Add a new driver for the TouchNetix's axiom family of touchscreen
controller. This driver only support i2c and can be later adapted for
SPI and USB support.
--
Changes in v13:
- Fix CRC16 not selected reported in:https://lore.kernel.org/oe-kbuild-all/[email protected]/
- Rebase on v6.10-rc2
Changes in v12:
- Fix REGMAP_I2C not selected
- Rebase on v6.10-rc1
Changes in v11:
- Fix regulators name to match dt-binding
- Enable regulators before reset is asserted
Changes in v10:
- Set regulators as required
- Enable power supply before reset
- Fix ref count due to regulator requested twice
- Rebase on v6.9-rc4
Changes in v9:
- Fix issue reported in https://lore.kernel.org/oe-kbuild-all/[email protected]/
- Rebase on v6.8-rc2
Changes in v8:
- Fix missing call to input_report_slot_state()
- Fix issue reported in https://lore.kernel.org/oe-kbuild-all/[email protected]/
Changes in v7:
- Remove startup time from dt-binding
- Fix usage table not correctly populated
Changes in v6:
- Fix missing unevaluatedProperties.in dt-binding
- Use __le16 to correctly deal with device endianness
- Use standart kernel types s/char/u8/
- Use regmap api as driver might support spi later
- Use get_unaligned_le16() for the sake of clarity
- Use devm_regulator_enable_optional()
Changes in v5:
- Fix wrong message constructed in axiom_i2c_read
- Delay required between i2c reads is >= 250us
- Do not split report reading in two phases as we'll
have to wait 500us
- Use lower-case in properties names
- Make regulators properties are required in dt-binding
- Fix bug report: https://lore.kernel.org/lkml/[email protected]/
- Fix bug report: https://lore.kernel.org/lkml/[email protected]/
Changes in v4:
- Cleanup unused headers and macros
- Use standard kernel type
- Namespace structures and functions
- Use packed struct when possible to avoid bitfield operators
- Fix missing break when address is found in axiom_populate_target_address()
- Split reads in two steps for the reports, first length then report
itself so we only read required bytes
- Get poll-interval from devicetree
- Add VDDI/VDDA regulators
- Add a startup delay of 110 ms required after VDDA/VDDI is applied
- Remove axiom_i2c_write() as it is no more used
Changes in v3:
- Remove irq-gpios property in dt-binding
- Use a generic node name
- Fix issues reported in https://lore.kernel.org/oe-kbuild-all/[email protected]/
Changes in v2:
- Add device tree binding documentation
- Move core functions in axiom_i2c as we only care about i2c support now
- Use static function when required
- Use syntax dev_err_probe()
- Add an hardware based reset
Kamel Bouhara (3):
dt-bindings: vendor-prefixes: Add TouchNetix AS
dt-bindings: input: Add TouchNetix axiom touchscreen
Input: Add TouchNetix axiom i2c touchscreen driver
.../input/touchscreen/touchnetix,ax54a.yaml | 62 ++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 8 +
drivers/input/touchscreen/Kconfig | 14 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/touchnetix_axiom.c | 657 ++++++++++++++++++
6 files changed, 744 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/touchnetix,ax54a.yaml
create mode 100644 drivers/input/touchscreen/touchnetix_axiom.c
--
2.25.1
Add vendor prefix for TouchNetix AS (https://www.touchnetix.com/products/).
Signed-off-by: Kamel Bouhara <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index fbf47f0bacf1..f102b3abf3fc 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1489,6 +1489,8 @@ patternProperties:
description: Toradex AG
"^toshiba,.*":
description: Toshiba Corporation
+ "^touchnetix,.*":
+ description: TouchNetix AS
"^toumaz,.*":
description: Toumaz
"^tpk,.*":
--
2.25.1
Add a new driver for the TouchNetix's axiom family of
touchscreen controllers. This driver only supports i2c
and can be later adapted for SPI and USB support.
Signed-off-by: Kamel Bouhara <[email protected]>
---
MAINTAINERS | 2 +
drivers/input/touchscreen/Kconfig | 14 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/touchnetix_axiom.c | 657 +++++++++++++++++++
4 files changed, 674 insertions(+)
create mode 100644 drivers/input/touchscreen/touchnetix_axiom.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 225309db4110..a3ece12e32d7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22744,9 +22744,11 @@ F: drivers/platform/x86/toshiba-wmi.c
TOUCHNETIX AXIOM I2C TOUCHSCREEN DRIVER
M: Kamel Bouhara <[email protected]>
+M: [email protected]
L: [email protected]
S: Maintained
F: Documentation/devicetree/bindings/input/touchscreen/touchnetix,ax54a.yaml
+F: drivers/input/touchscreen/touchnetix_axiom.c
TPM DEVICE DRIVER
M: Peter Huewe <[email protected]>
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index c821fe3ee794..1ce8f1c25625 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -834,6 +834,20 @@ config TOUCHSCREEN_MIGOR
To compile this driver as a module, choose M here: the
module will be called migor_ts.
+config TOUCHSCREEN_TOUCHNETIX_AXIOM
+ tristate "TouchNetix AXIOM based touchscreen controllers"
+ depends on I2C
+ select CRC16
+ select REGMAP_I2C
+ help
+ Say Y here if you have a axiom touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called axiom.
+
config TOUCHSCREEN_TOUCHRIGHT
tristate "Touchright serial touchscreen"
select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index a81cb5aa21a5..6ce7b804adc7 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -91,6 +91,7 @@ obj-$(CONFIG_TOUCHSCREEN_SUR40) += sur40.o
obj-$(CONFIG_TOUCHSCREEN_SURFACE3_SPI) += surface3_spi.o
obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
+obj-$(CONFIG_TOUCHSCREEN_TOUCHNETIX_AXIOM) += touchnetix_axiom.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
obj-$(CONFIG_TOUCHSCREEN_TS4800) += ts4800-ts.o
diff --git a/drivers/input/touchscreen/touchnetix_axiom.c b/drivers/input/touchscreen/touchnetix_axiom.c
new file mode 100644
index 000000000000..09550847392e
--- /dev/null
+++ b/drivers/input/touchscreen/touchnetix_axiom.c
@@ -0,0 +1,657 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * TouchNetix axiom Touchscreen Driver
+ *
+ * Copyright (C) 2020-2023 TouchNetix Ltd.
+ *
+ * Author(s): Bart Prescott <[email protected]>
+ * Pedro Torruella <[email protected]>
+ * Mark Satterthwaite <[email protected]>
+ * Hannah Rossiter <[email protected]>
+ * Kamel Bouhara <[email protected]>
+ *
+ */
+#include <linux/bitfield.h>
+#include <linux/crc16.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/regmap.h>
+
+#include <asm/unaligned.h>
+#define AXIOM_PROX_LEVEL -128
+#define AXIOM_DMA_OPS_DELAY_USEC 250
+#define AXIOM_STARTUP_TIME_MS 110
+/*
+ * Register group u31 has 2 pages for usage table entries.
+ */
+#define AXIOM_U31_MAX_USAGES 0xff
+#define AXIOM_U31_BYTES_PER_USAGE 6
+#define AXIOM_U31_PAGE0_LENGTH 0x0C
+#define AXIOM_U31_BOOTMODE_MASK BIT(7)
+#define AXIOM_U31_DEVID_MASK GENMASK(14, 0)
+
+#define AXIOM_MAX_REPORT_LEN 0x7f
+
+#define AXIOM_CMD_HEADER_READ_MASK BIT(15)
+#define AXIOM_U41_MAX_TARGETS 10
+
+#define AXIOM_U46_AUX_CHANNELS 4
+#define AXIOM_U46_AUX_MASK GENMASK(11, 0)
+
+#define AXIOM_COMMS_MAX_USAGE_PAGES 3
+#define AXIOM_COMMS_PAGE_SIZE 256
+#define AXIOM_COMMS_REPORT_LEN_MASK GENMASK(6, 0)
+
+#define AXIOM_REPORT_USAGE_ID 0x34
+#define AXIOM_DEVINFO_USAGE_ID 0x31
+#define AXIOM_USAGE_2HB_REPORT_ID 0x01
+#define AXIOM_USAGE_2AUX_REPORT_ID 0x46
+#define AXIOM_USAGE_2DCTS_REPORT_ID 0x41
+
+#define AXIOM_PAGE_OFFSET_MASK GENMASK(6, 0)
+
+struct axiom_devinfo {
+ __le16 device_id;
+ u8 fw_minor;
+ u8 fw_major;
+ u8 fw_info_extra;
+ u8 tcp_revision;
+ u8 bootloader_fw_minor;
+ u8 bootloader_fw_major;
+ __le16 jedec_id;
+ u8 num_usages;
+} __packed;
+
+/*
+ * Describes parameters of a specific usage, essentially a single element of
+ * the "Usage Table"
+ */
+struct axiom_usage_entry {
+ u8 id;
+ u8 is_report;
+ u8 start_page;
+ u8 num_pages;
+};
+
+/*
+ * Represents state of a touch or target when detected prior to a touch (eg.
+ * hover or proximity events).
+ */
+enum axiom_target_state {
+ AXIOM_TARGET_STATE_NOT_PRESENT = 0,
+ AXIOM_TARGET_STATE_PROX = 1,
+ AXIOM_TARGET_STATE_HOVER = 2,
+ AXIOM_TARGET_STATE_TOUCHING = 3,
+};
+
+struct axiom_u41_target {
+ enum axiom_target_state state;
+ u16 x;
+ u16 y;
+ s8 z;
+ bool insert;
+ bool touch;
+};
+
+struct axiom_target_report {
+ u8 index;
+ u8 present;
+ u16 x;
+ u16 y;
+ s8 z;
+};
+
+struct axiom_cmd_header {
+ __le16 target_address;
+ __le16 length;
+} __packed;
+
+struct axiom_data {
+ struct axiom_devinfo devinfo;
+ struct device *dev;
+ struct gpio_desc *reset_gpio;
+ struct i2c_client *client;
+ struct input_dev *input_dev;
+ u32 max_report_len;
+ u8 rx_buf[AXIOM_COMMS_MAX_USAGE_PAGES * AXIOM_COMMS_PAGE_SIZE];
+ struct axiom_u41_target targets[AXIOM_U41_MAX_TARGETS];
+ struct axiom_usage_entry usage_table[AXIOM_U31_MAX_USAGES];
+ bool usage_table_populated;
+ struct regmap *regmap;
+ struct touchscreen_properties prop;
+};
+
+static const struct regmap_config axiom_i2c_regmap_config = {
+ .reg_bits = 32,
+ .reg_format_endian = REGMAP_ENDIAN_LITTLE,
+ .val_bits = 8,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+/*
+ * axiom devices are typically configured to report touches at a rate
+ * of 100Hz (10ms) for systems that require polling for reports.
+ * When reports are polled, it will be expected to occasionally
+ * observe the overflow bit being set in the reports.
+ * This indicates that reports are not being read fast enough.
+ */
+#define POLL_INTERVAL_DEFAULT_MS 10
+
+/* Translate usage/page/offset triplet into physical address. */
+static u16 axiom_usage_to_target_address(struct axiom_data *ts, u8 usage, u8 page,
+ char offset)
+{
+ /* At the moment the convention is that u31 is always at physical address 0x0 */
+ if (!ts->usage_table_populated) {
+ if (usage == AXIOM_DEVINFO_USAGE_ID)
+ return ((page << 8) + offset);
+ else
+ return 0xffff;
+ }
+
+ if (page >= ts->usage_table[usage].num_pages) {
+ dev_err(ts->dev, "Invalid usage table! usage: u%02x, page: %02x, offset: %02x\n",
+ usage, page, offset);
+ return 0xffff;
+ }
+
+ return ((ts->usage_table[usage].start_page + page) << 8) + offset;
+}
+
+static int axiom_read(struct axiom_data *ts, u8 usage, u8 page, void *buf, u16 len)
+{
+ struct axiom_cmd_header cmd_header;
+ u32 preamble;
+ int ret;
+
+ cmd_header.target_address = cpu_to_le16(axiom_usage_to_target_address(ts, usage, page, 0));
+ cmd_header.length = cpu_to_le16(len | AXIOM_CMD_HEADER_READ_MASK);
+
+ preamble = get_unaligned_le32(&cmd_header);
+
+ ret = regmap_write(ts->regmap, preamble, 0);
+ if (ret) {
+ dev_err(ts->dev, "failed to write preamble, error %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_raw_read(ts->regmap, 0, buf, len);
+ if (ret) {
+ dev_err(ts->dev, "failed to read target address %04x, error %d\n",
+ cmd_header.target_address, ret);
+ return ret;
+ }
+
+ /* Wait device's DMA operations */
+ usleep_range(AXIOM_DMA_OPS_DELAY_USEC, AXIOM_DMA_OPS_DELAY_USEC + 50);
+
+ return 0;
+}
+
+/*
+ * One of the main purposes for reading the usage table is to identify
+ * which usages reside at which target address.
