Running kernel 2.6.24.3 on Debian Testing here..
Kernel config attached.
Problem(?) in question:
[ 19.130558] Intel machine check architecture supported.
[ 19.130560] Intel machine check reporting enabled on CPU#1.
[ 19.130977] CPU1: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping 06
[ 19.131428] Total of 2 processors activated (10883.20 BogoMIPS).
[ 19.131613] ENABLING IO-APIC IRQs
[ 19.131808] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561 native_smp_call_function_mask()
[ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
[ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
[ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
[ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
[ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
[ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
[ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
[ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
[ 19.142413] [<c054cc21>] setup_IO_APIC+0xdd1/0xf30
[ 19.142482] [<c02cf850>] vt_console_print+0x0/0x2c0
[ 19.142550] [<c011cdaa>] release_console_sem+0x1ba/0x1e0
[ 19.142619] [<c011d33b>] printk+0x1b/0x20
[ 19.142685] [<c05489fb>] native_smp_prepare_cpus+0x57b/0xac0
[ 19.142754] [<c01188b4>] set_cpus_allowed+0x44/0xa0
[ 19.142821] [<c0540700>] kernel_init+0x0/0x300
[ 19.142888] [<c0540752>] kernel_init+0x52/0x300
[ 19.142954] [<c0118d97>] finish_task_switch+0x27/0x80
[ 19.143022] [<c0119327>] schedule_tail+0x17/0x60
[ 19.143089] [<c0102bd2>] ret_from_fork+0x6/0x1c
[ 19.143155] [<c0540700>] kernel_init+0x0/0x300
[ 19.143222] [<c0540700>] kernel_init+0x0/0x300
[ 19.143288] [<c01038d3>] kernel_thread_helper+0x7/0x14
[ 19.143356] =======================
[ 19.244403] APIC timer registered as dummy, due to nmi_watchdog=1!
[ 19.244504] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 19.264560] Brought up 2 CPUs
Full dmesg output below:
[ 0.000000] Linux version 2.6.24.3 (root@machine_name) (gcc version 4.2.3 (Debian 4.2.3-1)) #1 SMP PREEMPT Tue Feb 26 04:15:02 EST 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfee0000 (usable)
[ 0.000000] BIOS-e820: 00000000cfee0000 - 00000000cfee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cfee3000 - 00000000cfef0000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] Warning only 4GB will be used.
[ 0.000000] Use a HIGHMEM64G enabled kernel.
[ 0.000000] 3200MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f3430
[ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 1048576
[ 0.000000] On node 0 totalpages: 1048576
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 6400 pages used for memmap
[ 0.000000] HighMem zone: 812800 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F7330, 0014 (r0 IntelR)
[ 0.000000] ACPI: RSDT CFEE3040, 0038 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP CFEE30C0, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT CFEE3180, 485D (r1 INTELR AWRDACPI 1000 MSFT 100000E)
[ 0.000000] ACPI: FACS CFEE0000, 0040
[ 0.000000] ACPI: MCFG CFEE7B40, 003C (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: APIC CFEE7A40, 0084 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: SSDT CFEE7BC0, 019E (r1 PmRef Cpu0Ist 3000 INTL 20041203)
[ 0.000000] ACPI: SSDT CFEE8050, 02F1 (r1 PmRef CpuPm 3000 INTL 20041203)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at d0000000 (gap: cff00000:10100000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
[ 0.000000] Kernel command line: auto BOOT_IMAGE=2.6.24.3-1 ro root=802 [email protected]/eth0,[email protected]/00:19:D1:6E:9D:43 nmi_watchdog=1
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2720.482 MHz processor.
[ 18.849054] Console: colour VGA+ 80x25
[ 18.849057] console [tty0] enabled
[ 18.851688] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 18.851914] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 18.991168] Memory: 3367044k/4194304k available (3253k kernel code, 38552k reserved, 1071k data, 224k init, 2489216k highmem)
[ 18.991225] virtual kernel memory layout:
[ 18.991226] fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB)
[ 18.991226] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 18.991227] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 18.991228] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 18.991228] .init : 0xc0540000 - 0xc0578000 ( 224 kB)
[ 18.991229] .data : 0xc042d514 - 0xc053930c (1071 kB)
[ 18.991230] .text : 0xc0100000 - 0xc042d514 (3253 kB)
[ 18.991541] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 18.991647] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 19.051640] Calibrating delay using timer specific routine.. 5443.06 BogoMIPS (lpj=2721534)
[ 19.051740] Mount-cache hash table entries: 512
[ 19.051871] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[ 19.051876] monitor/mwait feature present.
[ 19.051915] using mwait in idle threads.
[ 19.051955] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 19.052022] CPU: L2 cache: 4096K
[ 19.052060] CPU: Physical Processor ID: 0
[ 19.052099] CPU: Processor Core ID: 0
[ 19.052137] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[ 19.052141] Intel machine check architecture supported.
[ 19.052182] Intel machine check reporting enabled on CPU#0.
[ 19.052224] Compat vDSO mapped to ffffe000.
[ 19.052270] Checking 'hlt' instruction... OK.
[ 19.055927] Freeing SMP alternatives: 13k freed
[ 19.055966] ACPI: Core revision 20070126
[ 19.060026] CPU0: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping 06
[ 19.060133] Booting processor 1/1 eip 2000
[ 19.071017] Initializing CPU#1
[ 19.130541] Calibrating delay using timer specific routine.. 5440.13 BogoMIPS (lpj=2720069)
[ 19.130545] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[ 19.130548] monitor/mwait feature present.
[ 19.130550] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 19.130552] CPU: L2 cache: 4096K
[ 19.130553] CPU: Physical Processor ID: 0
[ 19.130554] CPU: Processor Core ID: 1
[ 19.130555] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[ 19.130558] Intel machine check architecture supported.
[ 19.130560] Intel machine check reporting enabled on CPU#1.
[ 19.130977] CPU1: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping 06
[ 19.131428] Total of 2 processors activated (10883.20 BogoMIPS).
[ 19.131613] ENABLING IO-APIC IRQs
[ 19.131808] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561 native_smp_call_function_mask()
[ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
[ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
[ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
[ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
[ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
[ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
[ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
[ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
[ 19.142413] [<c054cc21>] setup_IO_APIC+0xdd1/0xf30
[ 19.142482] [<c02cf850>] vt_console_print+0x0/0x2c0
[ 19.142550] [<c011cdaa>] release_console_sem+0x1ba/0x1e0
[ 19.142619] [<c011d33b>] printk+0x1b/0x20
[ 19.142685] [<c05489fb>] native_smp_prepare_cpus+0x57b/0xac0
[ 19.142754] [<c01188b4>] set_cpus_allowed+0x44/0xa0
[ 19.142821] [<c0540700>] kernel_init+0x0/0x300
[ 19.142888] [<c0540752>] kernel_init+0x52/0x300
[ 19.142954] [<c0118d97>] finish_task_switch+0x27/0x80
[ 19.143022] [<c0119327>] schedule_tail+0x17/0x60
[ 19.143089] [<c0102bd2>] ret_from_fork+0x6/0x1c
[ 19.143155] [<c0540700>] kernel_init+0x0/0x300
[ 19.143222] [<c0540700>] kernel_init+0x0/0x300
[ 19.143288] [<c01038d3>] kernel_thread_helper+0x7/0x14
[ 19.143356] =======================
[ 19.244403] APIC timer registered as dummy, due to nmi_watchdog=1!
[ 19.244504] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 19.264560] Brought up 2 CPUs
[ 19.264705] net_namespace: 64 bytes
[ 19.264950] NET: Registered protocol family 16
[ 19.265070] ACPI: bus type pci registered
[ 19.265115] PCI: Using MMCONFIG
[ 19.265517] Setting up standard PCI resources
[ 19.266222] mtrr: your CPUs had inconsistent variable MTRR settings
[ 19.266263] mtrr: probably your BIOS does not setup all CPUs.
[ 19.266303] mtrr: corrected configuration.
[ 19.267455] ACPI: EC: Look up EC in DSDT
[ 19.270146] ACPI: Interpreter enabled
[ 19.270185] ACPI: (supports S0 S5)
[ 19.270280] ACPI: Using IOAPIC for interrupt routing
[ 19.273395] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 19.273774] Force enabled HPET at base address 0xfed00000
[ 19.273777] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 19.273819] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[ 19.274321] PCI: Transparent bridge - 0000:00:1e.0
[ 19.274379] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 19.274489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 19.274541] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
[ 19.274593] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 19.274645] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 19.282717] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 9 *10 11 12 14 15)
[ 19.283126] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 *5 7 9 10 11 12 14 15)
[ 19.283542] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 *7 9 10 11 12 14 15)
[ 19.283947] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 9 10 *11 12 14 15)
[ 19.284353] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 19.284827] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 19.285295] ACPI: PCI Interrupt Link [LNK0] (IRQs 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 19.285769] ACPI: PCI Interrupt Link [LNK1] (IRQs *4 5 7 9 10 11 12 14 15)
[ 19.286181] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 19.286237] pnp: PnP ACPI init
[ 19.286278] ACPI: bus type pnp registered
[ 19.287860] pnpacpi: exceeded the max number of mem resources: 12
[ 19.287936] pnp: PnP ACPI: found 13 devices
[ 19.287975] ACPI: ACPI bus type pnp unregistered
[ 19.288948] SCSI subsystem initialized
[ 19.289002] libata version 3.00 loaded.
[ 19.289059] usbcore: registered new interface driver usbfs
[ 19.289131] usbcore: registered new interface driver hub
[ 19.289193] usbcore: registered new device driver usb
[ 19.289321] PCI: Using ACPI for IRQ routing
[ 19.289360] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 19.293500] hpet clockevent registered
[ 19.293503] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 19.293652] hpet0: 3 64-bit timers, 14318180 Hz
[ 19.295500] Time: tsc clocksource has been installed.
