Add some device nodes for board AQ222,
including clock,I2C,SPICC,nand and ethernet.
Signed-off-by: Xianwei Zhao <[email protected]>
---
.../dts/amlogic/meson-s4-s805x2-aq222.dts | 55 +++
arch/arm64/boot/dts/amlogic/meson-s4.dtsi | 350 +++++++++++++++++-
2 files changed, 404 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
index c1f322c73982..fd349c49ebf5 100644
--- a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
@@ -23,6 +23,16 @@ memory@0 {
reg = <0x0 0x0 0x0 0x40000000>;
};
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secmon_reserved: secmon@5000000 {
+ reg = <0x0 0x05000000 0x0 0x4000000>;
+ no-map;
+ };
+ };
};
&uart_B {
@@ -34,3 +44,48 @@ &ir {
pinctrl-0 = <&remote_pins>;
pinctrl-names = "default";
};
+
+&nand {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nand-on-flash-bbt;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x0 0x00200000>;
+ };
+ partition@200000 {
+ label = "env";
+ reg = <0x00200000 0x00400000>;
+ };
+ partition@600000 {
+ label = "system";
+ reg = <0x00600000 0x00a00000>;
+ };
+ partition@1000000 {
+ label = "rootfs";
+ reg = <0x01000000 0x03000000>;
+ };
+ partition@4000000 {
+ label = "media";
+ reg = <0x04000000 0x8000000>;
+ };
+ };
+};
+
+&spicc0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spicc0_pins_x>;
+ cs-gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
index 2344b2d741c3..022aba0f9ef7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
@@ -6,6 +6,10 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/gpio/meson-s4-gpio.h>
+#include <dt-bindings/clock/amlogic,s4-pll-clkc.h>
+#include <dt-bindings/clock/amlogic,s4-peripherals-clkc.h>
+#include <dt-bindings/power/meson-s4-power.h>
/ {
cpus {
@@ -92,6 +96,38 @@ apb4: bus@fe000000 {
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+ clkc_periphs: clock-controller@0 {
+ compatible = "amlogic,s4-peripherals-clkc";
+ reg = <0x0 0x0 0x0 0x49c>;
+ clocks = <&clkc_pll CLKID_FCLK_DIV2>,
+ <&clkc_pll CLKID_FCLK_DIV2P5>,
+ <&clkc_pll CLKID_FCLK_DIV3>,
+ <&clkc_pll CLKID_FCLK_DIV4>,
+ <&clkc_pll CLKID_FCLK_DIV5>,
+ <&clkc_pll CLKID_FCLK_DIV7>,
+ <&clkc_pll CLKID_HIFI_PLL>,
+ <&clkc_pll CLKID_GP0_PLL>,
+ <&clkc_pll CLKID_MPLL0>,
+ <&clkc_pll CLKID_MPLL1>,
+ <&clkc_pll CLKID_MPLL2>,
+ <&clkc_pll CLKID_MPLL3>,
+ <&clkc_pll CLKID_HDMI_PLL>,
+ <&xtal>;
+ clock-names = "fclk_div2", "fclk_div2p5", "fclk_div3",
+ "fclk_div4", "fclk_div5", "fclk_div7",
+ "hifi_pll", "gp0_pll", "mpll0", "mpll1",
+ "mpll2", "mpll3", "hdmi_pll", "xtal";
+ #clock-cells = <1>;
+ };
+
+ clkc_pll: clock-controller@8000 {
+ compatible = "amlogic,s4-pll-clkc";
+ reg = <0x0 0x8000 0x0 0x1e8>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
+ #clock-cells = <1>;
+ };
+
watchdog@2100 {
compatible = "amlogic,s4-wdt", "amlogic,t7-wdt";
reg = <0x0 0x2100 0x0 0x10>;
@@ -120,6 +156,187 @@ mux {
bias-disable;
};
};
+
+ i2c0_pins1:i2c0-pins1 {
+ mux {
+ groups = "i2c0_sda",
+ "i2c0_scl";
+ function = "i2c0";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c1_pins1:i2c1-pins1 {
+ mux {
+ groups = "i2c1_sda_c",
+ "i2c1_scl_c";
+ function = "i2c1";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c1_pins2:i2c1-pins2 {
+ mux {
+ groups = "i2c1_sda_d",
+ "i2c1_scl_d";
+ function = "i2c1";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c1_pins3:i2c1-pins3 {
+ mux {
+ groups = "i2c1_sda_h",
+ "i2c1_scl_h";
+ function = "i2c1";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c1_pins4:i2c1-pins4 {
+ mux {
+ groups = "i2c1_sda_x",
+ "i2c1_scl_x";
+ function = "i2c1";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c2_pins1:i2c2-pins1 {
+ mux {
+ groups = "i2c2_sda_d",
+ "i2c2_scl_d";
+ function = "i2c2";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c2_pins2:i2c2-pins2 {
+ mux {
+ groups = "i2c2_sda_h8",
+ "i2c2_scl_h9";
+ function = "i2c2";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c2_pins3:i2c2-pins3 {
+ mux {
+ groups = "i2c2_sda_h0",
+ "i2c2_scl_h1";
+ function = "i2c2";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c3_pins1:i2c3-pins1 {
+ mux {
+ groups = "i2c3_sda_x",
+ "i2c3_scl_x";
+ function = "i2c3";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c3_pins2:i2c3-pins2 {
+ mux {
+ groups = "i2c3_sda_z",
+ "i2c3_scl_z";
+ function = "i2c3";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c4_pins1:i2c4-pins1 {
+ mux {
+ groups = "i2c4_sda_c",
+ "i2c4_scl_c";
+ function = "i2c4";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c4_pins2:i2c4-pins2 {
+ mux {
+ groups = "i2c4_sda_d",
+ "i2c4_scl_d";
+ function = "i2c4";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ i2c4_pins3:i2c4-pins3 {
+ mux {
