Combined sequence currently forces cmd and addr transfers in X1.
Check nbits for CMD and ADDR xfers and update config registers.
Signed-off-by: Krishna Yarlagadda <[email protected]>
---
drivers/spi/spi-tegra210-quad.c | 12 ++++--------
1 file changed, 4 insertions(+), 8 deletions(-)
diff --git a/drivers/spi/spi-tegra210-quad.c b/drivers/spi/spi-tegra210-quad.c
index 06bf19d0cfc1..be11daafb7d4 100644
--- a/drivers/spi/spi-tegra210-quad.c
+++ b/drivers/spi/spi-tegra210-quad.c
@@ -135,7 +135,7 @@
#define QSPI_COMMAND_VALUE_SET(X) (((x) & 0xFF) << 0)
#define QSPI_CMB_SEQ_CMD_CFG 0x1a0
-#define QSPI_COMMAND_X1_X2_X4(x) (((x) & 0x3) << 13)
+#define QSPI_COMMAND_X1_X2_X4(x) ((((x) >> 1) & 0x3) << 13)
#define QSPI_COMMAND_X1_X2_X4_MASK (0x03 << 13)
#define QSPI_COMMAND_SDR_DDR BIT(12)
#define QSPI_COMMAND_SIZE_SET(x) (((x) & 0xFF) << 0)
@@ -147,7 +147,7 @@
#define QSPI_ADDRESS_VALUE_SET(X) (((x) & 0xFFFF) << 0)
#define QSPI_CMB_SEQ_ADDR_CFG 0x1ac
-#define QSPI_ADDRESS_X1_X2_X4(x) (((x) & 0x3) << 13)
+#define QSPI_ADDRESS_X1_X2_X4(x) ((((x) >> 1) & 0x3) << 13)
#define QSPI_ADDRESS_X1_X2_X4_MASK (0x03 << 13)
#define QSPI_ADDRESS_SDR_DDR BIT(12)
#define QSPI_ADDRESS_SIZE_SET(x) (((x) & 0xFF) << 0)
@@ -1029,10 +1029,6 @@ static u32 tegra_qspi_addr_config(bool is_ddr, u8 bus_width, u8 len)
{
u32 addr_config = 0;
- /* Extract Address configuration and value */
- is_ddr = 0; //Only SDR mode supported
- bus_width = 0; //X1 mode
-
if (is_ddr)
addr_config |= QSPI_ADDRESS_SDR_DDR;
else
@@ -1066,13 +1062,13 @@ static int tegra_qspi_combined_seq_xfer(struct tegra_qspi *tqspi,
switch (transfer_phase) {
case CMD_TRANSFER:
/* X1 SDR mode */
- cmd_config = tegra_qspi_cmd_config(false, 0,
+ cmd_config = tegra_qspi_cmd_config(false, xfer->tx_nbits,
xfer->len);
cmd_value = *((const u8 *)(xfer->tx_buf));
break;
case ADDR_TRANSFER:
/* X1 SDR mode */
- addr_config = tegra_qspi_addr_config(false, 0,
+ addr_config = tegra_qspi_addr_config(false, xfer->tx_nbits,
xfer->len);
address_value = *((const u32 *)(xfer->tx_buf));
break;
--
2.17.1
On Sat, Oct 01, 2022 at 05:51:46PM +0530, Krishna Yarlagadda wrote:
> Combined sequence currently forces cmd and addr transfers in X1.
> Check nbits for CMD and ADDR xfers and update config registers.
I can't tell from this commit message what this change is supposed to
do or even if it's a fix.