[ 19.298518] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 19.298559] system 00:01: ioport range 0x880-0x88f has been reserved
[ 19.298604] system 00:08: ioport range 0x400-0x4bf could not be reserved
[ 19.298648] system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
[ 19.298700] system 00:0c: iomem range 0x636500-0xd1ccff could not be reserved
[ 19.298741] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved
[ 19.298783] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
[ 19.298824] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[ 19.298866] system 00:0c: iomem range 0xcfee0000-0xcfefffff could not be reserved
[ 19.298915] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 19.298957] system 00:0c: iomem range 0x100000-0xcfedffff could not be reserved
[ 19.299006] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 19.299055] system 00:0c: iomem range 0xfed13000-0xfed1dfff could not be reserved
[ 19.299105] system 00:0c: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 19.299154] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 19.299203] system 00:0c: iomem range 0xffb00000-0xffb7ffff could not be reserved
[ 19.329446] PCI: Bridge: 0000:00:01.0
[ 19.329489] IO window: b000-bfff
[ 19.329528] MEM window: f8000000-fbffffff
[ 19.329567] PREFETCH window: d0000000-dfffffff
[ 19.329607] PCI: Bridge: 0000:00:1c.0
[ 19.329645] IO window: a000-afff
[ 19.329685] MEM window: fda00000-fdafffff
[ 19.329724] PREFETCH window: fd700000-fd7fffff
[ 19.329765] PCI: Bridge: 0000:00:1c.2
[ 19.329803] IO window: e000-efff
[ 19.329843] MEM window: fde00000-fdefffff
[ 19.329882] PREFETCH window: fdd00000-fddfffff
[ 19.329923] PCI: Bridge: 0000:00:1c.4
[ 19.329961] IO window: d000-dfff
[ 19.330001] MEM window: fdc00000-fdcfffff
[ 19.330040] PREFETCH window: fdb00000-fdbfffff
[ 19.330081] PCI: Bridge: 0000:00:1e.0
[ 19.330119] IO window: c000-cfff
[ 19.330159] MEM window: fd900000-fd9fffff
[ 19.330198] PREFETCH window: fd800000-fd8fffff
[ 19.330243] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.330320] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.330330] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.330407] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 19.330417] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 17
[ 19.330499] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 19.330508] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.330586] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 19.330591] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 19.330597] NET: Registered protocol family 2
[ 19.340479] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 19.340640] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 19.340985] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 19.341234] TCP: Hash tables configured (established 131072 bind 65536)
[ 19.341276] TCP reno registered
[ 19.344975] highmem bounce pool size: 64 pages
[ 19.346480] Installing knfsd (copyright (C) 1996 [email protected]).
[ 19.346652] SGI XFS with no debug enabled
[ 19.347036] io scheduler noop registered
[ 19.347111] io scheduler cfq registered (default)
[ 19.347212] Boot video device is 0000:01:00.0
[ 19.347266] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.347277] assign_interrupt_mode Found MSI capability
[ 19.347326] Allocate Port Service[0000:00:01.0:pcie00]
[ 19.347346] Allocate Port Service[0000:00:01.0:pcie03]
[ 19.347379] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 19.347403] assign_interrupt_mode Found MSI capability
[ 19.347463] Allocate Port Service[0000:00:1c.0:pcie00]
[ 19.347483] Allocate Port Service[0000:00:1c.0:pcie02]
[ 19.347501] Allocate Port Service[0000:00:1c.0:pcie03]
[ 19.347546] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 19.347569] assign_interrupt_mode Found MSI capability
[ 19.347625] Allocate Port Service[0000:00:1c.2:pcie00]
[ 19.347645] Allocate Port Service[0000:00:1c.2:pcie02]
[ 19.347663] Allocate Port Service[0000:00:1c.2:pcie03]
[ 19.347710] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 19.347733] assign_interrupt_mode Found MSI capability
[ 19.347789] Allocate Port Service[0000:00:1c.4:pcie00]
[ 19.347808] Allocate Port Service[0000:00:1c.4:pcie02]
[ 19.347826] Allocate Port Service[0000:00:1c.4:pcie03]
[ 19.347956] input: Power Button (FF) as /devices/virtual/input/input0
[ 19.347997] ACPI: Power Button (FF) [PWRF]
[ 19.348078] input: Power Button (CM) as /devices/virtual/input/input1
[ 19.348119] ACPI: Power Button (CM) [PWRB]
[ 19.357494] Real Time Clock Driver v1.12ac
[ 19.357580] Linux agpgart interface v0.102
[ 19.357665] Floppy drive(s): fd0 is 1.44M
[ 19.372054] FDC 0 is a post-1991 82077
[ 19.373161] loop: module loaded
[ 19.373234] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 19.373275] Copyright (c) 1999-2006 Intel Corporation.
[ 19.373350] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.373436] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 19.429545] e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:1b:21:02:86:95
[ 19.486899] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 19.486947] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
[ 19.486987] e1000e: Copyright (c) 1999-2007 Intel Corporation.
[ 19.487052] netconsole: local port 4444
[ 19.487091] netconsole: local IP 192.168.0.1
[ 19.487129] netconsole: interface eth0
[ 19.487168] netconsole: remote port 514
[ 19.487206] netconsole: remote IP 192.168.0.254
[ 19.487246] netconsole: remote ethernet address 00:19:d1:6e:9d:43
[ 19.487287] netconsole: device eth0 not up yet, forcing it
[ 19.793953] Clockevents: could not switch to one-shot mode:<6>Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 19.793956] Could not switch to high resolution mode on CPU 1
[ 19.794073] lapic is not functional.
[ 19.794111] Could not switch to high resolution mode on CPU 0
[ 22.522434] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 22.524960] console [netcon0] enabled
[ 22.537821] netconsole: network logging started
[ 22.537892] Driver 'sd' needs updating - please use bus_type methods
[ 22.537954] Driver 'sr' needs updating - please use bus_type methods
[ 22.538040] ahci 0000:00:1f.2: version 3.0
[ 22.538052] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
[ 23.537862] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 23.537913] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 23.537956] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 23.538089] scsi0 : ahci
[ 23.538170] scsi1 : ahci
[ 23.538240] scsi2 : ahci
[ 23.538318] scsi3 : ahci
[ 23.538411] ata1: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe100 irq 218
[ 23.538463] ata2: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe180 irq 218
[ 23.538518] ata3: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe200 irq 218
[ 23.538573] ata4: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe280 irq 218
[ 23.993352] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 24.000089] ata1.00: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
[ 24.000131] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 24.000956] ata1.00: configured for UDMA/133
[ 24.455844] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 24.609697] ata2.00: ATAPI: TSSTcorpCD/DVDW SH-S183L, SB02, max UDMA/33, ATAPI AN
[ 24.609746] ata2.00: applying bridge limits
[ 24.763896] ata2.00: configured for UDMA/33
[ 25.066174] ata3: SATA link down (SStatus 0 SControl 300)
[ 25.368842] ata4: SATA link down (SStatus 0 SControl 300)
[ 25.368947] scsi 0:0:0:0: Direct-Access ATA WDC WD7500AAKS-0 30.0 PQ: 0 ANSI: 5
[ 25.369061] sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
[ 25.369117] sd 0:0:0:0: [sda] Write Protect is off
[ 25.369162] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.369171] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.369252] sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
[ 25.369309] sd 0:0:0:0: [sda] Write Protect is off
[ 25.369354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.369364] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.369419] sda: sda1 sda2
[ 25.374009] sd 0:0:0:0: [sda] Attached SCSI disk
[ 25.374905] scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB02 PQ: 0 ANSI: 5
[ 25.383411] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 25.383462] Uniform CD-ROM driver Revision: 3.20
[ 25.383558] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 25.383615] ata_piix 0000:00:1f.1: version 2.12
[ 25.383622] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
[ 25.383723] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 25.383756] scsi4 : ata_piix
[ 25.383834] scsi5 : ata_piix
[ 25.384178] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfb00 irq 14
[ 25.384220] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfb08 irq 15
[ 25.534721] ata6: port disabled. ignoring.
[ 25.545781] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 17 (level, low) -> IRQ 19
[ 25.595935] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[fd9ff000-fd9ff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 25.596066] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[ 25.596153] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 25.596155] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 25.596237] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 25.600172] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 25.600177] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfdfff000
[ 25.609576] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.609735] usb usb1: configuration #1 chosen from 1 choice
[ 25.609799] hub 1-0:1.0: USB hub found
[ 25.609847] hub 1-0:1.0: 8 ports detected
[ 25.710538] USB Universal Host Controller Interface driver v3.0
[ 25.710603] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
[ 25.710696] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 25.710698] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 25.710766] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 25.710839] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000ff00
[ 25.710970] usb usb2: configuration #1 chosen from 1 choice
[ 25.711034] hub 2-0:1.0: USB hub found
[ 25.711081] hub 2-0:1.0: 2 ports detected
[ 25.811418] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
[ 25.811498] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 25.811500] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 25.811567] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 25.811641] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000fe00
[ 25.811774] usb usb3: configuration #1 chosen from 1 choice
[ 25.811838] hub 3-0:1.0: USB hub found
[ 25.811885] hub 3-0:1.0: 2 ports detected
[ 25.912307] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
[ 25.912394] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 25.912395] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 25.912462] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 25.912542] uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000fd00
[ 25.912670] usb usb4: configuration #1 chosen from 1 choice
[ 25.912739] hub 4-0:1.0: USB hub found
[ 25.912780] hub 4-0:1.0: 2 ports detected
[ 26.013198] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 26.013284] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 26.013286] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 26.013354] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 26.013428] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[ 26.013562] usb usb5: configuration #1 chosen from 1 choice
[ 26.013625] hub 5-0:1.0: USB hub found
[ 26.013672] hub 5-0:1.0: 2 ports detected
[ 26.114089] Initializing USB Mass Storage driver...
[ 26.225899] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 26.395248] usb 2-2: configuration #1 chosen from 1 choice
[ 26.603485] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 26.766761] usb 3-1: configuration #1 chosen from 1 choice
[ 26.770797] usbcore: registered new interface driver usb-storage
[ 26.770839] USB Mass Storage support registered.
[ 26.770934] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 26.770976] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 26.771515] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 26.771603] mice: PS/2 mouse device common for all mice
[ 26.801022] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 26.803324] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 26.850285] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00508d0000994687]
[ 26.852373] abituguru3: found Abit uGuru3, motherboard ID: 0016 (AW9D-MAX)
[ 26.852819] coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
[ 26.852914] coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
[ 26.853014] usbcore: registered new interface driver hiddev
[ 26.867836] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input4
[ 26.870213] input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-2
[ 27.142344] hiddev96: USB HID v1.11 Device [Belkin Belkin UPS] on usb-0000:00:1d.1-1
[ 27.142461] usbcore: registered new interface driver usbhid
[ 27.142503] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 27.142570] Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC).
[ 27.143593] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 27.143681] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 27.194837] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 27.234870] ALSA device list:
[ 27.234909] #0: HDA Intel at 0xfdff8000 irq 16
[ 27.234950] TCP cubic registered
[ 27.235004] NET: Registered protocol family 1
[ 27.235057] NET: Registered protocol family 17
[ 27.235187] RPC: Registered udp transport module.
[ 27.235228] RPC: Registered tcp transport module.
[ 27.235275] Testing NMI watchdog ... OK.
[ 27.255332] Starting balanced_irq
[ 27.255383] Using IPI Shortcut mode
[ 27.285525] UDF-fs: No VRS found
[ 27.323228] XFS mounting filesystem sda2
[ 27.413136] Ending clean XFS mount for filesystem: sda2
[ 27.413153] VFS: Mounted root (xfs filesystem) readonly.
[ 27.413273] Freeing unused kernel memory: 224k freed
[ 29.727530] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 18
[ 31.260700] Adding 8393920k swap on /dev/sda1. Priority:-1 extents:1 across:8393920k
[ 49.957428] nvidia: module license 'NVIDIA' taints kernel.