+ groups = "i2c4_sda_z",
+ "i2c4_scl_z";
+ function = "i2c4";
+ drive-strength-microamp = <3000>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand-pins {
+ mux {
+ groups = "emmc_nand_d0",
+ "emmc_nand_d1",
+ "emmc_nand_d2",
+ "emmc_nand_d3",
+ "emmc_nand_d4",
+ "emmc_nand_d5",
+ "emmc_nand_d6",
+ "emmc_nand_d7",
+ "nand_ce0",
+ "nand_ale",
+ "nand_cle",
+ "nand_wen_clk",
+ "nand_ren_wr";
+ function = "nand";
+ input-enable;
+ };
+ };
+
+ spicc0_pins_x: spicc0-pins_x {
+ mux {
+ groups = "spi_a_mosi_x",
+ "spi_a_miso_x",
+ "spi_a_clk_x";
+ function = "spi_a";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spicc0_pins_h: spicc0-pins-h {
+ mux {
+ groups = "spi_a_mosi_h",
+ "spi_a_miso_h",
+ "spi_a_clk_h";
+ function = "spi_a";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spicc0_pins_z: spicc0-pins-z {
+ mux {
+ groups = "spi_a_mosi_z",
+ "spi_a_miso_z",
+ "spi_a_clk_z";
+ function = "spi_a";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
};
gpio_intc: interrupt-controller@4080 {
@@ -132,13 +349,119 @@ gpio_intc: interrupt-controller@4080 {
<10 11 12 13 14 15 16 17 18 19 20 21>;
};
+ eth_phy: mdio-multiplexer@28000 {
+ compatible = "amlogic,g12a-mdio-mux";
+ reg = <0x0 0x28000 0x0 0xa4>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc_periphs CLKID_ETHPHY>,
+ <&xtal>,
+ <&clkc_pll CLKID_MPLL_50M>;
+ clock-names = "pclk", "clkin0", "clkin1";
+ mdio-parent-bus = <&mdio0>;
+
+ ext_mdio: mdio@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ int_mdio: mdio@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ internal_ephy: ethernet-phy@8 {
+ compatible = "ethernet-phy-id0180.3301",
+ "ethernet-phy-ieee802.3-c22";
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <8>;
+ max-speed = <100>;
+ };
+ };
+ };
+
+ spicc0: spi@50000 {
+ compatible = "amlogic,meson-g12a-spicc";
+ reg = <0x0 0x50000 0x0 0x44>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc_periphs CLKID_SPICC0>,
+ <&clkc_periphs CLKID_SPICC0_EN>;
+ clock-names = "core", "pclk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@66000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x66000 0x0 0x20>;
+ interrupts = <GIC_SPI 160 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_I2C_M_A>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@68000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x68000 0x0 0x20>;
+ interrupts = <GIC_SPI 161 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_I2C_M_B>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@6a000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x6a000 0x0 0x20>;
+ interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_I2C_M_C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@6c000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x6c000 0x0 0x20>;
+ interrupts = <GIC_SPI 163 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_I2C_M_D>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@6e000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x6e000 0x0 0x20>;
+ interrupts = <GIC_SPI 164 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_I2C_M_E>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ nand: nand-controller@8c800 {
+ compatible = "amlogic,meson-axg-nfc";
+ reg = <0x0 0x8c800 0x0 0x100>, <0x0 0x8c000 0x0 0x4>;
+ reg-names = "nfc", "emmc";
+ interrupts = <GIC_SPI 175 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_SD_EMMC_C>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core", "device";
+ status = "disabled";
+ };
+
uart_B: serial@7a000 {
compatible = "amlogic,meson-s4-uart",
"amlogic,meson-ao-uart";
reg = <0x0 0x7a000 0x0 0x18>;
interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
- clocks = <&xtal>, <&xtal>, <&xtal>;
+ clocks = <&xtal>, <&clkc_periphs CLKID_UART_B>, <&xtal>;
clock-names = "xtal", "pclk", "baud";
};
@@ -160,5 +483,30 @@ hwrng: rng@440788 {
reg = <0x0 0x440788 0x0 0x0c>;
};
};
+
+ ethmac: ethernet@fdc00000 {
+ compatible = "amlogic,meson-axg-dwmac",
+ "snps,dwmac-3.70a",
+ "snps,dwmac";
+ reg = <0x0 0xfdc00000 0x0 0x10000>,
+ <0x0 0xfe024000 0x0 0x8>;
+
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ power-domains = <&pwrc PWRC_S4_ETH_ID>;
+ clocks = <&clkc_periphs CLKID_ETH>,
+ <&clkc_pll CLKID_FCLK_DIV2>,
+ <&clkc_pll CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+ rx-fifo-depth = <4096>;
+ tx-fifo-depth = <2048>;
+ status = "disabled";
+
+ mdio0: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+ };
};
};
base-commit: 3a5038e9c0556e51db96c2f7149d853efb886c95
--
2.39.2
Hi,
On 29/11/2023 10:29, Xianwei Zhao wrote:
> Add some device nodes for board AQ222,
> including clock,I2C,SPICC,nand and ethernet.
