Changes in v12:
1. add a new patch "stmmac: dwmac-mediatek: re-arrange clock setting" to
this series, to simplify clock handling in driver, which benefits to
binding file mediatek-dwmac.yaml.
2. modify dt-binding description in patch "net: dt-bindings: dwmac: add
support for mt8195" as Rob's comments in v10 series, put mac_cg to the
end of clock list.
3. there are small changes in patch "stmmac: dwmac-mediatek: add support
for mt8195", @AngeloGioacchino, please review it kindly.
Changes in v11:
1. add reivewed-by in "net: dt-bindings: dwmac: Convert mediatek-dwmac to
DT schema" as Rob's comments.
2. fall back "net: dt-bindings: dwmac: add support for mt8195" to v8 version
as mentioned in previous reply(https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/):
2.1 there is already a special clock named "rmii_internal", which need to
be put to the end of the clock list(driver special handling),
so we can't simply put new "mac_cg" for mt8195 to the end of the clock
list.
2.2 we prefer the if-then schema, which will make mt8195 clock list clearer
with some duplicated information.
2.3 we expect the future IC will follow mt2712 or mt8195, so we only need
add new IC name to compatible list for future IC, and will not make the
clock list binding files worse.
Changes in v10:
1. add detailed description in "arm64: dts: mt2712: update ethernet
device node" to make the modifications clearer as Matthias's comments.
2. modify dt-binding description as Rob's comments, and "make dtbs_check" runs
pass locally with "arm64: dts: mt2712: update ethernet device node"
in this series.
Changes in v9:
1. remove oneOf for 1 entry as Rob's comments.
2. add new clocks to the end of existing clocks to simplify
the binding as Rob's comments.
Changes in v8:
1. add acked-by in "stmmac: dwmac-mediatek: add platform level clocks
management" patch
Changes in v7:
1. fix uninitialized warning as Jakub's comments.
Changes in v6:
1. update commit message as Jakub's comments.
2. split mt8195 eth dts patch("arm64: dts: mt8195: add ethernet device
node") from this series, since mt8195 dtsi/dts basic patches is still
under reviewing.
https://patchwork.kernel.org/project/linux-mediatek/list/?series=579071
we'll resend mt8195 eth dts patch once all the dependent patches are
accepted.
Changes in v5:
1. remove useless inclusion in dwmac-mediatek.c as Angelo's comments.
2. add acked-by in "net-next: stmmac: dwmac-mediatek: add support for
mt8195" patch
Changes in v4:
1. add changes in commit message in "net-next: dt-bindings: dwmac:
Convert mediatek-dwmac to DT schema" patch.
2. remove ethernet-controller.yaml since snps,dwmac.yaml already include it.
Changes in v3:
1. Add prefix "net-next" to support new IC as Denis's suggestion.
2. Split dt-bindings to two patches, one for conversion, and the other for
new IC.
3. add a new patch to update device node in mt2712-evb.dts to accommodate to
changes in driver.
4. remove unnecessary wrapper as Angelo's suggestion.
5. Add acked-by in "net-next: stmmac: dwmac-mediatek: Reuse more common
features" patch.
Changes in v2:
1. fix errors/warnings in mediatek-dwmac.yaml with upgraded dtschema tools
Changes in v1:
This series include 5 patches:
1. add platform level clocks management for dwmac-mediatek
2. resue more common features defined in stmmac_platform.c
3. add ethernet entry for mt8195
Biao Huang (7):
stmmac: dwmac-mediatek: add platform level clocks management
stmmac: dwmac-mediatek: Reuse more common features
stmmac: dwmac-mediatek: re-arrange clock setting
arm64: dts: mt2712: update ethernet device node
net: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
stmmac: dwmac-mediatek: add support for mt8195
net: dt-bindings: dwmac: add support for mt8195
.../bindings/net/mediatek-dwmac.txt | 91 ----
.../bindings/net/mediatek-dwmac.yaml | 175 ++++++++
arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 +
arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +-
.../ethernet/stmicro/stmmac/dwmac-mediatek.c | 389 +++++++++++++++---
5 files changed, 526 insertions(+), 144 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt
create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
--
2.18.0
Since there are some changes in ethernet driver:
update ethernet device node in dts to accommodate to it.