[ 50.210535] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 50.210547] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 50.210639] NVRM: loading NVIDIA UNIX x86 Kernel Module 171.05 Tue Jan 22 18:08:39 PST 2008
Any comment/regarding this problem? Please cc me as I am not on the list,
thanks.
On Mon, 10 Mar 2008, Justin Piszcz wrote:
> Running kernel 2.6.24.3 on Debian Testing here..
> Kernel config attached.
>
> Problem(?) in question:
> [ 19.130558] Intel machine check architecture supported.
> [ 19.130560] Intel machine check reporting enabled on CPU#1.
> [ 19.130977] CPU1: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping
> 06
> [ 19.131428] Total of 2 processors activated (10883.20 BogoMIPS).
> [ 19.131613] ENABLING IO-APIC IRQs
> [ 19.131808] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561
> native_smp_call_function_mask()
> [ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
> [ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
> [ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
> [ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
> [ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
> [ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
> [ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
> [ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
> [ 19.142413] [<c054cc21>] setup_IO_APIC+0xdd1/0xf30
> [ 19.142482] [<c02cf850>] vt_console_print+0x0/0x2c0
> [ 19.142550] [<c011cdaa>] release_console_sem+0x1ba/0x1e0
> [ 19.142619] [<c011d33b>] printk+0x1b/0x20
> [ 19.142685] [<c05489fb>] native_smp_prepare_cpus+0x57b/0xac0
> [ 19.142754] [<c01188b4>] set_cpus_allowed+0x44/0xa0
> [ 19.142821] [<c0540700>] kernel_init+0x0/0x300
> [ 19.142888] [<c0540752>] kernel_init+0x52/0x300
> [ 19.142954] [<c0118d97>] finish_task_switch+0x27/0x80
> [ 19.143022] [<c0119327>] schedule_tail+0x17/0x60
> [ 19.143089] [<c0102bd2>] ret_from_fork+0x6/0x1c
> [ 19.143155] [<c0540700>] kernel_init+0x0/0x300
> [ 19.143222] [<c0540700>] kernel_init+0x0/0x300
> [ 19.143288] [<c01038d3>] kernel_thread_helper+0x7/0x14
> [ 19.143356] =======================
> [ 19.244403] APIC timer registered as dummy, due to nmi_watchdog=1!
> [ 19.244504] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
> [ 19.264560] Brought up 2 CPUs
>
> Full dmesg output below:
>
> [ 0.000000] Linux version 2.6.24.3 (root@machine_name) (gcc version 4.2.3
> (Debian 4.2.3-1)) #1 SMP PREEMPT Tue Feb 26 04:15:02 EST 2008
> [ 0.000000] BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
> [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
> [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfee0000 (usable)
> [ 0.000000] BIOS-e820: 00000000cfee0000 - 00000000cfee3000 (ACPI NVS)
> [ 0.000000] BIOS-e820: 00000000cfee3000 - 00000000cfef0000 (ACPI data)
> [ 0.000000] BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved)
> [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
> [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
> [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
> [ 0.000000] Warning only 4GB will be used.
> [ 0.000000] Use a HIGHMEM64G enabled kernel.
> [ 0.000000] 3200MB HIGHMEM available.
> [ 0.000000] 896MB LOWMEM available.
> [ 0.000000] found SMP MP-table at 000f3430
> [ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
> [ 0.000000] Zone PFN ranges:
> [ 0.000000] DMA 0 -> 4096
> [ 0.000000] Normal 4096 -> 229376
> [ 0.000000] HighMem 229376 -> 1048576
> [ 0.000000] Movable zone start PFN for each node
> [ 0.000000] early_node_map[1] active PFN ranges
> [ 0.000000] 0: 0 -> 1048576
> [ 0.000000] On node 0 totalpages: 1048576
> [ 0.000000] DMA zone: 32 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 4064 pages, LIFO batch:0
> [ 0.000000] Normal zone: 1760 pages used for memmap
> [ 0.000000] Normal zone: 223520 pages, LIFO batch:31
> [ 0.000000] HighMem zone: 6400 pages used for memmap
> [ 0.000000] HighMem zone: 812800 pages, LIFO batch:31
> [ 0.000000] Movable zone: 0 pages used for memmap
> [ 0.000000] DMI 2.2 present.
> [ 0.000000] ACPI: RSDP 000F7330, 0014 (r0 IntelR)
> [ 0.000000] ACPI: RSDT CFEE3040, 0038 (r1 IntelR AWRDACPI 42302E31 AWRD
> 0)
> [ 0.000000] ACPI: FACP CFEE30C0, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD
> 0)
> [ 0.000000] ACPI: DSDT CFEE3180, 485D (r1 INTELR AWRDACPI 1000 MSFT
> 100000E)
> [ 0.000000] ACPI: FACS CFEE0000, 0040
> [ 0.000000] ACPI: MCFG CFEE7B40, 003C (r1 IntelR AWRDACPI 42302E31 AWRD
> 0)
> [ 0.000000] ACPI: APIC CFEE7A40, 0084 (r1 IntelR AWRDACPI 42302E31 AWRD
> 0)
> [ 0.000000] ACPI: SSDT CFEE7BC0, 019E (r1 PmRef Cpu0Ist 3000 INTL
> 20041203)
> [ 0.000000] ACPI: SSDT CFEE8050, 02F1 (r1 PmRef CpuPm 3000 INTL
> 20041203)
> [ 0.000000] ACPI: PM-Timer IO Port: 0x408
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> [ 0.000000] Processor #0 6:15 APIC version 20
> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> [ 0.000000] Processor #1 6:15 APIC version 20
> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
> [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> [ 0.000000] ACPI: IRQ0 used by override.
> [ 0.000000] ACPI: IRQ2 used by override.
> [ 0.000000] ACPI: IRQ9 used by override.
> [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
> [ 0.000000] Using ACPI (MADT) for SMP configuration information
> [ 0.000000] Allocating PCI resources starting at d0000000 (gap:
> cff00000:10100000)
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
> pages: 1040384
> [ 0.000000] Kernel command line: auto BOOT_IMAGE=2.6.24.3-1 ro root=802
> [email protected]/eth0,[email protected]/00:19:D1:6E:9D:43
> nmi_watchdog=1
> [ 0.000000] mapped APIC to ffffb000 (fee00000)
> [ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
> [ 0.000000] Enabling fast FPU save and restore... done.
> [ 0.000000] Enabling unmasked SIMD FPU exception support... done.
> [ 0.000000] Initializing CPU#0
> [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
> [ 0.000000] Detected 2720.482 MHz processor.
> [ 18.849054] Console: colour VGA+ 80x25
> [ 18.849057] console [tty0] enabled
> [ 18.851688] Dentry cache hash table entries: 131072 (order: 7, 524288
> bytes)
> [ 18.851914] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> [ 18.991168] Memory: 3367044k/4194304k available (3253k kernel code, 38552k
> reserved, 1071k data, 224k init, 2489216k highmem)
> [ 18.991225] virtual kernel memory layout:
> [ 18.991226] fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB)
> [ 18.991226] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> [ 18.991227] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
> [ 18.991228] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
> [ 18.991228] .init : 0xc0540000 - 0xc0578000 ( 224 kB)
> [ 18.991229] .data : 0xc042d514 - 0xc053930c (1071 kB)
> [ 18.991230] .text : 0xc0100000 - 0xc042d514 (3253 kB)
> [ 18.991541] Checking if this processor honours the WP bit even in
> supervisor mode... Ok.
> [ 18.991647] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
> CPUs=2, Nodes=1
> [ 19.051640] Calibrating delay using timer specific routine.. 5443.06
> BogoMIPS (lpj=2721534)
> [ 19.051740] Mount-cache hash table entries: 512
> [ 19.051871] CPU: After generic identify, caps: bfebfbff 20100000 00000000
> 00000000 0000e3bd 00000000 00000001 00000000
> [ 19.051876] monitor/mwait feature present.
> [ 19.051915] using mwait in idle threads.
> [ 19.051955] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 19.052022] CPU: L2 cache: 4096K
> [ 19.052060] CPU: Physical Processor ID: 0
> [ 19.052099] CPU: Processor Core ID: 0
> [ 19.052137] CPU: After all inits, caps: bfebfbff 20100000 00000000
> 00003940 0000e3bd 00000000 00000001 00000000
> [ 19.052141] Intel machine check architecture supported.
> [ 19.052182] Intel machine check reporting enabled on CPU#0.
> [ 19.052224] Compat vDSO mapped to ffffe000.
> [ 19.052270] Checking 'hlt' instruction... OK.
> [ 19.055927] Freeing SMP alternatives: 13k freed
> [ 19.055966] ACPI: Core revision 20070126
> [ 19.060026] CPU0: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping
> 06
> [ 19.060133] Booting processor 1/1 eip 2000
> [ 19.071017] Initializing CPU#1
> [ 19.130541] Calibrating delay using timer specific routine.. 5440.13
> BogoMIPS (lpj=2720069)
> [ 19.130545] CPU: After generic identify, caps: bfebfbff 20100000 00000000
> 00000000 0000e3bd 00000000 00000001 00000000
> [ 19.130548] monitor/mwait feature present.
> [ 19.130550] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 19.130552] CPU: L2 cache: 4096K
> [ 19.130553] CPU: Physical Processor ID: 0
> [ 19.130554] CPU: Processor Core ID: 1
> [ 19.130555] CPU: After all inits, caps: bfebfbff 20100000 00000000
> 00003940 0000e3bd 00000000 00000001 00000000
> [ 19.130558] Intel machine check architecture supported.
> [ 19.130560] Intel machine check reporting enabled on CPU#1.
> [ 19.130977] CPU1: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping
> 06
> [ 19.131428] Total of 2 processors activated (10883.20 BogoMIPS).
> [ 19.131613] ENABLING IO-APIC IRQs
> [ 19.131808] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561
> native_smp_call_function_mask()
> [ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
> [ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
> [ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
> [ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
> [ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
> [ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
> [ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
> [ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
> [ 19.142413] [<c054cc21>] setup_IO_APIC+0xdd1/0xf30
> [ 19.142482] [<c02cf850>] vt_console_print+0x0/0x2c0
> [ 19.142550] [<c011cdaa>] release_console_sem+0x1ba/0x1e0
> [ 19.142619] [<c011d33b>] printk+0x1b/0x20
> [ 19.142685] [<c05489fb>] native_smp_prepare_cpus+0x57b/0xac0
> [ 19.142754] [<c01188b4>] set_cpus_allowed+0x44/0xa0
> [ 19.142821] [<c0540700>] kernel_init+0x0/0x300
> [ 19.142888] [<c0540752>] kernel_init+0x52/0x300
> [ 19.142954] [<c0118d97>] finish_task_switch+0x27/0x80
> [ 19.143022] [<c0119327>] schedule_tail+0x17/0x60
> [ 19.143089] [<c0102bd2>] ret_from_fork+0x6/0x1c
> [ 19.143155] [<c0540700>] kernel_init+0x0/0x300
> [ 19.143222] [<c0540700>] kernel_init+0x0/0x300
> [ 19.143288] [<c01038d3>] kernel_thread_helper+0x7/0x14
> [ 19.143356] =======================
> [ 19.244403] APIC timer registered as dummy, due to nmi_watchdog=1!
