Usually, the vbus_regulator (smps10 on omap5evm) boots up disabled.
Hence calling regulator_disable() indirectly through dwc3_omap_set_mailbox()
during probe leads to:
[ 10.332764] WARNING: CPU: 0 PID: 1628 at drivers/regulator/core.c:2853 _regulator_disable+0x40/0x164
[ 10.351919] unbalanced disables for smps10_out1
[ 10.361298] Modules linked in: dwc3_omap(+) clk_twl6040 at24 gpio_twl6040 palmas_gpadc palmas_pwrbutton
industrialio snd_soc_omap_mcbsp(+) snd_soc_ti_sdma display_connector ti_tpd12s015 drm leds_gpio
drm_panel_orientation_quirks ip_tables x_tables ipv6 autofs4
[ 10.387818] CPU: 0 PID: 1628 Comm: systemd-udevd Not tainted 5.17.0-rc1-letux-lpae+ #8139
[ 10.405129] Hardware name: Generic OMAP5 (Flattened Device Tree)
[ 10.411455] unwind_backtrace from show_stack+0x10/0x14
[ 10.416970] show_stack from dump_stack_lvl+0x40/0x4c
[ 10.422313] dump_stack_lvl from __warn+0xb8/0x170
[ 10.427377] __warn from warn_slowpath_fmt+0x70/0x9c
[ 10.432595] warn_slowpath_fmt from _regulator_disable+0x40/0x164
[ 10.439037] _regulator_disable from regulator_disable+0x30/0x64
[ 10.445382] regulator_disable from dwc3_omap_set_mailbox+0x8c/0xf0 [dwc3_omap]
[ 10.453116] dwc3_omap_set_mailbox [dwc3_omap] from dwc3_omap_probe+0x2b8/0x394 [dwc3_omap]
[ 10.467021] dwc3_omap_probe [dwc3_omap] from platform_probe+0x58/0xa8
[ 10.481762] platform_probe from really_probe+0x168/0x2fc
[ 10.481782] really_probe from __driver_probe_device+0xc4/0xd8
[ 10.481782] __driver_probe_device from driver_probe_device+0x24/0xa4
[ 10.503762] driver_probe_device from __driver_attach+0xc4/0xd8
[ 10.510018] __driver_attach from bus_for_each_dev+0x64/0xa0
[ 10.516001] bus_for_each_dev from bus_add_driver+0x148/0x1a4
[ 10.524880] bus_add_driver from driver_register+0xb4/0xf8
[ 10.530678] driver_register from do_one_initcall+0x90/0x1c4
[ 10.536661] do_one_initcall from do_init_module+0x4c/0x200
[ 10.536683] do_init_module from load_module+0x13dc/0x1910
[ 10.551159] load_module from sys_finit_module+0xc8/0xd8
[ 10.561319] sys_finit_module from __sys_trace_return+0x0/0x18
[ 10.561336] Exception stack(0xc344bfa8 to 0xc344bff0)
[ 10.561341] bfa0: b6fb5778 b6fab8d8 00000007 b6ecfbb8 00000000 b6ed0398
[ 10.561341] bfc0: b6fb5778 b6fab8d8 855c0500 0000017b 00020000 b6f9a3cc 00000000 b6fb5778
[ 10.595500] bfe0: bede18f8 bede18e8 b6ec9aeb b6dda1c2
[ 10.601345] ---[ end trace 0000000000000000 ]---
Fix this unnecessary warning by checking if the regulator is enabled.
Signed-off-by: H. Nikolaus Schaller <[email protected]>
---
drivers/usb/dwc3/dwc3-omap.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c
index e196673f5c64..efaf0db595f4 100644
--- a/drivers/usb/dwc3/dwc3-omap.c
+++ b/drivers/usb/dwc3/dwc3-omap.c
@@ -242,7 +242,7 @@ static void dwc3_omap_set_mailbox(struct dwc3_omap *omap,
break;
case OMAP_DWC3_ID_FLOAT:
- if (omap->vbus_reg)
+ if (omap->vbus_reg && regulator_is_enabled(omap->vbus_reg))
regulator_disable(omap->vbus_reg);
val = dwc3_omap_read_utmi_ctrl(omap);
val |= USBOTGSS_UTMI_OTG_CTRL_IDDIG;
--
2.33.0