Atomic transfers are required to properly power off a machine through
an I2C controlled PMIC, such as the Actions Semi ATC260x series.
System shutdown may happen with interrupts being disabled and, as a
consequence, the kernel may hang if the driver does not support atomic
transfers.
This functionality is essentially implemented by polling the FIFO
Status register until either Command Execute Completed or NACK Error
bits are set.
Signed-off-by: Cristian Ciocaltea <[email protected]>
---
drivers/i2c/busses/i2c-owl.c | 80 ++++++++++++++++++++++++++----------
1 file changed, 59 insertions(+), 21 deletions(-)
diff --git a/drivers/i2c/busses/i2c-owl.c b/drivers/i2c/busses/i2c-owl.c
index 672f1f239bd6..90dd2e814313 100644
--- a/drivers/i2c/busses/i2c-owl.c
+++ b/drivers/i2c/busses/i2c-owl.c
@@ -14,6 +14,7 @@
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of_device.h>
@@ -76,6 +77,7 @@
#define OWL_I2C_FIFOCTL_TFR BIT(2)
/* I2Cc_FIFOSTAT Bit Mask */
+#define OWL_I2C_FIFOSTAT_CECB BIT(0)
#define OWL_I2C_FIFOSTAT_RNB BIT(1)
#define OWL_I2C_FIFOSTAT_RFE BIT(2)
#define OWL_I2C_FIFOSTAT_TFF BIT(5)
@@ -83,7 +85,8 @@
#define OWL_I2C_FIFOSTAT_RFD GENMASK(15, 8)
/* I2C bus timeout */
-#define OWL_I2C_TIMEOUT msecs_to_jiffies(4 * 1000)
+#define OWL_I2C_TIMEOUT_MS (4 * 1000)
+#define OWL_I2C_TIMEOUT msecs_to_jiffies(OWL_I2C_TIMEOUT_MS)
#define OWL_I2C_MAX_RETRIES 50
@@ -161,29 +164,25 @@ static void owl_i2c_set_freq(struct owl_i2c_dev *i2c_dev)
writel(OWL_I2C_DIV_FACTOR(val), i2c_dev->base + OWL_I2C_REG_CLKDIV);
}
-static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
+static int owl_i2c_xfer_data(struct owl_i2c_dev *i2c_dev)
{
- struct owl_i2c_dev *i2c_dev = _dev;
struct i2c_msg *msg = i2c_dev->msg;
- unsigned long flags;
unsigned int stat, fifostat;
- spin_lock_irqsave(&i2c_dev->lock, flags);
-
i2c_dev->err = 0;
/* Handle NACK from slave */
fifostat = readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT);
if (fifostat & OWL_I2C_FIFOSTAT_RNB) {
i2c_dev->err = -ENXIO;
- goto stop;
+ return 1;
}
/* Handle bus error */
stat = readl(i2c_dev->base + OWL_I2C_REG_STAT);
if (stat & OWL_I2C_STAT_BEB) {
i2c_dev->err = -EIO;
- goto stop;
+ return 1;
}
/* Handle FIFO read */
@@ -196,18 +195,30 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
} else {
/* Handle the remaining bytes which were not sent */
while (!(readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) &
- OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
+ OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
writel(msg->buf[i2c_dev->msg_ptr++],
i2c_dev->base + OWL_I2C_REG_TXDAT);
}
}
-stop:
+ return 0;
+}
+
+static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
+{
+ struct owl_i2c_dev *i2c_dev = _dev;
+ unsigned long flags;
+
+ spin_lock_irqsave(&i2c_dev->lock, flags);
+
+ owl_i2c_xfer_data(i2c_dev);
+
/* Clear pending interrupts */
owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT,
OWL_I2C_STAT_IRQP, true);
complete_all(&i2c_dev->msg_complete);
+
spin_unlock_irqrestore(&i2c_dev->lock, flags);
return IRQ_HANDLED;
@@ -235,8 +246,8 @@ static int owl_i2c_check_bus_busy(struct i2c_adapter *adap)
return 0;
}
-static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
- int num)
+static int owl_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg *msgs,
+ int num, bool atomic)
{
struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
struct i2c_msg *msg;
@@ -280,11 +291,12 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
goto err_exit;
}
- reinit_completion(&i2c_dev->msg_complete);
+ if (!atomic)
+ reinit_completion(&i2c_dev->msg_complete);
- /* Enable I2C controller interrupt */
+ /* Enable/disable I2C controller interrupt */
owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
- OWL_I2C_CTL_IRQE, true);
+ OWL_I2C_CTL_IRQE, !atomic);
/*
* Select: FIFO enable, Master mode, Stop enable, Data count enable,
@@ -352,20 +364,33 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
