> + }
> +
> ret = dwc3_get_dr_mode(dwc);
> if (ret)
> goto err3;