+ * When performing subsequent reads or writes to AXIOM, the target address
+ * is used to specify which usage is being accessed.
+ * Consider the following discovery code which will build up the usage table.
+ */
+static u32 axiom_populate_usage_table(struct axiom_data *ts)
+{
+ struct axiom_usage_entry *usage_table;
+ u8 *rx_data = ts->rx_buf;
+ u32 max_report_len = 0;
+ u32 usage_id;
+ int error;
+
+ usage_table = ts->usage_table;
+
+ /* Read the second page of usage u31 to get the usage table */
+ error = axiom_read(ts, AXIOM_DEVINFO_USAGE_ID, 1, rx_data,
+ (AXIOM_U31_BYTES_PER_USAGE * ts->devinfo.num_usages));
+
+ if (error)
+ return error;
+
+ for (usage_id = 0; usage_id < ts->devinfo.num_usages; usage_id++) {
+ u16 offset = (usage_id * AXIOM_U31_BYTES_PER_USAGE);
+ u8 id = rx_data[offset + 0];
+ u8 start_page = rx_data[offset + 1];
+ u8 num_pages = rx_data[offset + 2];
+ u32 max_offset = ((rx_data[offset + 3] & AXIOM_PAGE_OFFSET_MASK) + 1) * 2;
+
+ usage_table[id].is_report = !num_pages;
+
+ /* Store the entry into the usage table */
+ usage_table[id].id = id;
+ usage_table[id].start_page = start_page;
+ usage_table[id].num_pages = num_pages;
+
+ dev_dbg(ts->dev, "Usage u%02x Info: %*ph\n", id, AXIOM_U31_BYTES_PER_USAGE,
+ &rx_data[offset]);
+
+ /* Identify the max report length the module will receive */
+ if (usage_table[id].is_report && max_offset > max_report_len)
+ max_report_len = max_offset;
+ }
+
+ ts->usage_table_populated = true;
+
+ return max_report_len;
+}
+
+static int axiom_discover(struct axiom_data *ts)
+{
+ int error;
+
+ /*
+ * Fetch the first page of usage u31 to get the
+ * device information and the number of usages
+ */
+ error = axiom_read(ts, AXIOM_DEVINFO_USAGE_ID, 0, &ts->devinfo, AXIOM_U31_PAGE0_LENGTH);
+ if (error)
+ return error;
+
+ dev_dbg(ts->dev, " Boot Mode : %s\n",
+ FIELD_GET(AXIOM_U31_BOOTMODE_MASK,
+ le16_to_cpu(ts->devinfo.device_id)) ? "BLP" : "TCP");
+ dev_dbg(ts->dev, " Device ID : %04lx\n",
+ FIELD_GET(AXIOM_U31_DEVID_MASK, le16_to_cpu(ts->devinfo.device_id)));
+ dev_dbg(ts->dev, " Firmware Rev : %02x.%02x\n", ts->devinfo.fw_major,
+ ts->devinfo.fw_minor);
+ dev_dbg(ts->dev, " Bootloader Rev : %02x.%02x\n", ts->devinfo.bootloader_fw_major,
+ ts->devinfo.bootloader_fw_minor);
+ dev_dbg(ts->dev, " FW Extra Info : %04x\n", ts->devinfo.fw_info_extra);
+ dev_dbg(ts->dev, " Silicon : %04x\n", le16_to_cpu(ts->devinfo.jedec_id));
+ dev_dbg(ts->dev, " Number usages : %04x\n", ts->devinfo.num_usages);
+
+ ts->max_report_len = axiom_populate_usage_table(ts);
+ if (!ts->max_report_len || !ts->devinfo.num_usages ||
+ ts->max_report_len > AXIOM_MAX_REPORT_LEN) {
+ dev_err(ts->dev, "Invalid report length or usages number");
+ return -EINVAL;
+ }
+
+ dev_dbg(ts->dev, "Max Report Length: %u\n", ts->max_report_len);
+
+ return 0;
+}
+
+/*
+ * Support function to axiom_process_u41_report.
+ * Generates input-subsystem events for every target.
+ * After calling this function the caller shall issue
+ * a Sync to the input sub-system.
+ */
+static bool axiom_process_u41_report_target(struct axiom_data *ts,
+ struct axiom_target_report *target)
+{
+ struct input_dev *input_dev = ts->input_dev;
+ struct axiom_u41_target *target_prev_state;
+ enum axiom_target_state current_state;
+ int id;
+
+ /* Verify the target index */
+ if (target->index >= AXIOM_U41_MAX_TARGETS) {
+ dev_err(ts->dev, "Invalid target index! %u\n", target->index);
+ return false;
+ }
+
+ target_prev_state = &ts->targets[target->index];
+
+ current_state = AXIOM_TARGET_STATE_NOT_PRESENT;
+
+ if (target->present) {
+ if (target->z >= 0)
+ current_state = AXIOM_TARGET_STATE_TOUCHING;
+ else if (target->z > AXIOM_PROX_LEVEL && target->z < 0)
+ current_state = AXIOM_TARGET_STATE_HOVER;
+ else if (target->z == AXIOM_PROX_LEVEL)
+ current_state = AXIOM_TARGET_STATE_PROX;
+ }
+
+ if (target_prev_state->state == current_state &&
+ target_prev_state->x == target->x &&
+ target_prev_state->y == target->y &&
+ target_prev_state->z == target->z)
+ return false;
+
+ id = target->index;
+
+ dev_dbg(ts->dev, "U41 Target T%u, present:%u, x:%u, y:%u, z:%d\n",
+ target->index, target->present,
+ target->x, target->y, target->z);
+
+ switch (current_state) {
+ case AXIOM_TARGET_STATE_NOT_PRESENT:
+ case AXIOM_TARGET_STATE_PROX:
+ if (!target_prev_state->insert)
+ break;
+ target_prev_state->insert = false;
+
+ if (!id)
+ input_report_key(input_dev, BTN_TOUCH, 0);
+
+ input_mt_report_slot_inactive(input_dev);
+ /*
+ * make sure the previous coordinates are
+ * all off screen when the finger comes back
+ */
+ target->x = 65535;
+ target->y = 65535;
+ target->z = AXIOM_PROX_LEVEL;
+ break;
+ case AXIOM_TARGET_STATE_HOVER:
+ case AXIOM_TARGET_STATE_TOUCHING:
+ target_prev_state->insert = true;
+ input_report_abs(input_dev, ABS_MT_TRACKING_ID, id);
+ input_report_abs(input_dev, ABS_MT_POSITION_X, target->x);
+ input_report_abs(input_dev, ABS_MT_POSITION_Y, target->y);
+
+ if (current_state == AXIOM_TARGET_STATE_TOUCHING) {
+ input_report_abs(input_dev, ABS_MT_DISTANCE, 0);
+ input_report_abs(input_dev, ABS_DISTANCE, 0);
+ input_report_abs(input_dev, ABS_MT_PRESSURE, target->z);
+ input_report_abs(input_dev, ABS_PRESSURE, target->z);
+ } else {
+ input_report_abs(input_dev, ABS_MT_DISTANCE, -target->z);
+ input_report_abs(input_dev, ABS_DISTANCE, -target->z);
+ input_report_abs(input_dev, ABS_MT_PRESSURE, 0);
+ input_report_abs(input_dev, ABS_PRESSURE, 0);
+ }
+
+ if (!id)
+ input_report_key(input_dev, BTN_TOUCH, (current_state ==
+ AXIOM_TARGET_STATE_TOUCHING));
+ break;
+ default:
+ break;
+ }
+
+ target_prev_state->state = current_state;
+ target_prev_state->x = target->x;
+ target_prev_state->y = target->y;
+ target_prev_state->z = target->z;
+
+ return true;
+}
+
+/*
+ * U41 is the output report of the 2D CTS and contains the status of targets
+ * (including contacts and pre-contacts) along with their X,Y,Z values.
+ * When a target has been removed (no longer detected),
+ * the corresponding X,Y,Z values will be zeroed.
+ */
+static bool axiom_process_u41_report(struct axiom_data *ts, u8 *rx_buf)
+{
+ struct axiom_target_report target;
+ bool update_done = false;
+ u16 target_status;
+ int i;
+
+ target_status = get_unaligned_le16(rx_buf + 1);
+
+ for (i = 0; i < AXIOM_U41_MAX_TARGETS; i++) {
+ u8 *target_step = &rx_buf[i * 4];
+
+ target.index = i;
+ input_mt_slot(ts->input_dev, i);
+ input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
+ target.present = ((target_status & (1 << i)) != 0) ? 1 : 0;
+ target.x = get_unaligned_le16(target_step + 3);
+ target.y = get_unaligned_le16(target_step + 5);
+ target.z = (s8)(rx_buf[i + 43]);
+ touchscreen_report_pos(ts->input_dev, &ts->prop, target.x, target.y, true);
+ update_done |= axiom_process_u41_report_target(ts, &target);
+ }
+
+ return update_done;
+}
+
+/*
+ * U46 report contains a low level measurement data generated by the capacitive
+ * displacement sensor (CDS) algorithms from the auxiliary channels.
+ * This information is useful when tuning multi-press to assess mechanical
+ * consistency in the unit's construction.
