> -----Original Message-----
> From: Martin Blumenstingl <[email protected]>
> Sent: Wednesday, December 28, 2022 7:30 AM
> To: [email protected]
> Cc: Yan-Hsuan Chuang <[email protected]>; Kalle Valo <[email protected]>; Ulf Hansson
> <[email protected]>; [email protected]; [email protected];
> [email protected]; Chris Morgan <[email protected]>; Nitin Gupta <[email protected]>;
> Neo Jou <[email protected]>; Ping-Ke Shih <[email protected]>; Jernej Skrabec <[email protected]>;
> Martin Blumenstingl <[email protected]>
> Subject: [RFC PATCH v1 13/19] rtw88: mac: Add support for SDIO specifics in the power on sequence
>
> Add the code specific to SDIO HCI in the MAC power on sequence. This is
> based on the RTL8822BS and RTL8822CS vendor drivers.
>
> Co-developed-by: Jernej Skrabec <[email protected]>
> Signed-off-by: Jernej Skrabec <[email protected]>
> Signed-off-by: Martin Blumenstingl <[email protected]>
> ---
> drivers/net/wireless/realtek/rtw88/mac.c | 41 ++++++++++++++++++++++--
> 1 file changed, 39 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/wireless/realtek/rtw88/mac.c b/drivers/net/wireless/realtek/rtw88/mac.c
> index 8e1fa824b32b..ad71f9838d1d 100644
> --- a/drivers/net/wireless/realtek/rtw88/mac.c
> +++ b/drivers/net/wireless/realtek/rtw88/mac.c
> @@ -7,6 +7,7 @@
> #include "reg.h"
> #include "fw.h"
> #include "debug.h"
> +#include "sdio.h"
>
> void rtw_set_channel_mac(struct rtw_dev *rtwdev, u8 channel, u8 bw,
> u8 primary_ch_idx)
> @@ -60,6 +61,7 @@ EXPORT_SYMBOL(rtw_set_channel_mac);
>
> static int rtw_mac_pre_system_cfg(struct rtw_dev *rtwdev)
> {
> + unsigned int retry;
> u32 value32;
> u8 value8;
>
> @@ -77,6 +79,26 @@ static int rtw_mac_pre_system_cfg(struct rtw_dev *rtwdev)
> case RTW_HCI_TYPE_PCIE:
> rtw_write32_set(rtwdev, REG_HCI_OPT_CTRL, BIT_USB_SUS_DIS);
> break;
> + case RTW_HCI_TYPE_SDIO:
> + rtw_write8_clr(rtwdev, REG_SDIO_HSUS_CTRL, BIT(0));
BIT_HCI_SUS_REQ BIT(0)
> +
> + for (retry = 0; retry < RTW_PWR_POLLING_CNT; retry++) {
> + if (rtw_read8(rtwdev, REG_SDIO_HSUS_CTRL) & BIT(1))
BIT_HCI_RESUME_RDY BIT(1)
> + break;
> +
> + usleep_range(10, 50);
> + }
> +
> + if (retry == RTW_PWR_POLLING_CNT) {
> + rtw_err(rtwdev, "failed to poll REG_SDIO_HSUS_CTRL[1]");
> + return -ETIMEDOUT;
> + }
> +
> + if (rtw_sdio_is_sdio30_supported(rtwdev))
> + rtw_write8_set(rtwdev, REG_HCI_OPT_CTRL + 2, BIT(2));
BIT_USB_LPM_ACT_EN BIT(10) // reg_addr +2, so bit >> 8
> + else
> + rtw_write8_clr(rtwdev, REG_HCI_OPT_CTRL + 2, BIT(2));
> + break;
> case RTW_HCI_TYPE_USB:
> break;
> default:
[...]