2017-06-12 07:46:18

by Li Wei

[permalink] [raw]
Subject: [PATCH v3] mmc: dw_mmc-k3: add sd support for hi3660

Add sd card support for hi3660 soc

Major changes in v3:
- solve review comments from Heiner Kallweit.
*use the GENMASK and FIELD_PREP macros replace the bit shift operation.
*use usleep_range() replace udelay() and mdelay().

Signed-off-by: Li Wei <[email protected]>
Signed-off-by: Chen Jun <[email protected]>
---
drivers/mmc/host/dw_mmc-k3.c | 314 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 314 insertions(+)

diff --git a/drivers/mmc/host/dw_mmc-k3.c b/drivers/mmc/host/dw_mmc-k3.c
index e38fb0020bb1..a6e13bd83b9f 100644
--- a/drivers/mmc/host/dw_mmc-k3.c
+++ b/drivers/mmc/host/dw_mmc-k3.c
@@ -8,6 +8,8 @@
* (at your option) any later version.
*/

+#include <linux/bitops.h>
+#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/mfd/syscon.h>
#include <linux/mmc/host.h>
@@ -28,7 +30,40 @@
#define AO_SCTRL_SEL18 BIT(10)
#define AO_SCTRL_CTRL3 0x40C

+#define DWMMC_SD_ID 1
+#define DWMMC_SDIO_ID 2
+
+#define SOC_SCTRL_SCPERCTRL5 (0x314)
+#define SDCARD_IO_SEL18 BIT(2)
+
+#define GENCLK_DIV (7)
+
+#define GPIO_CLK_ENABLE BIT(16)
+#define GPIO_CLK_DIV_MASK GENMASK(11, 8)
+#define GPIO_USE_SAMPLE_DLY_MASK GENMASK(13, 13)
+#define UHS_REG_EXT_SAMPLE_PHASE_MASK GENMASK(20, 16)
+#define UHS_REG_EXT_SAMPLE_DRVPHASE_MASK GENMASK(25, 21)
+#define UHS_REG_EXT_SAMPLE_DLY_MASK GENMASK(30, 26)
+
+#define SDMMC_UHS_REG_EXT 0x108
+#define SDMMC_ENABLE_SHIFT 0x110
+
+#define TIMING_MODE 3
+#define TIMING_CFG_NUM 10
+
+#define PULL_DOWN BIT(1)
+#define PULL_UP BIT(0)
+
+#define NUM_PHASES (40)
+
+#define ENABLE_SHIFT_MIN_SMPL (4)
+#define ENABLE_SHIFT_MAX_SMPL (12)
+#define USE_DLY_MIN_SMPL (11)
+#define USE_DLY_MAX_SMPL (14)
+
struct k3_priv {
+ u8 ctrl_id;
+ u32 cur_speed;
struct regmap *reg;
};

@@ -38,6 +73,41 @@ static unsigned long dw_mci_hi6220_caps[] = {
0
};

+struct hs_timing {
+ int drv_phase;
+ int sam_dly;
+ int sam_phase_max;
+ int sam_phase_min;
+};
+
+struct hs_timing hs_timing_cfg[TIMING_MODE][TIMING_CFG_NUM] = {
+ { /* reserved */ },
+ { /* SD */
+ {7, 0, 15, 15,}, /* 0: LEGACY 400k */
+ {6, 0, 4, 4,}, /* 1: MMC_HS */
+ {6, 0, 3, 3,}, /* 2: SD_HS */
+ {6, 0, 15, 15,}, /* 3: SDR12 */
+ {6, 0, 2, 2,}, /* 4: SDR25 */
+ {4, 0, 11, 0,}, /* 5: SDR50 */
+ {6, 4, 15, 0,}, /* 6: SDR104 */
+ {0}, /* 7: DDR50 */
+ {0}, /* 8: DDR52 */
+ {0}, /* 9: HS200 */
+ },
+ { /* SDIO */
+ {7, 0, 15, 15,}, /* 0: LEGACY 400k */
+ {0}, /* 1: MMC_HS */
+ {6, 0, 15, 15,}, /* 2: SD_HS */
+ {6, 0, 15, 15,}, /* 3: SDR12 */
+ {6, 0, 0, 0,}, /* 4: SDR25 */
+ {4, 0, 12, 0,}, /* 5: SDR50 */
+ {5, 4, 15, 0,}, /* 6: SDR104 */
+ {0}, /* 7: DDR50 */
+ {0}, /* 8: DDR52 */
+ {0}, /* 9: HS200 */
+ }
+};
+
static void dw_mci_k3_set_ios(struct dw_mci *host, struct mmc_ios *ios)
{
int ret;
@@ -66,6 +136,10 @@ static int dw_mci_hi6220_parse_dt(struct dw_mci *host)
if (IS_ERR(priv->reg))
priv->reg = NULL;