> [ 19.244504] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
> [ 19.264560] Brought up 2 CPUs
> [ 19.264705] net_namespace: 64 bytes
> [ 19.264950] NET: Registered protocol family 16
> [ 19.265070] ACPI: bus type pci registered
> [ 19.265115] PCI: Using MMCONFIG
> [ 19.265517] Setting up standard PCI resources
> [ 19.266222] mtrr: your CPUs had inconsistent variable MTRR settings
> [ 19.266263] mtrr: probably your BIOS does not setup all CPUs.
> [ 19.266303] mtrr: corrected configuration.
> [ 19.267455] ACPI: EC: Look up EC in DSDT
> [ 19.270146] ACPI: Interpreter enabled
> [ 19.270185] ACPI: (supports S0 S5)
> [ 19.270280] ACPI: Using IOAPIC for interrupt routing
> [ 19.273395] ACPI: PCI Root Bridge [PCI0] (0000:00)
> [ 19.273774] Force enabled HPET at base address 0xfed00000
> [ 19.273777] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
> [ 19.273819] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
> [ 19.274321] PCI: Transparent bridge - 0000:00:1e.0
> [ 19.274379] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 19.274489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
> [ 19.274541] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
> [ 19.274593] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
> [ 19.274645] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
> [ 19.282717] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 9 *10 11 12 14 15)
> [ 19.283126] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 *5 7 9 10 11 12 14 15)
> [ 19.283542] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 *7 9 10 11 12 14 15)
> [ 19.283947] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 9 10 *11 12 14 15)
> [ 19.284353] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> [ 19.284827] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> [ 19.285295] ACPI: PCI Interrupt Link [LNK0] (IRQs 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> [ 19.285769] ACPI: PCI Interrupt Link [LNK1] (IRQs *4 5 7 9 10 11 12 14 15)
> [ 19.286181] Linux Plug and Play Support v0.97 (c) Adam Belay
> [ 19.286237] pnp: PnP ACPI init
> [ 19.286278] ACPI: bus type pnp registered
> [ 19.287860] pnpacpi: exceeded the max number of mem resources: 12
> [ 19.287936] pnp: PnP ACPI: found 13 devices
> [ 19.287975] ACPI: ACPI bus type pnp unregistered
> [ 19.288948] SCSI subsystem initialized
> [ 19.289002] libata version 3.00 loaded.
> [ 19.289059] usbcore: registered new interface driver usbfs
> [ 19.289131] usbcore: registered new interface driver hub
> [ 19.289193] usbcore: registered new device driver usb
> [ 19.289321] PCI: Using ACPI for IRQ routing
> [ 19.289360] PCI: If a device doesn't work, try "pci=routeirq". If it
> helps, post a report
> [ 19.293500] hpet clockevent registered
> [ 19.293503] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
> [ 19.293652] hpet0: 3 64-bit timers, 14318180 Hz
> [ 19.295500] Time: tsc clocksource has been installed.
> [ 19.298518] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
> [ 19.298559] system 00:01: ioport range 0x880-0x88f has been reserved
> [ 19.298604] system 00:08: ioport range 0x400-0x4bf could not be reserved
> [ 19.298648] system 00:0b: iomem range 0xe0000000-0xefffffff could not be
> reserved
> [ 19.298700] system 00:0c: iomem range 0x636500-0xd1ccff could not be
> reserved
> [ 19.298741] system 00:0c: iomem range 0xf0000-0xf7fff could not be
> reserved
> [ 19.298783] system 00:0c: iomem range 0xf8000-0xfbfff could not be
> reserved
> [ 19.298824] system 00:0c: iomem range 0xfc000-0xfffff could not be
> reserved
> [ 19.298866] system 00:0c: iomem range 0xcfee0000-0xcfefffff could not be
> reserved
> [ 19.298915] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
> [ 19.298957] system 00:0c: iomem range 0x100000-0xcfedffff could not be
> reserved
> [ 19.299006] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be
> reserved
> [ 19.299055] system 00:0c: iomem range 0xfed13000-0xfed1dfff could not be
> reserved
> [ 19.299105] system 00:0c: iomem range 0xfed20000-0xfed8ffff could not be
> reserved
> [ 19.299154] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be
> reserved
> [ 19.299203] system 00:0c: iomem range 0xffb00000-0xffb7ffff could not be
> reserved
> [ 19.329446] PCI: Bridge: 0000:00:01.0
> [ 19.329489] IO window: b000-bfff
> [ 19.329528] MEM window: f8000000-fbffffff
> [ 19.329567] PREFETCH window: d0000000-dfffffff
> [ 19.329607] PCI: Bridge: 0000:00:1c.0
> [ 19.329645] IO window: a000-afff
> [ 19.329685] MEM window: fda00000-fdafffff
> [ 19.329724] PREFETCH window: fd700000-fd7fffff
> [ 19.329765] PCI: Bridge: 0000:00:1c.2
> [ 19.329803] IO window: e000-efff
> [ 19.329843] MEM window: fde00000-fdefffff
> [ 19.329882] PREFETCH window: fdd00000-fddfffff
> [ 19.329923] PCI: Bridge: 0000:00:1c.4
> [ 19.329961] IO window: d000-dfff
> [ 19.330001] MEM window: fdc00000-fdcfffff
> [ 19.330040] PREFETCH window: fdb00000-fdbfffff
> [ 19.330081] PCI: Bridge: 0000:00:1e.0
> [ 19.330119] IO window: c000-cfff
> [ 19.330159] MEM window: fd900000-fd9fffff
> [ 19.330198] PREFETCH window: fd800000-fd8fffff
> [ 19.330243] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) ->
> IRQ 16
> [ 19.330320] PCI: Setting latency timer of device 0000:00:01.0 to 64
> [ 19.330330] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) ->
> IRQ 16
> [ 19.330407] PCI: Setting latency timer of device 0000:00:1c.0 to 64
> [ 19.330417] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) ->
> IRQ 17
> [ 19.330499] PCI: Setting latency timer of device 0000:00:1c.2 to 64
> [ 19.330508] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) ->
> IRQ 16
> [ 19.330586] PCI: Setting latency timer of device 0000:00:1c.4 to 64
> [ 19.330591] PCI: Setting latency timer of device 0000:00:1e.0 to 64
> [ 19.330597] NET: Registered protocol family 2
> [ 19.340479] IP route cache hash table entries: 32768 (order: 5, 131072
> bytes)
> [ 19.340640] TCP established hash table entries: 131072 (order: 8, 1048576
> bytes)
> [ 19.340985] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> [ 19.341234] TCP: Hash tables configured (established 131072 bind 65536)
> [ 19.341276] TCP reno registered
> [ 19.344975] highmem bounce pool size: 64 pages
> [ 19.346480] Installing knfsd (copyright (C) 1996 [email protected]).
> [ 19.346652] SGI XFS with no debug enabled
> [ 19.347036] io scheduler noop registered
> [ 19.347111] io scheduler cfq registered (default)
> [ 19.347212] Boot video device is 0000:01:00.0
> [ 19.347266] PCI: Setting latency timer of device 0000:00:01.0 to 64
> [ 19.347277] assign_interrupt_mode Found MSI capability
> [ 19.347326] Allocate Port Service[0000:00:01.0:pcie00]
> [ 19.347346] Allocate Port Service[0000:00:01.0:pcie03]
> [ 19.347379] PCI: Setting latency timer of device 0000:00:1c.0 to 64
> [ 19.347403] assign_interrupt_mode Found MSI capability
> [ 19.347463] Allocate Port Service[0000:00:1c.0:pcie00]
> [ 19.347483] Allocate Port Service[0000:00:1c.0:pcie02]
> [ 19.347501] Allocate Port Service[0000:00:1c.0:pcie03]
> [ 19.347546] PCI: Setting latency timer of device 0000:00:1c.2 to 64
> [ 19.347569] assign_interrupt_mode Found MSI capability
> [ 19.347625] Allocate Port Service[0000:00:1c.2:pcie00]
> [ 19.347645] Allocate Port Service[0000:00:1c.2:pcie02]
> [ 19.347663] Allocate Port Service[0000:00:1c.2:pcie03]
> [ 19.347710] PCI: Setting latency timer of device 0000:00:1c.4 to 64
> [ 19.347733] assign_interrupt_mode Found MSI capability
> [ 19.347789] Allocate Port Service[0000:00:1c.4:pcie00]
> [ 19.347808] Allocate Port Service[0000:00:1c.4:pcie02]
> [ 19.347826] Allocate Port Service[0000:00:1c.4:pcie03]
> [ 19.347956] input: Power Button (FF) as /devices/virtual/input/input0
> [ 19.347997] ACPI: Power Button (FF) [PWRF]
> [ 19.348078] input: Power Button (CM) as /devices/virtual/input/input1
> [ 19.348119] ACPI: Power Button (CM) [PWRB]
> [ 19.357494] Real Time Clock Driver v1.12ac
> [ 19.357580] Linux agpgart interface v0.102
> [ 19.357665] Floppy drive(s): fd0 is 1.44M
> [ 19.372054] FDC 0 is a post-1991 82077
> [ 19.373161] loop: module loaded
> [ 19.373234] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
> [ 19.373275] Copyright (c) 1999-2006 Intel Corporation.
> [ 19.373350] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) ->
> IRQ 16
> [ 19.373436] PCI: Setting latency timer of device 0000:02:00.0 to 64
> [ 19.429545] e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width
> x1) 00:1b:21:02:86:95
> [ 19.486899] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
> [ 19.486947] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
> [ 19.486987] e1000e: Copyright (c) 1999-2007 Intel Corporation.
> [ 19.487052] netconsole: local port 4444
> [ 19.487091] netconsole: local IP 192.168.0.1
> [ 19.487129] netconsole: interface eth0
> [ 19.487168] netconsole: remote port 514
> [ 19.487206] netconsole: remote IP 192.168.0.254
> [ 19.487246] netconsole: remote ethernet address 00:19:d1:6e:9d:43
> [ 19.487287] netconsole: device eth0 not up yet, forcing it
> [ 19.793953] Clockevents: could not switch to one-shot mode:<6>Clockevents:
> could not switch to one-shot mode: lapic is not functional.
> [ 19.793956] Could not switch to high resolution mode on CPU 1
> [ 19.794073] lapic is not functional.
