This series adds new bindings and a device-tree file for the Tanix TX5 Max
set-top box.
Christian Hewitt (2):
dt-bindings: arm: amlogic: add support for the Tanix TX5 Max
arm64: dts: meson-g12a-tanix-tx5max: add initial device tree
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12a-tanix-tx5max.dts | 481 +++++++++++++++++++++
3 files changed, 483 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
--
2.7.4
The Oranth (Tanix) TX5 Max is based on the Amlogic U200 reference
board with an S905X2 chip.
Signed-off-by: Christian Hewitt <[email protected]>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index f74aba4..4003206 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -136,6 +136,7 @@ properties:
- amediatech,x96-max
- amlogic,u200
- seirobotics,sei510
+ - oranth,tx5-max
- const: amlogic,g12a
- description: Boards with the Amlogic Meson G12B A311D SoC
--
2.7.4
The Oranth Tanix TX5 Max is based on the Amlogic U200 reference design
using the S905X2 chipset. Hardware specification:
- 4GB LPDDR4 RAM
- 32GB eMMC storage
- 10/100/1000 Base-T Ethernet using External RGMII PHY
- 802.11 a/b/g/b/ac + BT 4.1 sdio wireless
- HDMI 2.0 (4k@60p) video
- Composite video + 2-channel audio output on 3.5mm jack
- S/PDIF audio output
- 1x USB 3.0
- 1x USB 2.0
- 1x micro SD card slot
The device tree is based on the higher-spec X96 Max box device.
Signed-off-by: Christian Hewitt <[email protected]>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12a-tanix-tx5max.dts | 481 +++++++++++++++++++++
2 files changed, 482 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index eef0045..a1db803 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
new file mode 100644
index 0000000..c3ef0ee
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
@@ -0,0 +1,481 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 BayLibre SAS. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-g12a.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "oranth,tx5-max", "amlogic,g12a";
+ model = "Tanix TX5 Max";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ spdif_dit: audio-codec-1 {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ status = "okay";
+ sound-name-prefix = "DIT";
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ flash_1v8: regulator-flash_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "FLASH_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ dc_in: regulator-dc_in {
+ compatible = "regulator-fixed";
+ regulator-name = "DC_IN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_in>;
+
+ gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+ enable-active-low;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_in>;
+ regulator-always-on;
+ };
+
+ vddcpu: regulator-vddcpu {
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&dc_in>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "G12A-TANIX-TX5MAX";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "SPDIFOUT IN 0", "FRDDR_A OUT 3",
+ "SPDIFOUT IN 1", "FRDDR_B OUT 3",
+ "SPDIFOUT IN 2", "FRDDR_C OUT 3";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* spdif hdmi or toslink interface */
+ dai-link-4 {
+ sound-dai = <&spdifout>;
+
+ codec-0 {
+ sound-dai = <&spdif_dit>;
+ };
+
+ codec-1 {
+ sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_A>;
+ };
+ };
+
+ /* spdif hdmi interface */
+ dai-link-5 {
+ sound-dai = <&spdifout_b>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-6 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+ linux,rc-map-name = "rc-tx5max";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
+&ext_mdio {
+ external_phy: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ max-speed = <1000>;
+ eee-broken-1000t;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_14 */
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+ðmac {
+ pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "host";
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_1v8>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <100000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&flash_1v8>;
+};
+
+&spdifout {
+ pinctrl-0 = <&spdif_out_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&spdifout_b {
+ status = "okay";
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
--
2.7.4
On 29/02/2020 16:46, Christian Hewitt wrote:
> The Oranth Tanix TX5 Max is based on the Amlogic U200 reference design
> using the S905X2 chipset. Hardware specification:
>
> - 4GB LPDDR4 RAM
> - 32GB eMMC storage
> - 10/100/1000 Base-T Ethernet using External RGMII PHY
> - 802.11 a/b/g/b/ac + BT 4.1 sdio wireless
> - HDMI 2.0 (4k@60p) video
> - Composite video + 2-channel audio output on 3.5mm jack
> - S/PDIF audio output
> - 1x USB 3.0
> - 1x USB 2.0
> - 1x micro SD card slot
>
> The device tree is based on the higher-spec X96 Max box device.