+ priv->ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
+ if (priv->ctrl_id < 0)
+ priv->ctrl_id = 0;
+
host->priv = priv;
return 0;
}
@@ -144,7 +218,242 @@ static const struct dw_mci_drv_data hi6220_data = {
.execute_tuning = dw_mci_hi6220_execute_tuning,
};

+static void dw_mci_hs_set_timing(struct dw_mci *host, int timing, int sam_phase)
+{
+ int drv_phase;
+ int sam_dly;
+ int ctrl_id;
+ int use_sam_dly = 0;
+ int enable_shift = 0;
+ int reg_value;
+ struct k3_priv *priv;
+
+ priv = host->priv;
+ ctrl_id = priv->ctrl_id;
+
+ drv_phase = hs_timing_cfg[ctrl_id][timing].drv_phase;
+ sam_dly = hs_timing_cfg[ctrl_id][timing].sam_dly;
+ if (sam_phase == -1)
+ sam_phase = (hs_timing_cfg[ctrl_id][timing].sam_phase_max +
+ hs_timing_cfg[ctrl_id][timing].sam_phase_min) / 2;
+
+ if (timing == MMC_TIMING_UHS_SDR50 ||
+ timing == MMC_TIMING_UHS_SDR104) {
+ if (sam_phase >= ENABLE_SHIFT_MIN_SMPL &&
+ sam_phase <= ENABLE_SHIFT_MAX_SMPL)
+ enable_shift = 1;
+ }
+ if (timing == MMC_TIMING_UHS_SDR104) {
+ if (sam_phase >= USE_DLY_MIN_SMPL &&
+ sam_phase <= USE_DLY_MAX_SMPL)
+ use_sam_dly = 1;
+ }
+
+ mci_writel(host, GPIO, 0x0);
+ usleep_range(5, 10);
+
+ reg_value = FIELD_PREP(UHS_REG_EXT_SAMPLE_PHASE_MASK, sam_phase) |\
+ FIELD_PREP(UHS_REG_EXT_SAMPLE_DLY_MASK ,sam_dly) |\
+ FIELD_PREP(UHS_REG_EXT_SAMPLE_DRVPHASE_MASK,drv_phase);
+ mci_writel(host, UHS_REG_EXT, reg_value);
+
+ mci_writel(host, ENABLE_SHIFT, enable_shift);
+
+ reg_value = FIELD_PREP(GPIO_CLK_DIV_MASK, GENCLK_DIV) |\
+ FIELD_PREP(GPIO_USE_SAMPLE_DLY_MASK,use_sam_dly);
+ mci_writel(host, GPIO, (unsigned int)reg_value | GPIO_CLK_ENABLE);
+
+ /* We should delay 1ms wait for timing setting finished. */
+ usleep_range(1000, 2000);
+}
+
+int dw_mci_hi3660_init(struct dw_mci *host)
+{
+ /* set threshold to 512 bytes */
+ mci_writel(host, CDTHRCTL, 0x02000001);
+
+ dw_mci_hs_set_timing(host, MMC_TIMING_LEGACY, -1);
+ host->bus_hz /= (GENCLK_DIV + 1);
+
+ return 0;
+}
+
+static int dw_mci_set_sel18(struct dw_mci *host, bool set)
+{
+ int ret;
+ unsigned int val;
+ struct k3_priv *priv;
+
+ priv = host->priv;
+
+ val = set ? SDCARD_IO_SEL18 : 0;
+ ret = regmap_update_bits(priv->reg, SOC_SCTRL_SCPERCTRL5,
+ SDCARD_IO_SEL18, val);
+ if (ret) {
+ dev_err(host->dev, "sel18 %u error\n", val);
+ return ret;
+ }
+
+ return 0;
+}
+
+void dw_mci_hi3660_set_ios(struct dw_mci *host, struct mmc_ios *ios)
+{
+ int ret;
+ unsigned long wanted;
+ unsigned long actual;
+ struct k3_priv *priv = host->priv;
+
+ if (!ios->clock || ios->clock == priv->cur_speed)
+ return;
+
+ wanted = ios->clock * (GENCLK_DIV + 1);
+ ret = clk_set_rate(host->ciu_clk, wanted);
+ if (ret) {
+ dev_err(host->dev, "failed to set rate %luHz\n", wanted);
+ return;
+ }
+ actual = clk_get_rate(host->ciu_clk);
+
+ dw_mci_hs_set_timing(host, ios->timing, -1);
+ host->bus_hz = actual / (GENCLK_DIV + 1);
+ host->current_speed = 0;
+ priv->cur_speed = host->bus_hz;
+}
+
+static int dw_mci_get_best_clksmpl(unsigned int sample_flag)
+{
+ int i;
+ int interval;
+ unsigned int v;
+ unsigned int len;
+ unsigned int range_start = 0;
+ unsigned int range_length = 0;
+ unsigned int middle_range = 0;
+
+ if (!sample_flag)
+ return -EIO;
+