+ */
+static void axiom_process_u46_report(struct axiom_data *ts, u8 *rx_buf)
+{
+ struct input_dev *input_dev = ts->input_dev;
+ u32 event_value;
+ u16 aux_value;
+ int i;
+
+ for (i = 0; i < AXIOM_U46_AUX_CHANNELS; i++) {
+ u8 *target_step = &rx_buf[i * 2];
+
+ input_mt_slot(input_dev, i);
+ input_mt_report_slot_state(input_dev, MT_TOOL_FINGER, true);
+ aux_value = get_unaligned_le16(target_step + 1) & AXIOM_U46_AUX_MASK;
+ event_value = (i << 16) | (aux_value);
+ input_event(input_dev, EV_MSC, MSC_RAW, event_value);
+ }
+}
+
+/*
+ * Validates the crc and demultiplexes the axiom reports to the appropriate
+ * report handler
+ */
+static int axiom_handle_events(struct axiom_data *ts)
+{
+ struct input_dev *input_dev = ts->input_dev;
+ u8 *report_data = ts->rx_buf;
+ struct device *dev = ts->dev;
+ u16 crc_report;
+ u8 *crc_bytes;
+ u16 crc_calc;
+ int error;
+ u8 len;
+
+ error = axiom_read(ts, AXIOM_REPORT_USAGE_ID, 0, report_data, ts->max_report_len);
+ if (error)
+ return error;
+
+ len = (report_data[0] & AXIOM_COMMS_REPORT_LEN_MASK) << 1;
+ if (len <= 2) {
+ dev_err(dev, "Zero length report discarded.\n");
+ return -ENODATA;
+ }
+
+ /* Validate the report CRC */
+ crc_bytes = &report_data[len];
+
+ crc_report = get_unaligned_le16(crc_bytes - 2);
+ /* Length is in 16 bit words and remove the size of the CRC16 itself */
+ crc_calc = crc16(0, report_data, (len - 2));
+
+ if (crc_calc != crc_report) {
+ dev_err(dev,
+ "CRC mismatch! Expected: %#x, Calculated CRC: %#x.\n",
+ crc_report, crc_calc);
+ return -EINVAL;
+ }
+
+ switch (report_data[1]) {
+ case AXIOM_USAGE_2DCTS_REPORT_ID:
+ if (axiom_process_u41_report(ts, &report_data[1])) {
+ input_mt_sync_frame(input_dev);
+ input_sync(input_dev);
+ }
+ break;
+
+ case AXIOM_USAGE_2AUX_REPORT_ID:
+ /* This is an aux report (force) */
+ axiom_process_u46_report(ts, &report_data[1]);
+ input_mt_sync(input_dev);
+ input_sync(input_dev);
+ break;
+
+ case AXIOM_USAGE_2HB_REPORT_ID:
+ /* This is a heartbeat report */
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void axiom_i2c_poll(struct input_dev *input_dev)
+{
+ struct axiom_data *ts = input_get_drvdata(input_dev);
+
+ axiom_handle_events(ts);
+}
+
+static irqreturn_t axiom_irq(int irq, void *dev_id)
+{
+ struct axiom_data *ts = dev_id;
+
+ axiom_handle_events(ts);
+
+ return IRQ_HANDLED;
+}
+
+static void axiom_reset(struct gpio_desc *reset_gpio)
+{
+ gpiod_set_value_cansleep(reset_gpio, 1);
+ usleep_range(1000, 2000);
+ gpiod_set_value_cansleep(reset_gpio, 0);
+ msleep(AXIOM_STARTUP_TIME_MS);
+}
+
+static int axiom_i2c_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct input_dev *input_dev;
+ struct axiom_data *ts;
+ u32 poll_interval;
+ int target;
+ int error;
+
+ ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, ts);
+ ts->client = client;
+ ts->dev = dev;
+
+ ts->regmap = devm_regmap_init_i2c(client, &axiom_i2c_regmap_config);
+ error = PTR_ERR_OR_ZERO(ts->regmap);
+ if (error) {
+ dev_err(dev, "Failed to initialize regmap: %d\n", error);
+ return error;
+ }
+
+ error = devm_regulator_get_enable(dev, "vddi");
+ if (error)
+ return dev_err_probe(&client->dev, error,
+ "Failed to enable VDDI regulator\n");
+
+ error = devm_regulator_get_enable(dev, "vdda");
+ if (error)
+ return dev_err_probe(&client->dev, error,
+ "Failed to enable VDDA regulator\n");
+
+ ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ts->reset_gpio))
+ return dev_err_probe(dev, PTR_ERR(ts->reset_gpio), "failed to get reset GPIO\n");
+
+ if (ts->reset_gpio)
+ axiom_reset(ts->reset_gpio);
+ else
+ msleep(AXIOM_STARTUP_TIME_MS);
+
+ error = axiom_discover(ts);
+ if (error)
+ return dev_err_probe(dev, error, "Failed touchscreen discover\n");
+
+ input_dev = devm_input_allocate_device(ts->dev);
+ if (!input_dev)
+ return -ENOMEM;
+
+ input_dev->name = "TouchNetix axiom Touchscreen";
+ input_dev->phys = "input/axiom_ts";
+
+ input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0, 65535, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0, 65535, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_TOOL_TYPE, 0, MT_TOOL_MAX, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_DISTANCE, 0, 127, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_PRESSURE, 0, 127, 0, 0);
+
+ touchscreen_parse_properties(input_dev, true, &ts->prop);
+
+ /* Registers the axiom device as a touchscreen instead of a mouse pointer */
+ error = input_mt_init_slots(input_dev, AXIOM_U41_MAX_TARGETS, INPUT_MT_DIRECT);
+ if (error)
+ return error;
+
+ /* Enables the raw data for up to 4 force channels to be sent to the input subsystem */
+ set_bit(EV_REL, input_dev->evbit);
+ set_bit(EV_MSC, input_dev->evbit);
+ /* Declare that we support "RAW" Miscellaneous events */
+ set_bit(MSC_RAW, input_dev->mscbit);
+
+ ts->input_dev = input_dev;
+ input_set_drvdata(ts->input_dev, ts);
+
+ /* Ensure that all reports are initialised to not be present. */
+ for (target = 0; target < AXIOM_U41_MAX_TARGETS; target++)
+ ts->targets[target].state = AXIOM_TARGET_STATE_NOT_PRESENT;
+
+ error = devm_request_threaded_irq(dev, client->irq, NULL,
+ axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
+ if (error) {
+ dev_info(dev, "Request irq failed, falling back to polling mode");
+
+ error = input_setup_polling(input_dev, axiom_i2c_poll);
+ if (error)
+ return dev_err_probe(ts->dev, error, "Unable to set up polling mode\n");
+
+ if (!device_property_read_u32(ts->dev, "poll-interval", &poll_interval))
+ input_set_poll_interval(input_dev, poll_interval);
+ else
+ input_set_poll_interval(input_dev, POLL_INTERVAL_DEFAULT_MS);
+ }
+
+ return input_register_device(input_dev);
+}
+
+static const struct i2c_device_id axiom_i2c_id_table[] = {
+ { "ax54a" },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, axiom_i2c_id_table);
+
+static const struct of_device_id axiom_i2c_of_match[] = {
+ { .compatible = "touchnetix,ax54a", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, axiom_i2c_of_match);
+
+static struct i2c_driver axiom_i2c_driver = {
+ .driver = {
+ .name = "axiom",
+ .of_match_table = axiom_i2c_of_match,
+ },
+ .id_table = axiom_i2c_id_table,
+ .probe = axiom_i2c_probe,
+};
+module_i2c_driver(axiom_i2c_driver);
+
+MODULE_AUTHOR("Bart Prescott <[email protected]>");
+MODULE_AUTHOR("Pedro Torruella <[email protected]>");
+MODULE_AUTHOR("Mark Satterthwaite <[email protected]>");
+MODULE_AUTHOR("Hannah Rossiter <[email protected]>");
+MODULE_AUTHOR("Kamel Bouhara <[email protected]>");
+MODULE_DESCRIPTION("TouchNetix axiom touchscreen I2C bus driver");
+MODULE_LICENSE("GPL");
--
2.25.1
Hi Kamel,
On Mon, Jun 03, 2024 at 05:39:25PM +0200, Kamel Bouhara wrote:
> Add a new driver for the TouchNetix's axiom family of
> touchscreen controllers. This driver only supports i2c
> and can be later adapted for SPI and USB support.
>
> Signed-off-by: Kamel Bouhara <[email protected]>
> ---
> MAINTAINERS | 2 +
> drivers/input/touchscreen/Kconfig | 14 +
> drivers/input/touchscreen/Makefile | 1 +
> drivers/input/touchscreen/touchnetix_axiom.c | 657 +++++++++++++++++++
> 4 files changed, 674 insertions(+)
> create mode 100644 drivers/input/touchscreen/touchnetix_axiom.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 225309db4110..a3ece12e32d7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -22744,9 +22744,11 @@ F: drivers/platform/x86/toshiba-wmi.c
>
> TOUCHNETIX AXIOM I2C TOUCHSCREEN DRIVER
> M: Kamel Bouhara <[email protected]>
> +M: [email protected]
> L: [email protected]
> S: Maintained
> F: Documentation/devicetree/bindings/input/touchscreen/touchnetix,ax54a.yaml
> +F: drivers/input/touchscreen/touchnetix_axiom.c
>
> TPM DEVICE DRIVER
> M: Peter Huewe <[email protected]>
> diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> index c821fe3ee794..1ce8f1c25625 100644
> --- a/drivers/input/touchscreen/Kconfig
> +++ b/drivers/input/touchscreen/Kconfig
> @@ -834,6 +834,20 @@ config TOUCHSCREEN_MIGOR
> To compile this driver as a module, choose M here: the
> module will be called migor_ts.
>
> +config TOUCHSCREEN_TOUCHNETIX_AXIOM
> + tristate "TouchNetix AXIOM based touchscreen controllers"
> + depends on I2C
> + select CRC16
> + select REGMAP_I2C
> + help
> + Say Y here if you have a axiom touchscreen connected to
> + your system.
> +
> + If unsure, say N.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called axiom.
> +
> config TOUCHSCREEN_TOUCHRIGHT
> tristate "Touchright serial touchscreen"
> select SERIO
> diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
> index a81cb5aa21a5..6ce7b804adc7 100644
> --- a/drivers/input/touchscreen/Makefile
> +++ b/drivers/input/touchscreen/Makefile
> @@ -91,6 +91,7 @@ obj-$(CONFIG_TOUCHSCREEN_SUR40) += sur40.o
> obj-$(CONFIG_TOUCHSCREEN_SURFACE3_SPI) += surface3_spi.o
> obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
> obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
> +obj-$(CONFIG_TOUCHSCREEN_TOUCHNETIX_AXIOM) += touchnetix_axiom.o
> obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
> obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
> obj-$(CONFIG_TOUCHSCREEN_TS4800) += ts4800-ts.o
> diff --git a/drivers/input/touchscreen/touchnetix_axiom.c b/drivers/input/touchscreen/touchnetix_axiom.c
> new file mode 100644
> index 000000000000..09550847392e
> --- /dev/null
> +++ b/drivers/input/touchscreen/touchnetix_axiom.c
> @@ -0,0 +1,657 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * TouchNetix axiom Touchscreen Driver
> + *
> + * Copyright (C) 2020-2023 TouchNetix Ltd.
> + *
> + * Author(s): Bart Prescott <[email protected]>
> + * Pedro Torruella <[email protected]>
> + * Mark Satterthwaite <[email protected]>
> + * Hannah Rossiter <[email protected]>
> + * Kamel Bouhara <[email protected]>
> + *
> + */
> +#include <linux/bitfield.h>
> +#include <linux/crc16.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/input.h>
> +#include <linux/input/mt.h>
> +#include <linux/input/touchscreen.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/regmap.h>
> +
> +#include <asm/unaligned.h>
> +#define AXIOM_PROX_LEVEL -128
> +#define AXIOM_DMA_OPS_DELAY_USEC 250
> +#define AXIOM_STARTUP_TIME_MS 110
> +/*
> + * Register group u31 has 2 pages for usage table entries.
> + */
> +#define AXIOM_U31_MAX_USAGES 0xff
> +#define AXIOM_U31_BYTES_PER_USAGE 6
> +#define AXIOM_U31_PAGE0_LENGTH 0x0C
> +#define AXIOM_U31_BOOTMODE_MASK BIT(7)
> +#define AXIOM_U31_DEVID_MASK GENMASK(14, 0)
> +
> +#define AXIOM_MAX_REPORT_LEN 0x7f
> +
> +#define AXIOM_CMD_HEADER_READ_MASK BIT(15)
> +#define AXIOM_U41_MAX_TARGETS 10
> +
> +#define AXIOM_U46_AUX_CHANNELS 4
> +#define AXIOM_U46_AUX_MASK GENMASK(11, 0)
> +
> +#define AXIOM_COMMS_MAX_USAGE_PAGES 3
> +#define AXIOM_COMMS_PAGE_SIZE 256
> +#define AXIOM_COMMS_REPORT_LEN_MASK GENMASK(6, 0)
> +
> +#define AXIOM_REPORT_USAGE_ID 0x34
> +#define AXIOM_DEVINFO_USAGE_ID 0x31
> +#define AXIOM_USAGE_2HB_REPORT_ID 0x01
> +#define AXIOM_USAGE_2AUX_REPORT_ID 0x46
> +#define AXIOM_USAGE_2DCTS_REPORT_ID 0x41
> +
> +#define AXIOM_PAGE_OFFSET_MASK GENMASK(6, 0)
> +
> +struct axiom_devinfo {
> + __le16 device_id;
> + u8 fw_minor;
> + u8 fw_major;
> + u8 fw_info_extra;
> + u8 tcp_revision;
> + u8 bootloader_fw_minor;
> + u8 bootloader_fw_major;
> + __le16 jedec_id;
> + u8 num_usages;
> +} __packed;
> +
> +/*
> + * Describes parameters of a specific usage, essentially a single element of
> + * the "Usage Table"
> + */
> +struct axiom_usage_entry {
> + u8 id;
> + u8 is_report;
This is probably a 'bool'.
> + u8 start_page;
> + u8 num_pages;
> +};
> +
> +/*
> + * Represents state of a touch or target when detected prior to a touch (eg.
> + * hover or proximity events).
> + */
> +enum axiom_target_state {
> + AXIOM_TARGET_STATE_NOT_PRESENT = 0,
> + AXIOM_TARGET_STATE_PROX = 1,
> + AXIOM_TARGET_STATE_HOVER = 2,
> + AXIOM_TARGET_STATE_TOUCHING = 3,
> +};
> +
> +struct axiom_u41_target {
> + enum axiom_target_state state;
> + u16 x;
> + u16 y;
> + s8 z;
> + bool insert;
What does "insert" mean here?