> [ 19.794111] Could not switch to high resolution mode on CPU 0
> [ 22.522434] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full
> Duplex, Flow Control: RX/TX
> [ 22.524960] console [netcon0] enabled
> [ 22.537821] netconsole: network logging started
> [ 22.537892] Driver 'sd' needs updating - please use bus_type methods
> [ 22.537954] Driver 'sr' needs updating - please use bus_type methods
> [ 22.538040] ahci 0000:00:1f.2: version 3.0
> [ 22.538052] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) ->
> IRQ 18
> [ 23.537862] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf
> impl SATA mode
> [ 23.537913] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part [
> 23.537956] PCI: Setting latency timer of device 0000:00:1f.2 to 64
> [ 23.538089] scsi0 : ahci
> [ 23.538170] scsi1 : ahci
> [ 23.538240] scsi2 : ahci
> [ 23.538318] scsi3 : ahci
> [ 23.538411] ata1: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe100
> irq 218
> [ 23.538463] ata2: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe180
> irq 218
> [ 23.538518] ata3: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe200
> irq 218
> [ 23.538573] ata4: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe280
> irq 218
> [ 23.993352] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 24.000089] ata1.00: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
> [ 24.000131] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
> [ 24.000956] ata1.00: configured for UDMA/133
> [ 24.455844] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> [ 24.609697] ata2.00: ATAPI: TSSTcorpCD/DVDW SH-S183L, SB02, max UDMA/33,
> ATAPI AN
> [ 24.609746] ata2.00: applying bridge limits
> [ 24.763896] ata2.00: configured for UDMA/33
> [ 25.066174] ata3: SATA link down (SStatus 0 SControl 300)
> [ 25.368842] ata4: SATA link down (SStatus 0 SControl 300)
> [ 25.368947] scsi 0:0:0:0: Direct-Access ATA WDC WD7500AAKS-0 30.0
> PQ: 0 ANSI: 5
> [ 25.369061] sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156
> MB)
> [ 25.369117] sd 0:0:0:0: [sda] Write Protect is off
> [ 25.369162] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 25.369171] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
> doesn't support DPO or FUA
> [ 25.369252] sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156
> MB)
> [ 25.369309] sd 0:0:0:0: [sda] Write Protect is off
> [ 25.369354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 25.369364] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
> doesn't support DPO or FUA
> [ 25.369419] sda: sda1 sda2
> [ 25.374009] sd 0:0:0:0: [sda] Attached SCSI disk
> [ 25.374905] scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB02
> PQ: 0 ANSI: 5
> [ 25.383411] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2
> cdda tray
> [ 25.383462] Uniform CD-ROM driver Revision: 3.20
> [ 25.383558] sr 1:0:0:0: Attached scsi CD-ROM sr0
> [ 25.383615] ata_piix 0000:00:1f.1: version 2.12
> [ 25.383622] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) ->
> IRQ 17
> [ 25.383723] PCI: Setting latency timer of device 0000:00:1f.1 to 64
> [ 25.383756] scsi4 : ata_piix
> [ 25.383834] scsi5 : ata_piix
> [ 25.384178] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfb00 irq
> 14
> [ 25.384220] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfb08 irq
> 15
> [ 25.534721] ata6: port disabled. ignoring.
> [ 25.545781] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 17 (level, low) ->
> IRQ 19
> [ 25.595935] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]
> MMIO=[fd9ff000-fd9ff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
> [ 25.596066] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) ->
> IRQ 20
> [ 25.596153] PCI: Setting latency timer of device 0000:00:1d.7 to 64
> [ 25.596155] ehci_hcd 0000:00:1d.7: EHCI Host Controller
> [ 25.596237] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
> number 1
> [ 25.600172] PCI: cache line size of 32 is not supported by device
> 0000:00:1d.7
> [ 25.600177] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfdfff000
> [ 25.609576] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10
> Dec 2004
> [ 25.609735] usb usb1: configuration #1 chosen from 1 choice
> [ 25.609799] hub 1-0:1.0: USB hub found
> [ 25.609847] hub 1-0:1.0: 8 ports detected
> [ 25.710538] USB Universal Host Controller Interface driver v3.0
> [ 25.710603] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) ->
> IRQ 20
> [ 25.710696] PCI: Setting latency timer of device 0000:00:1d.0 to 64
> [ 25.710698] uhci_hcd 0000:00:1d.0: UHCI Host Controller
> [ 25.710766] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
> number 2
> [ 25.710839] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000ff00
> [ 25.710970] usb usb2: configuration #1 chosen from 1 choice
> [ 25.711034] hub 2-0:1.0: USB hub found
> [ 25.711081] hub 2-0:1.0: 2 ports detected
> [ 25.811418] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) ->
> IRQ 18
> [ 25.811498] PCI: Setting latency timer of device 0000:00:1d.1 to 64
> [ 25.811500] uhci_hcd 0000:00:1d.1: UHCI Host Controller
> [ 25.811567] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
> number 3
> [ 25.811641] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000fe00
> [ 25.811774] usb usb3: configuration #1 chosen from 1 choice
> [ 25.811838] hub 3-0:1.0: USB hub found
> [ 25.811885] hub 3-0:1.0: 2 ports detected
> [ 25.912307] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) ->
> IRQ 17
> [ 25.912394] PCI: Setting latency timer of device 0000:00:1d.2 to 64
> [ 25.912395] uhci_hcd 0000:00:1d.2: UHCI Host Controller
> [ 25.912462] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
> number 4
> [ 25.912542] uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000fd00
> [ 25.912670] usb usb4: configuration #1 chosen from 1 choice
> [ 25.912739] hub 4-0:1.0: USB hub found
> [ 25.912780] hub 4-0:1.0: 2 ports detected
> [ 26.013198] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) ->
> IRQ 16
> [ 26.013284] PCI: Setting latency timer of device 0000:00:1d.3 to 64
> [ 26.013286] uhci_hcd 0000:00:1d.3: UHCI Host Controller
> [ 26.013354] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus
> number 5
> [ 26.013428] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
> [ 26.013562] usb usb5: configuration #1 chosen from 1 choice
> [ 26.013625] hub 5-0:1.0: USB hub found
> [ 26.013672] hub 5-0:1.0: 2 ports detected
> [ 26.114089] Initializing USB Mass Storage driver...
> [ 26.225899] usb 2-2: new low speed USB device using uhci_hcd and address 2
> [ 26.395248] usb 2-2: configuration #1 chosen from 1 choice
> [ 26.603485] usb 3-1: new low speed USB device using uhci_hcd and address 2
> [ 26.766761] usb 3-1: configuration #1 chosen from 1 choice
> [ 26.770797] usbcore: registered new interface driver usb-storage
> [ 26.770839] USB Mass Storage support registered.
> [ 26.770934] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
> [ 26.770976] PNP: PS/2 appears to have AUX port disabled, if this is
> incorrect please boot with i8042.nopnp
> [ 26.771515] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 26.771603] mice: PS/2 mouse device common for all mice
> [ 26.801022] input: AT Translated Set 2 keyboard as
> /devices/platform/i8042/serio0/input/input2
> [ 26.803324] input: PC Speaker as /devices/platform/pcspkr/input/input3
> [ 26.850285] ieee1394: Host added: ID:BUS[0-00:1023]
> GUID[00508d0000994687]
> [ 26.852373] abituguru3: found Abit uGuru3, motherboard ID: 0016 (AW9D-MAX)
> [ 26.852819] coretemp coretemp.0: Using undocumented features, absolute
> temperature might be wrong!
> [ 26.852914] coretemp coretemp.1: Using undocumented features, absolute
> temperature might be wrong!
> [ 26.853014] usbcore: registered new interface driver hiddev
> [ 26.867836] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)
> as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input4
> [ 26.870213] input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse
> with IntelliEye(TM)] on usb-0000:00:1d.0-2
> [ 27.142344] hiddev96: USB HID v1.11 Device [Belkin Belkin UPS] on
> usb-0000:00:1d.1-1
> [ 27.142461] usbcore: registered new interface driver usbhid
> [ 27.142503] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> [ 27.142570] Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue
> Nov 20 19:16:42 2007 UTC).
> [ 27.143593] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) ->
> IRQ 16
> [ 27.143681] PCI: Setting latency timer of device 0000:00:1b.0 to 64
> [ 27.194837] hda_codec: Unknown model for ALC882, trying auto-probe from
> BIOS...
> [ 27.234870] ALSA device list:
> [ 27.234909] #0: HDA Intel at 0xfdff8000 irq 16
> [ 27.234950] TCP cubic registered
> [ 27.235004] NET: Registered protocol family 1
> [ 27.235057] NET: Registered protocol family 17
> [ 27.235187] RPC: Registered udp transport module.
> [ 27.235228] RPC: Registered tcp transport module.
> [ 27.235275] Testing NMI watchdog ... OK.
> [ 27.255332] Starting balanced_irq
> [ 27.255383] Using IPI Shortcut mode
> [ 27.285525] UDF-fs: No VRS found
> [ 27.323228] XFS mounting filesystem sda2
> [ 27.413136] Ending clean XFS mount for filesystem: sda2
> [ 27.413153] VFS: Mounted root (xfs filesystem) readonly.
> [ 27.413273] Freeing unused kernel memory: 224k freed
> [ 29.727530] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) ->
> IRQ 18
> [ 31.260700] Adding 8393920k swap on /dev/sda1. Priority:-1 extents:1
> across:8393920k
> [ 49.957428] nvidia: module license 'NVIDIA' taints kernel.
> [ 50.210535] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) ->
> IRQ 16
> [ 50.210547] PCI: Setting latency timer of device 0000:01:00.0 to 64
> [ 50.210639] NVRM: loading NVIDIA UNIX x86 Kernel Module 171.05 Tue Jan
> 22 18:08:39 PST 2008
On Mon, 10 Mar 2008, Justin Piszcz wrote:
> Running kernel 2.6.24.3 on Debian Testing here..
>
> [ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561
> native_smp_call_function_mask()
> [ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
> [ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
> [ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
> [ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
> [ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
> [ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
> [ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
> [ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
Can you please try the backported patch below.
Thanks,
tglx
------------->
commit e94271017f0933b29362a3c9dea5a6b9d04d98e1
Author: Jan Beulich <[email protected]>
Date: Wed Jan 30 13:31:24 2008 +0100
x86: adjust enable_NMI_through_LVT0()
Its previous use in a call to on_each_cpu() was pointless, as at the
time that code gets executed only one CPU is online. Further, the
function can be __cpuinit, and for this to work without
CONFIG_HOTPLUG_CPU setup_nmi() must also get an attribute (this one
can even be __init; on 64-bits check_timer() also was lacking that
attribute).