+ if (~sample_flag == 0)
+ return 0;
+
+ i = ffs(sample_flag) - 1;
+
+ /*A clock cycle is divided into 32 phases,
+ *each of which is represented by a bit, finding the optimal phase.
+ */
+ while (i < 32) {
+ v = ror32(sample_flag, i);
+ len = ffs(~v) - 1;
+
+ if (len > range_length) {
+ range_length = len;
+ range_start = i;
+ }
+
+ interval = ffs(v >> len) - 1;
+ if (interval < 0)
+ break;
+
+ i += len + interval;
+ }
+
+ middle_range = range_start + range_length / 2;
+ if (middle_range >= 32)
+ middle_range %= 32;
+
+ return middle_range;
+}
+
+static int dw_mci_hi3660_execute_tuning(struct dw_mci_slot *slot, u32 opcode)
+{
+ int i = 0;
+ struct dw_mci *host = slot->host;
+ struct mmc_host *mmc = slot->mmc;
+ int sam_phase = 0;
+ u32 tuning_sample_flag = 0;
+ int best_clksmpl = 0;
+
+ for (i = 0; i < NUM_PHASES; ++i, ++sam_phase) {
+ sam_phase %= 32;
+
+ mci_writel(host, TMOUT, ~0);
+ dw_mci_hs_set_timing(host, mmc->ios.timing, sam_phase);
+
+ if (!mmc_send_tuning(mmc, opcode, NULL))
+ tuning_sample_flag |= (1 << sam_phase);
+ else
+ tuning_sample_flag &= ~(1 << sam_phase);
+ }
+
+ best_clksmpl = dw_mci_get_best_clksmpl(tuning_sample_flag);
+ if (best_clksmpl < 0) {
+ dev_err(host->dev, "All phases bad!\n");
+ return -EIO;
+ }
+
+ dw_mci_hs_set_timing(host, mmc->ios.timing, best_clksmpl);
+
+ dev_info(host->dev, "tuning ok best_clksmpl %u tuning_sample_flag %x\n",
+ best_clksmpl, tuning_sample_flag);
+ return 0;
+}
+
+static int dw_mci_hi3660_switch_voltage(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ int ret;
+ int min_uv = 0;
+ int max_uv = 0;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct k3_priv *priv;
+ struct dw_mci *host;
+
+ host = slot->host;
+ priv = host->priv;
+
+ if (!priv || !priv->reg)
+ return 0;
+
+ if (priv->ctrl_id == DWMMC_SDIO_ID)
+ return 0;
+
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
+ ret = dw_mci_set_sel18(host, 0);
+ if (ret)
+ return ret;
+ min_uv = 2950000;
+ max_uv = 2950000;
+ } else if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
+ ret = dw_mci_set_sel18(host, 1);
+ if (ret)
+ return ret;
+ min_uv = 1800000;
+ max_uv = 1800000;
+ }
+
+ if (IS_ERR_OR_NULL(mmc->supply.vqmmc))
+ return 0;
+
+ ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv);
+ if (ret) {
+ dev_dbg(host->dev, "Regulator set error %d: %d - %d\n",
+ ret, min_uv, max_uv);
+ return ret;
+ }
+ return 0;
+}
+
+static const struct dw_mci_drv_data hi3660_data = {
+ .init = dw_mci_hi3660_init,
+ .set_ios = dw_mci_hi3660_set_ios,
+ .parse_dt = dw_mci_hi6220_parse_dt,
+ .execute_tuning = dw_mci_hi3660_execute_tuning,
+ .switch_voltage = dw_mci_hi3660_switch_voltage,
+};
+
static const struct of_device_id dw_mci_k3_match[] = {
+ { .compatible = "hisilicon,hi3660-dw-mshc", .data = &hi3660_data, },
{ .compatible = "hisilicon,hi4511-dw-mshc", .data = &k3_drv_data, },
{ .compatible = "hisilicon,hi6220-dw-mshc", .data = &hi6220_data, },
{},
@@ -155,6 +464,11 @@ static int dw_mci_k3_probe(struct platform_device *pdev)
{
const struct dw_mci_drv_data *drv_data;
const struct of_device_id *match;
+ struct reset_control *rst;
+
+ rst = devm_reset_control_get(&pdev->dev, NULL);
+ if (!IS_ERR(rst))
+ reset_control_reset(rst);