Could you reformat a little bit the commit message, it's a little bit scarce
and the style is weird.
>
> Signed-off-by: Xianwei Zhao <[email protected]>
> ---
> .../dts/amlogic/meson-s4-s805x2-aq222.dts | 55 +++
> arch/arm64/boot/dts/amlogic/meson-s4.dtsi | 350 +++++++++++++++++-
> 2 files changed, 404 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
> index c1f322c73982..fd349c49ebf5 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
Please move the meson-s4-s805x2-aq222.dts changes in a separate commit
> @@ -23,6 +23,16 @@ memory@0 {
> reg = <0x0 0x0 0x0 0x40000000>;
> };
>
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + secmon_reserved: secmon@5000000 {
> + reg = <0x0 0x05000000 0x0 0x4000000>;
> + no-map;
> + };
Please add a comment before the node explaining what needs this memory
> + };
> };
>
> &uart_B {
> @@ -34,3 +44,48 @@ &ir {
> pinctrl-0 = <&remote_pins>;
> pinctrl-names = "default";
> };
> +
> +&nand {
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pinctrl-0 = <&nand_pins>;
> + pinctrl-names = "default";
> +
> + nand@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + nand-on-flash-bbt;
> +
> + partition@0 {
> + label = "boot";
> + reg = <0x0 0x00200000>;
> + };
> + partition@200000 {
> + label = "env";
> + reg = <0x00200000 0x00400000>;
> + };
> + partition@600000 {
> + label = "system";
> + reg = <0x00600000 0x00a00000>;
> + };
> + partition@1000000 {
> + label = "rootfs";
> + reg = <0x01000000 0x03000000>;
> + };
> + partition@4000000 {
> + label = "media";
> + reg = <0x04000000 0x8000000>;
> + };
> + };
> +};
> +
> +&spicc0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spicc0_pins_x>;
> + cs-gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
> index 2344b2d741c3..022aba0f9ef7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
> @@ -6,6 +6,10 @@
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/gpio/meson-s4-gpio.h>
> +#include <dt-bindings/clock/amlogic,s4-pll-clkc.h>
> +#include <dt-bindings/clock/amlogic,s4-peripherals-clkc.h>
> +#include <dt-bindings/power/meson-s4-power.h>
>
> / {
> cpus {
> @@ -92,6 +96,38 @@ apb4: bus@fe000000 {
> #size-cells = <2>;
> ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
>
> + clkc_periphs: clock-controller@0 {
> + compatible = "amlogic,s4-peripherals-clkc";
> + reg = <0x0 0x0 0x0 0x49c>;
> + clocks = <&clkc_pll CLKID_FCLK_DIV2>,
> + <&clkc_pll CLKID_FCLK_DIV2P5>,
> + <&clkc_pll CLKID_FCLK_DIV3>,
> + <&clkc_pll CLKID_FCLK_DIV4>,
> + <&clkc_pll CLKID_FCLK_DIV5>,
> + <&clkc_pll CLKID_FCLK_DIV7>,
> + <&clkc_pll CLKID_HIFI_PLL>,
> + <&clkc_pll CLKID_GP0_PLL>,
> + <&clkc_pll CLKID_MPLL0>,
> + <&clkc_pll CLKID_MPLL1>,
> + <&clkc_pll CLKID_MPLL2>,
> + <&clkc_pll CLKID_MPLL3>,
> + <&clkc_pll CLKID_HDMI_PLL>,
> + <&xtal>;
> + clock-names = "fclk_div2", "fclk_div2p5", "fclk_div3",
> + "fclk_div4", "fclk_div5", "fclk_div7",
> + "hifi_pll", "gp0_pll", "mpll0", "mpll1",
> + "mpll2", "mpll3", "hdmi_pll", "xtal";
> + #clock-cells = <1>;
> + };
> +
> + clkc_pll: clock-controller@8000 {
> + compatible = "amlogic,s4-pll-clkc";
> + reg = <0x0 0x8000 0x0 0x1e8>;
> + clocks = <&xtal>;
> + clock-names = "xtal";
> + #clock-cells = <1>;
> + };
> +
> watchdog@2100 {
> compatible = "amlogic,s4-wdt", "amlogic,t7-wdt";
> reg = <0x0 0x2100 0x0 0x10>;
> @@ -120,6 +156,187 @@ mux {
> bias-disable;
> };
> };
> +
> + i2c0_pins1:i2c0-pins1 {
Please add a space after ":"
> + mux {
> + groups = "i2c0_sda",
> + "i2c0_scl";
> + function = "i2c0";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c1_pins1:i2c1-pins1 {
