From: Ramuthevar Vadivel Murugan <[email protected]>
Add dt-bindings documentation for Cadence-QSPI controller to support
spi based flash memories.
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
---
.../devicetree/bindings/mtd/cadence-quadspi.txt | 67 -----------
.../devicetree/bindings/spi/cdns,qspi-nor.yaml | 127 +++++++++++++++++++++
2 files changed, 127 insertions(+), 67 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
- Generic default - "cdns,qspi-nor".
- For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
- For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
- physical address and length. The first entry is the address and
- length of the controller register set. The second entry is the
- address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
- the read data rather than the QSPI clock. Make sure that QSPI return
- clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
- mode chip select outputs are de-asserted between
- transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
- de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
- transaction and deasserting the device chip select
- (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
- and first bit transfer.
-- resets : Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names : Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
- qspi: spi@ff705000 {
- compatible = "cdns,qspi-nor";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0xff705000 0x1000>,
- <0xffa00000 0x1000>;
- interrupts = <0 151 4>;
- clocks = <&qspi_clk>;
- cdns,is-decoded-cs;
- cdns,fifo-depth = <128>;
- cdns,fifo-width = <4>;
- cdns,trigger-address = <0x00000000>;
- resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
- reset-names = "qspi", "qspi-ocp";
-
- flash0: n25q00@0 {
- ...
- cdns,read-delay = <4>;
- cdns,tshsl-ns = <50>;
- cdns,tsd2d-ns = <50>;
- cdns,tchsh-ns = <4>;
- cdns,tslch-ns = <4>;
- };
- };
diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
new file mode 100644
index 000000000000..28112b38e6a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Cadence QSPI Flash Controller support
+
+maintainers:
+ - Ramuthevar Vadivel Murugan <[email protected]>
+
+allOf:
+ - $ref: "spi-controller.yaml#"
+
+description: |
+ Binding Documentation for Cadence QSPI controller,This controller is
+ present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
+ has been tested On Intel's LGM SoC.
+
+properties:
+ compatible:
+ enum:
+ - cdns,qspi-nor
+ - ti,k2g-qspi
+ - ti,am654-ospi
+ - intel,lgm-qspi
+
+ reg:
+ maxItems: 2
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ cdns,fifo-depth:
+ description:
+ Depth of hardware FIFOs.
+ allOf:
+ - $ref: "/schemas/types.yaml#/definitions/uint32"
+ - enum: [ 128, 256 ]
+ - default: 128
+
+ cdns,fifo-width:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ 4 byte bus width of the data FIFO in bytes.
+
+ cdns,trigger-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ 32-bit indirect AHB trigger address.
+
+ cdns,rclk-en:
+ type: boolean
+ description: |
+ Flag to indicate that QSPI return clock is used to latch the read data
+ rather than the QSPI clock. Make sure that QSPI return clock is populated
+ on the board before using this property.
+
+# subnode's properties
+patternProperties:
+ "^.*@[0-9a-fa-f]+$":
+ type: object
+ description:
+ flash device uses the subnodes below defined properties.
+
+ cdns,read-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay for read capture logic, in clock cycles.
+
+ cdns,tshsl-ns:
+ description: |
+ Delay in nanoseconds for the length that the master mode chip select
+ outputs are de-asserted between transactions.
+
+ cdns,tsd2d-ns:
+ description: |
+ Delay in nanoseconds between one chip select being de-activated
+ and the activation of another.
+
+ cdns,tchsh-ns:
+ description: |
+ Delay in nanoseconds between last bit of current transaction and
+ deasserting the device chip select (qspi_n_ss_out).
+
+ cdns,tslch-ns:
+ description: |
+ Delay in nanoseconds between setting qspi_n_ss_out low and
+ first bit transfer.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - cdns,fifo-depth
+ - cdns,fifo-width
+ - cdns,trigger-address
+
+examples:
+ - |
+ spi@ff705000 {
+ compatible = "cdns,qspi-nor";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xff705000 0x1000>,
+ <0xffa00000 0x1000>;
+ interrupts = <0 151 4>;
+ clocks = <&qspi_clk>;
+ cdns,fifo-depth = <128>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x00000000>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ };
+ };
+
--
2.11.0
On Tue, May 12, 2020 at 08:49:19AM +0800, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <[email protected]>
>
> Add dt-bindings documentation for Cadence-QSPI controller to support
> spi based flash memories.