match = of_match_node(dw_mci_k3_match, pdev->dev.of_node);
drv_data = match->data;
--
2.11.0


2017-06-12 22:23:46

by Jaehoon Chung

[permalink] [raw]
Subject: Re: [PATCH v3] mmc: dw_mmc-k3: add sd support for hi3660

Hi,

On 06/12/2017 11:27 PM, Jaehoon Chung wrote:
> Hi Li,
>
> On 2017년 06월 12일 16:46, liwei wrote:
>> Add sd card support for hi3660 soc
>>
>> Major changes in v3:
>> - solve review comments from Heiner Kallweit.
>> *use the GENMASK and FIELD_PREP macros replace the bit shift operation.
>> *use usleep_range() replace udelay() and mdelay().
>
> I had added the some comments about your previous patch.
> Refer to below...
>
> https://patchwork.kernel.org/patch/9747495/

Before sending patch, run checkpatch...I will not apply this patch.

Best Regards,
Jaehoon Chung

>
>>
>> Signed-off-by: Li Wei <[email protected]>
>> Signed-off-by: Chen Jun <[email protected]>
>> ---
>
> Locate changelog at here.
>
> Best Regards,
> Jaehoon Chung
>
>> drivers/mmc/host/dw_mmc-k3.c | 314 +++++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 314 insertions(+)
>>
>> diff --git a/drivers/mmc/host/dw_mmc-k3.c b/drivers/mmc/host/dw_mmc-k3.c
>> index e38fb0020bb1..a6e13bd83b9f 100644
>> --- a/drivers/mmc/host/dw_mmc-k3.c
>> +++ b/drivers/mmc/host/dw_mmc-k3.c
>> @@ -8,6 +8,8 @@
>> * (at your option) any later version.
>> */
>>
>> +#include <linux/bitops.h>
>> +#include <linux/bitfield.h>
>> #include <linux/clk.h>
>> #include <linux/mfd/syscon.h>
>> #include <linux/mmc/host.h>
>> @@ -28,7 +30,40 @@
>> #define AO_SCTRL_SEL18 BIT(10)
>> #define AO_SCTRL_CTRL3 0x40C
>>
>> +#define DWMMC_SD_ID 1
>> +#define DWMMC_SDIO_ID 2
>> +
>> +#define SOC_SCTRL_SCPERCTRL5 (0x314)
>> +#define SDCARD_IO_SEL18 BIT(2)
>> +
>> +#define GENCLK_DIV (7)
>> +
>> +#define GPIO_CLK_ENABLE BIT(16)
>> +#define GPIO_CLK_DIV_MASK GENMASK(11, 8)
>> +#define GPIO_USE_SAMPLE_DLY_MASK GENMASK(13, 13)
>> +#define UHS_REG_EXT_SAMPLE_PHASE_MASK GENMASK(20, 16)
>> +#define UHS_REG_EXT_SAMPLE_DRVPHASE_MASK GENMASK(25, 21)
>> +#define UHS_REG_EXT_SAMPLE_DLY_MASK GENMASK(30, 26)
>> +
>> +#define SDMMC_UHS_REG_EXT 0x108
>> +#define SDMMC_ENABLE_SHIFT 0x110
>> +
>> +#define TIMING_MODE 3
>> +#define TIMING_CFG_NUM 10
>> +
>> +#define PULL_DOWN BIT(1)
>> +#define PULL_UP BIT(0)
>> +
>> +#define NUM_PHASES (40)
>> +
>> +#define ENABLE_SHIFT_MIN_SMPL (4)
>> +#define ENABLE_SHIFT_MAX_SMPL (12)
>> +#define USE_DLY_MIN_SMPL (11)
>> +#define USE_DLY_MAX_SMPL (14)
>> +
>> struct k3_priv {
>> + u8 ctrl_id;
>> + u32 cur_speed;
>> struct regmap *reg;
>> };
>>
>> @@ -38,6 +73,41 @@ static unsigned long dw_mci_hi6220_caps[] = {
>> 0
>> };
>>
>> +struct hs_timing {
>> + int drv_phase;
>> + int sam_dly;
>> + int sam_phase_max;
>> + int sam_phase_min;
>> +};
>> +