spin_unlock_irqrestore(&i2c_dev->lock, flags);
- time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
- adap->timeout);
+ if (atomic) {
+ /* Wait for Command Execute Completed or NACK Error bits */
+ ret = readl_poll_timeout_atomic(i2c_dev->base + OWL_I2C_REG_FIFOSTAT,
+ val, val & (OWL_I2C_FIFOSTAT_CECB |
+ OWL_I2C_FIFOSTAT_RNB),
+ 10, OWL_I2C_TIMEOUT_MS * 1000);
+ } else {
+ time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
+ adap->timeout);
+ if (!time_left)
+ ret = -ETIMEDOUT;
+ }
spin_lock_irqsave(&i2c_dev->lock, flags);
- if (time_left == 0) {
+
+ if (ret) {
dev_err(&adap->dev, "Transaction timed out\n");
/* Send stop condition and release the bus */
owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
OWL_I2C_CTL_GBCC_STOP | OWL_I2C_CTL_RB,
true);
- ret = -ETIMEDOUT;
goto err_exit;
}
+ if (atomic)
+ owl_i2c_xfer_data(i2c_dev);
+
ret = i2c_dev->err < 0 ? i2c_dev->err : num;
err_exit:
@@ -379,9 +404,22 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
return ret;
}
+static int owl_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
+ int num)
+{
+ return owl_i2c_xfer_common(adap, msgs, num, false);
+}
+
+static int owl_i2c_xfer_atomic(struct i2c_adapter *adap,
+ struct i2c_msg *msgs, int num)
+{
+ return owl_i2c_xfer_common(adap, msgs, num, true);
+}
+
static const struct i2c_algorithm owl_i2c_algorithm = {
- .master_xfer = owl_i2c_master_xfer,
- .functionality = owl_i2c_func,
+ .master_xfer = owl_i2c_xfer,
+ .master_xfer_atomic = owl_i2c_xfer_atomic,
+ .functionality = owl_i2c_func,
};
static const struct i2c_adapter_quirks owl_i2c_quirks = {
--
2.28.0
On 0803, Cristian Ciocaltea wrote:
> Atomic transfers are required to properly power off a machine through
> an I2C controlled PMIC, such as the Actions Semi ATC260x series.
>
> System shutdown may happen with interrupts being disabled and, as a
> consequence, the kernel may hang if the driver does not support atomic
> transfers.
>
> This functionality is essentially implemented by polling the FIFO
> Status register until either Command Execute Completed or NACK Error
> bits are set.
>
> Signed-off-by: Cristian Ciocaltea <[email protected]>
> ---
> drivers/i2c/busses/i2c-owl.c | 80 ++++++++++++++++++++++++++----------
> 1 file changed, 59 insertions(+), 21 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-owl.c b/drivers/i2c/busses/i2c-owl.c
> index 672f1f239bd6..90dd2e814313 100644
> --- a/drivers/i2c/busses/i2c-owl.c
> +++ b/drivers/i2c/busses/i2c-owl.c
> @@ -14,6 +14,7 @@
> #include <linux/i2c.h>
> #include <linux/interrupt.h>
> #include <linux/io.h>
> +#include <linux/iopoll.h>
> #include <linux/module.h>
> #include <linux/of_device.h>
>
> @@ -76,6 +77,7 @@
> #define OWL_I2C_FIFOCTL_TFR BIT(2)
>
> /* I2Cc_FIFOSTAT Bit Mask */
> +#define OWL_I2C_FIFOSTAT_CECB BIT(0)
> #define OWL_I2C_FIFOSTAT_RNB BIT(1)
> #define OWL_I2C_FIFOSTAT_RFE BIT(2)
> #define OWL_I2C_FIFOSTAT_TFF BIT(5)
> @@ -83,7 +85,8 @@
> #define OWL_I2C_FIFOSTAT_RFD GENMASK(15, 8)
>
> /* I2C bus timeout */
> -#define OWL_I2C_TIMEOUT msecs_to_jiffies(4 * 1000)
> +#define OWL_I2C_TIMEOUT_MS (4 * 1000)
> +#define OWL_I2C_TIMEOUT msecs_to_jiffies(OWL_I2C_TIMEOUT_MS)
>
> #define OWL_I2C_MAX_RETRIES 50
>
> @@ -161,29 +164,25 @@ static void owl_i2c_set_freq(struct owl_i2c_dev *i2c_dev)
> writel(OWL_I2C_DIV_FACTOR(val), i2c_dev->base + OWL_I2C_REG_CLKDIV);
> }
>
> -static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> +static int owl_i2c_xfer_data(struct owl_i2c_dev *i2c_dev)
> {
> - struct owl_i2c_dev *i2c_dev = _dev;
> struct i2c_msg *msg = i2c_dev->msg;
> - unsigned long flags;
> unsigned int stat, fifostat;
>
> - spin_lock_irqsave(&i2c_dev->lock, flags);
> -
> i2c_dev->err = 0;
>
> /* Handle NACK from slave */
> fifostat = readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT);
> if (fifostat & OWL_I2C_FIFOSTAT_RNB) {
> i2c_dev->err = -ENXIO;
> - goto stop;
> + return 1;
This looks odd! And moreover you're not making use of this return value
anywhere.