>
> Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
> ---
> .../devicetree/bindings/mtd/cadence-quadspi.txt | 67 -----------
> .../devicetree/bindings/spi/cdns,qspi-nor.yaml | 127 +++++++++++++++++++++
> 2 files changed, 127 insertions(+), 67 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
> create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>
> diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
> deleted file mode 100644
> index 945be7d5b236..000000000000
> --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,67 +0,0 @@
> -* Cadence Quad SPI controller
> -
> -Required properties:
> -- compatible : should be one of the following:
> - Generic default - "cdns,qspi-nor".
> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
> -- reg : Contains two entries, each of which is a tuple consisting of a
> - physical address and length. The first entry is the address and
> - length of the controller register set. The second entry is the
> - address and length of the QSPI Controller data area.
> -- interrupts : Unit interrupt specifier for the controller interrupt.
> -- clocks : phandle to the Quad SPI clock.
> -- cdns,fifo-depth : Size of the data FIFO in words.
> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> -
> -Optional properties:
> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> - the read data rather than the QSPI clock. Make sure that QSPI return
> - clock is populated on the board before using this property.
> -
> -Optional subnodes:
> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> -custom properties:
> -- cdns,read-delay : Delay for read capture logic, in clock cycles
> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> - mode chip select outputs are de-asserted between
> - transactions.
> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> - de-activated and the activation of another.
> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> - transaction and deasserting the device chip select
> - (qspi_n_ss_out).
> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> - and first bit transfer.
> -- resets : Must contain an entry for each entry in reset-names.
> - See ../reset/reset.txt for details.
> -- reset-names : Must include either "qspi" and/or "qspi-ocp".
> -
> -Example:
> -
> - qspi: spi@ff705000 {
> - compatible = "cdns,qspi-nor";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0xff705000 0x1000>,
> - <0xffa00000 0x1000>;
> - interrupts = <0 151 4>;
> - clocks = <&qspi_clk>;
> - cdns,is-decoded-cs;
> - cdns,fifo-depth = <128>;
> - cdns,fifo-width = <4>;
> - cdns,trigger-address = <0x00000000>;
> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> - reset-names = "qspi", "qspi-ocp";
> -
> - flash0: n25q00@0 {
> - ...
> - cdns,read-delay = <4>;
> - cdns,tshsl-ns = <50>;
> - cdns,tsd2d-ns = <50>;
> - cdns,tchsh-ns = <4>;
> - cdns,tslch-ns = <4>;
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
> new file mode 100644
> index 000000000000..28112b38e6a9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
> @@ -0,0 +1,127 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Cadence QSPI Flash Controller support
> +
> +maintainers:
> + - Ramuthevar Vadivel Murugan <[email protected]>
> +
> +allOf:
> + - $ref: "spi-controller.yaml#"
> +
> +description: |
> + Binding Documentation for Cadence QSPI controller,This controller is
> + present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
> + has been tested On Intel's LGM SoC.
> +
> +properties:
> + compatible:
> + enum:
> + - cdns,qspi-nor
> + - ti,k2g-qspi
> + - ti,am654-ospi
> + - intel,lgm-qspi
> +
> + reg:
> + maxItems: 2
Need to define what each entry is.
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + cdns,fifo-depth:
> + description:
> + Depth of hardware FIFOs.
...FIFO in words.
> + allOf:
> + - $ref: "/schemas/types.yaml#/definitions/uint32"
> + - enum: [ 128, 256 ]
> + - default: 128
> +
> + cdns,fifo-width:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description:
> + 4 byte bus width of the data FIFO in bytes.
Constraints? Perhaps:
multipleOf: 4
if an enum doesn't work here.
> +
> + cdns,trigger-address:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description:
> + 32-bit indirect AHB trigger address.
> +
> + cdns,rclk-en:
> + type: boolean
> + description: |
> + Flag to indicate that QSPI return clock is used to latch the read data
> + rather than the QSPI clock. Make sure that QSPI return clock is populated
> + on the board before using this property.
> +
> +# subnode's properties
> +patternProperties:
> + "^.*@[0-9a-fa-f]+$":
'a-f' is twice. What's the max number of chip selects? If less than 10,
then '@[0-9]$' is enough. '^.*' can be dropped too.
> + type: object
> + description:
> + flash device uses the subnodes below defined properties.
> +
> + cdns,read-delay:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + description:
> + Delay for read capture logic, in clock cycles.