>> +struct hs_timing hs_timing_cfg[TIMING_MODE][TIMING_CFG_NUM] = {
>> + { /* reserved */ },
>> + { /* SD */
>> + {7, 0, 15, 15,}, /* 0: LEGACY 400k */
>> + {6, 0, 4, 4,}, /* 1: MMC_HS */
>> + {6, 0, 3, 3,}, /* 2: SD_HS */
>> + {6, 0, 15, 15,}, /* 3: SDR12 */
>> + {6, 0, 2, 2,}, /* 4: SDR25 */
>> + {4, 0, 11, 0,}, /* 5: SDR50 */
>> + {6, 4, 15, 0,}, /* 6: SDR104 */
>> + {0}, /* 7: DDR50 */
>> + {0}, /* 8: DDR52 */
>> + {0}, /* 9: HS200 */
>> + },
>> + { /* SDIO */
>> + {7, 0, 15, 15,}, /* 0: LEGACY 400k */
>> + {0}, /* 1: MMC_HS */
>> + {6, 0, 15, 15,}, /* 2: SD_HS */
>> + {6, 0, 15, 15,}, /* 3: SDR12 */
>> + {6, 0, 0, 0,}, /* 4: SDR25 */
>> + {4, 0, 12, 0,}, /* 5: SDR50 */
>> + {5, 4, 15, 0,}, /* 6: SDR104 */
>> + {0}, /* 7: DDR50 */
>> + {0}, /* 8: DDR52 */
>> + {0}, /* 9: HS200 */
>> + }
>> +};
>> +
>> static void dw_mci_k3_set_ios(struct dw_mci *host, struct mmc_ios *ios)
>> {
>> int ret;
>> @@ -66,6 +136,10 @@ static int dw_mci_hi6220_parse_dt(struct dw_mci *host)
>> if (IS_ERR(priv->reg))
>> priv->reg = NULL;
>>
>> + priv->ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
>> + if (priv->ctrl_id < 0)
>> + priv->ctrl_id = 0;
>> +
>> host->priv = priv;
>> return 0;
>> }
>> @@ -144,7 +218,242 @@ static const struct dw_mci_drv_data hi6220_data = {
>> .execute_tuning = dw_mci_hi6220_execute_tuning,
>> };
>>
>> +static void dw_mci_hs_set_timing(struct dw_mci *host, int timing, int sam_phase)
>> +{
>> + int drv_phase;
>> + int sam_dly;
>> + int ctrl_id;
>> + int use_sam_dly = 0;
>> + int enable_shift = 0;
>> + int reg_value;
>> + struct k3_priv *priv;
>> +
>> + priv = host->priv;
>> + ctrl_id = priv->ctrl_id;
>> +
>> + drv_phase = hs_timing_cfg[ctrl_id][timing].drv_phase;
>> + sam_dly = hs_timing_cfg[ctrl_id][timing].sam_dly;
>> + if (sam_phase == -1)
>> + sam_phase = (hs_timing_cfg[ctrl_id][timing].sam_phase_max +
>> + hs_timing_cfg[ctrl_id][timing].sam_phase_min) / 2;
>> +
>> + if (timing == MMC_TIMING_UHS_SDR50 ||
>> + timing == MMC_TIMING_UHS_SDR104) {
>> + if (sam_phase >= ENABLE_SHIFT_MIN_SMPL &&
>> + sam_phase <= ENABLE_SHIFT_MAX_SMPL)
>> + enable_shift = 1;
>> + }
>> + if (timing == MMC_TIMING_UHS_SDR104) {
>> + if (sam_phase >= USE_DLY_MIN_SMPL &&
>> + sam_phase <= USE_DLY_MAX_SMPL)
>> + use_sam_dly = 1;
>> + }
>> +
>> + mci_writel(host, GPIO, 0x0);
>> + usleep_range(5, 10);
>> +
>> + reg_value = FIELD_PREP(UHS_REG_EXT_SAMPLE_PHASE_MASK, sam_phase) |\
>> + FIELD_PREP(UHS_REG_EXT_SAMPLE_DLY_MASK ,sam_dly) |\
>> + FIELD_PREP(UHS_REG_EXT_SAMPLE_DRVPHASE_MASK,drv_phase);
>> + mci_writel(host, UHS_REG_EXT, reg_value);
>> +
>> + mci_writel(host, ENABLE_SHIFT, enable_shift);
>> +
>> + reg_value = FIELD_PREP(GPIO_CLK_DIV_MASK, GENCLK_DIV) |\
>> + FIELD_PREP(GPIO_USE_SAMPLE_DLY_MASK,use_sam_dly);
