The Quartz64 board is built upon Rockchip RK3566.
Rockchip RK3566 has two combo phys.
The first connects USB3 and SATA ctrl1, and the second PCIe lane and SATA
ctrl2.
The second combo phy is hardwired to the PCIe slot, where for the first,
the hardware on the board provides both the USB3 connector and the SATA
connector.
This DT allows the users to switch the combo phy to the SATA connector.
Signed-off-by: Alessandro Carminati <[email protected]>
---
.../dts/rockchip/rk3566-quartz64-a.sata.dts | 839 ++++++++++++++++++
1 file changed, 839 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
new file mode 100644
index 000000000000..6ac21b729be7
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
@@ -0,0 +1,839 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Pine64 RK3566 Quartz64-A Board";
+ compatible = "pine64,quartz64-a", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac1_clkin: external-gmac1-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac1_clkin";
+ #clock-cells = <0>;
+ };
+
+ fan: gpio_fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0
+ 4500 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fan_en_h>;
+ #cooling-cells = <2>;
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-work {
+ label = "work-led";
+ default-state = "off";
+ gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_enable_h>;
+ retain-state-suspended;
+ };
+
+ led-diy {
+ label = "diy-led";
+ default-state = "on";
+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&diy_led_enable_h>;
+ retain-state-suspended;
+ };
+ };
+
+ rk817-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK817";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk817>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk817 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ post-power-on-delay-ms = <100>;
+ power-off-delay-us = <5000000>;
+ reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+
+ spdif_dit: spdif-dit {
+ compatible = "linux,spdif-dit";
+ #sound-dai-cells = <0>;
+ };
+
+ spdif_sound: spdif-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_dit>;
+ };
+ };
+
+ vcc12v_dcin: vcc12v_dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ /* vbus feeds the rk817 usb input.
+ * With no battery attached, also feeds vcc_bat+
+ * via ON/OFF_BAT jumper
+ */
+ vbus: vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_enable_h>;
+ regulator-name = "vcc3v3_pcie_p";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ vcc5v0_usb: vcc5v0_usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ /* all four ports are controlled by one gpio
+ * the host ports are sourced from vcc5v0_usb
+ * the otg port is sourced from vcc5v0_midu
+ */
+ vcc5v0_usb20_host: vcc5v0_usb20_host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb20_host_en>;
+ regulator-name = "vcc5v0_usb20_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+
+ vcc5v0_usb20_otg: vcc5v0_usb20_otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+ regulator-name = "vcc5v0_usb20_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dcdc_boost>;
+ };
+
+ vcc3v3_sd: vcc3v3_sd {
+ compatible = "regulator-fixed";
+ enable-active-low;
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_sd_h>;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ /* sourced from vbus and vcc_bat+ via rk817 sw5 */
+ vcc_sys: vcc_sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ vin-supply = <&vbus>;
+ };
+
+ /* sourced from vcc_sys, sdio module operates internally at 3.3v */
+ vcc_wl: vcc_wl {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_wl";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_thermal {
+ trips {
+ cpu_hot: cpu_hot {
+ temperature = <55000>;
+ hysteresis = <2000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_3v3>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m0_miim
+ &gmac1m0_tx_bus2
+ &gmac1m0_rx_bus2
+ &gmac1m0_rgmii_clk
+ &gmac1m0_clkinout
+ &gmac1m0_rgmii_bus>;
+ snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda_0v9>;
+ avdd-1v8-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&dcdc_boost>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_logic";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_3v3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc2v8_dvp: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc2v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ dcdc_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ otg_switch: OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+/* i2c3 is exposed on con40
+ * pin 3 - i2c3_sda_m0, pullup to vcc_3v3
+ * pin 5 - i2c3_scl_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "okay";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_h>;
+ reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie_p>;
+ status = "okay";
+};
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ bt_wake_l: bt-wake-l {
+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ fan {
+ fan_en_h: fan-en-h {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ work_led_enable_h: work-led-enable-h {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ diy_led_enable_h: diy-led-enable-h {
+ rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_enable_h: pcie-enable-h {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie_reset_h: pcie-reset-h {
+ rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
+ rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ vcc_sd {
+ vcc_sd_h: vcc-sd-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc1v8_dvp>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_wl>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sfc {
+ pinctrl-0 = <&fspi_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+/* spdif is exposed on con40 pin 18 */
+&spdif {
+ status = "okay";
+};
+
+/* spi1 is exposed on con40
+ * pin 11 - spi1_mosi_m1
+ * pin 13 - spi1_miso_m1
+ * pin 15 - spi1_clk_m1
+ * pin 17 - spi1_cs0_m1
+ */
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1m1_cs0 &spi1m1_pins>;
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+/* uart0 is exposed on con40
+ * pin 12 - uart0_tx
+ * pin 14 - uart0_rx
+ */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
+ status = "okay";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rk817 1>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+ vbat-supply = <&vcc_sys>;
+ vddio-supply = <&vcca1v8_pmu>;
+ };
+};
+
+/* uart2 is exposed on con40
+ * pin 8 - uart2_tx_m0_debug
+ * pin 10 - uart2_rx_m0_debug
+ */
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* usb3 controller is muxed with sata1 */
+&sata1 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb20_otg>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.34.1
On 14/09/2022 20:59, Alessandro Carminati wrote:
> The Quartz64 board is built upon Rockchip RK3566.