> +
> + cdns,tshsl-ns:
> + description: |
> + Delay in nanoseconds for the length that the master mode chip select
> + outputs are de-asserted between transactions.
> +
> + cdns,tsd2d-ns:
> + description: |
> + Delay in nanoseconds between one chip select being de-activated
> + and the activation of another.
> +
> + cdns,tchsh-ns:
> + description: |
> + Delay in nanoseconds between last bit of current transaction and
> + deasserting the device chip select (qspi_n_ss_out).
> +
> + cdns,tslch-ns:
> + description: |
> + Delay in nanoseconds between setting qspi_n_ss_out low and
> + first bit transfer.
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - clocks
> + - cdns,fifo-depth
> + - cdns,fifo-width
> + - cdns,trigger-address
> +
> +examples:
> + - |
> + spi@ff705000 {
> + compatible = "cdns,qspi-nor";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0xff705000 0x1000>,
> + <0xffa00000 0x1000>;
Seems kind of small for a data area if this is like most SPI flash
controllers.
> + interrupts = <0 151 4>;
> + clocks = <&qspi_clk>;
> + cdns,fifo-depth = <128>;
> + cdns,fifo-width = <4>;
> + cdns,trigger-address = <0x00000000>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + cdns,read-delay = <4>;
> + cdns,tshsl-ns = <50>;
> + cdns,tsd2d-ns = <50>;
> + cdns,tchsh-ns = <4>;
> + cdns,tslch-ns = <4>;
> + };
> + };
> +
> --
> 2.11.0
>
Hi Rob,
Thank you very much for the review comments...
On 20/5/2020 2:44 am, Rob Herring wrote:
> On Tue, May 12, 2020 at 08:49:19AM +0800, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <[email protected]>
>>
>> Add dt-bindings documentation for Cadence-QSPI controller to support
>> spi based flash memories.
>>
>> Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
>> ---
>> .../devicetree/bindings/mtd/cadence-quadspi.txt | 67 -----------
>> .../devicetree/bindings/spi/cdns,qspi-nor.yaml | 127 +++++++++++++++++++++
>> 2 files changed, 127 insertions(+), 67 deletions(-)
>> delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>> create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>> deleted file mode 100644
>> index 945be7d5b236..000000000000
>> --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>> +++ /dev/null
>> @@ -1,67 +0,0 @@
>> -* Cadence Quad SPI controller
>> -
>> -Required properties:
>> -- compatible : should be one of the following:
>> - Generic default - "cdns,qspi-nor".
>> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
>> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
>> -- reg : Contains two entries, each of which is a tuple consisting of a
>> - physical address and length. The first entry is the address and
>> - length of the controller register set. The second entry is the
>> - address and length of the QSPI Controller data area.
>> -- interrupts : Unit interrupt specifier for the controller interrupt.
>> -- clocks : phandle to the Quad SPI clock.
>> -- cdns,fifo-depth : Size of the data FIFO in words.
>> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
>> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
>> -
>> -Optional properties:
>> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
>> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
>> - the read data rather than the QSPI clock. Make sure that QSPI return
>> - clock is populated on the board before using this property.
>> -
>> -Optional subnodes:
>> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
>> -custom properties:
>> -- cdns,read-delay : Delay for read capture logic, in clock cycles
>> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
>> - mode chip select outputs are de-asserted between
>> - transactions.
>> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
>> - de-activated and the activation of another.
>> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
>> - transaction and deasserting the device chip select
>> - (qspi_n_ss_out).
>> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
>> - and first bit transfer.
>> -- resets : Must contain an entry for each entry in reset-names.
>> - See ../reset/reset.txt for details.
>> -- reset-names : Must include either "qspi" and/or "qspi-ocp".
>> -
>> -Example:
>> -
>> - qspi: spi@ff705000 {
>> - compatible = "cdns,qspi-nor";
>> - #address-cells = <1>;
>> - #size-cells = <0>;
>> - reg = <0xff705000 0x1000>,
>> - <0xffa00000 0x1000>;
>> - interrupts = <0 151 4>;
>> - clocks = <&qspi_clk>;
>> - cdns,is-decoded-cs;
>> - cdns,fifo-depth = <128>;
>> - cdns,fifo-width = <4>;
>> - cdns,trigger-address = <0x00000000>;
>> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
>> - reset-names = "qspi", "qspi-ocp";
>> -
>> - flash0: n25q00@0 {
>> - ...