Signed-off-by: Jan Beulich <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
[ [email protected]: backport to 2.6.24.3]
---
arch/x86/kernel/apic_32.c | 2 +-
arch/x86/kernel/apic_64.c | 2 +-
arch/x86/kernel/io_apic_32.c | 4 ++--
arch/x86/kernel/io_apic_64.c | 6 +++---
arch/x86/kernel/smpboot_32.c | 2 +-
arch/x86/kernel/smpboot_64.c | 2 +-
include/asm-x86/apic_32.h | 2 +-
include/asm-x86/io_apic_64.h | 2 +-
8 files changed, 11 insertions(+), 11 deletions(-)
Index: linux-2.6/arch/x86/kernel/apic_32.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/apic_32.c
+++ linux-2.6/arch/x86/kernel/apic_32.c
@@ -154,7 +154,7 @@ unsigned long safe_apic_wait_icr_idle(vo
/**
* enable_NMI_through_LVT0 - enable NMI through local vector table 0
*/
-void enable_NMI_through_LVT0 (void * dummy)
+void __cpuinit enable_NMI_through_LVT0(void)
{
unsigned int v = APIC_DM_NMI;
Index: linux-2.6/arch/x86/kernel/apic_64.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/apic_64.c
+++ linux-2.6/arch/x86/kernel/apic_64.c
@@ -151,7 +151,7 @@ unsigned int safe_apic_wait_icr_idle(voi
return send_status;
}
-void enable_NMI_through_LVT0 (void * dummy)
+void enable_NMI_through_LVT0(void)
{
unsigned int v;
Index: linux-2.6/arch/x86/kernel/io_apic_32.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/io_apic_32.c
+++ linux-2.6/arch/x86/kernel/io_apic_32.c
@@ -2080,7 +2080,7 @@ static struct irq_chip lapic_chip __read
.eoi = ack_apic,
};
-static void setup_nmi (void)
+static void __init setup_nmi(void)
{
/*
* Dirty trick to enable the NMI watchdog ...
@@ -2093,7 +2093,7 @@ static void setup_nmi (void)
*/
apic_printk(APIC_VERBOSE, KERN_INFO "activating NMI Watchdog ...");
- on_each_cpu(enable_NMI_through_LVT0, NULL, 1, 1);
+ enable_NMI_through_LVT0();
apic_printk(APIC_VERBOSE, " done.\n");
}
Index: linux-2.6/arch/x86/kernel/io_apic_64.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/io_apic_64.c
+++ linux-2.6/arch/x86/kernel/io_apic_64.c
@@ -1565,7 +1565,7 @@ static struct hw_interrupt_type lapic_ir
.end = end_lapic_irq,
};
-static void setup_nmi (void)
+static void __init setup_nmi(void)
{
/*
* Dirty trick to enable the NMI watchdog ...
@@ -1578,7 +1578,7 @@ static void setup_nmi (void)
*/
printk(KERN_INFO "activating NMI Watchdog ...");
- enable_NMI_through_LVT0(NULL);
+ enable_NMI_through_LVT0();
printk(" done.\n");
}
@@ -1654,7 +1654,7 @@ static inline void unlock_ExtINT_logic(v
*
* FIXME: really need to revamp this for modern platforms only.
*/
-static inline void check_timer(void)
+static inline void __init check_timer(void)
{
struct irq_cfg *cfg = irq_cfg + 0;
int apic1, pin1, apic2, pin2;
Index: linux-2.6/arch/x86/kernel/smpboot_32.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/smpboot_32.c
+++ linux-2.6/arch/x86/kernel/smpboot_32.c
@@ -405,7 +405,7 @@ static void __cpuinit start_secondary(vo
setup_secondary_clock();
if (nmi_watchdog == NMI_IO_APIC) {
disable_8259A_irq(0);
- enable_NMI_through_LVT0(NULL);
+ enable_NMI_through_LVT0();
enable_8259A_irq(0);
}
/*
Index: linux-2.6/arch/x86/kernel/smpboot_64.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/smpboot_64.c
+++ linux-2.6/arch/x86/kernel/smpboot_64.c
@@ -338,7 +338,7 @@ void __cpuinit start_secondary(void)
if (nmi_watchdog == NMI_IO_APIC) {
disable_8259A_irq(0);
- enable_NMI_through_LVT0(NULL);
+ enable_NMI_through_LVT0();
enable_8259A_irq(0);
}
Index: linux-2.6/include/asm-x86/apic_32.h
===================================================================
--- linux-2.6.orig/include/asm-x86/apic_32.h
+++ linux-2.6/include/asm-x86/apic_32.h
@@ -109,7 +109,7 @@ extern void setup_boot_APIC_clock (void)
extern void setup_secondary_APIC_clock (void);
extern int APIC_init_uniprocessor (void);
-extern void enable_NMI_through_LVT0 (void * dummy);
+extern void enable_NMI_through_LVT0(void);
#define ARCH_APICTIMER_STOPS_ON_C3 1
Index: linux-2.6/include/asm-x86/io_apic_64.h
===================================================================
--- linux-2.6.orig/include/asm-x86/io_apic_64.h
+++ linux-2.6/include/asm-x86/io_apic_64.h
@@ -129,7 +129,7 @@ extern int io_apic_set_pci_routing (int
extern int sis_apic_bug; /* dummy */
-void enable_NMI_through_LVT0 (void * dummy);
+void enable_NMI_through_LVT0(void);
extern spinlock_t i8259A_lock;
On Tue, 11 Mar 2008, Thomas Gleixner wrote:
> On Mon, 10 Mar 2008, Justin Piszcz wrote:
>> Running kernel 2.6.24.3 on Debian Testing here..
>>
>> [ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561
>> native_smp_call_function_mask()
>> [ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
>> [ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
>> [ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
>> [ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
>> [ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
>> [ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
>> [ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
>> [ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
>
> Can you please try the backported patch below.
>
> Thanks,
> tglx
>
Patching now and will have the result shortly.
# patch -p1 < ../patch
patching file arch/x86/kernel/apic_32.c
patching file arch/x86/kernel/apic_64.c
patching file arch/x86/kernel/io_apic_32.c
patching file arch/x86/kernel/io_apic_64.c
patching file arch/x86/kernel/smpboot_32.c
patching file arch/x86/kernel/smpboot_64.c
patching file include/asm-x86/apic_32.h
patching file include/asm-x86/io_apic_64.h
#
On Tue, 11 Mar 2008, Justin Piszcz wrote:
>
>
> On Tue, 11 Mar 2008, Thomas Gleixner wrote:
>
>> On Mon, 10 Mar 2008, Justin Piszcz wrote:
>>> Running kernel 2.6.24.3 on Debian Testing here..
>>>
>>> [ 19.141846] WARNING: at arch/x86/kernel/smp_32.c:561
>>> native_smp_call_function_mask()
>>> [ 19.141896] Pid: 1, comm: swapper Not tainted 2.6.24.3 #1
>>> [ 19.141937] [<c010e50b>] native_smp_call_function_mask+0x14b/0x150
>>> [ 19.142009] [<c01036c3>] common_interrupt+0x23/0x28
>>> [ 19.142076] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
>>> [ 19.142144] [<c010f470>] enable_NMI_through_LVT0+0x0/0x30
>>> [ 19.142212] [<c010e8fc>] smp_call_function+0x1c/0x30
>>> [ 19.142279] [<c012196c>] on_each_cpu+0x2c/0x60
>>> [ 19.142346] [<c0110840>] setup_nmi+0x30/0x50
>>
>> Can you please try the backported patch below.
>>
>> Thanks,
>> tglx
>>
>
> Patching now and will have the result shortly.
>
> # patch -p1 < ../patch
> patching file arch/x86/kernel/apic_32.c
> patching file arch/x86/kernel/apic_64.c
> patching file arch/x86/kernel/io_apic_32.c
> patching file arch/x86/kernel/io_apic_64.c
> patching file arch/x86/kernel/smpboot_32.c
> patching file arch/x86/kernel/smpboot_64.c
> patching file include/asm-x86/apic_32.h
> patching file include/asm-x86/io_apic_64.h
> #
>
>
Patched, problem resolved. Thomas, will this patch be included in
2.6.24.4? Thanks!
Dmesg output:
[ 0.000000] Linux version 2.6.24.3 (root@hostname) (gcc version 4.2.3 (Debian 4.2.3-2)) #2 SMP PREEMPT Tue Mar 11 07:53:59 EDT 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfee0000 (usable)
[ 0.000000] BIOS-e820: 00000000cfee0000 - 00000000cfee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cfee3000 - 00000000cfef0000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] Warning only 4GB will be used.
[ 0.000000] Use a HIGHMEM64G enabled kernel.
[ 0.000000] 3200MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f3430
[ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 1048576
[ 0.000000] On node 0 totalpages: 1048576
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 6400 pages used for memmap
[ 0.000000] HighMem zone: 812800 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F7330, 0014 (r0 IntelR)
[ 0.000000] ACPI: RSDT CFEE3040, 0038 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP CFEE30C0, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT CFEE3180, 485D (r1 INTELR AWRDACPI 1000 MSFT 100000E)
[ 0.000000] ACPI: FACS CFEE0000, 0040
[ 0.000000] ACPI: MCFG CFEE7B40, 003C (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: APIC CFEE7A40, 0084 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: SSDT CFEE7BC0, 019E (r1 PmRef Cpu0Ist 3000 INTL 20041203)
[ 0.000000] ACPI: SSDT CFEE8050, 02F1 (r1 PmRef CpuPm 3000 INTL 20041203)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at d0000000 (gap: cff00000:10100000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
[ 0.000000] Kernel command line: auto BOOT_IMAGE=2.6.24.3-2 ro root=802 [email protected]/eth0,[email protected]/00:19:D1:6E:9D:43 nmi_watchdog=1
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2720.540 MHz processor.
[ 18.907116] Console: colour VGA+ 80x25
[ 18.907118] console [tty0] enabled
[ 18.909743] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 18.909970] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 19.047676] Memory: 3367044k/4194304k available (3253k kernel code, 38552k reserved, 1071k data, 224k init, 2489216k highmem)
[ 19.047733] virtual kernel memory layout:
[ 19.047734] fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB)
[ 19.047735] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 19.047735] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 19.047736] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 19.047737] .init : 0xc0540000 - 0xc0578000 ( 224 kB)
[ 19.047737] .data : 0xc042d4a4 - 0xc053930c (1071 kB)
[ 19.047738] .text : 0xc0100000 - 0xc042d4a4 (3253 kB)
[ 19.048048] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 19.048153] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 19.108145] Calibrating delay using timer specific routine.. 5443.07 BogoMIPS (lpj=2721535)
[ 19.108244] Mount-cache hash table entries: 512
[ 19.108375] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[ 19.108380] monitor/mwait feature present.
[ 19.108419] using mwait in idle threads.
[ 19.108459] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 19.108525] CPU: L2 cache: 4096K
[ 19.108564] CPU: Physical Processor ID: 0
[ 19.108602] CPU: Processor Core ID: 0
[ 19.108640] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[ 19.108644] Intel machine check architecture supported.
[ 19.108685] Intel machine check reporting enabled on CPU#0.
[ 19.108726] Compat vDSO mapped to ffffe000.
[ 19.108773] Checking 'hlt' instruction... OK.
[ 19.112431] Freeing SMP alternatives: 13k freed
[ 19.112471] ACPI: Core revision 20070126
[ 19.116541] CPU0: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping 06
[ 19.116648] Booting processor 1/1 eip 2000
[ 19.127530] Initializing CPU#1
[ 19.187046] Calibrating delay using timer specific routine.. 5440.15 BogoMIPS (lpj=2720077)
[ 19.187050] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[ 19.187053] monitor/mwait feature present.
