2017-03-16 04:09:48

by Jane Li

[permalink] [raw]
Subject: [PATCH v2] net: mvneta: support suspend and resume

Add basic support for handling suspend and resume.

Signed-off-by: Jane Li <[email protected]>
---
Since v1:
- add mvneta_conf_mbus_windows() and mvneta_bm_port_init() in mvneta_resume()

drivers/net/ethernet/marvell/mvneta.c | 62 ++++++++++++++++++++++++++++++++---
1 file changed, 58 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 61dd446..250017b 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -431,6 +431,7 @@ struct mvneta_port {
/* Flags for special SoC configurations */
bool neta_armada3700;
u16 rx_offset_correction;
+ const struct mbus_dram_target_info *dram_target_info;
};

/* The mvneta_tx_desc and mvneta_rx_desc structures describe the
@@ -4118,7 +4119,6 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
/* Device initialization routine */
static int mvneta_probe(struct platform_device *pdev)
{
- const struct mbus_dram_target_info *dram_target_info;
struct resource *res;
struct device_node *dn = pdev->dev.of_node;
struct device_node *phy_node;
@@ -4267,13 +4267,13 @@ static int mvneta_probe(struct platform_device *pdev)

pp->tx_csum_limit = tx_csum_limit;

- dram_target_info = mv_mbus_dram_info();
+ pp->dram_target_info = mv_mbus_dram_info();
/* Armada3700 requires setting default configuration of Mbus
* windows, however without using filled mbus_dram_target_info
* structure.
*/
- if (dram_target_info || pp->neta_armada3700)
- mvneta_conf_mbus_windows(pp, dram_target_info);
+ if (pp->dram_target_info || pp->neta_armada3700)
+ mvneta_conf_mbus_windows(pp, pp->dram_target_info);

pp->tx_ring_size = MVNETA_MAX_TXD;
pp->rx_ring_size = MVNETA_MAX_RXD;
@@ -4405,6 +4405,59 @@ static int mvneta_remove(struct platform_device *pdev)
return 0;
}

+#ifdef CONFIG_PM_SLEEP
+static int mvneta_suspend(struct device *device)
+{
+ struct net_device *dev = dev_get_drvdata(device);
+ struct mvneta_port *pp = netdev_priv(dev);
+
+ if (netif_running(dev))
+ mvneta_stop(dev);
+ netif_device_detach(dev);
+ clk_disable_unprepare(pp->clk_bus);
+ clk_disable_unprepare(pp->clk);
+ return 0;
+}
+
+static int mvneta_resume(struct device *device)
+{
+ struct platform_device *pdev = to_platform_device(device);
+ struct net_device *dev = dev_get_drvdata(device);
+ struct mvneta_port *pp = netdev_priv(dev);
+ int err;
+
+ clk_prepare_enable(pp->clk);
+ clk_prepare_enable(pp->clk_bus);
+ if (pp->dram_target_info || pp->neta_armada3700)
+ mvneta_conf_mbus_windows(pp, pp->dram_target_info);
+ if (pp->bm_priv) {
+ err = mvneta_bm_port_init(pdev, pp);
+ if (err < 0) {
+ dev_info(&pdev->dev, "use SW buffer management\n");
+ pp->bm_priv = NULL;
+ }
+ }
+ mvneta_defaults_set(pp);
+ err = mvneta_port_power_up(pp, pp->phy_interface);
+ if (err < 0) {
+ dev_err(device, "can't power up port\n");
+ return err;
+ }
+
+ if (pp->use_inband_status)
+ mvneta_fixed_link_update(pp, dev->phydev);
+
+ netif_device_attach(dev);
+ if (netif_running(dev))
+ mvneta_open(dev);
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops mvneta_pm_ops = {
+ SET_LATE_SYSTEM_SLEEP_PM_OPS(mvneta_suspend, mvneta_resume)
+};
+
static const struct of_device_id mvneta_match[] = {
{ .compatible = "marvell,armada-370-neta" },
{ .compatible = "marvell,armada-xp-neta" },
@@ -4419,6 +4472,7 @@ static int mvneta_remove(struct platform_device *pdev)
.driver = {
.name = MVNETA_DRIVER_NAME,
.of_match_table = mvneta_match,
+ .pm = &mvneta_pm_ops,
},
};

--
1.9.1


2017-03-16 03:42:03

by Jisheng Zhang

[permalink] [raw]
Subject: Re: [PATCH v2] net: mvneta: support suspend and resume

On Thu, 16 Mar 2017 11:19:10 +0800 Jane Li wrote:

> Add basic support for handling suspend and resume.
>
> Signed-off-by: Jane Li <[email protected]>
> ---
> Since v1:
> - add mvneta_conf_mbus_windows() and mvneta_bm_port_init() in mvneta_resume()
>
> drivers/net/ethernet/marvell/mvneta.c | 62 ++++++++++++++++++++++++++++++++---
> 1 file changed, 58 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
> index 61dd446..250017b 100644
> --- a/drivers/net/ethernet/marvell/mvneta.c
> +++ b/drivers/net/ethernet/marvell/mvneta.c
> @@ -431,6 +431,7 @@ struct mvneta_port {
> /* Flags for special SoC configurations */
> bool neta_armada3700;
> u16 rx_offset_correction;
> + const struct mbus_dram_target_info *dram_target_info;
> };
>
> /* The mvneta_tx_desc and mvneta_rx_desc structures describe the
> @@ -4118,7 +4119,6 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
> /* Device initialization routine */
> static int mvneta_probe(struct platform_device *pdev)
> {
> - const struct mbus_dram_target_info *dram_target_info;
> struct resource *res;
> struct device_node *dn = pdev->dev.of_node;
> struct device_node *phy_node;
> @@ -4267,13 +4267,13 @@ static int mvneta_probe(struct platform_device *pdev)
>
> pp->tx_csum_limit = tx_csum_limit;
>
> - dram_target_info = mv_mbus_dram_info();
> + pp->dram_target_info = mv_mbus_dram_info();
> /* Armada3700 requires setting default configuration of Mbus
> * windows, however without using filled mbus_dram_target_info
> * structure.
> */
> - if (dram_target_info || pp->neta_armada3700)
> - mvneta_conf_mbus_windows(pp, dram_target_info);
> + if (pp->dram_target_info || pp->neta_armada3700)
> + mvneta_conf_mbus_windows(pp, pp->dram_target_info);
>
> pp->tx_ring_size = MVNETA_MAX_TXD;
> pp->rx_ring_size = MVNETA_MAX_RXD;
> @@ -4405,6 +4405,59 @@ static int mvneta_remove(struct platform_device *pdev)
> return 0;
> }
>
> +#ifdef CONFIG_PM_SLEEP
> +static int mvneta_suspend(struct device *device)
> +{
> + struct net_device *dev = dev_get_drvdata(device);
> + struct mvneta_port *pp = netdev_priv(dev);
> +
> + if (netif_running(dev))
> + mvneta_stop(dev);
> + netif_device_detach(dev);
> + clk_disable_unprepare(pp->clk_bus);
> + clk_disable_unprepare(pp->clk);
> + return 0;
> +}
> +
> +static int mvneta_resume(struct device *device)
> +{
> + struct platform_device *pdev = to_platform_device(device);
> + struct net_device *dev = dev_get_drvdata(device);
> + struct mvneta_port *pp = netdev_priv(dev);
> + int err;
> +
> + clk_prepare_enable(pp->clk);
> + clk_prepare_enable(pp->clk_bus);
> + if (pp->dram_target_info || pp->neta_armada3700)
> + mvneta_conf_mbus_windows(pp, pp->dram_target_info);
> + if (pp->bm_priv) {
> + err = mvneta_bm_port_init(pdev, pp);
> + if (err < 0) {
> + dev_info(&pdev->dev, "use SW buffer management\n");
> + pp->bm_priv = NULL;
> + }
> + }
> + mvneta_defaults_set(pp);
> + err = mvneta_port_power_up(pp, pp->phy_interface);
> + if (err < 0) {
> + dev_err(device, "can't power up port\n");
> + return err;
> + }
> +
> + if (pp->use_inband_status)
> + mvneta_fixed_link_update(pp, dev->phydev);
> +
> + netif_device_attach(dev);
> + if (netif_running(dev))
> + mvneta_open(dev);
> + return 0;
> +}
> +#endif
> +
> +static const struct dev_pm_ops mvneta_pm_ops = {
> + SET_LATE_SYSTEM_SLEEP_PM_OPS(mvneta_suspend, mvneta_resume)
> +};

we could make use of SIMPLE_DEV_PM_OPS to simplify the code

Thanks

2017-03-16 07:41:43

by Jane Li

[permalink] [raw]
Subject: Re: [PATCH v2] net: mvneta: support suspend and resume