Thanks,
Mani
> }
>
> /* Handle bus error */
> stat = readl(i2c_dev->base + OWL_I2C_REG_STAT);
> if (stat & OWL_I2C_STAT_BEB) {
> i2c_dev->err = -EIO;
> - goto stop;
> + return 1;
> }
>
> /* Handle FIFO read */
> @@ -196,18 +195,30 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> } else {
> /* Handle the remaining bytes which were not sent */
> while (!(readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) &
> - OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
> + OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
> writel(msg->buf[i2c_dev->msg_ptr++],
> i2c_dev->base + OWL_I2C_REG_TXDAT);
> }
> }
>
> -stop:
> + return 0;
> +}
> +
> +static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> +{
> + struct owl_i2c_dev *i2c_dev = _dev;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&i2c_dev->lock, flags);
> +
> + owl_i2c_xfer_data(i2c_dev);
> +
> /* Clear pending interrupts */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT,
> OWL_I2C_STAT_IRQP, true);
>
> complete_all(&i2c_dev->msg_complete);
> +
> spin_unlock_irqrestore(&i2c_dev->lock, flags);
>
> return IRQ_HANDLED;
> @@ -235,8 +246,8 @@ static int owl_i2c_check_bus_busy(struct i2c_adapter *adap)
> return 0;
> }
>
> -static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> - int num)
> +static int owl_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg *msgs,
> + int num, bool atomic)
> {
> struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
> struct i2c_msg *msg;
> @@ -280,11 +291,12 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> goto err_exit;
> }
>
> - reinit_completion(&i2c_dev->msg_complete);
> + if (!atomic)
> + reinit_completion(&i2c_dev->msg_complete);
>
> - /* Enable I2C controller interrupt */
> + /* Enable/disable I2C controller interrupt */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
> - OWL_I2C_CTL_IRQE, true);
> + OWL_I2C_CTL_IRQE, !atomic);
>
> /*
> * Select: FIFO enable, Master mode, Stop enable, Data count enable,
> @@ -352,20 +364,33 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
>
> spin_unlock_irqrestore(&i2c_dev->lock, flags);
>
> - time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
> - adap->timeout);
> + if (atomic) {
> + /* Wait for Command Execute Completed or NACK Error bits */
> + ret = readl_poll_timeout_atomic(i2c_dev->base + OWL_I2C_REG_FIFOSTAT,
> + val, val & (OWL_I2C_FIFOSTAT_CECB |
> + OWL_I2C_FIFOSTAT_RNB),
> + 10, OWL_I2C_TIMEOUT_MS * 1000);
> + } else {
> + time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
> + adap->timeout);
> + if (!time_left)
> + ret = -ETIMEDOUT;
> + }
>
> spin_lock_irqsave(&i2c_dev->lock, flags);
> - if (time_left == 0) {
> +
> + if (ret) {
> dev_err(&adap->dev, "Transaction timed out\n");
> /* Send stop condition and release the bus */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
> OWL_I2C_CTL_GBCC_STOP | OWL_I2C_CTL_RB,
> true);
> - ret = -ETIMEDOUT;
> goto err_exit;
> }
>
> + if (atomic)
> + owl_i2c_xfer_data(i2c_dev);
> +
> ret = i2c_dev->err < 0 ? i2c_dev->err : num;
>
> err_exit:
> @@ -379,9 +404,22 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> return ret;
> }
>
> +static int owl_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> + int num)
> +{
> + return owl_i2c_xfer_common(adap, msgs, num, false);
> +}
> +
> +static int owl_i2c_xfer_atomic(struct i2c_adapter *adap,
> + struct i2c_msg *msgs, int num)
> +{
> + return owl_i2c_xfer_common(adap, msgs, num, true);
> +}
> +
> static const struct i2c_algorithm owl_i2c_algorithm = {
> - .master_xfer = owl_i2c_master_xfer,
> - .functionality = owl_i2c_func,
> + .master_xfer = owl_i2c_xfer,
> + .master_xfer_atomic = owl_i2c_xfer_atomic,
> + .functionality = owl_i2c_func,
> };
>
> static const struct i2c_adapter_quirks owl_i2c_quirks = {
> --
> 2.28.0
>
Hi Mani,
Thanks for the review!
