File st,i2c.yaml replaces i2c-st.txt for the i2c-st driver.
Signed-off-by: Alain Volmat <[email protected]>
---
.../devicetree/bindings/i2c/i2c-st.txt | 41 -----------
.../devicetree/bindings/i2c/st,sti-i2c.yaml | 72 +++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 73 insertions(+), 42 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-st.txt
create mode 100644 Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt
deleted file mode 100644
index 4c26fda3844a..000000000000
--- a/Documentation/devicetree/bindings/i2c/i2c-st.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-ST SSC binding, for I2C mode operation
-
-Required properties :
-- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c"
-- reg : Offset and length of the register set for the device
-- interrupts : the interrupt specifier
-- clock-names: Must contain "ssc".
-- clocks: Must contain an entry for each name in clock-names. See the common
- clock bindings.
-- A pinctrl state named "default" must be defined to set pins in mode of
- operation for I2C transfer.
-
-Optional properties :
-- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
- the default 100 kHz frequency will be used. As only Normal and Fast modes
- are supported, possible values are 100000 and 400000.
-- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is
- allowed through the deglitch circuit. In units of us.
-- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is
- allowed through the deglitch circuit. In units of us.
-- A pinctrl state named "idle" could be defined to set pins in idle state
- when I2C instance is not performing a transfer.
-- A pinctrl state named "sleep" could be defined to set pins in sleep state
- when driver enters in suspend.
-
-
-
-Example :
-
-i2c0: i2c@fed40000 {
- compatible = "st,comms-ssc4-i2c";
- reg = <0xfed40000 0x110>;
- interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk_s_a0_ls CLK_ICN_REG>;
- clock-names = "ssc";
- clock-frequency = <400000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c0_default>;
- st,i2c-min-scl-pulse-width-us = <0>;
- st,i2c-min-sda-pulse-width-us = <5>;
-};
diff --git a/Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml b/Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
new file mode 100644
index 000000000000..dd6ff18b9ed7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/st,sti-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: I2C controller embedded in STMicroelectronics STi platform
+
+maintainers:
+ - Patrice Chotard <[email protected]>
+
+allOf:
+ - $ref: /schemas/i2c/i2c-controller.yaml#
+
+properties:
+ compatible:
+ enum:
+ - st,comms-ssc-i2c
+ - st,comms-ssc4-i2c
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ maxItems: 1
+
+ clock-frequency:
+ enum: [ 100000, 400000 ]
+
+ st,i2c-min-scl-pulse-width-us:
+ description:
+ The minimum valid SCL pulse width that is allowed through the
+ deglitch circuit. In units of us.
+ maxItems: 1
+
+ st,i2c-min-sda-pulse-width-us:
+ description:
+ The minimum valid SDA pulse width that is allowed through the
+ deglitch circuit. In units of us.
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/stih407-clks.h>
+ i2c@fed40000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfed40000 0x110>;
+ interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk_s_a0_ls CLK_ICN_REG>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ st,i2c-min-scl-pulse-width-us = <0>;
+ st,i2c-min-sda-pulse-width-us = <5>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 06d5be2c713c..2e32eb8d44f5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2925,7 +2925,7 @@ M: Patrice Chotard <[email protected]>
L: [email protected] (moderated for non-subscribers)
S: Maintained
W: http://www.stlinux.com
-F: Documentation/devicetree/bindings/i2c/i2c-st.txt
+F: Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
F: arch/arm/boot/dts/sti*
F: arch/arm/mach-sti/
F: drivers/ata/ahci_st.c
--
2.34.1
On 10/02/2023 11:12, Alain Volmat wrote:
> File st,i2c.yaml replaces i2c-st.txt for the i2c-st driver.
Subject: dt-bindings: i2c: st,sti-i2c: convert to DT schema
(same reasoning as for SPI patch and maybe others)
>
> Signed-off-by: Alain Volmat <[email protected]>
> ---
> .../devicetree/bindings/i2c/i2c-st.txt | 41 -----------
> .../devicetree/bindings/i2c/st,sti-i2c.yaml | 72 +++++++++++++++++++
> MAINTAINERS | 2 +-
> 3 files changed, 73 insertions(+), 42 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-st.txt
> create mode 100644 Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
>
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt
> deleted file mode 100644
> index 4c26fda3844a..000000000000
> --- a/Documentation/devicetree/bindings/i2c/i2c-st.txt
> +++ /dev/null
> @@ -1,41 +0,0 @@
> -ST SSC binding, for I2C mode operation
> -
> -Required properties :
> -- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c"
> -- reg : Offset and length of the register set for the device
> -- interrupts : the interrupt specifier
> -- clock-names: Must contain "ssc".
> -- clocks: Must contain an entry for each name in clock-names. See the common
> - clock bindings.
> -- A pinctrl state named "default" must be defined to set pins in mode of
> - operation for I2C transfer.
> -
> -Optional properties :
> -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
> - the default 100 kHz frequency will be used. As only Normal and Fast modes
> - are supported, possible values are 100000 and 400000.
> -- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is
> - allowed through the deglitch circuit. In units of us.
> -- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is
> - allowed through the deglitch circuit. In units of us.
> -- A pinctrl state named "idle" could be defined to set pins in idle state
> - when I2C instance is not performing a transfer.
> -- A pinctrl state named "sleep" could be defined to set pins in sleep state
> - when driver enters in suspend.
> -
> -
> -
> -Example :
> -
> -i2c0: i2c@fed40000 {
> - compatible = "st,comms-ssc4-i2c";
> - reg = <0xfed40000 0x110>;
> - interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk_s_a0_ls CLK_ICN_REG>;
> - clock-names = "ssc";
> - clock-frequency = <400000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c0_default>;
> - st,i2c-min-scl-pulse-width-us = <0>;
> - st,i2c-min-sda-pulse-width-us = <5>;
> -};
> diff --git a/Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml b/Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
> new file mode 100644
> index 000000000000..dd6ff18b9ed7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/st,sti-i2c.yaml
> @@ -0,0 +1,72 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/i2c/st,sti-i2c.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: I2C controller embedded in STMicroelectronics STi platform
> +
> +maintainers:
> + - Patrice Chotard <[email protected]>
> +
> +allOf:
> + - $ref: /schemas/i2c/i2c-controller.yaml#
> +
> +properties:
> + compatible:
> + enum:
> + - st,comms-ssc-i2c
> + - st,comms-ssc4-i2c
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + maxItems: 1
> +
> + clock-frequency:
> + enum: [ 100000, 400000 ]
default: 100000
> +
> + st,i2c-min-scl-pulse-width-us:
> + description:
> + The minimum valid SCL pulse width that is allowed through the
> + deglitch circuit. In units of us.
> + maxItems: 1
maxItems should not be needed.
> +
> + st,i2c-min-sda-pulse-width-us:
> + description:
> + The minimum valid SDA pulse width that is allowed through the
> + deglitch circuit. In units of us.
> + maxItems: 1
Ditto
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - clocks
> + - clock-names
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/stih407-clks.h>
> + i2c@fed40000 {
> + compatible = "st,comms-ssc4-i2c";
Drop unnecessary spaces before =
Best regards,
Krzysztof