>
> Signed-off-by: Christian Hewitt <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../boot/dts/amlogic/meson-g12a-tanix-tx5max.dts | 481 +++++++++++++++++++++
> 2 files changed, 482 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index eef0045..a1db803 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,6 +1,7 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
> new file mode 100644
> index 0000000..c3ef0ee
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
> @@ -0,0 +1,481 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2018 BayLibre SAS. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-g12a.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/gpio/meson-g12a-gpio.h>
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> + compatible = "oranth,tx5-max", "amlogic,g12a";
> + model = "Tanix TX5 Max";
> +
> + aliases {
> + serial0 = &uart_AO;
> + ethernet0 = ðmac;
> + };
> +
> + spdif_dit: audio-codec-1 {
> + #sound-dai-cells = <0>;
> + compatible = "linux,spdif-dit";
> + status = "okay";
> + sound-name-prefix = "DIT";
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x40000000>;
> + };
> +
> + cvbs-connector {
> + compatible = "composite-video-connector";
> +
> + port {
> + cvbs_connector_in: endpoint {
> + remote-endpoint = <&cvbs_vdac_out>;
> + };
> + };
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_tmds_out>;
> + };
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + flash_1v8: regulator-flash_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "FLASH_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + dc_in: regulator-dc_in {
> + compatible = "regulator-fixed";
> + regulator-name = "DC_IN";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v8: regulator-vcc_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + /* FIXME: actually controlled by VDDCPU_B_EN */
> + };
> +
> + vcc_5v: regulator-vcc_5v {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_in>;
> +
> + gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
> + enable-active-low;
> + };
> +
> + vddao_1v8: regulator-vddao_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&dc_in>;
> + regulator-always-on;
> + };
> +
> + vddcpu: regulator-vddcpu {
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU";
> + regulator-min-microvolt = <721000>;
> + regulator-max-microvolt = <1022000>;
> +
> + vin-supply = <&dc_in>;
> +
> + pwms = <&pwm_AO_cd 1 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "amlogic,axg-sound-card";
> + model = "G12A-TANIX-TX5MAX";
> + audio-aux-devs = <&tdmout_b>;
> + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> + "TDMOUT_B IN 1", "FRDDR_B OUT 1",
> + "TDMOUT_B IN 2", "FRDDR_C OUT 1",
> + "TDM_B Playback", "TDMOUT_B OUT",
> + "SPDIFOUT IN 0", "FRDDR_A OUT 3",
> + "SPDIFOUT IN 1", "FRDDR_B OUT 3",
> + "SPDIFOUT IN 2", "FRDDR_C OUT 3";
> +
> + assigned-clocks = <&clkc CLKID_MPLL2>,
> + <&clkc CLKID_MPLL0>,
> + <&clkc CLKID_MPLL1>;
> + assigned-clock-parents = <0>, <0>, <0>;
> + assigned-clock-rates = <294912000>,
> + <270950400>,
> + <393216000>;
> + status = "okay";
> +
> + dai-link-0 {
> + sound-dai = <&frddr_a>;
> + };
> +
> + dai-link-1 {
> + sound-dai = <&frddr_b>;
> + };
> +
> + dai-link-2 {
> + sound-dai = <&frddr_c>;
> + };
> +
> + /* 8ch hdmi interface */
> + dai-link-3 {
> + sound-dai = <&tdmif_b>;
> + dai-format = "i2s";
> + dai-tdm-slot-tx-mask-0 = <1 1>;
> + dai-tdm-slot-tx-mask-1 = <1 1>;
> + dai-tdm-slot-tx-mask-2 = <1 1>;
> + dai-tdm-slot-tx-mask-3 = <1 1>;
> + mclk-fs = <256>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> + };
> + };
> +
> + /* spdif hdmi or toslink interface */
> + dai-link-4 {
> + sound-dai = <&spdifout>;
> +
> + codec-0 {
> + sound-dai = <&spdif_dit>;
> + };
> +
> + codec-1 {
> + sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_A>;
> + };
> + };
> +
> + /* spdif hdmi interface */
> + dai-link-5 {
> + sound-dai = <&spdifout_b>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_B>;
> + };
> + };
> +
> + /* hdmi glue */
> + dai-link-6 {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> + codec {
> + sound-dai = <&hdmi_tx>;
> + };
> + };
> + };
> +
> + wifi32k: wifi32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +};
> +
> +&arb {
> + status = "okay";
> +};
> +
> +&cec_AO {
> + pinctrl-0 = <&cec_ao_a_h_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cecb_AO {
> + pinctrl-0 = <&cec_ao_b_h_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&clkc_audio {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cvbs_vdac_port {
> + cvbs_vdac_out: endpoint {
> + remote-endpoint = <&cvbs_connector_in>;
> + };
> +};
> +
> +&frddr_a {
> + status = "okay";
> +};
> +
> +&frddr_b {
> + status = "okay";
> +};
> +
> +&frddr_c {
> + status = "okay";
> +};
> +
> +&hdmi_tx {
> + status = "okay";
> + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
> + pinctrl-names = "default";
> + hdmi-supply = <&vcc_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> + hdmi_tx_tmds_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> +};
> +
> +&ir {
> + status = "okay";
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> + linux,rc-map-name = "rc-tx5max";