[ 19.187055] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 19.187056] CPU: L2 cache: 4096K
[ 19.187058] CPU: Physical Processor ID: 0
[ 19.187058] CPU: Processor Core ID: 1
[ 19.187059] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[ 19.187062] Intel machine check architecture supported.
[ 19.187064] Intel machine check reporting enabled on CPU#1.
[ 19.187491] CPU1: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping 06
[ 19.187941] Total of 2 processors activated (10883.22 BogoMIPS).
[ 19.188126] ENABLING IO-APIC IRQs
[ 19.188321] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 19.299909] APIC timer registered as dummy, due to nmi_watchdog=1!
[ 19.300012] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 19.320069] Brought up 2 CPUs
[ 19.320215] net_namespace: 64 bytes
[ 19.320460] NET: Registered protocol family 16
[ 19.320580] ACPI: bus type pci registered
[ 19.320625] PCI: Using MMCONFIG
[ 19.321025] Setting up standard PCI resources
[ 19.321730] mtrr: your CPUs had inconsistent variable MTRR settings
[ 19.321771] mtrr: probably your BIOS does not setup all CPUs.
[ 19.321811] mtrr: corrected configuration.
[ 19.322962] ACPI: EC: Look up EC in DSDT
[ 19.325653] ACPI: Interpreter enabled
[ 19.325692] ACPI: (supports S0 S5)
[ 19.325786] ACPI: Using IOAPIC for interrupt routing
[ 19.328901] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 19.329277] Force enabled HPET at base address 0xfed00000
[ 19.329281] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 19.329323] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[ 19.329822] PCI: Transparent bridge - 0000:00:1e.0
[ 19.329880] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 19.329990] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 19.330042] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
[ 19.330094] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 19.330145] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 19.338215] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 9 *10 11 12 14 15)
[ 19.338621] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 *5 7 9 10 11 12 14 15)
[ 19.339036] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 *7 9 10 11 12 14 15)
[ 19.339440] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 9 10 *11 12 14 15)
[ 19.339845] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 19.340317] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 19.340784] ACPI: PCI Interrupt Link [LNK0] (IRQs 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 19.341256] ACPI: PCI Interrupt Link [LNK1] (IRQs *4 5 7 9 10 11 12 14 15)
[ 19.341667] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 19.341723] pnp: PnP ACPI init
[ 19.341765] ACPI: bus type pnp registered
[ 19.343344] pnpacpi: exceeded the max number of mem resources: 12
[ 19.343420] pnp: PnP ACPI: found 13 devices
[ 19.343459] ACPI: ACPI bus type pnp unregistered
[ 19.343597] SCSI subsystem initialized
[ 19.343652] libata version 3.00 loaded.
[ 19.343708] usbcore: registered new interface driver usbfs
[ 19.343779] usbcore: registered new interface driver hub
[ 19.343842] usbcore: registered new device driver usb
[ 19.343976] PCI: Using ACPI for IRQ routing
[ 19.344015] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 19.348007] hpet clockevent registered
[ 19.348010] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 19.348159] hpet0: 3 64-bit timers, 14318180 Hz
[ 19.350007] Time: tsc clocksource has been installed.
[ 19.353024] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 19.353066] system 00:01: ioport range 0x880-0x88f has been reserved
[ 19.353110] system 00:08: ioport range 0x400-0x4bf could not be reserved
[ 19.353154] system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
[ 19.353205] system 00:0c: iomem range 0x636500-0xd1ccff could not be reserved
[ 19.353247] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved
[ 19.353288] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
[ 19.353330] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[ 19.353371] system 00:0c: iomem range 0xcfee0000-0xcfefffff could not be reserved
[ 19.353420] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 19.353462] system 00:0c: iomem range 0x100000-0xcfedffff could not be reserved
[ 19.353511] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 19.354394] system 00:0c: iomem range 0xfed13000-0xfed1dfff could not be reserved
[ 19.354443] system 00:0c: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 19.354492] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 19.354541] system 00:0c: iomem range 0xffb00000-0xffb7ffff could not be reserved
[ 19.384785] PCI: Bridge: 0000:00:01.0
[ 19.384823] IO window: b000-bfff
[ 19.384862] MEM window: f8000000-fbffffff
[ 19.384901] PREFETCH window: d0000000-dfffffff
[ 19.384940] PCI: Bridge: 0000:00:1c.0
[ 19.384984] IO window: a000-afff
[ 19.385023] MEM window: fda00000-fdafffff
[ 19.385063] PREFETCH window: fd700000-fd7fffff
[ 19.385103] PCI: Bridge: 0000:00:1c.2
[ 19.385141] IO window: e000-efff
[ 19.385181] MEM window: fde00000-fdefffff
[ 19.385220] PREFETCH window: fdd00000-fddfffff
[ 19.385260] PCI: Bridge: 0000:00:1c.4
[ 19.385299] IO window: d000-dfff
[ 19.385338] MEM window: fdc00000-fdcfffff
[ 19.385377] PREFETCH window: fdb00000-fdbfffff
[ 19.385418] PCI: Bridge: 0000:00:1e.0
[ 19.385456] IO window: c000-cfff
[ 19.385496] MEM window: fd900000-fd9fffff
[ 19.385535] PREFETCH window: fd800000-fd8fffff
[ 19.385579] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.385656] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.385666] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.385743] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 19.385753] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 17
[ 19.385830] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 19.385839] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.385917] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 19.385922] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 19.385928] NET: Registered protocol family 2
[ 19.394986] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 19.395148] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 19.395493] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 19.395743] TCP: Hash tables configured (established 131072 bind 65536)
[ 19.395784] TCP reno registered
[ 19.399482] highmem bounce pool size: 64 pages
[ 19.400983] Installing knfsd (copyright (C) 1996 [email protected]).
[ 19.401153] SGI XFS with no debug enabled
[ 19.401536] io scheduler noop registered
[ 19.401611] io scheduler cfq registered (default)
[ 19.401712] Boot video device is 0000:01:00.0
[ 19.401766] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.401777] assign_interrupt_mode Found MSI capability
[ 19.401826] Allocate Port Service[0000:00:01.0:pcie00]
[ 19.401845] Allocate Port Service[0000:00:01.0:pcie03]
[ 19.401879] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 19.401902] assign_interrupt_mode Found MSI capability
[ 19.401963] Allocate Port Service[0000:00:1c.0:pcie00]
[ 19.401989] Allocate Port Service[0000:00:1c.0:pcie02]
[ 19.402007] Allocate Port Service[0000:00:1c.0:pcie03]
[ 19.402051] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 19.402074] assign_interrupt_mode Found MSI capability
[ 19.402130] Allocate Port Service[0000:00:1c.2:pcie00]
[ 19.402148] Allocate Port Service[0000:00:1c.2:pcie02]
[ 19.402167] Allocate Port Service[0000:00:1c.2:pcie03]
[ 19.402212] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 19.402235] assign_interrupt_mode Found MSI capability
[ 19.402291] Allocate Port Service[0000:00:1c.4:pcie00]
[ 19.402309] Allocate Port Service[0000:00:1c.4:pcie02]
[ 19.402327] Allocate Port Service[0000:00:1c.4:pcie03]
[ 19.402454] input: Power Button (FF) as /devices/virtual/input/input0
[ 19.402495] ACPI: Power Button (FF) [PWRF]
[ 19.402572] input: Power Button (CM) as /devices/virtual/input/input1
[ 19.402613] ACPI: Power Button (CM) [PWRB]
[ 19.412000] Real Time Clock Driver v1.12ac
[ 19.412085] Linux agpgart interface v0.102
[ 19.412170] Floppy drive(s): fd0 is 1.44M
[ 19.426565] FDC 0 is a post-1991 82077
[ 19.427669] loop: module loaded
[ 19.427743] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 19.427784] Copyright (c) 1999-2006 Intel Corporation.
[ 19.427859] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.427945] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 19.484025] e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:1b:21:02:86:95
[ 19.541401] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 19.541449] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
[ 19.541489] e1000e: Copyright (c) 1999-2007 Intel Corporation.
[ 19.541554] netconsole: local port 4444
[ 19.541593] netconsole: local IP 192.168.0.1
[ 19.541631] netconsole: interface eth0
[ 19.541669] netconsole: remote port 514
[ 19.541708] netconsole: remote IP 192.168.0.254
[ 19.541747] netconsole: remote ethernet address 00:19:d1:6e:9d:43
[ 19.541788] netconsole: device eth0 not up yet, forcing it
[ 19.848460] Clockevents: could not switch to one-shot mode:<6>Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 19.848464] Could not switch to high resolution mode on CPU 1
[ 19.848580] lapic is not functional.
[ 19.848618] Could not switch to high resolution mode on CPU 0
[ 22.620889] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 22.623419] console [netcon0] enabled
[ 22.634382] netconsole: network logging started
[ 22.634443] Driver 'sd' needs updating - please use bus_type methods
[ 22.634505] Driver 'sr' needs updating - please use bus_type methods
[ 22.634581] ahci 0000:00:1f.2: version 3.0
[ 22.634593] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
[ 23.634323] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 23.634374] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 23.635250] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 23.635385] scsi0 : ahci
[ 23.635466] scsi1 : ahci
[ 23.635535] scsi2 : ahci
[ 23.635615] scsi3 : ahci
[ 23.635707] ata1: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe100 irq 218
[ 23.635760] ata2: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe180 irq 218
[ 23.635815] ata3: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe200 irq 218
[ 23.635870] ata4: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe280 irq 218
[ 24.090812] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 24.101764] ata1.00: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
[ 24.101811] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 24.102638] ata1.00: configured for UDMA/133
[ 24.557299] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 24.711312] ata2.00: ATAPI: TSSTcorpCD/DVDW SH-S183L, SB02, max UDMA/33, ATAPI AN
[ 24.711362] ata2.00: applying bridge limits
[ 24.864961] ata2.00: configured for UDMA/33
[ 25.167629] ata3: SATA link down (SStatus 0 SControl 300)
[ 25.470297] ata4: SATA link down (SStatus 0 SControl 300)
[ 25.470401] scsi 0:0:0:0: Direct-Access ATA WDC WD7500AAKS-0 30.0 PQ: 0 ANSI: 5
[ 25.470516] sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
[ 25.470574] sd 0:0:0:0: [sda] Write Protect is off
[ 25.470614] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.470624] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.470705] sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
[ 25.470763] sd 0:0:0:0: [sda] Write Protect is off
[ 25.470803] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.470812] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.470868] sda: sda1 sda2
[ 25.475679] sd 0:0:0:0: [sda] Attached SCSI disk
[ 25.476520] scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB02 PQ: 0 ANSI: 5
[ 25.484713] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 25.484764] Uniform CD-ROM driver Revision: 3.20
[ 25.484854] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 25.484911] ata_piix 0000:00:1f.1: version 2.12
[ 25.484918] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
[ 25.485018] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 25.485050] scsi4 : ata_piix
[ 25.485123] scsi5 : ata_piix
[ 25.485474] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfb00 irq 14
[ 25.485517] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfb08 irq 15
[ 25.636176] ata6: port disabled. ignoring.