Ditto
> + mux {
> + groups = "i2c1_sda_c",
> + "i2c1_scl_c";
> + function = "i2c1";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c1_pins2:i2c1-pins2 {
Ditto
> + mux {
> + groups = "i2c1_sda_d",
> + "i2c1_scl_d";
> + function = "i2c1";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c1_pins3:i2c1-pins3 {
Ditto
> + mux {
> + groups = "i2c1_sda_h",
> + "i2c1_scl_h";
> + function = "i2c1";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c1_pins4:i2c1-pins4 {
Ditto
> + mux {
> + groups = "i2c1_sda_x",
> + "i2c1_scl_x";
> + function = "i2c1";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c2_pins1:i2c2-pins1 {
> + mux {
> + groups = "i2c2_sda_d",
> + "i2c2_scl_d";
> + function = "i2c2";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c2_pins2:i2c2-pins2 {
> + mux {
> + groups = "i2c2_sda_h8",
> + "i2c2_scl_h9";
> + function = "i2c2";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c2_pins3:i2c2-pins3 {
Ditto
> + mux {
> + groups = "i2c2_sda_h0",
> + "i2c2_scl_h1";
> + function = "i2c2";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c3_pins1:i2c3-pins1 {
Ditto
> + mux {
> + groups = "i2c3_sda_x",
> + "i2c3_scl_x";
> + function = "i2c3";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c3_pins2:i2c3-pins2 {
Ditto
> + mux {
> + groups = "i2c3_sda_z",
> + "i2c3_scl_z";
> + function = "i2c3";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c4_pins1:i2c4-pins1 {
Ditto
> + mux {
> + groups = "i2c4_sda_c",
> + "i2c4_scl_c";
> + function = "i2c4";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c4_pins2:i2c4-pins2 {
Ditto
> + mux {
> + groups = "i2c4_sda_d",
> + "i2c4_scl_d";
> + function = "i2c4";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + i2c4_pins3:i2c4-pins3 {
Ditto
> + mux {
> + groups = "i2c4_sda_z",
> + "i2c4_scl_z";
> + function = "i2c4";
> + drive-strength-microamp = <3000>;
> + bias-disable;
> + };
> + };
> +
> + nand_pins: nand-pins {
> + mux {
> + groups = "emmc_nand_d0",
> + "emmc_nand_d1",
> + "emmc_nand_d2",
> + "emmc_nand_d3",
> + "emmc_nand_d4",
> + "emmc_nand_d5",
> + "emmc_nand_d6",
> + "emmc_nand_d7",
> + "nand_ce0",
> + "nand_ale",
> + "nand_cle",
> + "nand_wen_clk",
> + "nand_ren_wr";
> + function = "nand";
> + input-enable;
> + };
> + };
> +
> + spicc0_pins_x: spicc0-pins_x {
> + mux {
> + groups = "spi_a_mosi_x",
> + "spi_a_miso_x",
> + "spi_a_clk_x";
> + function = "spi_a";
> + drive-strength-microamp = <3000>;
> + };
> + };
> +
> + spicc0_pins_h: spicc0-pins-h {
> + mux {
> + groups = "spi_a_mosi_h",
> + "spi_a_miso_h",
> + "spi_a_clk_h";
> + function = "spi_a";
> + drive-strength-microamp = <3000>;
> + };
> + };
> +
> + spicc0_pins_z: spicc0-pins-z {
> + mux {
> + groups = "spi_a_mosi_z",
> + "spi_a_miso_z",
> + "spi_a_clk_z";
> + function = "spi_a";
> + drive-strength-microamp = <3000>;
> + };
> + };
> +
> };
>
> gpio_intc: interrupt-controller@4080 {
> @@ -132,13 +349,119 @@ gpio_intc: interrupt-controller@4080 {
> <10 11 12 13 14 15 16 17 18 19 20 21>;
> };
>
> + eth_phy: mdio-multiplexer@28000 {
> + compatible = "amlogic,g12a-mdio-mux";
> + reg = <0x0 0x28000 0x0 0xa4>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&clkc_periphs CLKID_ETHPHY>,
> + <&xtal>,
> + <&clkc_pll CLKID_MPLL_50M>;
> + clock-names = "pclk", "clkin0", "clkin1";
> + mdio-parent-bus = <&mdio0>;
> +
> + ext_mdio: mdio@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + int_mdio: mdio@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + internal_ephy: ethernet-phy@8 {