1. stmmac_probe_config_dt() in stmmac_platform.c will initialize specified
parameters according to compatible string "snps,dwmac-4.20a", then,
dwmac-mediatek.c can skip the initialization if add compatible string
"snps,dwmac-4.20a" in eth device node.
2. commit 882007ed7832 ("net-next: dt-binding: dwmac-mediatek: add more
description for RMII") added rmii internal support, we should add
corresponding clocks/clocks-names in eth device node.
3. add "snps,reset-delays-us = <0 10000 10000>;" to ensure reset delay
can meet PHY requirement.
Signed-off-by: Biao Huang <[email protected]>
---
arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 +
arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++-----
2 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
index 7d369fdd3117..11aa135aa0f3 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
@@ -110,6 +110,7 @@ ð {
phy-handle = <ðernet_phy0>;
mediatek,tx-delay-ps = <1530>;
snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+ snps,reset-delays-us = <0 10000 10000>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <ð_default>;
pinctrl-1 = <ð_sleep>;
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index a9cca9c146fd..9e850e04fffb 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -726,7 +726,7 @@ queue2 {
};
eth: ethernet@1101c000 {
- compatible = "mediatek,mt2712-gmac";
+ compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
reg = <0 0x1101c000 0 0x1300>;
interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
interrupt-names = "macirq";
@@ -734,15 +734,19 @@ eth: ethernet@1101c000 {
clock-names = "axi",
"apb",
"mac_main",
- "ptp_ref";
+ "ptp_ref",
+ "rmii_internal";
clocks = <&pericfg CLK_PERI_GMAC>,
<&pericfg CLK_PERI_GMAC_PCLK>,
<&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>;
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>;
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
- <&topckgen CLK_TOP_APLL1_D3>;
+ <&topckgen CLK_TOP_APLL1_D3>,
+ <&topckgen CLK_TOP_ETHERPLL_50M>;
power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
mediatek,pericfg = <&pericfg>;
snps,axi-config = <&stmmac_axi_setup>;
--
2.25.1
Add binding document for the ethernet on mt8195.
Signed-off-by: Biao Huang <[email protected]>
---
.../bindings/net/mediatek-dwmac.yaml | 28 ++++++++++++++++---
1 file changed, 24 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
index 8ad6e19661b8..901944683322 100644
--- a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
@@ -19,6 +19,7 @@ select:
contains:
enum:
- mediatek,mt2712-gmac
+ - mediatek,mt8195-gmac
required:
- compatible
@@ -27,26 +28,35 @@ allOf:
properties:
compatible:
- items:
- - enum:
- - mediatek,mt2712-gmac
- - const: snps,dwmac-4.20a
+ oneOf:
+ - items:
+ - enum:
+ - mediatek,mt2712-gmac
+ - const: snps,dwmac-4.20a
+ - items:
+ - enum:
+ - mediatek,mt8195-gmac
+ - const: snps,dwmac-5.10a
clocks:
+ minItems: 5
items:
- description: AXI clock
- description: APB clock
- description: MAC Main clock
- description: PTP clock
- description: RMII reference clock provided by MAC
+ - description: MAC clock gate
clock-names:
+ minItems: 5
items:
- const: axi
- const: apb
- const: mac_main
- const: ptp_ref
- const: rmii_internal
+ - const: mac_cg
mediatek,pericfg:
$ref: /schemas/types.yaml#/definitions/phandle
@@ -61,6 +71,8 @@ properties:
or will round down. Range 0~31*170.
For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
or will round down. Range 0~31*550.
+ For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290,
+ or will round down. Range 0~31*290.
mediatek,rx-delay-ps:
description:
@@ -69,6 +81,8 @@ properties:
or will round down. Range 0~31*170.
For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
or will round down. Range 0~31*550.