> + bool touch;
> +};
> +
> +struct axiom_target_report {
> + u8 index;
> + u8 present;
bool?
> + u16 x;
> + u16 y;
> + s8 z;
> +};
> +
> +struct axiom_cmd_header {
> + __le16 target_address;
> + __le16 length;
> +} __packed;
You do not need to declare this as packed, it is naturally aligned. You
can also make it a union with __le32 to ensure overall alignment.
> +
> +struct axiom_data {
> + struct axiom_devinfo devinfo;
> + struct device *dev;
> + struct gpio_desc *reset_gpio;
> + struct i2c_client *client;
> + struct input_dev *input_dev;
> + u32 max_report_len;
> + u8 rx_buf[AXIOM_COMMS_MAX_USAGE_PAGES * AXIOM_COMMS_PAGE_SIZE];
> + struct axiom_u41_target targets[AXIOM_U41_MAX_TARGETS];
> + struct axiom_usage_entry usage_table[AXIOM_U31_MAX_USAGES];
> + bool usage_table_populated;
> + struct regmap *regmap;
> + struct touchscreen_properties prop;
> +};
> +
> +static const struct regmap_config axiom_i2c_regmap_config = {
> + .reg_bits = 32,
> + .reg_format_endian = REGMAP_ENDIAN_LITTLE,
> + .val_bits = 8,
> + .val_format_endian = REGMAP_ENDIAN_LITTLE,
> +};
> +
> +/*
> + * axiom devices are typically configured to report touches at a rate
> + * of 100Hz (10ms) for systems that require polling for reports.
> + * When reports are polled, it will be expected to occasionally
> + * observe the overflow bit being set in the reports.
> + * This indicates that reports are not being read fast enough.
> + */
> +#define POLL_INTERVAL_DEFAULT_MS 10
> +
> +/* Translate usage/page/offset triplet into physical address. */
> +static u16 axiom_usage_to_target_address(struct axiom_data *ts, u8 usage, u8 page,
> + char offset)
> +{
> + /* At the moment the convention is that u31 is always at physical address 0x0 */
> + if (!ts->usage_table_populated) {
> + if (usage == AXIOM_DEVINFO_USAGE_ID)
> + return ((page << 8) + offset);
> + else
> + return 0xffff;
> + }
> +
> + if (page >= ts->usage_table[usage].num_pages) {
> + dev_err(ts->dev, "Invalid usage table! usage: u%02x, page: %02x, offset: %02x\n",
> + usage, page, offset);
> + return 0xffff;
> + }
> +
> + return ((ts->usage_table[usage].start_page + page) << 8) + offset;
> +}
> +
> +static int axiom_read(struct axiom_data *ts, u8 usage, u8 page, void *buf, u16 len)
> +{
> + struct axiom_cmd_header cmd_header;
> + u32 preamble;
> + int ret;
> +
> + cmd_header.target_address = cpu_to_le16(axiom_usage_to_target_address(ts, usage, page, 0));
> + cmd_header.length = cpu_to_le16(len | AXIOM_CMD_HEADER_READ_MASK);
> +
> + preamble = get_unaligned_le32(&cmd_header);
> +
> + ret = regmap_write(ts->regmap, preamble, 0);
> + if (ret) {
> + dev_err(ts->dev, "failed to write preamble, error %d\n", ret);
> + return ret;
> + }
> +
> + ret = regmap_raw_read(ts->regmap, 0, buf, len);
> + if (ret) {
> + dev_err(ts->dev, "failed to read target address %04x, error %d\n",
> + cmd_header.target_address, ret);
> + return ret;
> + }
> +
> + /* Wait device's DMA operations */
> + usleep_range(AXIOM_DMA_OPS_DELAY_USEC, AXIOM_DMA_OPS_DELAY_USEC + 50);
What exactly are we waiting for after getting the data?
> +
> + return 0;
> +}
> +
> +/*
> + * One of the main purposes for reading the usage table is to identify
> + * which usages reside at which target address.
> + * When performing subsequent reads or writes to AXIOM, the target address
> + * is used to specify which usage is being accessed.
> + * Consider the following discovery code which will build up the usage table.
> + */
> +static u32 axiom_populate_usage_table(struct axiom_data *ts)
> +{
> + struct axiom_usage_entry *usage_table;
> + u8 *rx_data = ts->rx_buf;
> + u32 max_report_len = 0;
> + u32 usage_id;
> + int error;
> +
> + usage_table = ts->usage_table;
> +
> + /* Read the second page of usage u31 to get the usage table */
> + error = axiom_read(ts, AXIOM_DEVINFO_USAGE_ID, 1, rx_data,
> + (AXIOM_U31_BYTES_PER_USAGE * ts->devinfo.num_usages));
> +
> + if (error)
> + return error;
> +
> + for (usage_id = 0; usage_id < ts->devinfo.num_usages; usage_id++) {
> + u16 offset = (usage_id * AXIOM_U31_BYTES_PER_USAGE);
> + u8 id = rx_data[offset + 0];
> + u8 start_page = rx_data[offset + 1];
> + u8 num_pages = rx_data[offset + 2];
> + u32 max_offset = ((rx_data[offset + 3] & AXIOM_PAGE_OFFSET_MASK) + 1) * 2;
> +
> + usage_table[id].is_report = !num_pages;
> +
> + /* Store the entry into the usage table */
> + usage_table[id].id = id;
> + usage_table[id].start_page = start_page;
> + usage_table[id].num_pages = num_pages;
> +
> + dev_dbg(ts->dev, "Usage u%02x Info: %*ph\n", id, AXIOM_U31_BYTES_PER_USAGE,
> + &rx_data[offset]);
> +
> + /* Identify the max report length the module will receive */
> + if (usage_table[id].is_report && max_offset > max_report_len)
> + max_report_len = max_offset;
> + }
> +
> + ts->usage_table_populated = true;
> +
> + return max_report_len;
> +}
> +
> +static int axiom_discover(struct axiom_data *ts)
> +{
> + int error;
> +
> + /*
> + * Fetch the first page of usage u31 to get the
> + * device information and the number of usages
> + */
> + error = axiom_read(ts, AXIOM_DEVINFO_USAGE_ID, 0, &ts->devinfo, AXIOM_U31_PAGE0_LENGTH);
> + if (error)
> + return error;
> +
> + dev_dbg(ts->dev, " Boot Mode : %s\n",
> + FIELD_GET(AXIOM_U31_BOOTMODE_MASK,
> + le16_to_cpu(ts->devinfo.device_id)) ? "BLP" : "TCP");
> + dev_dbg(ts->dev, " Device ID : %04lx\n",
> + FIELD_GET(AXIOM_U31_DEVID_MASK, le16_to_cpu(ts->devinfo.device_id)));
> + dev_dbg(ts->dev, " Firmware Rev : %02x.%02x\n", ts->devinfo.fw_major,
> + ts->devinfo.fw_minor);
> + dev_dbg(ts->dev, " Bootloader Rev : %02x.%02x\n", ts->devinfo.bootloader_fw_major,
> + ts->devinfo.bootloader_fw_minor);
> + dev_dbg(ts->dev, " FW Extra Info : %04x\n", ts->devinfo.fw_info_extra);
> + dev_dbg(ts->dev, " Silicon : %04x\n", le16_to_cpu(ts->devinfo.jedec_id));
> + dev_dbg(ts->dev, " Number usages : %04x\n", ts->devinfo.num_usages);
> +
> + ts->max_report_len = axiom_populate_usage_table(ts);
> + if (!ts->max_report_len || !ts->devinfo.num_usages ||
> + ts->max_report_len > AXIOM_MAX_REPORT_LEN) {
> + dev_err(ts->dev, "Invalid report length or usages number");
> + return -EINVAL;
> + }
> +
> + dev_dbg(ts->dev, "Max Report Length: %u\n", ts->max_report_len);
> +
> + return 0;
> +}
> +
> +/*
> + * Support function to axiom_process_u41_report.
> + * Generates input-subsystem events for every target.
> + * After calling this function the caller shall issue
> + * a Sync to the input sub-system.
> + */
> +static bool axiom_process_u41_report_target(struct axiom_data *ts,
> + struct axiom_target_report *target)
> +{
> + struct input_dev *input_dev = ts->input_dev;
> + struct axiom_u41_target *target_prev_state;
> + enum axiom_target_state current_state;
> + int id;
> +
> + /* Verify the target index */
> + if (target->index >= AXIOM_U41_MAX_TARGETS) {
> + dev_err(ts->dev, "Invalid target index! %u\n", target->index);
> + return false;
> + }
> +
> + target_prev_state = &ts->targets[target->index];
> +
> + current_state = AXIOM_TARGET_STATE_NOT_PRESENT;
> +
> + if (target->present) {
> + if (target->z >= 0)
> + current_state = AXIOM_TARGET_STATE_TOUCHING;
> + else if (target->z > AXIOM_PROX_LEVEL && target->z < 0)
> + current_state = AXIOM_TARGET_STATE_HOVER;
> + else if (target->z == AXIOM_PROX_LEVEL)
> + current_state = AXIOM_TARGET_STATE_PROX;
> + }
> +
> + if (target_prev_state->state == current_state &&
> + target_prev_state->x == target->x &&
> + target_prev_state->y == target->y &&
> + target_prev_state->z == target->z)
> + return false;
Why is this needed? Input/MT core already tries to suppress duplicate
events, I do not think we need to do it here.
> +
> + id = target->index;
> +
> + dev_dbg(ts->dev, "U41 Target T%u, present:%u, x:%u, y:%u, z:%d\n",
> + target->index, target->present,
> + target->x, target->y, target->z);
> +
> + switch (current_state) {
> + case AXIOM_TARGET_STATE_NOT_PRESENT:
> + case AXIOM_TARGET_STATE_PROX:
> + if (!target_prev_state->insert)
> + break;
> + target_prev_state->insert = false;
> +
> + if (!id)
> + input_report_key(input_dev, BTN_TOUCH, 0);
> +
> + input_mt_report_slot_inactive(input_dev);
> + /*
> + * make sure the previous coordinates are
> + * all off screen when the finger comes back
> + */
> + target->x = 65535;
> + target->y = 65535;
> + target->z = AXIOM_PROX_LEVEL;
> + break;
> + case AXIOM_TARGET_STATE_HOVER:
> + case AXIOM_TARGET_STATE_TOUCHING:
> + target_prev_state->insert = true;
> + input_report_abs(input_dev, ABS_MT_TRACKING_ID, id);
> + input_report_abs(input_dev, ABS_MT_POSITION_X, target->x);
> + input_report_abs(input_dev, ABS_MT_POSITION_Y, target->y);
> +
> + if (current_state == AXIOM_TARGET_STATE_TOUCHING) {
> + input_report_abs(input_dev, ABS_MT_DISTANCE, 0);
> + input_report_abs(input_dev, ABS_DISTANCE, 0);
> + input_report_abs(input_dev, ABS_MT_PRESSURE, target->z);
> + input_report_abs(input_dev, ABS_PRESSURE, target->z);
You only need to emit ABS_MT_DISTANCE and ABS_MT_PRESSURE. The
single-touch variants should be generated by the input core as part of
sending out the frame.
> + } else {
> + input_report_abs(input_dev, ABS_MT_DISTANCE, -target->z);
> + input_report_abs(input_dev, ABS_DISTANCE, -target->z);
> + input_report_abs(input_dev, ABS_MT_PRESSURE, 0);
> + input_report_abs(input_dev, ABS_PRESSURE, 0);
> + }
> +
> + if (!id)
> + input_report_key(input_dev, BTN_TOUCH, (current_state ==
> + AXIOM_TARGET_STATE_TOUCHING));
Why do you emit BTN_TOUCH manually instead of replying on
input_mt_sync_frame() calling input_mt_pointer_emulation().
> + break;
> + default:
> + break;
> + }
> +
> + target_prev_state->state = current_state;
> + target_prev_state->x = target->x;
> + target_prev_state->y = target->y;
> + target_prev_state->z = target->z;
> +
> + return true;
> +}
> +
> +/*
> + * U41 is the output report of the 2D CTS and contains the status of targets
> + * (including contacts and pre-contacts) along with their X,Y,Z values.