> + compatible = "ethernet-phy-id0180.3301",
> + "ethernet-phy-ieee802.3-c22";
> + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <8>;
> + max-speed = <100>;
> + };
> + };
> + };
> +
> + spicc0: spi@50000 {
> + compatible = "amlogic,meson-g12a-spicc";
> + reg = <0x0 0x50000 0x0 0x44>;
> + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clkc_periphs CLKID_SPICC0>,
> + <&clkc_periphs CLKID_SPICC0_EN>;
> + clock-names = "core", "pclk";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c0: i2c@66000 {
> + compatible = "amlogic,meson-axg-i2c";
> + reg = <0x0 0x66000 0x0 0x20>;
> + interrupts = <GIC_SPI 160 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc_periphs CLKID_I2C_M_A>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c@68000 {
> + compatible = "amlogic,meson-axg-i2c";
> + reg = <0x0 0x68000 0x0 0x20>;
> + interrupts = <GIC_SPI 161 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc_periphs CLKID_I2C_M_B>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@6a000 {
> + compatible = "amlogic,meson-axg-i2c";
> + reg = <0x0 0x6a000 0x0 0x20>;
> + interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc_periphs CLKID_I2C_M_C>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c@6c000 {
> + compatible = "amlogic,meson-axg-i2c";
> + reg = <0x0 0x6c000 0x0 0x20>;
> + interrupts = <GIC_SPI 163 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc_periphs CLKID_I2C_M_D>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c@6e000 {
> + compatible = "amlogic,meson-axg-i2c";
> + reg = <0x0 0x6e000 0x0 0x20>;
> + interrupts = <GIC_SPI 164 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc_periphs CLKID_I2C_M_E>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + nand: nand-controller@8c800 {
> + compatible = "amlogic,meson-axg-nfc";
> + reg = <0x0 0x8c800 0x0 0x100>, <0x0 0x8c000 0x0 0x4>;
> + reg-names = "nfc", "emmc";
> + interrupts = <GIC_SPI 175 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc_periphs CLKID_SD_EMMC_C>,
> + <&clkc_pll CLKID_FCLK_DIV2>;
> + clock-names = "core", "device";
> + status = "disabled";
> + };
> +
> uart_B: serial@7a000 {
> compatible = "amlogic,meson-s4-uart",
> "amlogic,meson-ao-uart";
> reg = <0x0 0x7a000 0x0 0x18>;
> interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
> status = "disabled";
> - clocks = <&xtal>, <&xtal>, <&xtal>;
> + clocks = <&xtal>, <&clkc_periphs CLKID_UART_B>, <&xtal>;
> clock-names = "xtal", "pclk", "baud";
> };
>
> @@ -160,5 +483,30 @@ hwrng: rng@440788 {
> reg = <0x0 0x440788 0x0 0x0c>;
> };
> };
> +
> + ethmac: ethernet@fdc00000 {
> + compatible = "amlogic,meson-axg-dwmac",
> + "snps,dwmac-3.70a",
> + "snps,dwmac";
> + reg = <0x0 0xfdc00000 0x0 0x10000>,
> + <0x0 0xfe024000 0x0 0x8>;
> +
> + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "macirq";
> + power-domains = <&pwrc PWRC_S4_ETH_ID>;
> + clocks = <&clkc_periphs CLKID_ETH>,
> + <&clkc_pll CLKID_FCLK_DIV2>,
> + <&clkc_pll CLKID_MPLL2>;
> + clock-names = "stmmaceth", "clkin0", "clkin1";
> + rx-fifo-depth = <4096>;
> + tx-fifo-depth = <2048>;
> + status = "disabled";
> +
> + mdio0: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + };
> + };
> };
> };
>
> base-commit: 3a5038e9c0556e51db96c2f7149d853efb886c95
Thanks,
Neil
Hi Neil,
Thanks for your review.
On 2023/11/29 18:42, Neil Armstrong wrote:
> [ EXTERNAL EMAIL ]
>
> Hi,
>
> On 29/11/2023 10:29, Xianwei Zhao wrote:
>> Add some device nodes for board AQ222,
>> including clock,I2C,SPICC,nand and ethernet.