[ 25.647236] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 17 (level, low) -> IRQ 19
[ 25.697389] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[fd9ff000-fd9ff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 25.697520] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[ 25.697601] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 25.697603] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 25.697685] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 25.701621] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 25.701626] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfdfff000
[ 25.711031] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.711188] usb usb1: configuration #1 chosen from 1 choice
[ 25.711251] hub 1-0:1.0: USB hub found
[ 25.711299] hub 1-0:1.0: 8 ports detected
[ 25.811993] USB Universal Host Controller Interface driver v3.0
[ 25.812065] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
[ 25.812145] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 25.812147] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 25.812221] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 25.812287] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000ff00
[ 25.812423] usb usb2: configuration #1 chosen from 1 choice
[ 25.812486] hub 2-0:1.0: USB hub found
[ 25.812534] hub 2-0:1.0: 2 ports detected
[ 25.912874] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
[ 25.912960] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 25.912962] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 25.913028] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 25.913102] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000fe00
[ 25.913234] usb usb3: configuration #1 chosen from 1 choice
[ 25.913297] hub 3-0:1.0: USB hub found
[ 25.913344] hub 3-0:1.0: 2 ports detected
[ 26.013762] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
[ 26.013848] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 26.013850] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 26.013923] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 26.013990] uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000fd00
[ 26.014124] usb usb4: configuration #1 chosen from 1 choice
[ 26.014187] hub 4-0:1.0: USB hub found
[ 26.014234] hub 4-0:1.0: 2 ports detected
[ 26.114653] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 26.114733] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 26.114735] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 26.114805] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 26.114873] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[ 26.115006] usb usb5: configuration #1 chosen from 1 choice
[ 26.115069] hub 5-0:1.0: USB hub found
[ 26.115116] hub 5-0:1.0: 2 ports detected
[ 26.215544] Initializing USB Mass Storage driver...
[ 26.327355] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 26.496696] usb 2-2: configuration #1 chosen from 1 choice
[ 26.704941] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 26.868222] usb 3-1: configuration #1 chosen from 1 choice
[ 26.871262] usbcore: registered new interface driver usb-storage
[ 26.871304] USB Mass Storage support registered.
[ 26.871399] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 26.871440] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 26.871986] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 26.872070] mice: PS/2 mouse device common for all mice
[ 26.901335] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 26.903780] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 26.951745] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00508d0000994687]
[ 26.954467] abituguru3: found Abit uGuru3, motherboard ID: 0016 (AW9D-MAX)
[ 26.954914] coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
[ 26.955009] coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
[ 26.955105] usbcore: registered new interface driver hiddev
[ 26.970285] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input4
[ 26.973665] input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-2
[ 27.245803] hiddev96: USB HID v1.11 Device [Belkin Belkin UPS] on usb-0000:00:1d.1-1
[ 27.245923] usbcore: registered new interface driver usbhid
[ 27.245970] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 27.246044] Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC).
[ 27.246223] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 27.246313] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 27.297291] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 27.337324] ALSA device list:
[ 27.337363] #0: HDA Intel at 0xfdff8000 irq 16
[ 27.337412] TCP cubic registered
[ 27.337466] NET: Registered protocol family 1
[ 27.337519] NET: Registered protocol family 17
[ 27.337646] RPC: Registered udp transport module.
[ 27.337686] RPC: Registered tcp transport module.
[ 27.337726] Testing NMI watchdog ... OK.
[ 27.357790] Starting balanced_irq
[ 27.357841] Using IPI Shortcut mode
[ 27.387094] UDF-fs: No VRS found
[ 27.424901] XFS mounting filesystem sda2
[ 27.514808] Ending clean XFS mount for filesystem: sda2
[ 27.514824] VFS: Mounted root (xfs filesystem) readonly.
[ 27.514945] Freeing unused kernel memory: 224k freed
[ 30.284544] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 18
[ 31.387267] Adding 8393920k swap on /dev/sda1. Priority:-1 extents:1 across:8393920k
[ 46.280624] warning: process `nvidia-installe' used the deprecated sysctl system call with 1.23.
[ 46.280777] warning: process `nvidia-installe' used the deprecated sysctl system call with 1.23.
[ 46.323310] nvidia: module license 'NVIDIA' taints kernel.
[ 46.577240] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 46.577247] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 46.577313] NVRM: loading NVIDIA UNIX x86 Kernel Module 171.05 Tue Jan 22 18:08:39 PST 2008
[ 46.597356] warning: process `nvidia-installe' used the deprecated sysctl system call with 1.23.
[ 101.219512] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 101.219618] NVRM: loading NVIDIA UNIX x86 Kernel Module 171.05 Tue Jan 22 18:08:39 PST 2008
This is a note to let you know that we have just queued up the patch titled
Subject: x86: adjust enable_NMI_through_LVT0()
to the 2.6.24-stable tree. Its filename is
x86-adjust-enable_nmi_through_lvt0.patch
A git repo of this tree can be found at
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
>From [email protected] Tue Mar 11 11:09:24 2008
Date: Tue, 11 Mar 2008 11:30:25 +0100 (CET)
From: Thomas Gleixner <[email protected]>
To: Justin Piszcz <[email protected]>
Message-ID: <[email protected]>
Cc: LKML <[email protected]>, Stable Team <[email protected]>
Subject: x86: adjust enable_NMI_through_LVT0()
commit e94271017f0933b29362a3c9dea5a6b9d04d98e1
From: Jan Beulich <[email protected]>
Date: Wed Jan 30 13:31:24 2008 +0100
Its previous use in a call to on_each_cpu() was pointless, as at the
time that code gets executed only one CPU is online. Further, the
function can be __cpuinit, and for this to work without
CONFIG_HOTPLUG_CPU setup_nmi() must also get an attribute (this one
can even be __init; on 64-bits check_timer() also was lacking that
attribute).
Signed-off-by: Jan Beulich <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
[ [email protected]: backport to 2.6.24.3]
Cc: Justin Piszcz <[email protected]>
Signed-off-by: Chris Wright <[email protected]>
---
arch/x86/kernel/apic_32.c | 2 +-
arch/x86/kernel/apic_64.c | 2 +-
arch/x86/kernel/io_apic_32.c | 4 ++--
arch/x86/kernel/io_apic_64.c | 6 +++---
arch/x86/kernel/smpboot_32.c | 2 +-
arch/x86/kernel/smpboot_64.c | 2 +-
include/asm-x86/apic_32.h | 2 +-
include/asm-x86/io_apic_64.h | 2 +-
8 files changed, 11 insertions(+), 11 deletions(-)
--- a/arch/x86/kernel/apic_32.c
+++ b/arch/x86/kernel/apic_32.c
@@ -154,7 +154,7 @@ unsigned long safe_apic_wait_icr_idle(vo
/**
* enable_NMI_through_LVT0 - enable NMI through local vector table 0
*/
-void enable_NMI_through_LVT0 (void * dummy)
+void __cpuinit enable_NMI_through_LVT0(void)
{
unsigned int v = APIC_DM_NMI;
--- a/arch/x86/kernel/apic_64.c
+++ b/arch/x86/kernel/apic_64.c
@@ -151,7 +151,7 @@ unsigned int safe_apic_wait_icr_idle(voi
return send_status;
}
-void enable_NMI_through_LVT0 (void * dummy)
+void enable_NMI_through_LVT0(void)
{
unsigned int v;
--- a/arch/x86/kernel/io_apic_32.c
+++ b/arch/x86/kernel/io_apic_32.c
@@ -2080,7 +2080,7 @@ static struct irq_chip lapic_chip __read
.eoi = ack_apic,
};
-static void setup_nmi (void)
+static void __init setup_nmi(void)
{
/*
* Dirty trick to enable the NMI watchdog ...
@@ -2093,7 +2093,7 @@ static void setup_nmi (void)
*/
apic_printk(APIC_VERBOSE, KERN_INFO "activating NMI Watchdog ...");
- on_each_cpu(enable_NMI_through_LVT0, NULL, 1, 1);
+ enable_NMI_through_LVT0();
apic_printk(APIC_VERBOSE, " done.\n");
}
--- a/arch/x86/kernel/io_apic_64.c
+++ b/arch/x86/kernel/io_apic_64.c
@@ -1565,7 +1565,7 @@ static struct hw_interrupt_type lapic_ir
.end = end_lapic_irq,
};
-static void setup_nmi (void)
+static void __init setup_nmi(void)
{
/*
* Dirty trick to enable the NMI watchdog ...
@@ -1578,7 +1578,7 @@ static void setup_nmi (void)
*/
printk(KERN_INFO "activating NMI Watchdog ...");
- enable_NMI_through_LVT0(NULL);
+ enable_NMI_through_LVT0();
printk(" done.\n");
}
@@ -1654,7 +1654,7 @@ static inline void unlock_ExtINT_logic(v
*
* FIXME: really need to revamp this for modern platforms only.
*/
-static inline void check_timer(void)
+static inline void __init check_timer(void)
{
struct irq_cfg *cfg = irq_cfg + 0;
int apic1, pin1, apic2, pin2;
--- a/arch/x86/kernel/smpboot_32.c
+++ b/arch/x86/kernel/smpboot_32.c
@@ -405,7 +405,7 @@ static void __cpuinit start_secondary(vo
setup_secondary_clock();
if (nmi_watchdog == NMI_IO_APIC) {
disable_8259A_irq(0);
- enable_NMI_through_LVT0(NULL);
+ enable_NMI_through_LVT0();
enable_8259A_irq(0);
}
/*
--- a/arch/x86/kernel/smpboot_64.c
+++ b/arch/x86/kernel/smpboot_64.c
@@ -338,7 +338,7 @@ void __cpuinit start_secondary(void)
if (nmi_watchdog == NMI_IO_APIC) {
disable_8259A_irq(0);
- enable_NMI_through_LVT0(NULL);
+ enable_NMI_through_LVT0();
enable_8259A_irq(0);
}
--- a/include/asm-x86/apic_32.h
+++ b/include/asm-x86/apic_32.h
@@ -109,7 +109,7 @@ extern void setup_boot_APIC_clock (void)
extern void setup_secondary_APIC_clock (void);
extern int APIC_init_uniprocessor (void);
-extern void enable_NMI_through_LVT0 (void * dummy);
+extern void enable_NMI_through_LVT0(void);
#define ARCH_APICTIMER_STOPS_ON_C3 1
--- a/include/asm-x86/io_apic_64.h
+++ b/include/asm-x86/io_apic_64.h
@@ -129,7 +129,7 @@ extern int io_apic_set_pci_routing (int
extern int sis_apic_bug; /* dummy */
-void enable_NMI_through_LVT0 (void * dummy);
+void enable_NMI_through_LVT0(void);
extern spinlock_t i8259A_lock;
Patches currently in stable-queue which might be from [email protected] are
queue-2.6.24/x86-adjust-enable_nmi_through_lvt0.patch