+ For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple
+ of 290, or will round down. Range 0~31*290.
mediatek,rmii-rxc:
type: boolean
@@ -102,6 +116,12 @@ properties:
3. the inside clock, which be sent to MAC, will be inversed in RMII case when
the reference clock is from MAC.
+ mediatek,mac-wol:
+ type: boolean
+ description:
+ If present, indicates that MAC supports WOL(Wake-On-LAN), and MAC WOL will be enabled.
+ Otherwise, PHY WOL is perferred.
+
required:
- compatible
- reg
--
2.25.1
Add Ethernet support for MediaTek SoCs from the mt8195 family.
Signed-off-by: Biao Huang <[email protected]>
Acked-by: AngeloGioacchino Del Regno <[email protected]>
---
.../ethernet/stmicro/stmmac/dwmac-mediatek.c | 278 +++++++++++++++++-
1 file changed, 268 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index 2678d2deb26a..3b12434fdb24 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -39,6 +39,33 @@
#define ETH_FINE_DLY_GTXC BIT(1)
#define ETH_FINE_DLY_RXC BIT(0)
+/* Peri Configuration register for mt8195 */
+#define MT8195_PERI_ETH_CTRL0 0xFD0
+#define MT8195_RMII_CLK_SRC_INTERNAL BIT(28)
+#define MT8195_RMII_CLK_SRC_RXC BIT(27)
+#define MT8195_ETH_INTF_SEL GENMASK(26, 24)
+#define MT8195_RGMII_TXC_PHASE_CTRL BIT(22)
+#define MT8195_EXT_PHY_MODE BIT(21)
+#define MT8195_DLY_GTXC_INV BIT(12)
+#define MT8195_DLY_GTXC_ENABLE BIT(5)
+#define MT8195_DLY_GTXC_STAGES GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL1 0xFD4
+#define MT8195_DLY_RXC_INV BIT(25)
+#define MT8195_DLY_RXC_ENABLE BIT(18)
+#define MT8195_DLY_RXC_STAGES GENMASK(17, 13)
+#define MT8195_DLY_TXC_INV BIT(12)
+#define MT8195_DLY_TXC_ENABLE BIT(5)
+#define MT8195_DLY_TXC_STAGES GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL2 0xFD8
+#define MT8195_DLY_RMII_RXC_INV BIT(25)
+#define MT8195_DLY_RMII_RXC_ENABLE BIT(18)
+#define MT8195_DLY_RMII_RXC_STAGES GENMASK(17, 13)
+#define MT8195_DLY_RMII_TXC_INV BIT(12)
+#define MT8195_DLY_RMII_TXC_ENABLE BIT(5)
+#define MT8195_DLY_RMII_TXC_STAGES GENMASK(4, 0)
+
struct mac_delay_struct {
u32 tx_delay;
u32 rx_delay;
@@ -57,12 +84,14 @@ struct mediatek_dwmac_plat_data {
phy_interface_t phy_mode;
bool rmii_clk_from_mac;
bool rmii_rxc;
+ bool mac_wol;
int num_clks;
};
struct mediatek_dwmac_variant {
int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);
int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
+ void (*dwmac_fix_mac_speed)(void *priv, unsigned int speed);
/* clock ids to be requested */
const char * const *clk_list;
@@ -78,6 +107,10 @@ static const char * const mt2712_dwmac_clk_l[] = {
"axi", "apb", "mac_main", "ptp_ref"
};
+static const char * const mt8195_dwmac_clk_l[] = {
+ "axi", "apb", "mac_cg", "mac_main", "ptp_ref"
+};
+
static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
{
int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0;
@@ -257,6 +290,193 @@ static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
.tx_delay_max = 17600,
};
+static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat)
+{
+ int rmii_clk_from_mac = plat->rmii_clk_from_mac ? MT8195_RMII_CLK_SRC_INTERNAL : 0;
+ int rmii_rxc = plat->rmii_rxc ? MT8195_RMII_CLK_SRC_RXC : 0;
+ u32 intf_val = 0;
+
+ /* select phy interface in top control domain */
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_MII);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ intf_val |= (rmii_rxc | rmii_clk_from_mac);
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RMII);
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RGMII);
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ /* MT8195 only support external PHY */
+ intf_val |= MT8195_EXT_PHY_MODE;
+
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL0, intf_val);
+
+ return 0;
+}
+
+static void mt8195_delay_ps2stage(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+ /* 290ps per stage */
+ mac_delay->tx_delay /= 290;
+ mac_delay->rx_delay /= 290;
+}
+
+static void mt8195_delay_stage2ps(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+ /* 290ps per stage */
+ mac_delay->tx_delay *= 290;
+ mac_delay->rx_delay *= 290;
+}
+
+static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+ u32 gtxc_delay_val = 0, delay_val = 0, rmii_delay_val = 0;
+
+ mt8195_delay_ps2stage(plat);
+
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ if (plat->rmii_clk_from_mac) {
+ /* case 1: mac provides the rmii reference clock,
+ * and the clock output to TXC pin.