>
> Could you reformat a little bit the commit message, it's a little bit
> scarce
> and the style is weird.
>
Will do.
>>
>> Signed-off-by: Xianwei Zhao <[email protected]>
>> ---
>> .../dts/amlogic/meson-s4-s805x2-aq222.dts | 55 +++
>> arch/arm64/boot/dts/amlogic/meson-s4.dtsi | 350 +++++++++++++++++-
>> 2 files changed, 404 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
>> b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
>> index c1f322c73982..fd349c49ebf5 100644
>> --- a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
>> +++ b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
>
> Please move the meson-s4-s805x2-aq222.dts changes in a separate commit
>
Will do.
>> @@ -23,6 +23,16 @@ memory@0 {
>> reg = <0x0 0x0 0x0 0x40000000>;
>> };
>>
>> + reserved-memory {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + secmon_reserved: secmon@5000000 {
>> + reg = <0x0 0x05000000 0x0 0x4000000>;
>> + no-map;
>> + };
>
> Please add a comment before the node explaining what needs this memory
>
Will add comment.
>> + };
>> };
>>
>> &uart_B {
>> @@ -34,3 +44,48 @@ &ir {
>> pinctrl-0 = <&remote_pins>;
>> pinctrl-names = "default";
>> };
>> +
>> +&nand {
>> + status = "okay";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + pinctrl-0 = <&nand_pins>;
>> + pinctrl-names = "default";
>> +
>> + nand@0 {
>> + reg = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + nand-on-flash-bbt;
>> +
>> + partition@0 {
>> + label = "boot";
>> + reg = <0x0 0x00200000>;
>> + };
>> + partition@200000 {
>> + label = "env";
>> + reg = <0x00200000 0x00400000>;
>> + };
>> + partition@600000 {
>> + label = "system";
>> + reg = <0x00600000 0x00a00000>;
>> + };
>> + partition@1000000 {
>> + label = "rootfs";
>> + reg = <0x01000000 0x03000000>;
>> + };
>> + partition@4000000 {
>> + label = "media";
>> + reg = <0x04000000 0x8000000>;
>> + };
>> + };
>> +};
>> +
>> +&spicc0 {
>> + status = "okay";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spicc0_pins_x>;
>> + cs-gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
>> +};
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
>> b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
>> index 2344b2d741c3..022aba0f9ef7 100644
>> --- a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
>> +++ b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
>> @@ -6,6 +6,10 @@
>> #include <dt-bindings/interrupt-controller/irq.h>
>> #include <dt-bindings/interrupt-controller/arm-gic.h>
>> #include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/gpio/meson-s4-gpio.h>
>> +#include <dt-bindings/clock/amlogic,s4-pll-clkc.h>
>> +#include <dt-bindings/clock/amlogic,s4-peripherals-clkc.h>
>> +#include <dt-bindings/power/meson-s4-power.h>
>>
>> / {
>> cpus {
>> @@ -92,6 +96,38 @@ apb4: bus@fe000000 {
>> #size-cells = <2>;
>> ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
>>
>> + clkc_periphs: clock-controller@0 {
>> + compatible = "amlogic,s4-peripherals-clkc";
>> + reg = <0x0 0x0 0x0 0x49c>;
>> + clocks = <&clkc_pll CLKID_FCLK_DIV2>,
>> + <&clkc_pll CLKID_FCLK_DIV2P5>,
>> + <&clkc_pll CLKID_FCLK_DIV3>,
>> + <&clkc_pll CLKID_FCLK_DIV4>,
>> + <&clkc_pll CLKID_FCLK_DIV5>,
>> + <&clkc_pll CLKID_FCLK_DIV7>,
>> + <&clkc_pll CLKID_HIFI_PLL>,
>> + <&clkc_pll CLKID_GP0_PLL>,
>> + <&clkc_pll CLKID_MPLL0>,
>> + <&clkc_pll CLKID_MPLL1>,
>> + <&clkc_pll CLKID_MPLL2>,
>> + <&clkc_pll CLKID_MPLL3>,
>> + <&clkc_pll CLKID_HDMI_PLL>,
>> + <&xtal>;
>> + clock-names = "fclk_div2",
>> "fclk_div2p5", "fclk_div3",
>> + "fclk_div4",
>> "fclk_div5", "fclk_div7",
>> + "hifi_pll", "gp0_pll",
>> "mpll0", "mpll1",
>> + "mpll2", "mpll3",
>> "hdmi_pll", "xtal";
>> + #clock-cells = <1>;
>> + };
>> +
>> + clkc_pll: clock-controller@8000 {
>> + compatible = "amlogic,s4-pll-clkc";
>> + reg = <0x0 0x8000 0x0 0x1e8>;
>> + clocks = <&xtal>;
>> + clock-names = "xtal";
>> + #clock-cells = <1>;
>> + };
>> +
>> watchdog@2100 {
>> compatible = "amlogic,s4-wdt",
>> "amlogic,t7-wdt";
>> reg = <0x0 0x2100 0x0 0x10>;
>> @@ -120,6 +156,187 @@ mux {
>> bias-disable;
>> };
>> };
>> +
>> + i2c0_pins1:i2c0-pins1 {
>
> Please add a space after ":"
>
Will do.