>> - cdns,read-delay = <4>;
>> - cdns,tshsl-ns = <50>;
>> - cdns,tsd2d-ns = <50>;
>> - cdns,tchsh-ns = <4>;
>> - cdns,tslch-ns = <4>;
>> - };
>> - };
>> diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>> new file mode 100644
>> index 000000000000..28112b38e6a9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>> @@ -0,0 +1,127 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: "http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#"
>> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
>> +
>> +title: Cadence QSPI Flash Controller support
>> +
>> +maintainers:
>> + - Ramuthevar Vadivel Murugan <[email protected]>
>> +
>> +allOf:
>> + - $ref: "spi-controller.yaml#"
>> +
>> +description: |
>> + Binding Documentation for Cadence QSPI controller,This controller is
>> + present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
>> + has been tested On Intel's LGM SoC.
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - cdns,qspi-nor
>> + - ti,k2g-qspi
>> + - ti,am654-ospi
>> + - intel,lgm-qspi
>> +
>> + reg:
>> + maxItems: 2
>
> Need to define what each entry is.
Noted.
>
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + cdns,fifo-depth:
>> + description:
>> + Depth of hardware FIFOs.
>
> ...FIFO in words.
Good catch.
>
>> + allOf:
>> + - $ref: "/schemas/types.yaml#/definitions/uint32"
>> + - enum: [ 128, 256 ]
>> + - default: 128
>> +
>> + cdns,fifo-width:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description:
>> + 4 byte bus width of the data FIFO in bytes.
>
> Constraints? Perhaps:
>
> multipleOf: 4
Noted, will update.
>
> if an enum doesn't work here.
>
>> +
>> + cdns,trigger-address:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description:
>> + 32-bit indirect AHB trigger address.
>> +
>> + cdns,rclk-en:
>> + type: boolean
>> + description: |
>> + Flag to indicate that QSPI return clock is used to latch the read data
>> + rather than the QSPI clock. Make sure that QSPI return clock is populated
>> + on the board before using this property.
>> +
>> +# subnode's properties
>> +patternProperties:
>> + "^.*@[0-9a-fa-f]+$":
>
> 'a-f' is twice. What's the max number of chip selects? If less than 10,
> then '@[0-9]$' is enough. '^.*' can be dropped too.
16 chip select supports.
>
>> + type: object
>> + description:
>> + flash device uses the subnodes below defined properties.
>> +
>> + cdns,read-delay:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description:
>> + Delay for read capture logic, in clock cycles.
>> +
>> + cdns,tshsl-ns:
>> + description: |
>> + Delay in nanoseconds for the length that the master mode chip select
>> + outputs are de-asserted between transactions.
>> +
>> + cdns,tsd2d-ns:
>> + description: |
>> + Delay in nanoseconds between one chip select being de-activated
>> + and the activation of another.
>> +
>> + cdns,tchsh-ns:
>> + description: |
>> + Delay in nanoseconds between last bit of current transaction and
>> + deasserting the device chip select (qspi_n_ss_out).
>> +
>> + cdns,tslch-ns:
>> + description: |
>> + Delay in nanoseconds between setting qspi_n_ss_out low and
>> + first bit transfer.
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - interrupts
>> + - clocks
>> + - cdns,fifo-depth
>> + - cdns,fifo-width
>> + - cdns,trigger-address
>> +
>> +examples:
>> + - |
>> + spi@ff705000 {
>> + compatible = "cdns,qspi-nor";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <0xff705000 0x1000>,
>> + <0xffa00000 0x1000>;
>
> Seems kind of small for a data area if this is like most SPI flash
> controllers.yes you are right, following the existing example as it is.
Regards
Vadivel
>
>> + interrupts = <0 151 4>;
>> + clocks = <&qspi_clk>;
>> + cdns,fifo-depth = <128>;
>> + cdns,fifo-width = <4>;
>> + cdns,trigger-address = <0x00000000>;
>> +
>> + flash@0 {
>> + compatible = "jedec,spi-nor";
>> + reg = <0x0>;
>> + cdns,read-delay = <4>;
>> + cdns,tshsl-ns = <50>;
>> + cdns,tsd2d-ns = <50>;
>> + cdns,tchsh-ns = <4>;
>> + cdns,tslch-ns = <4>;
>> + };
>> + };
>> +
>> --
>> 2.11.0
>>