+ * The egress timing can be adjusted by RMII_TXC delay macro circuit.
+ * The ingress timing can be adjusted by RMII_RXC delay macro circuit.
+ */
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_ENABLE,
+ !!mac_delay->tx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_STAGES,
+ mac_delay->tx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_INV,
+ mac_delay->tx_inv);
+
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_ENABLE,
+ !!mac_delay->rx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_STAGES,
+ mac_delay->rx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_INV,
+ mac_delay->rx_inv);
+ } else {
+ /* case 2: the rmii reference clock is from external phy,
+ * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+ * the reference clk is connected to. The reference clock is a
+ * received signal, so rx_delay/rx_inv are used to indicate
+ * the reference clock timing adjustment
+ */
+ if (plat->rmii_rxc) {
+ /* the rmii reference clock from outside is connected
+ * to RXC pin, the reference clock will be adjusted
+ * by RXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE,
+ !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES,
+ mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV,
+ mac_delay->rx_inv);
+ } else {
+ /* the rmii reference clock from outside is connected
+ * to TXC pin, the reference clock will be adjusted
+ * by TXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE,
+ !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES,
+ mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV,
+ mac_delay->rx_inv);
+ }
+ }
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_STAGES, mac_delay->tx_delay);
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(plat->peri_regmap,
+ MT8195_PERI_ETH_CTRL0,
+ MT8195_RGMII_TXC_PHASE_CTRL |
+ MT8195_DLY_GTXC_INV |
+ MT8195_DLY_GTXC_ENABLE |
+ MT8195_DLY_GTXC_STAGES,
+ gtxc_delay_val);
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL1, delay_val);
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL2, rmii_delay_val);
+
+ mt8195_delay_stage2ps(plat);
+
+ return 0;
+}
+
+static void mt8195_fix_mac_speed(void *priv, unsigned int speed)
+{
+ struct mediatek_dwmac_plat_data *priv_plat = priv;
+
+ if ((phy_interface_mode_is_rgmii(priv_plat->phy_mode))) {
+ /* prefer 2ns fixed delay which is controlled by TXC_PHASE_CTRL,
+ * when link speed is 1Gbps with RGMII interface,
+ * Fall back to delay macro circuit for 10/100Mbps link speed.
