From: John Crispin <[email protected]>
Add basic support for Airoha EN7523, enough for booting to console.
The UART is basically 8250-compatible, except for the clock selection.
A clock-frequency value is synthesized to get this to run at 115200 bps.
Signed-off-by: John Crispin <[email protected]>
Signed-off-by: Bert Vermeulen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/en7523-evb.dts | 27 ++++++++
arch/arm/boot/dts/en7523.dtsi | 114 +++++++++++++++++++++++++++++++
3 files changed, 143 insertions(+)
create mode 100644 arch/arm/boot/dts/en7523-evb.dts
create mode 100644 arch/arm/boot/dts/en7523.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..81cb49f8d6fd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -186,6 +186,8 @@ dtb-$(CONFIG_ARCH_DAVINCI) += \
da850-lego-ev3.dtb
dtb-$(CONFIG_ARCH_DIGICOLOR) += \
cx92755_equinox.dtb
+dtb-$(CONFIG_ARCH_AIROHA) += \
+ en7523-evb.dtb
dtb-$(CONFIG_ARCH_EXYNOS3) += \
exynos3250-artik5-eval.dtb \
exynos3250-monk.dtb \
diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
new file mode 100644
index 000000000000..69754ef9a628
--- /dev/null
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+/* Bootloader installs ATF here */
+/memreserve/ 0x80000000 0x200000;
+
+#include "en7523.dtsi"
+
+/ {
+ model = "Airoha EN7523 Evaluation Board";
+ compatible = "airoha,en7523-evb", "airoha,en7523";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlycon";
+ stdout-path = "serial0:115200n8";
+ linux,usable-memory-range = <0x80200000 0x1fe00000>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
new file mode 100644
index 000000000000..7e17311a3f90
--- /dev/null
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ npu_binary@84000000 {
+ no-map;
+ reg = <0x84000000 0xA00000>;
+ };
+
+ npu_flag@84B0000 {
+ no-map;
+ reg = <0x84B00000 0x100000>;
+ };
+
+ npu_pkt@85000000 {
+ no-map;
+ reg = <0x85000000 0x1A00000>;
+ };
+
+ npu_phyaddr@86B00000 {
+ no-map;
+ reg = <0x86B00000 0x100000>;
+ };
+
+ npu_rxdesc@86D00000 {
+ no-map;
+ reg = <0x86D00000 0x100000>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ enable-method = "psci";
+ clock-frequency = <80000000>;
+ next-level-cache = <&L2_0>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ enable-method = "psci";
+ clock-frequency = <80000000>;
+ next-level-cache = <&L2_0>;
+ };
+
+ L2_0: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ gic: interrupt-controller@9000000 {
+ compatible = "arm,gic-v3";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x09000000 0x20000>, <0x09080000 0x80000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ clock-frequency = <25000000>;
+ };
+
+ uart1: serial@1fbf0000 {
+ compatible = "ns16550";
+ reg = <0x1fbf0000 0x30>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <1843200>;
+ status = "okay";
+ };
+};
--
2.34.1
On 2021-12-21 16:02, Marc Zyngier wrote:
> On 2021-12-20 21:18, Felix Fietkau wrote:
>> From: John Crispin <[email protected]>
>>
>> Add basic support for Airoha EN7523, enough for booting to console.
>>
>> The UART is basically 8250-compatible, except for the clock selection.
>> A clock-frequency value is synthesized to get this to run at 115200
>> bps.
>>
>> Signed-off-by: John Crispin <[email protected]>
>> Signed-off-by: Bert Vermeulen <[email protected]>
>> Signed-off-by: Felix Fietkau <[email protected]>
>> ---
>> arch/arm/boot/dts/Makefile | 2 +
>> arch/arm/boot/dts/en7523-evb.dts | 27 ++++++++
>> arch/arm/boot/dts/en7523.dtsi | 114 +++++++++++++++++++++++++++++++
>> 3 files changed, 143 insertions(+)
>> create mode 100644 arch/arm/boot/dts/en7523-evb.dts
>> create mode 100644 arch/arm/boot/dts/en7523.dtsi
>>
>
> [...]
>
>> + gic: interrupt-controller@9000000 {
>> + compatible = "arm,gic-v3";
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + reg = <0x09000000 0x20000>, <0x09080000 0x80000>;
>
> You are missing the 3 extra regions implemented by the A53 cores
> (GICC, GICV, GICH). Please see the binding and the A53 TRM.
The SoC memory map documentation contains an address for GICC, but not
for the other two. Maybe this CPU doesn't implement them.
I will add GICC in v9
>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
>> + };
>> +
>> + timer {
>> + compatible = "arm,armv7-timer";
>
> This is an ARMv8 CPU, even when used in 32bit mode.
>
>> + interrupt-parent = <&gic>;
>> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
>> + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
>> + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
>> + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
>> + clock-frequency = <25000000>;
>
> Why isn't this properly configured by the firmware?
I don't know.
- Felix