> + * When a target has been removed (no longer detected),
> + * the corresponding X,Y,Z values will be zeroed.
> + */
> +static bool axiom_process_u41_report(struct axiom_data *ts, u8 *rx_buf)
> +{
> + struct axiom_target_report target;
> + bool update_done = false;
> + u16 target_status;
> + int i;
> +
> + target_status = get_unaligned_le16(rx_buf + 1);
> +
> + for (i = 0; i < AXIOM_U41_MAX_TARGETS; i++) {
> + u8 *target_step = &rx_buf[i * 4];
> +
> + target.index = i;
> + input_mt_slot(ts->input_dev, i);
> + input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
> + target.present = ((target_status & (1 << i)) != 0) ? 1 : 0;
> + target.x = get_unaligned_le16(target_step + 3);
> + target.y = get_unaligned_le16(target_step + 5);
> + target.z = (s8)(rx_buf[i + 43]);
> + touchscreen_report_pos(ts->input_dev, &ts->prop, target.x, target.y, true);
I find it confusing that you send out coordinates here, and the rest of
events in axiom_process_u41_report_target()... Can it all be done in one
place?
> + update_done |= axiom_process_u41_report_target(ts, &target);
> + }
> +
> + return update_done;
> +}
> +
> +/*
> + * U46 report contains a low level measurement data generated by the capacitive
> + * displacement sensor (CDS) algorithms from the auxiliary channels.
> + * This information is useful when tuning multi-press to assess mechanical
> + * consistency in the unit's construction.
> + */
> +static void axiom_process_u46_report(struct axiom_data *ts, u8 *rx_buf)
> +{
> + struct input_dev *input_dev = ts->input_dev;
> + u32 event_value;
> + u16 aux_value;
> + int i;
> +
> + for (i = 0; i < AXIOM_U46_AUX_CHANNELS; i++) {
> + u8 *target_step = &rx_buf[i * 2];
> +
> + input_mt_slot(input_dev, i);
> + input_mt_report_slot_state(input_dev, MT_TOOL_FINGER, true);
> + aux_value = get_unaligned_le16(target_step + 1) & AXIOM_U46_AUX_MASK;
> + event_value = (i << 16) | (aux_value);
> + input_event(input_dev, EV_MSC, MSC_RAW, event_value);
This does not really belong to the input subsystem. I recommend using
debugfs to provide this data. Some drivers also use v4l to provide a
"picture" of the heat map.
> + }
> +}
> +
> +/*
> + * Validates the crc and demultiplexes the axiom reports to the appropriate
> + * report handler
> + */
> +static int axiom_handle_events(struct axiom_data *ts)
> +{
> + struct input_dev *input_dev = ts->input_dev;
> + u8 *report_data = ts->rx_buf;
> + struct device *dev = ts->dev;
> + u16 crc_report;
> + u8 *crc_bytes;
> + u16 crc_calc;
> + int error;
> + u8 len;
> +
> + error = axiom_read(ts, AXIOM_REPORT_USAGE_ID, 0, report_data, ts->max_report_len);
> + if (error)
> + return error;
> +
> + len = (report_data[0] & AXIOM_COMMS_REPORT_LEN_MASK) << 1;
> + if (len <= 2) {
> + dev_err(dev, "Zero length report discarded.\n");
> + return -ENODATA;
> + }
> +
> + /* Validate the report CRC */
> + crc_bytes = &report_data[len];
> +
> + crc_report = get_unaligned_le16(crc_bytes - 2);
> + /* Length is in 16 bit words and remove the size of the CRC16 itself */
> + crc_calc = crc16(0, report_data, (len - 2));
> +
> + if (crc_calc != crc_report) {
> + dev_err(dev,
> + "CRC mismatch! Expected: %#x, Calculated CRC: %#x.\n",
> + crc_report, crc_calc);
> + return -EINVAL;
> + }
> +
> + switch (report_data[1]) {
> + case AXIOM_USAGE_2DCTS_REPORT_ID:
> + if (axiom_process_u41_report(ts, &report_data[1])) {
> + input_mt_sync_frame(input_dev);
> + input_sync(input_dev);
> + }
> + break;
> +
> + case AXIOM_USAGE_2AUX_REPORT_ID:
> + /* This is an aux report (force) */
> + axiom_process_u46_report(ts, &report_data[1]);
> + input_mt_sync(input_dev);
> + input_sync(input_dev);
> + break;
> +
> + case AXIOM_USAGE_2HB_REPORT_ID:
> + /* This is a heartbeat report */
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static void axiom_i2c_poll(struct input_dev *input_dev)
> +{
> + struct axiom_data *ts = input_get_drvdata(input_dev);
> +
> + axiom_handle_events(ts);
> +}
> +
> +static irqreturn_t axiom_irq(int irq, void *dev_id)
> +{
> + struct axiom_data *ts = dev_id;
> +
> + axiom_handle_events(ts);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static void axiom_reset(struct gpio_desc *reset_gpio)
> +{
> + gpiod_set_value_cansleep(reset_gpio, 1);
> + usleep_range(1000, 2000);
> + gpiod_set_value_cansleep(reset_gpio, 0);
> + msleep(AXIOM_STARTUP_TIME_MS);
> +}
> +
> +static int axiom_i2c_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct input_dev *input_dev;
> + struct axiom_data *ts;
> + u32 poll_interval;
> + int target;
> + int error;
> +
> + ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
> + if (!ts)
> + return -ENOMEM;
> +
> + i2c_set_clientdata(client, ts);
> + ts->client = client;
> + ts->dev = dev;
> +
> + ts->regmap = devm_regmap_init_i2c(client, &axiom_i2c_regmap_config);
> + error = PTR_ERR_OR_ZERO(ts->regmap);
> + if (error) {
> + dev_err(dev, "Failed to initialize regmap: %d\n", error);
> + return error;
> + }
> +
> + error = devm_regulator_get_enable(dev, "vddi");
> + if (error)
> + return dev_err_probe(&client->dev, error,
> + "Failed to enable VDDI regulator\n");
> +
> + error = devm_regulator_get_enable(dev, "vdda");
> + if (error)
> + return dev_err_probe(&client->dev, error,
> + "Failed to enable VDDA regulator\n");
> +
> + ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(ts->reset_gpio))
> + return dev_err_probe(dev, PTR_ERR(ts->reset_gpio), "failed to get reset GPIO\n");
> +
> + if (ts->reset_gpio)
> + axiom_reset(ts->reset_gpio);
> + else
> + msleep(AXIOM_STARTUP_TIME_MS);
Should this be called unconditionally (and matching msleep() be removed
from axiom_i2c_probe)?
> +
> + error = axiom_discover(ts);
> + if (error)
> + return dev_err_probe(dev, error, "Failed touchscreen discover\n");
> +
> + input_dev = devm_input_allocate_device(ts->dev);
> + if (!input_dev)
> + return -ENOMEM;
> +
> + input_dev->name = "TouchNetix axiom Touchscreen";
> + input_dev->phys = "input/axiom_ts";
> +
> + input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0, 65535, 0, 0);
> + input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0, 65535, 0, 0);
> + input_set_abs_params(input_dev, ABS_MT_TOOL_TYPE, 0, MT_TOOL_MAX, 0, 0);
The only tool you report is finger, who do you declare more?
> + input_set_abs_params(input_dev, ABS_MT_DISTANCE, 0, 127, 0, 0);
> + input_set_abs_params(input_dev, ABS_MT_PRESSURE, 0, 127, 0, 0);
> +
> + touchscreen_parse_properties(input_dev, true, &ts->prop);
> +
> + /* Registers the axiom device as a touchscreen instead of a mouse pointer */
> + error = input_mt_init_slots(input_dev, AXIOM_U41_MAX_TARGETS, INPUT_MT_DIRECT);
> + if (error)
> + return error;
> +
> + /* Enables the raw data for up to 4 force channels to be sent to the input subsystem */
> + set_bit(EV_REL, input_dev->evbit);
The driver does not emit any relative events...
> + set_bit(EV_MSC, input_dev->evbit);
> + /* Declare that we support "RAW" Miscellaneous events */
> + set_bit(MSC_RAW, input_dev->mscbit);
> +
> + ts->input_dev = input_dev;
> + input_set_drvdata(ts->input_dev, ts);
> +
> + /* Ensure that all reports are initialised to not be present. */
> + for (target = 0; target < AXIOM_U41_MAX_TARGETS; target++)
> + ts->targets[target].state = AXIOM_TARGET_STATE_NOT_PRESENT;
> +
> + error = devm_request_threaded_irq(dev, client->irq, NULL,
> + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
> + if (error) {
> + dev_info(dev, "Request irq failed, falling back to polling mode");
I do not think you should fall back to polling mode if you fail to get
interrupt. If it was not specified (client->irq) then I can see that we
might want to fall back, but if the system configured for using
interrupt and you can not get it you should bail out.
> +
> + error = input_setup_polling(input_dev, axiom_i2c_poll);
> + if (error)
> + return dev_err_probe(ts->dev, error, "Unable to set up polling mode\n");
> +
> + if (!device_property_read_u32(ts->dev, "poll-interval", &poll_interval))
> + input_set_poll_interval(input_dev, poll_interval);
> + else
> + input_set_poll_interval(input_dev, POLL_INTERVAL_DEFAULT_MS);
> + }
> +
> + return input_register_device(input_dev);
Please use
error = input_register_device(..);
if (error)
return dev_err_probe(...);
return 0;
Thanks.
--
Dmitry
Le Mon, Jun 03, 2024 at 05:02:33PM -0700, Dmitry Torokhov a ?crit :
> Hi Kamel,
>
Hi Dmitry,
> On Mon, Jun 03, 2024 at 05:39:25PM +0200, Kamel Bouhara wrote:
> > Add a new driver for the TouchNetix's axiom family of
> > touchscreen controllers. This driver only supports i2c
> > and can be later adapted for SPI and USB support.
> >
> > Signed-off-by: Kamel Bouhara <[email protected]>
> > ---
> > MAINTAINERS | 2 +
> > drivers/input/touchscreen/Kconfig | 14 +
> > drivers/input/touchscreen/Makefile | 1 +
> > drivers/input/touchscreen/touchnetix_axiom.c | 657 +++++++++++++++++++
> > 4 files changed, 674 insertions(+)
> > create mode 100644 drivers/input/touchscreen/touchnetix_axiom.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 225309db4110..a3ece12e32d7 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -22744,9 +22744,11 @@ F: drivers/platform/x86/toshiba-wmi.c
> >
> > TOUCHNETIX AXIOM I2C TOUCHSCREEN DRIVER
> > M: Kamel Bouhara <[email protected]>
> > +M: [email protected]
> > L: [email protected]
> > S: Maintained
> > F: Documentation/devicetree/bindings/input/touchscreen/touchnetix,ax54a.yaml
> > +F: drivers/input/touchscreen/touchnetix_axiom.c
> >
> > TPM DEVICE DRIVER
> > M: Peter Huewe <[email protected]>
> > diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> > index c821fe3ee794..1ce8f1c25625 100644
> > --- a/drivers/input/touchscreen/Kconfig
> > +++ b/drivers/input/touchscreen/Kconfig
> > @@ -834,6 +834,20 @@ config TOUCHSCREEN_MIGOR
> > To compile this driver as a module, choose M here: the
> > module will be called migor_ts.
> >
> > +config TOUCHSCREEN_TOUCHNETIX_AXIOM
> > + tristate "TouchNetix AXIOM based touchscreen controllers"
> > + depends on I2C
> > + select CRC16
> > + select REGMAP_I2C
> > + help
> > + Say Y here if you have a axiom touchscreen connected to
> > + your system.
> > +
> > + If unsure, say N.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called axiom.