On Fri, Aug 28, 2020 at 06:34:04PM +0530, Manivannan Sadhasivam wrote:
> On 0803, Cristian Ciocaltea wrote:
> > Atomic transfers are required to properly power off a machine through
> > an I2C controlled PMIC, such as the Actions Semi ATC260x series.
> >
> > System shutdown may happen with interrupts being disabled and, as a
> > consequence, the kernel may hang if the driver does not support atomic
> > transfers.
> >
> > This functionality is essentially implemented by polling the FIFO
> > Status register until either Command Execute Completed or NACK Error
> > bits are set.
> >
> > Signed-off-by: Cristian Ciocaltea <[email protected]>
> > ---
> > drivers/i2c/busses/i2c-owl.c | 80 ++++++++++++++++++++++++++----------
> > 1 file changed, 59 insertions(+), 21 deletions(-)
> >
> > diff --git a/drivers/i2c/busses/i2c-owl.c b/drivers/i2c/busses/i2c-owl.c
> > index 672f1f239bd6..90dd2e814313 100644
> > --- a/drivers/i2c/busses/i2c-owl.c
> > +++ b/drivers/i2c/busses/i2c-owl.c
> > @@ -14,6 +14,7 @@
> > #include <linux/i2c.h>
> > #include <linux/interrupt.h>
> > #include <linux/io.h>
> > +#include <linux/iopoll.h>
> > #include <linux/module.h>
> > #include <linux/of_device.h>
> >
> > @@ -76,6 +77,7 @@
> > #define OWL_I2C_FIFOCTL_TFR BIT(2)
> >
> > /* I2Cc_FIFOSTAT Bit Mask */
> > +#define OWL_I2C_FIFOSTAT_CECB BIT(0)
> > #define OWL_I2C_FIFOSTAT_RNB BIT(1)
> > #define OWL_I2C_FIFOSTAT_RFE BIT(2)
> > #define OWL_I2C_FIFOSTAT_TFF BIT(5)
> > @@ -83,7 +85,8 @@
> > #define OWL_I2C_FIFOSTAT_RFD GENMASK(15, 8)
> >
> > /* I2C bus timeout */
> > -#define OWL_I2C_TIMEOUT msecs_to_jiffies(4 * 1000)
> > +#define OWL_I2C_TIMEOUT_MS (4 * 1000)
> > +#define OWL_I2C_TIMEOUT msecs_to_jiffies(OWL_I2C_TIMEOUT_MS)
> >
> > #define OWL_I2C_MAX_RETRIES 50
> >
> > @@ -161,29 +164,25 @@ static void owl_i2c_set_freq(struct owl_i2c_dev *i2c_dev)
> > writel(OWL_I2C_DIV_FACTOR(val), i2c_dev->base + OWL_I2C_REG_CLKDIV);
> > }
> >
> > -static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> > +static int owl_i2c_xfer_data(struct owl_i2c_dev *i2c_dev)
> > {
> > - struct owl_i2c_dev *i2c_dev = _dev;
> > struct i2c_msg *msg = i2c_dev->msg;
> > - unsigned long flags;
> > unsigned int stat, fifostat;
> >
> > - spin_lock_irqsave(&i2c_dev->lock, flags);
> > -
> > i2c_dev->err = 0;
> >
> > /* Handle NACK from slave */
> > fifostat = readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT);
> > if (fifostat & OWL_I2C_FIFOSTAT_RNB) {
> > i2c_dev->err = -ENXIO;
> > - goto stop;
> > + return 1;
>
> This looks odd! And moreover you're not making use of this return value
> anywhere.
You are right, that's just a leftover from my initial implementation
and I totally missed it when I did the final cleanup. Thanks for
spotting it!
> Thanks,
> Mani
If there is nothing else, I can submit the revised patch.