> Rockchip RK3566 has two combo phys.
> The first connects USB3 and SATA ctrl1, and the second PCIe lane and SATA
> ctrl2.
> The second combo phy is hardwired to the PCIe slot, where for the first,
> the hardware on the board provides both the USB3 connector and the SATA
> connector.
> This DT allows the users to switch the combo phy to the SATA connector.
>
> Signed-off-by: Alessandro Carminati <[email protected]>
> ---
> .../dts/rockchip/rk3566-quartz64-a.sata.dts | 839 ++++++++++++++++++
> 1 file changed, 839 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> new file mode 100644
> index 000000000000..6ac21b729be7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> @@ -0,0 +1,839 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> + model = "Pine64 RK3566 Quartz64-A Board";
> + compatible = "pine64,quartz64-a", "rockchip,rk3566";
> +
> + aliases {
> + ethernet0 = &gmac1;
> + mmc0 = &sdmmc0;
> + mmc1 = &sdhci;
> + };
> +
> + chosen: chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + gmac1_clkin: external-gmac1-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "gmac1_clkin";
> + #clock-cells = <0>;
> + };
> +
> + fan: gpio_fan {
No underscores in node names. Node name just "fan"
> + compatible = "gpio-fan";
> + gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> + gpio-fan,speed-map = <0 0
> + 4500 1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&fan_en_h>;
> + #cooling-cells = <2>;
> + };
> +
> + hdmi-con {
Node name: connector
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-work {
> + label = "work-led";
> + default-state = "off";
> + gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&work_led_enable_h>;
> + retain-state-suspended;
> + };
> +
> + led-diy {
> + label = "diy-led";
> + default-state = "on";
> + gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + pinctrl-names = "default";
> + pinctrl-0 = <&diy_led_enable_h>;
> + retain-state-suspended;
> + };
> + };
> +
> + rk817-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "Analog RK817";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1_8ch>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&rk817>;
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk817 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> + post-power-on-delay-ms = <100>;
> + power-off-delay-us = <5000000>;
> + reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
> + };
> +
> + spdif_dit: spdif-dit {
> + compatible = "linux,spdif-dit";
> + #sound-dai-cells = <0>;
> + };
> +
> + spdif_sound: spdif-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "SPDIF";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&spdif>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&spdif_dit>;
> + };
> + };
> +
> + vcc12v_dcin: vcc12v_dcin {
No underscores in node names, generic node name, so at least with
regulator prefix or suffix.
> + compatible = "regulator-fixed";
> + regulator-name = "vcc12v_dcin";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + /* vbus feeds the rk817 usb input.
> + * With no battery attached, also feeds vcc_bat+
> + * via ON/OFF_BAT jumper
> + */
> + vbus: vbus {
Ditto
> + compatible = "regulator-fixed";
> + regulator-name = "vbus";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
> +
> + vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
And here you have suffix...