On 03/16/2017 11:37 AM, Jisheng Zhang wrote:
> On Thu, 16 Mar 2017 11:19:10 +0800 Jane Li wrote:
>
>> Add basic support for handling suspend and resume.
>>
>> Signed-off-by: Jane Li <[email protected]>
>> ---
>> Since v1:
>> - add mvneta_conf_mbus_windows() and mvneta_bm_port_init() in mvneta_resume()
>>
>> drivers/net/ethernet/marvell/mvneta.c | 62 ++++++++++++++++++++++++++++++++---
>> 1 file changed, 58 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
>> index 61dd446..250017b 100644
>> --- a/drivers/net/ethernet/marvell/mvneta.c
>> +++ b/drivers/net/ethernet/marvell/mvneta.c
>> @@ -431,6 +431,7 @@ struct mvneta_port {
>> /* Flags for special SoC configurations */
>> bool neta_armada3700;
>> u16 rx_offset_correction;
>> + const struct mbus_dram_target_info *dram_target_info;
>> };
>>
>> /* The mvneta_tx_desc and mvneta_rx_desc structures describe the
>> @@ -4118,7 +4119,6 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
>> /* Device initialization routine */
>> static int mvneta_probe(struct platform_device *pdev)
>> {
>> - const struct mbus_dram_target_info *dram_target_info;
>> struct resource *res;
>> struct device_node *dn = pdev->dev.of_node;
>> struct device_node *phy_node;
>> @@ -4267,13 +4267,13 @@ static int mvneta_probe(struct platform_device *pdev)
>>
>> pp->tx_csum_limit = tx_csum_limit;
>>
>> - dram_target_info = mv_mbus_dram_info();
>> + pp->dram_target_info = mv_mbus_dram_info();
>> /* Armada3700 requires setting default configuration of Mbus
>> * windows, however without using filled mbus_dram_target_info
>> * structure.
>> */
>> - if (dram_target_info || pp->neta_armada3700)
>> - mvneta_conf_mbus_windows(pp, dram_target_info);
>> + if (pp->dram_target_info || pp->neta_armada3700)
>> + mvneta_conf_mbus_windows(pp, pp->dram_target_info);
>>
>> pp->tx_ring_size = MVNETA_MAX_TXD;
>> pp->rx_ring_size = MVNETA_MAX_RXD;
>> @@ -4405,6 +4405,59 @@ static int mvneta_remove(struct platform_device *pdev)
>> return 0;
>> }
>>
>> +#ifdef CONFIG_PM_SLEEP
>> +static int mvneta_suspend(struct device *device)
>> +{
>> + struct net_device *dev = dev_get_drvdata(device);
>> + struct mvneta_port *pp = netdev_priv(dev);
>> +
>> + if (netif_running(dev))
>> + mvneta_stop(dev);
>> + netif_device_detach(dev);
>> + clk_disable_unprepare(pp->clk_bus);
>> + clk_disable_unprepare(pp->clk);
>> + return 0;
>> +}
>> +
>> +static int mvneta_resume(struct device *device)
>> +{
>> + struct platform_device *pdev = to_platform_device(device);
>> + struct net_device *dev = dev_get_drvdata(device);
>> + struct mvneta_port *pp = netdev_priv(dev);
>> + int err;
>> +
>> + clk_prepare_enable(pp->clk);
>> + clk_prepare_enable(pp->clk_bus);
>> + if (pp->dram_target_info || pp->neta_armada3700)
>> + mvneta_conf_mbus_windows(pp, pp->dram_target_info);
>> + if (pp->bm_priv) {
>> + err = mvneta_bm_port_init(pdev, pp);
>> + if (err < 0) {
>> + dev_info(&pdev->dev, "use SW buffer management\n");
>> + pp->bm_priv = NULL;
>> + }
>> + }
>> + mvneta_defaults_set(pp);
>> + err = mvneta_port_power_up(pp, pp->phy_interface);
>> + if (err < 0) {
>> + dev_err(device, "can't power up port\n");
>> + return err;
>> + }
>> +
>> + if (pp->use_inband_status)
>> + mvneta_fixed_link_update(pp, dev->phydev);
>> +
>> + netif_device_attach(dev);
>> + if (netif_running(dev))
>> + mvneta_open(dev);
>> + return 0;
>> +}
>> +#endif
>> +
>> +static const struct dev_pm_ops mvneta_pm_ops = {
>> + SET_LATE_SYSTEM_SLEEP_PM_OPS(mvneta_suspend, mvneta_resume)
>> +};
> we could make use of SIMPLE_DEV_PM_OPS to simplify the code
>
> Thanks
Done. Modify this in patch v3.

Thanks,
Jane