>> + mux {
>> + groups = "i2c0_sda",
>> + "i2c0_scl";
>> + function = "i2c0";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c1_pins1:i2c1-pins1 {
>
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c1_sda_c",
>> + "i2c1_scl_c";
>> + function = "i2c1";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c1_pins2:i2c1-pins2 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c1_sda_d",
>> + "i2c1_scl_d";
>> + function = "i2c1";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c1_pins3:i2c1-pins3 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c1_sda_h",
>> + "i2c1_scl_h";
>> + function = "i2c1";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c1_pins4:i2c1-pins4 {
> Ditto
>
>> + mux {
>> + groups = "i2c1_sda_x",
>> + "i2c1_scl_x";
>> + function = "i2c1";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c2_pins1:i2c2-pins1 {
>> + mux {
>> + groups = "i2c2_sda_d",
>> + "i2c2_scl_d";
>> + function = "i2c2";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c2_pins2:i2c2-pins2 {
>> + mux {
>> + groups = "i2c2_sda_h8",
>> + "i2c2_scl_h9";
>> + function = "i2c2";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c2_pins3:i2c2-pins3 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c2_sda_h0",
>> + "i2c2_scl_h1";
>> + function = "i2c2";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c3_pins1:i2c3-pins1 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c3_sda_x",
>> + "i2c3_scl_x";
>> + function = "i2c3";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c3_pins2:i2c3-pins2 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c3_sda_z",
>> + "i2c3_scl_z";
>> + function = "i2c3";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c4_pins1:i2c4-pins1 {
> Ditto
>
>> + mux {
>> + groups = "i2c4_sda_c",
>> + "i2c4_scl_c";
>> + function = "i2c4";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c4_pins2:i2c4-pins2 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c4_sda_d",
>> + "i2c4_scl_d";
>> + function = "i2c4";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + i2c4_pins3:i2c4-pins3 {
> Ditto
>
Will do.
>> + mux {
>> + groups = "i2c4_sda_z",
>> + "i2c4_scl_z";
>> + function = "i2c4";
>> + drive-strength-microamp
>> = <3000>;
>> + bias-disable;
>> + };
>> + };
>> +
>> + nand_pins: nand-pins {
>> + mux {
>> + groups = "emmc_nand_d0",
>> + "emmc_nand_d1",
>> + "emmc_nand_d2",
>> + "emmc_nand_d3",
>> + "emmc_nand_d4",
>> + "emmc_nand_d5",
>> + "emmc_nand_d6",
>> + "emmc_nand_d7",
>> + "nand_ce0",
>> + "nand_ale",
>> + "nand_cle",
>> + "nand_wen_clk",
>> + "nand_ren_wr";
>> + function = "nand";
>> + input-enable;
>> + };
>> + };
>> +
>> + spicc0_pins_x: spicc0-pins_x {
>> + mux {
>> + groups = "spi_a_mosi_x",
>> + "spi_a_miso_x",
>> + "spi_a_clk_x";
>> + function = "spi_a";
>> + drive-strength-microamp
>> = <3000>;
>> + };
>> + };
>> +
>> + spicc0_pins_h: spicc0-pins-h {
>> + mux {
>> + groups = "spi_a_mosi_h",
>> + "spi_a_miso_h",
>> + "spi_a_clk_h";
>> + function = "spi_a";
>> + drive-strength-microamp
>> = <3000>;
>> + };
>> + };
>> +
>> + spicc0_pins_z: spicc0-pins-z {
>> + mux {
>> + groups = "spi_a_mosi_z",
>> + "spi_a_miso_z",
>> + "spi_a_clk_z";
>> + function = "spi_a";
>> + drive-strength-microamp
>> = <3000>;
>> + };
>> + };
>> +
>> };
>>
>> gpio_intc: interrupt-controller@4080 {
>> @@ -132,13 +349,119 @@ gpio_intc: interrupt-controller@4080 {
>> <10 11 12 13 14 15 16 17 18 19
>> 20 21>;
>> };
>>
>> + eth_phy: mdio-multiplexer@28000 {
>> + compatible = "amlogic,g12a-mdio-mux";
>> + reg = <0x0 0x28000 0x0 0xa4>;
>> +
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&clkc_periphs CLKID_ETHPHY>,
>> + <&xtal>,
>> + <&clkc_pll CLKID_MPLL_50M>;
>> + clock-names = "pclk", "clkin0", "clkin1";