>> + mci_writel(host, GPIO, (unsigned int)reg_value | GPIO_CLK_ENABLE);
>> +
>> + /* We should delay 1ms wait for timing setting finished. */
>> + usleep_range(1000, 2000);
>> +}
>> +
>> +int dw_mci_hi3660_init(struct dw_mci *host)
>> +{
>> + /* set threshold to 512 bytes */
>> + mci_writel(host, CDTHRCTL, 0x02000001);
>> +
>> + dw_mci_hs_set_timing(host, MMC_TIMING_LEGACY, -1);
>> + host->bus_hz /= (GENCLK_DIV + 1);
>> +
>> + return 0;
>> +}
>> +
>> +static int dw_mci_set_sel18(struct dw_mci *host, bool set)
>> +{
>> + int ret;
>> + unsigned int val;
>> + struct k3_priv *priv;
>> +
>> + priv = host->priv;
>> +
>> + val = set ? SDCARD_IO_SEL18 : 0;
>> + ret = regmap_update_bits(priv->reg, SOC_SCTRL_SCPERCTRL5,
>> + SDCARD_IO_SEL18, val);
>> + if (ret) {
>> + dev_err(host->dev, "sel18 %u error\n", val);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +void dw_mci_hi3660_set_ios(struct dw_mci *host, struct mmc_ios *ios)
>> +{
>> + int ret;
>> + unsigned long wanted;
>> + unsigned long actual;
>> + struct k3_priv *priv = host->priv;
>> +
>> + if (!ios->clock || ios->clock == priv->cur_speed)
>> + return;
>> +
>> + wanted = ios->clock * (GENCLK_DIV + 1);
>> + ret = clk_set_rate(host->ciu_clk, wanted);
>> + if (ret) {
>> + dev_err(host->dev, "failed to set rate %luHz\n", wanted);
>> + return;
>> + }
>> + actual = clk_get_rate(host->ciu_clk);
>> +
>> + dw_mci_hs_set_timing(host, ios->timing, -1);
>> + host->bus_hz = actual / (GENCLK_DIV + 1);
>> + host->current_speed = 0;
>> + priv->cur_speed = host->bus_hz;
>> +}
>> +
>> +static int dw_mci_get_best_clksmpl(unsigned int sample_flag)
>> +{
>> + int i;
>> + int interval;
>> + unsigned int v;
>> + unsigned int len;
>> + unsigned int range_start = 0;
>> + unsigned int range_length = 0;
>> + unsigned int middle_range = 0;
>> +
>> + if (!sample_flag)
>> + return -EIO;
>> +
>> + if (~sample_flag == 0)
>> + return 0;
>> +
>> + i = ffs(sample_flag) - 1;
>> +
>> + /*A clock cycle is divided into 32 phases,
>> + *each of which is represented by a bit, finding the optimal phase.
>> + */
>> + while (i < 32) {
>> + v = ror32(sample_flag, i);
>> + len = ffs(~v) - 1;
>> +
>> + if (len > range_length) {
>> + range_length = len;
>> + range_start = i;
>> + }
>> +
>> + interval = ffs(v >> len) - 1;
>> + if (interval < 0)
>> + break;
>> +
>> + i += len + interval;
>> + }
>> +
>> + middle_range = range_start + range_length / 2;
>> + if (middle_range >= 32)
>> + middle_range %= 32;
>> +
>> + return middle_range;
>> +}
>> +
>> +static int dw_mci_hi3660_execute_tuning(struct dw_mci_slot *slot, u32 opcode)
>> +{
>> + int i = 0;
>> + struct dw_mci *host = slot->host;
>> + struct mmc_host *mmc = slot->mmc;
>> + int sam_phase = 0;
>> + u32 tuning_sample_flag = 0;
>> + int best_clksmpl = 0;
>> +