> > +
> > config TOUCHSCREEN_TOUCHRIGHT
> > tristate "Touchright serial touchscreen"
> > select SERIO
> > diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
> > index a81cb5aa21a5..6ce7b804adc7 100644
> > --- a/drivers/input/touchscreen/Makefile
> > +++ b/drivers/input/touchscreen/Makefile
> > @@ -91,6 +91,7 @@ obj-$(CONFIG_TOUCHSCREEN_SUR40) += sur40.o
> > obj-$(CONFIG_TOUCHSCREEN_SURFACE3_SPI) += surface3_spi.o
> > obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
> > obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
> > +obj-$(CONFIG_TOUCHSCREEN_TOUCHNETIX_AXIOM) += touchnetix_axiom.o
> > obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
> > obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
> > obj-$(CONFIG_TOUCHSCREEN_TS4800) += ts4800-ts.o
> > diff --git a/drivers/input/touchscreen/touchnetix_axiom.c b/drivers/input/touchscreen/touchnetix_axiom.c
> > new file mode 100644
> > index 000000000000..09550847392e
> > --- /dev/null
> > +++ b/drivers/input/touchscreen/touchnetix_axiom.c
> > @@ -0,0 +1,657 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * TouchNetix axiom Touchscreen Driver
> > + *
> > + * Copyright (C) 2020-2023 TouchNetix Ltd.
> > + *
> > + * Author(s): Bart Prescott <[email protected]>
> > + * Pedro Torruella <[email protected]>
> > + * Mark Satterthwaite <[email protected]>
> > + * Hannah Rossiter <[email protected]>
> > + * Kamel Bouhara <[email protected]>
> > + *
> > + */
> > +#include <linux/bitfield.h>
> > +#include <linux/crc16.h>
> > +#include <linux/delay.h>
> > +#include <linux/device.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/i2c.h>
> > +#include <linux/input.h>
> > +#include <linux/input/mt.h>
> > +#include <linux/input/touchscreen.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/regmap.h>
> > +
> > +#include <asm/unaligned.h>
> > +#define AXIOM_PROX_LEVEL -128
> > +#define AXIOM_DMA_OPS_DELAY_USEC 250
> > +#define AXIOM_STARTUP_TIME_MS 110
> > +/*
> > + * Register group u31 has 2 pages for usage table entries.
> > + */
> > +#define AXIOM_U31_MAX_USAGES 0xff
> > +#define AXIOM_U31_BYTES_PER_USAGE 6
> > +#define AXIOM_U31_PAGE0_LENGTH 0x0C
> > +#define AXIOM_U31_BOOTMODE_MASK BIT(7)
> > +#define AXIOM_U31_DEVID_MASK GENMASK(14, 0)
> > +
> > +#define AXIOM_MAX_REPORT_LEN 0x7f
> > +
> > +#define AXIOM_CMD_HEADER_READ_MASK BIT(15)
> > +#define AXIOM_U41_MAX_TARGETS 10
> > +
> > +#define AXIOM_U46_AUX_CHANNELS 4
> > +#define AXIOM_U46_AUX_MASK GENMASK(11, 0)
> > +
> > +#define AXIOM_COMMS_MAX_USAGE_PAGES 3
> > +#define AXIOM_COMMS_PAGE_SIZE 256
> > +#define AXIOM_COMMS_REPORT_LEN_MASK GENMASK(6, 0)
> > +
> > +#define AXIOM_REPORT_USAGE_ID 0x34
> > +#define AXIOM_DEVINFO_USAGE_ID 0x31
> > +#define AXIOM_USAGE_2HB_REPORT_ID 0x01
> > +#define AXIOM_USAGE_2AUX_REPORT_ID 0x46
> > +#define AXIOM_USAGE_2DCTS_REPORT_ID 0x41
> > +
> > +#define AXIOM_PAGE_OFFSET_MASK GENMASK(6, 0)
> > +
> > +struct axiom_devinfo {
> > + __le16 device_id;
> > + u8 fw_minor;
> > + u8 fw_major;
> > + u8 fw_info_extra;
> > + u8 tcp_revision;
> > + u8 bootloader_fw_minor;
> > + u8 bootloader_fw_major;
> > + __le16 jedec_id;
> > + u8 num_usages;
> > +} __packed;
> > +
> > +/*
> > + * Describes parameters of a specific usage, essentially a single element of
> > + * the "Usage Table"
> > + */
> > +struct axiom_usage_entry {
> > + u8 id;
> > + u8 is_report;
>
> This is probably a 'bool'.
Fixed thanks.
>
> > + u8 start_page;
> > + u8 num_pages;
> > +};
> > +
> > +/*
> > + * Represents state of a touch or target when detected prior to a touch (eg.
> > + * hover or proximity events).
> > + */
> > +enum axiom_target_state {
> > + AXIOM_TARGET_STATE_NOT_PRESENT = 0,
> > + AXIOM_TARGET_STATE_PROX = 1,
> > + AXIOM_TARGET_STATE_HOVER = 2,
> > + AXIOM_TARGET_STATE_TOUCHING = 3,
> > +};
> > +
> > +struct axiom_u41_target {
> > + enum axiom_target_state state;
> > + u16 x;
> > + u16 y;
> > + s8 z;
> > + bool insert;
>
> What does "insert" mean here?
I think this means target data are reported.
>
> > + bool touch;
> > +};
> > +
> > +struct axiom_target_report {
> > + u8 index;
> > + u8 present;
>
> bool?
>
> > + u16 x;
> > + u16 y;
> > + s8 z;
> > +};
> > +
> > +struct axiom_cmd_header {
> > + __le16 target_address;
> > + __le16 length;
> > +} __packed;
>
> You do not need to declare this as packed, it is naturally aligned. You
> can also make it a union with __le32 to ensure overall alignment.
Ack, fixed for v14.
>
> > +
> > +struct axiom_data {
> > + struct axiom_devinfo devinfo;
> > + struct device *dev;
> > + struct gpio_desc *reset_gpio;
> > + struct i2c_client *client;
> > + struct input_dev *input_dev;
> > + u32 max_report_len;
> > + u8 rx_buf[AXIOM_COMMS_MAX_USAGE_PAGES * AXIOM_COMMS_PAGE_SIZE];
> > + struct axiom_u41_target targets[AXIOM_U41_MAX_TARGETS];
> > + struct axiom_usage_entry usage_table[AXIOM_U31_MAX_USAGES];
> > + bool usage_table_populated;
> > + struct regmap *regmap;
> > + struct touchscreen_properties prop;
> > +};
> > +
> > +static const struct regmap_config axiom_i2c_regmap_config = {
> > + .reg_bits = 32,
> > + .reg_format_endian = REGMAP_ENDIAN_LITTLE,
> > + .val_bits = 8,
> > + .val_format_endian = REGMAP_ENDIAN_LITTLE,
> > +};
> > +
> > +/*
> > + * axiom devices are typically configured to report touches at a rate
> > + * of 100Hz (10ms) for systems that require polling for reports.
> > + * When reports are polled, it will be expected to occasionally
> > + * observe the overflow bit being set in the reports.
> > + * This indicates that reports are not being read fast enough.
> > + */
> > +#define POLL_INTERVAL_DEFAULT_MS 10
> > +
> > +/* Translate usage/page/offset triplet into physical address. */
> > +static u16 axiom_usage_to_target_address(struct axiom_data *ts, u8 usage, u8 page,
> > + char offset)
> > +{
> > + /* At the moment the convention is that u31 is always at physical address 0x0 */
> > + if (!ts->usage_table_populated) {
> > + if (usage == AXIOM_DEVINFO_USAGE_ID)
> > + return ((page << 8) + offset);
> > + else
> > + return 0xffff;
> > + }
> > +
> > + if (page >= ts->usage_table[usage].num_pages) {
> > + dev_err(ts->dev, "Invalid usage table! usage: u%02x, page: %02x, offset: %02x\n",
> > + usage, page, offset);
> > + return 0xffff;
> > + }
> > +
> > + return ((ts->usage_table[usage].start_page + page) << 8) + offset;
> > +}
> > +
> > +static int axiom_read(struct axiom_data *ts, u8 usage, u8 page, void *buf, u16 len)
> > +{
> > + struct axiom_cmd_header cmd_header;
> > + u32 preamble;
> > + int ret;
> > +
> > + cmd_header.target_address = cpu_to_le16(axiom_usage_to_target_address(ts, usage, page, 0));
> > + cmd_header.length = cpu_to_le16(len | AXIOM_CMD_HEADER_READ_MASK);
> > +
> > + preamble = get_unaligned_le32(&cmd_header);
> > +
> > + ret = regmap_write(ts->regmap, preamble, 0);
> > + if (ret) {
> > + dev_err(ts->dev, "failed to write preamble, error %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = regmap_raw_read(ts->regmap, 0, buf, len);
> > + if (ret) {
> > + dev_err(ts->dev, "failed to read target address %04x, error %d\n",
> > + cmd_header.target_address, ret);
> > + return ret;
> > + }
> > +
> > + /* Wait device's DMA operations */
> > + usleep_range(AXIOM_DMA_OPS_DELAY_USEC, AXIOM_DMA_OPS_DELAY_USEC + 50);
>
> What exactly are we waiting for after getting the data?
That is the minimum delay required the device need to flush it's
internal dma buffers.
>
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * One of the main purposes for reading the usage table is to identify
> > + * which usages reside at which target address.
> > + * When performing subsequent reads or writes to AXIOM, the target address
> > + * is used to specify which usage is being accessed.
> > + * Consider the following discovery code which will build up the usage table.
> > + */
> > +static u32 axiom_populate_usage_table(struct axiom_data *ts)
> > +{
> > + struct axiom_usage_entry *usage_table;
> > + u8 *rx_data = ts->rx_buf;
> > + u32 max_report_len = 0;
> > + u32 usage_id;
> > + int error;
> > +
> > + usage_table = ts->usage_table;
> > +
> > + /* Read the second page of usage u31 to get the usage table */
> > + error = axiom_read(ts, AXIOM_DEVINFO_USAGE_ID, 1, rx_data,
> > + (AXIOM_U31_BYTES_PER_USAGE * ts->devinfo.num_usages));
> > +
> > + if (error)
> > + return error;
> > +
> > + for (usage_id = 0; usage_id < ts->devinfo.num_usages; usage_id++) {
> > + u16 offset = (usage_id * AXIOM_U31_BYTES_PER_USAGE);
> > + u8 id = rx_data[offset + 0];
> > + u8 start_page = rx_data[offset + 1];
> > + u8 num_pages = rx_data[offset + 2];
> > + u32 max_offset = ((rx_data[offset + 3] & AXIOM_PAGE_OFFSET_MASK) + 1) * 2;
> > +
> > + usage_table[id].is_report = !num_pages;
> > +
> > + /* Store the entry into the usage table */
> > + usage_table[id].id = id;
> > + usage_table[id].start_page = start_page;
> > + usage_table[id].num_pages = num_pages;
> > +
> > + dev_dbg(ts->dev, "Usage u%02x Info: %*ph\n", id, AXIOM_U31_BYTES_PER_USAGE,
> > + &rx_data[offset]);
> > +
> > + /* Identify the max report length the module will receive */
> > + if (usage_table[id].is_report && max_offset > max_report_len)
> > + max_report_len = max_offset;
> > + }
> > +
> > + ts->usage_table_populated = true;
> > +
> > + return max_report_len;
> > +}
> > +
> > +static int axiom_discover(struct axiom_data *ts)
> > +{
> > + int error;
> > +
> > + /*
> > + * Fetch the first page of usage u31 to get the
> > + * device information and the number of usages
> > + */
> > + error = axiom_read(ts, AXIOM_DEVINFO_USAGE_ID, 0, &ts->devinfo, AXIOM_U31_PAGE0_LENGTH);
> > + if (error)
> > + return error;
> > +
> > + dev_dbg(ts->dev, " Boot Mode : %s\n",
> > + FIELD_GET(AXIOM_U31_BOOTMODE_MASK,
> > + le16_to_cpu(ts->devinfo.device_id)) ? "BLP" : "TCP");
> > + dev_dbg(ts->dev, " Device ID : %04lx\n",
> > + FIELD_GET(AXIOM_U31_DEVID_MASK, le16_to_cpu(ts->devinfo.device_id)));
> > + dev_dbg(ts->dev, " Firmware Rev : %02x.%02x\n", ts->devinfo.fw_major,
> > + ts->devinfo.fw_minor);
> > + dev_dbg(ts->dev, " Bootloader Rev : %02x.%02x\n", ts->devinfo.bootloader_fw_major,
> > + ts->devinfo.bootloader_fw_minor);
> > + dev_dbg(ts->dev, " FW Extra Info : %04x\n", ts->devinfo.fw_info_extra);
> > + dev_dbg(ts->dev, " Silicon : %04x\n", le16_to_cpu(ts->devinfo.jedec_id));
> > + dev_dbg(ts->dev, " Number usages : %04x\n", ts->devinfo.num_usages);
> > +
> > + ts->max_report_len = axiom_populate_usage_table(ts);
> > + if (!ts->max_report_len || !ts->devinfo.num_usages ||
> > + ts->max_report_len > AXIOM_MAX_REPORT_LEN) {
> > + dev_err(ts->dev, "Invalid report length or usages number");
> > + return -EINVAL;
> > + }
> > +
> > + dev_dbg(ts->dev, "Max Report Length: %u\n", ts->max_report_len);
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * Support function to axiom_process_u41_report.