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_enable_h>;
> + regulator-name = "vcc3v3_pcie_p";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_3v3>;
> + };
> +
> + vcc5v0_usb: vcc5v0_usb {
Ditto
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_usb";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
> +
> + /* all four ports are controlled by one gpio
> + * the host ports are sourced from vcc5v0_usb
> + * the otg port is sourced from vcc5v0_midu
> + */
> + vcc5v0_usb20_host: vcc5v0_usb20_host {
and in other places as well
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_usb20_host_en>;
> + regulator-name = "vcc5v0_usb20_host";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v0_usb>;
> + };
> +
> + vcc5v0_usb20_otg: vcc5v0_usb20_otg {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
> + regulator-name = "vcc5v0_usb20_otg";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dcdc_boost>;
> + };
> +
> + vcc3v3_sd: vcc3v3_sd {
> + compatible = "regulator-fixed";
> + enable-active-low;
> + gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc_sd_h>;
> + regulator-boot-on;
> + regulator-name = "vcc3v3_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_3v3>;
> + };
> +
> + /* sourced from vbus and vcc_bat+ via rk817 sw5 */
> + vcc_sys: vcc_sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <4400000>;
> + regulator-max-microvolt = <4400000>;
> + vin-supply = <&vbus>;
> + };
> +
> + /* sourced from vcc_sys, sdio module operates internally at 3.3v */
> + vcc_wl: vcc_wl {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_wl";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sys>;
> + };
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&combphy2 {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu_thermal {
> + trips {
> + cpu_hot: cpu_hot {
No underscores in node names. Are you sure bindings/schema do not expect
some specific name?
> + temperature = <55000>;
> + hysteresis = <2000>;
> + type = "active";
> + };
> + };
Best regards,
Krzysztof
Hello, I'm reviewing the notes you made me on the review.
To tell all the truth, I derived the DTS from an existing one by modifying a small portion of it.
In the end, your notes are for the already existing DTS.
To address the notes in your message and spare future work, I decided to refactor the rk3566-quartz64-a DTS.
I will post another patch briefly with the new version.
For the moment, thank you for the review.
Regards
Alessandro
On Thu, Sep 15, 2022 at 04:07:54PM +0100, Krzysztof Kozlowski wrote:
> On 14/09/2022 20:59, Alessandro Carminati wrote:
> > The Quartz64 board is built upon Rockchip RK3566.
> > Rockchip RK3566 has two combo phys.
> > The first connects USB3 and SATA ctrl1, and the second PCIe lane and SATA
> > ctrl2.
> > The second combo phy is hardwired to the PCIe slot, where for the first,
> > the hardware on the board provides both the USB3 connector and the SATA
> > connector.
> > This DT allows the users to switch the combo phy to the SATA connector.
> >
> > Signed-off-by: Alessandro Carminati <[email protected]>
> > ---
> > .../dts/rockchip/rk3566-quartz64-a.sata.dts | 839 ++++++++++++++++++
> > 1 file changed, 839 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> > new file mode 100644
> > index 000000000000..6ac21b729be7
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.sata.dts
> > @@ -0,0 +1,839 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/pinctrl/rockchip.h>
> > +#include <dt-bindings/soc/rockchip,vop2.h>
> > +#include "rk3566.dtsi"
> > +
> > +/ {
> > + model = "Pine64 RK3566 Quartz64-A Board";
> > + compatible = "pine64,quartz64-a", "rockchip,rk3566";
> > +
> > + aliases {
> > + ethernet0 = &gmac1;
> > + mmc0 = &sdmmc0;
> > + mmc1 = &sdhci;
> > + };
> > +
> > + chosen: chosen {
> > + stdout-path = "serial2:1500000n8";
> > + };
> > +
> > + gmac1_clkin: external-gmac1-clock {
> > + compatible = "fixed-clock";
> > + clock-frequency = <125000000>;
> > + clock-output-names = "gmac1_clkin";
> > + #clock-cells = <0>;
> > + };
> > +
> > + fan: gpio_fan {
>
> No underscores in node names. Node name just "fan"
>
> > + compatible = "gpio-fan";
> > + gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> > + gpio-fan,speed-map = <0 0
> > + 4500 1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&fan_en_h>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + hdmi-con {
>
> Node name: connector
>
> > + compatible = "hdmi-connector";
> > + type = "a";
> > +
> > + port {
> > + hdmi_con_in: endpoint {
> > + remote-endpoint = <&hdmi_out_con>;
> > + };
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + led-work {
> > + label = "work-led";
> > + default-state = "off";
> > + gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&work_led_enable_h>;
> > + retain-state-suspended;
> > + };
> > +
> > + led-diy {
> > + label = "diy-led";
> > + default-state = "on";
> > + gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&diy_led_enable_h>;
> > + retain-state-suspended;
> > + };
> > + };
> > +
> > + rk817-sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,name = "Analog RK817";
> > + simple-audio-card,mclk-fs = <256>;
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&i2s1_8ch>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&rk817>;
> > + };
> > + };
> > +
> > + sdio_pwrseq: sdio-pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + clocks = <&rk817 1>;
> > + clock-names = "ext_clock";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&wifi_enable_h>;
> > + post-power-on-delay-ms = <100>;
> > + power-off-delay-us = <5000000>;
> > + reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + spdif_dit: spdif-dit {
> > + compatible = "linux,spdif-dit";
> > + #sound-dai-cells = <0>;
> > + };
> > +
> > + spdif_sound: spdif-sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,name = "SPDIF";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&spdif>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&spdif_dit>;
> > + };
> > + };
> > +
> > + vcc12v_dcin: vcc12v_dcin {
>
> No underscores in node names, generic node name, so at least with
> regulator prefix or suffix.