>> + for (i = 0; i < NUM_PHASES; ++i, ++sam_phase) {
>> + sam_phase %= 32;
>> +
>> + mci_writel(host, TMOUT, ~0);
>> + dw_mci_hs_set_timing(host, mmc->ios.timing, sam_phase);
>> +
>> + if (!mmc_send_tuning(mmc, opcode, NULL))
>> + tuning_sample_flag |= (1 << sam_phase);
>> + else
>> + tuning_sample_flag &= ~(1 << sam_phase);
>> + }
>> +
>> + best_clksmpl = dw_mci_get_best_clksmpl(tuning_sample_flag);
>> + if (best_clksmpl < 0) {
>> + dev_err(host->dev, "All phases bad!\n");
>> + return -EIO;
>> + }
>> +
>> + dw_mci_hs_set_timing(host, mmc->ios.timing, best_clksmpl);
>> +
>> + dev_info(host->dev, "tuning ok best_clksmpl %u tuning_sample_flag %x\n",
>> + best_clksmpl, tuning_sample_flag);
>> + return 0;
>> +}
>> +
>> +static int dw_mci_hi3660_switch_voltage(struct mmc_host *mmc,
>> + struct mmc_ios *ios)
>> +{
>> + int ret;
>> + int min_uv = 0;
>> + int max_uv = 0;
>> + struct dw_mci_slot *slot = mmc_priv(mmc);
>> + struct k3_priv *priv;
>> + struct dw_mci *host;
>> +
>> + host = slot->host;
>> + priv = host->priv;
>> +
>> + if (!priv || !priv->reg)
>> + return 0;
>> +
>> + if (priv->ctrl_id == DWMMC_SDIO_ID)
>> + return 0;
>> +
>> + if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
>> + ret = dw_mci_set_sel18(host, 0);
>> + if (ret)
>> + return ret;
>> + min_uv = 2950000;
>> + max_uv = 2950000;
>> + } else if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
>> + ret = dw_mci_set_sel18(host, 1);
>> + if (ret)
>> + return ret;
>> + min_uv = 1800000;
>> + max_uv = 1800000;
>> + }
>> +
>> + if (IS_ERR_OR_NULL(mmc->supply.vqmmc))
>> + return 0;
>> +
>> + ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv);
>> + if (ret) {
>> + dev_dbg(host->dev, "Regulator set error %d: %d - %d\n",
>> + ret, min_uv, max_uv);
>> + return ret;
>> + }
>> + return 0;
>> +}
>> +
>> +static const struct dw_mci_drv_data hi3660_data = {
>> + .init = dw_mci_hi3660_init,
>> + .set_ios = dw_mci_hi3660_set_ios,
>> + .parse_dt = dw_mci_hi6220_parse_dt,
>> + .execute_tuning = dw_mci_hi3660_execute_tuning,
>> + .switch_voltage = dw_mci_hi3660_switch_voltage,
>> +};
>> +
>> static const struct of_device_id dw_mci_k3_match[] = {
>> + { .compatible = "hisilicon,hi3660-dw-mshc", .data = &hi3660_data, },
>> { .compatible = "hisilicon,hi4511-dw-mshc", .data = &k3_drv_data, },
>> { .compatible = "hisilicon,hi6220-dw-mshc", .data = &hi6220_data, },
>> {},
>> @@ -155,6 +464,11 @@ static int dw_mci_k3_probe(struct platform_device *pdev)
>> {
>> const struct dw_mci_drv_data *drv_data;
>> const struct of_device_id *match;
>> + struct reset_control *rst;
>> +
>> + rst = devm_reset_control_get(&pdev->dev, NULL);
>> + if (!IS_ERR(rst))
>> + reset_control_reset(rst);
>>
>> match = of_match_node(dw_mci_k3_match, pdev->dev.of_node);
>> drv_data = match->data;
>>
>
>
>