> > + * Generates input-subsystem events for every target.
> > + * After calling this function the caller shall issue
> > + * a Sync to the input sub-system.
> > + */
> > +static bool axiom_process_u41_report_target(struct axiom_data *ts,
> > + struct axiom_target_report *target)
> > +{
> > + struct input_dev *input_dev = ts->input_dev;
> > + struct axiom_u41_target *target_prev_state;
> > + enum axiom_target_state current_state;
> > + int id;
> > +
> > + /* Verify the target index */
> > + if (target->index >= AXIOM_U41_MAX_TARGETS) {
> > + dev_err(ts->dev, "Invalid target index! %u\n", target->index);
> > + return false;
> > + }
> > +
> > + target_prev_state = &ts->targets[target->index];
> > +
> > + current_state = AXIOM_TARGET_STATE_NOT_PRESENT;
> > +
> > + if (target->present) {
> > + if (target->z >= 0)
> > + current_state = AXIOM_TARGET_STATE_TOUCHING;
> > + else if (target->z > AXIOM_PROX_LEVEL && target->z < 0)
> > + current_state = AXIOM_TARGET_STATE_HOVER;
> > + else if (target->z == AXIOM_PROX_LEVEL)
> > + current_state = AXIOM_TARGET_STATE_PROX;
> > + }
> > +
> > + if (target_prev_state->state == current_state &&
> > + target_prev_state->x == target->x &&
> > + target_prev_state->y == target->y &&
> > + target_prev_state->z == target->z)
> > + return false;
>
> Why is this needed? Input/MT core already tries to suppress duplicate
> events, I do not think we need to do it here.
>
This indeed make sure we don't have twice the same report processed.
> > +
> > + id = target->index;
> > +
> > + dev_dbg(ts->dev, "U41 Target T%u, present:%u, x:%u, y:%u, z:%d\n",
> > + target->index, target->present,
> > + target->x, target->y, target->z);
> > +
> > + switch (current_state) {
> > + case AXIOM_TARGET_STATE_NOT_PRESENT:
> > + case AXIOM_TARGET_STATE_PROX:
> > + if (!target_prev_state->insert)
> > + break;
> > + target_prev_state->insert = false;
> > +
> > + if (!id)
> > + input_report_key(input_dev, BTN_TOUCH, 0);
> > +
> > + input_mt_report_slot_inactive(input_dev);
> > + /*
> > + * make sure the previous coordinates are
> > + * all off screen when the finger comes back
> > + */
> > + target->x = 65535;
> > + target->y = 65535;
> > + target->z = AXIOM_PROX_LEVEL;
> > + break;
> > + case AXIOM_TARGET_STATE_HOVER:
> > + case AXIOM_TARGET_STATE_TOUCHING:
> > + target_prev_state->insert = true;
> > + input_report_abs(input_dev, ABS_MT_TRACKING_ID, id);
> > + input_report_abs(input_dev, ABS_MT_POSITION_X, target->x);
> > + input_report_abs(input_dev, ABS_MT_POSITION_Y, target->y);
> > +
> > + if (current_state == AXIOM_TARGET_STATE_TOUCHING) {
> > + input_report_abs(input_dev, ABS_MT_DISTANCE, 0);
> > + input_report_abs(input_dev, ABS_DISTANCE, 0);
> > + input_report_abs(input_dev, ABS_MT_PRESSURE, target->z);
> > + input_report_abs(input_dev, ABS_PRESSURE, target->z);
>
> You only need to emit ABS_MT_DISTANCE and ABS_MT_PRESSURE. The
> single-touch variants should be generated by the input core as part of
> sending out the frame.
>
Ack, thanks.
> > + } else {
> > + input_report_abs(input_dev, ABS_MT_DISTANCE, -target->z);
> > + input_report_abs(input_dev, ABS_DISTANCE, -target->z);
> > + input_report_abs(input_dev, ABS_MT_PRESSURE, 0);
> > + input_report_abs(input_dev, ABS_PRESSURE, 0);
> > + }
> > +
> > + if (!id)
> > + input_report_key(input_dev, BTN_TOUCH, (current_state ==
> > + AXIOM_TARGET_STATE_TOUCHING));
>
> Why do you emit BTN_TOUCH manually instead of replying on
> input_mt_sync_frame() calling input_mt_pointer_emulation().
Sorry this really requires a comment line as it is to indicate when the
target is the first reported contact and Im actually not sure this
should be kept as it.
>
> > + break;
> > + default:
> > + break;
> > + }
> > +
> > + target_prev_state->state = current_state;
> > + target_prev_state->x = target->x;
> > + target_prev_state->y = target->y;
> > + target_prev_state->z = target->z;
> > +
> > + return true;
> > +}
> > +
> > +/*
> > + * U41 is the output report of the 2D CTS and contains the status of targets
> > + * (including contacts and pre-contacts) along with their X,Y,Z values.
> > + * When a target has been removed (no longer detected),
> > + * the corresponding X,Y,Z values will be zeroed.
> > + */
> > +static bool axiom_process_u41_report(struct axiom_data *ts, u8 *rx_buf)
> > +{
> > + struct axiom_target_report target;
> > + bool update_done = false;
> > + u16 target_status;
> > + int i;
> > +
> > + target_status = get_unaligned_le16(rx_buf + 1);
> > +
> > + for (i = 0; i < AXIOM_U41_MAX_TARGETS; i++) {
> > + u8 *target_step = &rx_buf[i * 4];
> > +
> > + target.index = i;
> > + input_mt_slot(ts->input_dev, i);
> > + input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
> > + target.present = ((target_status & (1 << i)) != 0) ? 1 : 0;
> > + target.x = get_unaligned_le16(target_step + 3);
> > + target.y = get_unaligned_le16(target_step + 5);
> > + target.z = (s8)(rx_buf[i + 43]);
> > + touchscreen_report_pos(ts->input_dev, &ts->prop, target.x, target.y, true);
>
> I find it confusing that you send out coordinates here, and the rest of
> events in axiom_process_u41_report_target()... Can it all be done in one
> place?
Sure this will be moved in axiom_process_u41_report_target() for v14.
>
> > + update_done |= axiom_process_u41_report_target(ts, &target);
> > + }
> > +
> > + return update_done;
> > +}
> > +
> > +/*
> > + * U46 report contains a low level measurement data generated by the capacitive
> > + * displacement sensor (CDS) algorithms from the auxiliary channels.
> > + * This information is useful when tuning multi-press to assess mechanical
> > + * consistency in the unit's construction.
> > + */
> > +static void axiom_process_u46_report(struct axiom_data *ts, u8 *rx_buf)
> > +{
> > + struct input_dev *input_dev = ts->input_dev;
> > + u32 event_value;
> > + u16 aux_value;
> > + int i;
> > +
> > + for (i = 0; i < AXIOM_U46_AUX_CHANNELS; i++) {
> > + u8 *target_step = &rx_buf[i * 2];
> > +
> > + input_mt_slot(input_dev, i);
> > + input_mt_report_slot_state(input_dev, MT_TOOL_FINGER, true);
> > + aux_value = get_unaligned_le16(target_step + 1) & AXIOM_U46_AUX_MASK;
> > + event_value = (i << 16) | (aux_value);
> > + input_event(input_dev, EV_MSC, MSC_RAW, event_value);
>
> This does not really belong to the input subsystem. I recommend using
> debugfs to provide this data. Some drivers also use v4l to provide a
> "picture" of the heat map.
Ack, I will just remove it here, this is used when force sensing data
(u46) are available.
>
> > + }
> > +}
> > +
> > +/*
> > + * Validates the crc and demultiplexes the axiom reports to the appropriate
> > + * report handler
> > + */
> > +static int axiom_handle_events(struct axiom_data *ts)
> > +{
> > + struct input_dev *input_dev = ts->input_dev;
> > + u8 *report_data = ts->rx_buf;
> > + struct device *dev = ts->dev;
> > + u16 crc_report;
> > + u8 *crc_bytes;
> > + u16 crc_calc;
> > + int error;
> > + u8 len;
> > +
> > + error = axiom_read(ts, AXIOM_REPORT_USAGE_ID, 0, report_data, ts->max_report_len);
> > + if (error)
> > + return error;
> > +
> > + len = (report_data[0] & AXIOM_COMMS_REPORT_LEN_MASK) << 1;
> > + if (len <= 2) {
> > + dev_err(dev, "Zero length report discarded.\n");
> > + return -ENODATA;
> > + }
> > +
> > + /* Validate the report CRC */
> > + crc_bytes = &report_data[len];
> > +
> > + crc_report = get_unaligned_le16(crc_bytes - 2);
> > + /* Length is in 16 bit words and remove the size of the CRC16 itself */
> > + crc_calc = crc16(0, report_data, (len - 2));
> > +
> > + if (crc_calc != crc_report) {
> > + dev_err(dev,
> > + "CRC mismatch! Expected: %#x, Calculated CRC: %#x.\n",
> > + crc_report, crc_calc);
> > + return -EINVAL;
> > + }
> > +
> > + switch (report_data[1]) {
> > + case AXIOM_USAGE_2DCTS_REPORT_ID:
> > + if (axiom_process_u41_report(ts, &report_data[1])) {
> > + input_mt_sync_frame(input_dev);
> > + input_sync(input_dev);
> > + }
> > + break;
> > +
> > + case AXIOM_USAGE_2AUX_REPORT_ID:
> > + /* This is an aux report (force) */
> > + axiom_process_u46_report(ts, &report_data[1]);
> > + input_mt_sync(input_dev);
> > + input_sync(input_dev);
> > + break;
> > +
> > + case AXIOM_USAGE_2HB_REPORT_ID:
> > + /* This is a heartbeat report */
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void axiom_i2c_poll(struct input_dev *input_dev)
> > +{
> > + struct axiom_data *ts = input_get_drvdata(input_dev);
> > +
> > + axiom_handle_events(ts);
> > +}
> > +
> > +static irqreturn_t axiom_irq(int irq, void *dev_id)
> > +{
> > + struct axiom_data *ts = dev_id;
> > +
> > + axiom_handle_events(ts);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static void axiom_reset(struct gpio_desc *reset_gpio)
> > +{
> > + gpiod_set_value_cansleep(reset_gpio, 1);
> > + usleep_range(1000, 2000);
> > + gpiod_set_value_cansleep(reset_gpio, 0);
> > + msleep(AXIOM_STARTUP_TIME_MS);
> > +}
> > +
> > +static int axiom_i2c_probe(struct i2c_client *client)
> > +{
> > + struct device *dev = &client->dev;
> > + struct input_dev *input_dev;
> > + struct axiom_data *ts;
> > + u32 poll_interval;
> > + int target;
> > + int error;
> > +
> > + ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
> > + if (!ts)
> > + return -ENOMEM;
> > +
> > + i2c_set_clientdata(client, ts);
> > + ts->client = client;
> > + ts->dev = dev;
> > +
> > + ts->regmap = devm_regmap_init_i2c(client, &axiom_i2c_regmap_config);
> > + error = PTR_ERR_OR_ZERO(ts->regmap);
> > + if (error) {
> > + dev_err(dev, "Failed to initialize regmap: %d\n", error);
> > + return error;
> > + }
> > +
> > + error = devm_regulator_get_enable(dev, "vddi");
> > + if (error)
> > + return dev_err_probe(&client->dev, error,
> > + "Failed to enable VDDI regulator\n");
> > +
> > + error = devm_regulator_get_enable(dev, "vdda");
> > + if (error)
> > + return dev_err_probe(&client->dev, error,
> > + "Failed to enable VDDA regulator\n");
> > +
> > + ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> > + if (IS_ERR(ts->reset_gpio))
> > + return dev_err_probe(dev, PTR_ERR(ts->reset_gpio), "failed to get reset GPIO\n");
> > +
> > + if (ts->reset_gpio)
> > + axiom_reset(ts->reset_gpio);
> > + else
> > + msleep(AXIOM_STARTUP_TIME_MS);
>
> Should this be called unconditionally (and matching msleep() be removed
> from axiom_i2c_probe)?