> +};
> +
> +&pwm_AO_cd {
> + pinctrl-0 = <&pwm_ao_d_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin1";
> + status = "okay";
> +};
> +
> +&ext_mdio {
> + external_phy: ethernet-phy@0 {
> + /* Realtek RTL8211F (0x001cc916) */
> + reg = <0>;
> + max-speed = <1000>;
> + eee-broken-1000t;
> +
> + reset-assert-us = <10000>;
> + reset-deassert-us = <30000>;
> + reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
> +
> + interrupt-parent = <&gpio_intc>;
> + /* MAC_INTR on GPIOZ_14 */
> + interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +ðmac {
> + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + phy-mode = "rgmii";
> + phy-handle = <&external_phy>;
> + amlogic,tx-delay-ns = <2>;
> +};
> +
> +&pwm_ef {
> + status = "okay";
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin0";
> +};
> +
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
> + max-speed = <2000000>;
> + clocks = <&wifi32k>;
> + clock-names = "lpo";
> + };
> +};
> +
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +/* SDIO */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + max-frequency = <100000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + /* WiFi firmware requires power to be kept while in suspend */
> + keep-power-in-suspend;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_1v8>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_c_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_c_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_3v3>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + max-frequency = <100000000>;
> + non-removable;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&flash_1v8>;
> +};
> +
> +&spdifout {
> + pinctrl-0 = <&spdif_out_h_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&spdifout_b {
> + status = "okay";
> +};
> +
> +&tdmif_b {
> + status = "okay";
> +};
> +
> +&tdmout_b {
> + status = "okay";
> +};
> +
> +&tohdmitx {
> + status = "okay";
> +};
>
Reviewed-by: Neil Armstrong <[email protected]>
On 29/02/2020 16:46, Christian Hewitt wrote:
> The Oranth (Tanix) TX5 Max is based on the Amlogic U200 reference
> board with an S905X2 chip.
>
> Signed-off-by: Christian Hewitt <[email protected]>
> ---
> Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
> index f74aba4..4003206 100644
> --- a/Documentation/devicetree/bindings/arm/amlogic.yaml
> +++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
> @@ -136,6 +136,7 @@ properties:
> - amediatech,x96-max
> - amlogic,u200
> - seirobotics,sei510
> + - oranth,tx5-max
> - const: amlogic,g12a
>
> - description: Boards with the Amlogic Meson G12B A311D SoC
>
Reviewed-by: Neil Armstrong <[email protected]>
On Sat 29 Feb 2020 at 16:46, Christian Hewitt <[email protected]> wrote:
> The Oranth Tanix TX5 Max is based on the Amlogic U200 reference design
> using the S905X2 chipset. Hardware specification:
>
> - 4GB LPDDR4 RAM
> - 32GB eMMC storage
> - 10/100/1000 Base-T Ethernet using External RGMII PHY
> - 802.11 a/b/g/b/ac + BT 4.1 sdio wireless
> - HDMI 2.0 (4k@60p) video
> - Composite video + 2-channel audio output on 3.5mm jack
> - S/PDIF audio output
> - 1x USB 3.0
> - 1x USB 2.0
> - 1x micro SD card slot
>
> The device tree is based on the higher-spec X96 Max box device.
Would you mind pointing out the differences ?
Maybe I missed something, but do we really this dts ?
Can't this device directly use the x96 dt, or the u200 ?
All these boards, for which we don't have any documentation, add up
>
> Signed-off-by: Christian Hewitt <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../boot/dts/amlogic/meson-g12a-tanix-tx5max.dts | 481 +++++++++++++++++++++
> 2 files changed, 482 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index eef0045..a1db803 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,6 +1,7 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
> new file mode 100644
> index 0000000..c3ef0ee
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-tanix-tx5max.dts
> @@ -0,0 +1,481 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2018 BayLibre SAS. All rights reserved.
> + */
> +
> +/dts-v1/;
[...]
> +&spdifout_b {
> + status = "okay";
> +};
Why do you need this ?
This producer is dedicated to HDMI controller which does not support it
ATM. Also it is not even used in your sound card
Same goes for the x96 BTW.
> +
> +&tdmif_b {
> + status = "okay";
> +};
> +
> +&tdmout_b {
> + status = "okay";
> +};
> +
> +&tohdmitx {
> + status = "okay";
> +};
On Sat, 29 Feb 2020 19:46:53 +0400, Christian Hewitt wrote:
> The Oranth (Tanix) TX5 Max is based on the Amlogic U200 reference
> board with an S905X2 chip.
>
> Signed-off-by: Christian Hewitt <[email protected]>
> ---
> Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Acked-by: Rob Herring <[email protected]>
Christian Hewitt <[email protected]> writes:
> The Oranth Tanix TX5 Max is based on the Amlogic U200 reference design
> using the S905X2 chipset. Hardware specification:
Similiar with the other new boards being submitted. Can you make a
U20[01] .dtsi to share between all these common designs?
Thanks,
Kevin