Regards,
Cristi
> > }
> >
> > /* Handle bus error */
> > stat = readl(i2c_dev->base + OWL_I2C_REG_STAT);
> > if (stat & OWL_I2C_STAT_BEB) {
> > i2c_dev->err = -EIO;
> > - goto stop;
> > + return 1;
> > }
> >
> > /* Handle FIFO read */
> > @@ -196,18 +195,30 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> > } else {
> > /* Handle the remaining bytes which were not sent */
> > while (!(readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) &
> > - OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
> > + OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
> > writel(msg->buf[i2c_dev->msg_ptr++],
> > i2c_dev->base + OWL_I2C_REG_TXDAT);
> > }
> > }
> >
> > -stop:
> > + return 0;
> > +}
> > +
> > +static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> > +{
> > + struct owl_i2c_dev *i2c_dev = _dev;
> > + unsigned long flags;
> > +
> > + spin_lock_irqsave(&i2c_dev->lock, flags);
> > +
> > + owl_i2c_xfer_data(i2c_dev);
> > +
> > /* Clear pending interrupts */
> > owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT,
> > OWL_I2C_STAT_IRQP, true);
> >
> > complete_all(&i2c_dev->msg_complete);
> > +
> > spin_unlock_irqrestore(&i2c_dev->lock, flags);
> >
> > return IRQ_HANDLED;
> > @@ -235,8 +246,8 @@ static int owl_i2c_check_bus_busy(struct i2c_adapter *adap)
> > return 0;
> > }
> >
> > -static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> > - int num)
> > +static int owl_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg *msgs,
> > + int num, bool atomic)
> > {
> > struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
> > struct i2c_msg *msg;
> > @@ -280,11 +291,12 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> > goto err_exit;
> > }
> >
> > - reinit_completion(&i2c_dev->msg_complete);
> > + if (!atomic)
> > + reinit_completion(&i2c_dev->msg_complete);
> >
> > - /* Enable I2C controller interrupt */
> > + /* Enable/disable I2C controller interrupt */
> > owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
> > - OWL_I2C_CTL_IRQE, true);
> > + OWL_I2C_CTL_IRQE, !atomic);
> >
> > /*
> > * Select: FIFO enable, Master mode, Stop enable, Data count enable,
> > @@ -352,20 +364,33 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> >
> > spin_unlock_irqrestore(&i2c_dev->lock, flags);
> >
> > - time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
> > - adap->timeout);
> > + if (atomic) {
> > + /* Wait for Command Execute Completed or NACK Error bits */
> > + ret = readl_poll_timeout_atomic(i2c_dev->base + OWL_I2C_REG_FIFOSTAT,
> > + val, val & (OWL_I2C_FIFOSTAT_CECB |
> > + OWL_I2C_FIFOSTAT_RNB),
> > + 10, OWL_I2C_TIMEOUT_MS * 1000);
> > + } else {
> > + time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
> > + adap->timeout);
> > + if (!time_left)
> > + ret = -ETIMEDOUT;
> > + }
> >
> > spin_lock_irqsave(&i2c_dev->lock, flags);
> > - if (time_left == 0) {
> > +
> > + if (ret) {
> > dev_err(&adap->dev, "Transaction timed out\n");
> > /* Send stop condition and release the bus */
> > owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
> > OWL_I2C_CTL_GBCC_STOP | OWL_I2C_CTL_RB,
> > true);
> > - ret = -ETIMEDOUT;
> > goto err_exit;
> > }
> >
> > + if (atomic)
> > + owl_i2c_xfer_data(i2c_dev);
> > +
> > ret = i2c_dev->err < 0 ? i2c_dev->err : num;
> >
> > err_exit:
> > @@ -379,9 +404,22 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> > return ret;
> > }
> >
> > +static int owl_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> > + int num)
> > +{
> > + return owl_i2c_xfer_common(adap, msgs, num, false);
> > +}
> > +
> > +static int owl_i2c_xfer_atomic(struct i2c_adapter *adap,
> > + struct i2c_msg *msgs, int num)
> > +{
> > + return owl_i2c_xfer_common(adap, msgs, num, true);
> > +}
> > +
> > static const struct i2c_algorithm owl_i2c_algorithm = {
> > - .master_xfer = owl_i2c_master_xfer,
> > - .functionality = owl_i2c_func,
> > + .master_xfer = owl_i2c_xfer,
> > + .master_xfer_atomic = owl_i2c_xfer_atomic,
> > + .functionality = owl_i2c_func,
> > };
> >
> > static const struct i2c_adapter_quirks owl_i2c_quirks = {
> > --
> > 2.28.0
> >