>
The reset gpio being optional we need to make sure the time after a
power ON sequence is meet. I could still move the power sequence in a
axiom_power_on() if this make things clearer.
> > +
> > + error = axiom_discover(ts);
> > + if (error)
> > + return dev_err_probe(dev, error, "Failed touchscreen discover\n");
> > +
> > + input_dev = devm_input_allocate_device(ts->dev);
> > + if (!input_dev)
> > + return -ENOMEM;
> > +
> > + input_dev->name = "TouchNetix axiom Touchscreen";
> > + input_dev->phys = "input/axiom_ts";
> > +
> > + input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0, 65535, 0, 0);
> > + input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0, 65535, 0, 0);
> > + input_set_abs_params(input_dev, ABS_MT_TOOL_TYPE, 0, MT_TOOL_MAX, 0, 0);
>
> The only tool you report is finger, who do you declare more?
This is a mistake only finger is required.
>
> > + input_set_abs_params(input_dev, ABS_MT_DISTANCE, 0, 127, 0, 0);
> > + input_set_abs_params(input_dev, ABS_MT_PRESSURE, 0, 127, 0, 0);
> > +
> > + touchscreen_parse_properties(input_dev, true, &ts->prop);
> > +
> > + /* Registers the axiom device as a touchscreen instead of a mouse pointer */
> > + error = input_mt_init_slots(input_dev, AXIOM_U41_MAX_TARGETS, INPUT_MT_DIRECT);
> > + if (error)
> > + return error;
> > +
> > + /* Enables the raw data for up to 4 force channels to be sent to the input subsystem */
> > + set_bit(EV_REL, input_dev->evbit);
>
> The driver does not emit any relative events...
Fixed, thanks.
>
> > + set_bit(EV_MSC, input_dev->evbit);
> > + /* Declare that we support "RAW" Miscellaneous events */
> > + set_bit(MSC_RAW, input_dev->mscbit);
> > +
> > + ts->input_dev = input_dev;
> > + input_set_drvdata(ts->input_dev, ts);
> > +
> > + /* Ensure that all reports are initialised to not be present. */
> > + for (target = 0; target < AXIOM_U41_MAX_TARGETS; target++)
> > + ts->targets[target].state = AXIOM_TARGET_STATE_NOT_PRESENT;
> > +
> > + error = devm_request_threaded_irq(dev, client->irq, NULL,
> > + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
> > + if (error) {
> > + dev_info(dev, "Request irq failed, falling back to polling mode");
>
> I do not think you should fall back to polling mode if you fail to get
> interrupt. If it was not specified (client->irq) then I can see that we
> might want to fall back, but if the system configured for using
> interrupt and you can not get it you should bail out.
>
Yes, clear, the polling mode can be decorrelated to the irq not provided
case.
> > +
> > + error = input_setup_polling(input_dev, axiom_i2c_poll);
> > + if (error)
> > + return dev_err_probe(ts->dev, error, "Unable to set up polling mode\n");
> > +
> > + if (!device_property_read_u32(ts->dev, "poll-interval", &poll_interval))
> > + input_set_poll_interval(input_dev, poll_interval);
> > + else
> > + input_set_poll_interval(input_dev, POLL_INTERVAL_DEFAULT_MS);
> > + }
> > +
> > + return input_register_device(input_dev);
>
> Please use
>
> error = input_register_device(..);
> if (error)
> return dev_err_probe(...);
>
> return 0;
>
Fixed, thanks.
> Thanks.
>
> --
> Dmitry
--
Kamel Bouhara, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
[...]
>> > +
>> > + error = devm_request_threaded_irq(dev, client->irq, NULL,
>> > + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
>> > + if (error) {
>> > + dev_info(dev, "Request irq failed, falling back to polling mode");
>>
>> I do not think you should fall back to polling mode if you fail to get
>> interrupt. If it was not specified (client->irq) then I can see that
>> we
>> might want to fall back, but if the system configured for using
>> interrupt and you can not get it you should bail out.
>>
>
> Yes, clear, the polling mode can be decorrelated to the irq not
> provided
> case.
Just to make sure I understood, is this what you propose ?
if (client->irq) {
error = devm_request_threaded_irq(...)
if (error) {
dev_warn(dev, "failed to request IRQ\n");
client->irq = 0;
}
}
if(!client->irq) {
// setup polling stuff
...
}
--
Kamel Bouhara, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
On Wed, Jun 05, 2024 at 03:48:20PM +0200, Kamel BOUHARA wrote:
> [...]
>
> > > > +
> > > > + error = devm_request_threaded_irq(dev, client->irq, NULL,
> > > > + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
> > > > + if (error) {
> > > > + dev_info(dev, "Request irq failed, falling back to polling mode");
> > >
> > > I do not think you should fall back to polling mode if you fail to get
> > > interrupt. If it was not specified (client->irq) then I can see that
> > > we
> > > might want to fall back, but if the system configured for using
> > > interrupt and you can not get it you should bail out.
> > >
> >
> > Yes, clear, the polling mode can be decorrelated to the irq not provided
> > case.
>
> Just to make sure I understood, is this what you propose ?
>
> if (client->irq) {
> error = devm_request_threaded_irq(...)
> if (error) {
> dev_warn(dev, "failed to request IRQ\n");
> client->irq = 0;
> }
> }
>
> if(!client->irq)?{
> // setup polling stuff
> ...
> }
No, if you fail to acquire interrupt that was described in ACPI/DT it
should be treated as an error, like this:
if (client->irq) {
error = devm_request_threaded_irq(...)
if (error)
return dev_err_probe(...);
} else {
.. set up polling ..
}
This also makes sure that if interrupt controller is not ready and
requests probe deferral we will not end up with device in polling mode.
Thanks.
--
Dmitry
Hello Dmitry,
> On Wed, Jun 05, 2024 at 03:48:20PM +0200, Kamel BOUHARA wrote:
>> [...]
>>
>> > > > +
>> > > > + error = devm_request_threaded_irq(dev, client->irq, NULL,
>> > > > + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
>> > > > + if (error) {
>> > > > + dev_info(dev, "Request irq failed, falling back to polling mode");
>> > >
>> > > I do not think you should fall back to polling mode if you fail to get
>> > > interrupt. If it was not specified (client->irq) then I can see that
>> > > we
>> > > might want to fall back, but if the system configured for using
>> > > interrupt and you can not get it you should bail out.
>> > >
>> >
>> > Yes, clear, the polling mode can be decorrelated to the irq not provided
>> > case.
>>
>> Just to make sure I understood, is this what you propose ?
>>
>> if (client->irq) {
>> error = devm_request_threaded_irq(...)
>> if (error) {
>> dev_warn(dev, "failed to request IRQ\n");
>> client->irq = 0;
>> }
>> }
>>
>> if(!client->irq) {
>> // setup polling stuff
>> ...
>> }
>
> No, if you fail to acquire interrupt that was described in ACPI/DT it
> should be treated as an error, like this:
>
> if (client->irq) {
> error = devm_request_threaded_irq(...)
> if (error)
> return dev_err_probe(...);
> } else {
> .. set up polling ..
> }
>
> This also makes sure that if interrupt controller is not ready and
> requests probe deferral we will not end up with device in polling
> mode.
In the case of probe deferral, I see the benefit of treating it as an
error. However, in the other case, I find it better to fall back to
polling mode with a big error message than just exiting in error. As a
user, I think we prefer having a degraded feature over not having the
feature at all.
So what about something like:
if (client->irq) {
error = devm_request_threaded_irq(...)
if (error == -EPROBE_DEFER)
return dev_err_probe(...);
dev_warn("Big error message");
client->irq = 0;
}
if (!client->irq) {
.. set up polling ..
}
Gregory
>
> Thanks.
>
> --
> Dmitry
Hi Gregory,
On Fri, Jun 07, 2024 at 09:23:36AM +0200, Gregory CLEMENT wrote:
> Hello Dmitry,
>
> > On Wed, Jun 05, 2024 at 03:48:20PM +0200, Kamel BOUHARA wrote:
> >> [...]
> >>
> >> > > > +
> >> > > > + error = devm_request_threaded_irq(dev, client->irq, NULL,
> >> > > > + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
> >> > > > + if (error) {
> >> > > > + dev_info(dev, "Request irq failed, falling back to polling mode");
> >> > >
> >> > > I do not think you should fall back to polling mode if you fail to get
> >> > > interrupt. If it was not specified (client->irq) then I can see that
> >> > > we
> >> > > might want to fall back, but if the system configured for using
> >> > > interrupt and you can not get it you should bail out.
> >> > >
> >> >
> >> > Yes, clear, the polling mode can be decorrelated to the irq not provided
> >> > case.
> >>
> >> Just to make sure I understood, is this what you propose ?
> >>
> >> if (client->irq) {
> >> error = devm_request_threaded_irq(...)
> >> if (error) {
> >> dev_warn(dev, "failed to request IRQ\n");
> >> client->irq = 0;
> >> }
> >> }
> >>
> >> if(!client->irq)?{
> >> // setup polling stuff
> >> ...
> >> }
> >
> > No, if you fail to acquire interrupt that was described in ACPI/DT it
> > should be treated as an error, like this:
> >
> > if (client->irq) {
> > error = devm_request_threaded_irq(...)
> > if (error)
> > return dev_err_probe(...);
> > } else {
> > .. set up polling ..
> > }
> >
> > This also makes sure that if interrupt controller is not ready and
> > requests probe deferral we will not end up with device in polling
> > mode.
>
> In the case of probe deferral, I see the benefit of treating it as an
> error. However, in the other case, I find it better to fall back to
> polling mode with a big error message than just exiting in error. As a
> user, I think we prefer having a degraded feature over not having the
> feature at all.
No, this is not how the drivers work, we do not simply ignore errors and
hope for the best. If resources are described in platform definition (be
it ACPI or device tree) they need to be there and they need to work. It
is true for regulators and reset gpios (you do not ignore errors if you
fail to obtain a them in the hope that the device is operable), and you
should not ignore errors when trying to set up interrupt.
Thanks.
--
Dmitry
Le 2024-06-06 23:32, Dmitry Torokhov a écrit :
> On Wed, Jun 05, 2024 at 03:48:20PM +0200, Kamel BOUHARA wrote:
>> [...]
>>
>> > > > +
>> > > > + error = devm_request_threaded_irq(dev, client->irq, NULL,
>> > > > + axiom_irq, IRQF_ONESHOT, dev_name(dev), ts);
>> > > > + if (error) {
>> > > > + dev_info(dev, "Request irq failed, falling back to polling mode");
>> > >
>> > > I do not think you should fall back to polling mode if you fail to get
>> > > interrupt. If it was not specified (client->irq) then I can see that
>> > > we
>> > > might want to fall back, but if the system configured for using
>> > > interrupt and you can not get it you should bail out.
>> > >
>> >
>> > Yes, clear, the polling mode can be decorrelated to the irq not provided
>> > case.
>>
>> Just to make sure I understood, is this what you propose ?
>>
>> if (client->irq) {
>> error = devm_request_threaded_irq(...)
>> if (error) {
>> dev_warn(dev, "failed to request IRQ\n");
>> client->irq = 0;
>> }
>> }
>>
>> if(!client->irq) {
>> // setup polling stuff
>> ...
>> }
>
> No, if you fail to acquire interrupt that was described in ACPI/DT it
> should be treated as an error, like this:
>
> if (client->irq) {
> error = devm_request_threaded_irq(...)
> if (error)
> return dev_err_probe(...);
> } else {
> .. set up polling ..
> }
>
> This also makes sure that if interrupt controller is not ready and
> requests probe deferral we will not end up with device in polling mode.
>
OK, thanks for the clarification, this is fixed in v14.
Greetings,
--
Kamel Bouhara, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com