>> + mdio-parent-bus = <&mdio0>;
>> +
>> + ext_mdio: mdio@0 {
>> + reg = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + int_mdio: mdio@1 {
>> + reg = <1>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + internal_ephy: ethernet-phy@8 {
>> + compatible =
>> "ethernet-phy-id0180.3301",
>> +
>> "ethernet-phy-ieee802.3-c22";
>> + interrupts = <GIC_SPI 75
>> IRQ_TYPE_LEVEL_HIGH>;
>> + reg = <8>;
>> + max-speed = <100>;
>> + };
>> + };
>> + };
>> +
>> + spicc0: spi@50000 {
>> + compatible = "amlogic,meson-g12a-spicc";
>> + reg = <0x0 0x50000 0x0 0x44>;
>> + interrupts = <GIC_SPI 183
>> IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&clkc_periphs CLKID_SPICC0>,
>> + <&clkc_periphs CLKID_SPICC0_EN>;
>> + clock-names = "core", "pclk";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c@66000 {
>> + compatible = "amlogic,meson-axg-i2c";
>> + reg = <0x0 0x66000 0x0 0x20>;
>> + interrupts = <GIC_SPI 160
>> IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc_periphs CLKID_I2C_M_A>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c1: i2c@68000 {
>> + compatible = "amlogic,meson-axg-i2c";
>> + reg = <0x0 0x68000 0x0 0x20>;
>> + interrupts = <GIC_SPI 161
>> IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc_periphs CLKID_I2C_M_B>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c2: i2c@6a000 {
>> + compatible = "amlogic,meson-axg-i2c";
>> + reg = <0x0 0x6a000 0x0 0x20>;
>> + interrupts = <GIC_SPI 162
>> IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc_periphs CLKID_I2C_M_C>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c3: i2c@6c000 {
>> + compatible = "amlogic,meson-axg-i2c";
>> + reg = <0x0 0x6c000 0x0 0x20>;
>> + interrupts = <GIC_SPI 163
>> IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc_periphs CLKID_I2C_M_D>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c4: i2c@6e000 {
>> + compatible = "amlogic,meson-axg-i2c";
>> + reg = <0x0 0x6e000 0x0 0x20>;
>> + interrupts = <GIC_SPI 164
>> IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc_periphs CLKID_I2C_M_E>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + nand: nand-controller@8c800 {
>> + compatible = "amlogic,meson-axg-nfc";
>> + reg = <0x0 0x8c800 0x0 0x100>, <0x0
>> 0x8c000 0x0 0x4>;
>> + reg-names = "nfc", "emmc";
>> + interrupts = <GIC_SPI 175
>> IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc_periphs CLKID_SD_EMMC_C>,
>> + <&clkc_pll CLKID_FCLK_DIV2>;
>> + clock-names = "core", "device";
>> + status = "disabled";
>> + };
>> +
>> uart_B: serial@7a000 {
>> compatible = "amlogic,meson-s4-uart",
>> "amlogic,meson-ao-uart";
>> reg = <0x0 0x7a000 0x0 0x18>;
>> interrupts = <GIC_SPI 169
>> IRQ_TYPE_EDGE_RISING>;
>> status = "disabled";
>> - clocks = <&xtal>, <&xtal>, <&xtal>;
>> + clocks = <&xtal>, <&clkc_periphs
>> CLKID_UART_B>, <&xtal>;
>> clock-names = "xtal", "pclk", "baud";
>> };
>>
>> @@ -160,5 +483,30 @@ hwrng: rng@440788 {
>> reg = <0x0 0x440788 0x0 0x0c>;
>> };
>> };
>> +
>> + ethmac: ethernet@fdc00000 {
>> + compatible = "amlogic,meson-axg-dwmac",
>> + "snps,dwmac-3.70a",
>> + "snps,dwmac";
>> + reg = <0x0 0xfdc00000 0x0 0x10000>,
>> + <0x0 0xfe024000 0x0 0x8>;
>> +
>> + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "macirq";
>> + power-domains = <&pwrc PWRC_S4_ETH_ID>;
>> + clocks = <&clkc_periphs CLKID_ETH>,
>> + <&clkc_pll CLKID_FCLK_DIV2>,
>> + <&clkc_pll CLKID_MPLL2>;
>> + clock-names = "stmmaceth", "clkin0", "clkin1";
>> + rx-fifo-depth = <4096>;
>> + tx-fifo-depth = <2048>;
>> + status = "disabled";
>> +
>> + mdio0: mdio {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "snps,dwmac-mdio";
>> + };
>> + };
>> };
>> };
>>
>> base-commit: 3a5038e9c0556e51db96c2f7149d853efb886c95
>
> Thanks,
> Neil