>
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc12v_dcin";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <12000000>;
> > + regulator-max-microvolt = <12000000>;
> > + };
> > +
> > + /* vbus feeds the rk817 usb input.
> > + * With no battery attached, also feeds vcc_bat+
> > + * via ON/OFF_BAT jumper
> > + */
> > + vbus: vbus {
>
> Ditto
>
> > + compatible = "regulator-fixed";
> > + regulator-name = "vbus";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + vin-supply = <&vcc12v_dcin>;
> > + };
> > +
> > + vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
>
> And here you have suffix...
>
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pcie_enable_h>;
> > + regulator-name = "vcc3v3_pcie_p";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vcc_3v3>;
> > + };
> > +
> > + vcc5v0_usb: vcc5v0_usb {
>
> Ditto
>
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc5v0_usb";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + vin-supply = <&vcc12v_dcin>;
> > + };
> > +
> > + /* all four ports are controlled by one gpio
> > + * the host ports are sourced from vcc5v0_usb
> > + * the otg port is sourced from vcc5v0_midu
> > + */
> > + vcc5v0_usb20_host: vcc5v0_usb20_host {
>
> and in other places as well
>
>
>
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vcc5v0_usb20_host_en>;
> > + regulator-name = "vcc5v0_usb20_host";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + vin-supply = <&vcc5v0_usb>;
> > + };
> > +
> > + vcc5v0_usb20_otg: vcc5v0_usb20_otg {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
> > + regulator-name = "vcc5v0_usb20_otg";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + vin-supply = <&dcdc_boost>;
> > + };
> > +
> > + vcc3v3_sd: vcc3v3_sd {
> > + compatible = "regulator-fixed";
> > + enable-active-low;
> > + gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vcc_sd_h>;
> > + regulator-boot-on;
> > + regulator-name = "vcc3v3_sd";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vcc_3v3>;
> > + };
> > +
> > + /* sourced from vbus and vcc_bat+ via rk817 sw5 */
> > + vcc_sys: vcc_sys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc_sys";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <4400000>;
> > + regulator-max-microvolt = <4400000>;
> > + vin-supply = <&vbus>;
> > + };
> > +
> > + /* sourced from vcc_sys, sdio module operates internally at 3.3v */
> > + vcc_wl: vcc_wl {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc_wl";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vcc_sys>;
> > + };
> > +};
> > +
> > +&combphy1 {
> > + status = "okay";
> > +};
> > +
> > +&combphy2 {
> > + status = "okay";
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <&vdd_cpu>;
> > +};
> > +
> > +&cpu1 {
> > + cpu-supply = <&vdd_cpu>;
> > +};
> > +
> > +&cpu2 {
> > + cpu-supply = <&vdd_cpu>;
> > +};
> > +
> > +&cpu3 {
> > + cpu-supply = <&vdd_cpu>;
> > +};
> > +
> > +&cpu_thermal {
> > + trips {
> > + cpu_hot: cpu_hot {
>
> No underscores in node names. Are you sure bindings/schema do not expect
> some specific name?
>
> > + temperature = <55000>;
> > + hysteresis = <2000>;
> > + type = "active";
> > + };
> > + };
>
>
> Best regards,
> Krzysztof