+ */
+ if (speed == SPEED_1000)
+ regmap_update_bits(priv_plat->peri_regmap,
+ MT8195_PERI_ETH_CTRL0,
+ MT8195_RGMII_TXC_PHASE_CTRL |
+ MT8195_DLY_GTXC_ENABLE |
+ MT8195_DLY_GTXC_INV |
+ MT8195_DLY_GTXC_STAGES,
+ MT8195_RGMII_TXC_PHASE_CTRL);
+ else
+ mt8195_set_delay(priv_plat);
+ }
+}
+
+static const struct mediatek_dwmac_variant mt8195_gmac_variant = {
+ .dwmac_set_phy_interface = mt8195_set_interface,
+ .dwmac_set_delay = mt8195_set_delay,
+ .dwmac_fix_mac_speed = mt8195_fix_mac_speed,
+ .clk_list = mt8195_dwmac_clk_l,
+ .num_clks = ARRAY_SIZE(mt8195_dwmac_clk_l),
+ .dma_bit_mask = 35,
+ .rx_delay_max = 9280,
+ .tx_delay_max = 9280,
+};
+
static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
{
struct mac_delay_struct *mac_delay = &plat->mac_delay;
@@ -297,6 +517,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac");
+ plat->mac_wol = of_property_read_bool(plat->np, "mediatek,mac-wol");
return 0;
}
@@ -409,6 +630,50 @@ static int mediatek_dwmac_clks_config(void *priv, bool enabled)
return ret;
}
+
+static int mediatek_dwmac_common_data(struct platform_device *pdev,
+ struct plat_stmmacenet_data *plat,
+ struct mediatek_dwmac_plat_data *priv_plat)
+{
+ int i;
+
+ plat->interface = priv_plat->phy_mode;
+ plat->use_phy_wol = priv_plat->mac_wol ? 0 : 1;
+ plat->riwt_off = 1;
+ plat->maxmtu = ETH_DATA_LEN;
+ plat->addr64 = priv_plat->variant->dma_bit_mask;
+ plat->bsp_priv = priv_plat;
+ plat->init = mediatek_dwmac_init;
+ plat->exit = mediatek_dwmac_exit;
+ plat->clks_config = mediatek_dwmac_clks_config;
+ if (priv_plat->variant->dwmac_fix_mac_speed)
+ plat->fix_mac_speed = priv_plat->variant->dwmac_fix_mac_speed;
+
+ plat->safety_feat_cfg = devm_kzalloc(&pdev->dev,
+ sizeof(*plat->safety_feat_cfg),
+ GFP_KERNEL);
+ if (!plat->safety_feat_cfg)
+ return -ENOMEM;
+
+ plat->safety_feat_cfg->tsoee = 1;
+ plat->safety_feat_cfg->mrxpee = 0;
+ plat->safety_feat_cfg->mestee = 1;
+ plat->safety_feat_cfg->mrxee = 1;
+ plat->safety_feat_cfg->mtxee = 1;
+ plat->safety_feat_cfg->epsi = 0;
+ plat->safety_feat_cfg->edpp = 1;
+ plat->safety_feat_cfg->prtyen = 1;
+ plat->safety_feat_cfg->tmouten = 1;
+
+ for (i = 0; i < plat->tx_queues_to_use; i++) {
+ /* Default TX Q0 to use TSO and rest TXQ for TBS */
+ if (i > 0)
+ plat->tx_queues_cfg[i].tbs_en = 1;
+ }
+
+ return 0;
+}
+
static int mediatek_dwmac_probe(struct platform_device *pdev)
{
struct mediatek_dwmac_plat_data *priv_plat;
@@ -445,16 +710,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
if (IS_ERR(plat_dat))
return PTR_ERR(plat_dat);
- plat_dat->interface = priv_plat->phy_mode;
- plat_dat->use_phy_wol = 1;
- plat_dat->riwt_off = 1;
- plat_dat->maxmtu = ETH_DATA_LEN;
- plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
- plat_dat->bsp_priv = priv_plat;
- plat_dat->init = mediatek_dwmac_init;
- plat_dat->exit = mediatek_dwmac_exit;
- plat_dat->clks_config = mediatek_dwmac_clks_config;
-
+ mediatek_dwmac_common_data(pdev, plat_dat, priv_plat);
mediatek_dwmac_init(pdev, priv_plat);
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
@@ -469,6 +725,8 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
static const struct of_device_id mediatek_dwmac_match[] = {
{ .compatible = "mediatek,mt2712-gmac",
.data = &mt2712_gmac_variant },
+ { .compatible = "mediatek,mt8195-gmac",
+ .data = &mt8195_gmac_variant },
{ }
};
--
2.25.1
Convert mediatek-dwmac to DT schema, and delete old mediatek-dwmac.txt.
And there are some changes in .yaml than .txt, others almost keep the same:
1. compatible "const: snps,dwmac-4.20".
2. delete "snps,reset-active-low;" in example, since driver remove this
property long ago.
3. add "snps,reset-delay-us = <0 10000 10000>" in example.
4. the example is for rgmii interface, keep related properties only.
Signed-off-by: Biao Huang <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
.../bindings/net/mediatek-dwmac.txt | 91 ----------
.../bindings/net/mediatek-dwmac.yaml | 155 ++++++++++++++++++
2 files changed, 155 insertions(+), 91 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt
create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt
deleted file mode 100644
index afbcaebf062e..000000000000
--- a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt
+++ /dev/null
@@ -1,91 +0,0 @@
-MediaTek DWMAC glue layer controller
-
-This file documents platform glue layer for stmmac.
-Please see stmmac.txt for the other unchanged properties.
-
-The device node has following properties.
-
-Required properties:
-- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC
-- reg: Address and length of the register set for the device
-- interrupts: Should contain the MAC interrupts
-- interrupt-names: Should contain a list of interrupt names corresponding to
- the interrupts in the interrupts property, if available.
- Should be "macirq" for the main MAC IRQ
-- clocks: Must contain a phandle for each entry in clock-names.
-- clock-names: The name of the clock listed in the clocks property. These are
- "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC.
-- mac-address: See ethernet.txt in the same directory
-- phy-mode: See ethernet.txt in the same directory
-- mediatek,pericfg: A phandle to the syscon node that control ethernet
- interface and timing delay.
-
-Optional properties:
-- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0.
- It should be defined for RGMII/MII interface.
- It should be defined for RMII interface when the reference clock is from MT2712 SoC.
-- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0.
- It should be defined for RGMII/MII interface.
- It should be defined for RMII interface.
-Both delay properties need to be a multiple of 170 for RGMII interface,
-or will round down. Range 0~31*170.
-Both delay properties need to be a multiple of 550 for MII/RMII interface,
-or will round down. Range 0~31*550.
-
-- mediatek,rmii-rxc: boolean property, if present indicates that the RMII
- reference clock, which is from external PHYs, is connected to RXC pin
- on MT2712 SoC.
- Otherwise, is connected to TXC pin.
-- mediatek,rmii-clk-from-mac: boolean property, if present indicates that
- MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only.
-- mediatek,txc-inverse: boolean property, if present indicates that
- 1. tx clock will be inversed in MII/RGMII case,
- 2. tx clock inside MAC will be inversed relative to reference clock
- which is from external PHYs in RMII case, and it rarely happen.
- 3. the reference clock, which outputs to TXC pin will be inversed in RMII case
- when the reference clock is from MT2712 SoC.
-- mediatek,rxc-inverse: boolean property, if present indicates that
- 1. rx clock will be inversed in MII/RGMII case.
- 2. reference clock will be inversed when arrived at MAC in RMII case, when
- the reference clock is from external PHYs.
- 3. the inside clock, which be sent to MAC, will be inversed in RMII case when
- the reference clock is from MT2712 SoC.
-- assigned-clocks: mac_main and ptp_ref clocks
-- assigned-clock-parents: parent clocks of the assigned clocks
-
-Example:
- eth: ethernet@1101c000 {
- compatible = "mediatek,mt2712-gmac";
- reg = <0 0x1101c000 0 0x1300>;
- interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
- interrupt-names = "macirq";
- phy-mode ="rgmii-rxid";
- mac-address = [00 55 7b b5 7d f7];
- clock-names = "axi",
- "apb",
- "mac_main",
- "ptp_ref",
- "rmii_internal";
- clocks = <&pericfg CLK_PERI_GMAC>,
- <&pericfg CLK_PERI_GMAC_PCLK>,
- <&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
- assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
- assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
- <&topckgen CLK_TOP_APLL1_D3>,
- <&topckgen CLK_TOP_ETHERPLL_50M>;
- power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
- mediatek,pericfg = <&pericfg>;
- mediatek,tx-delay-ps = <1530>;
- mediatek,rx-delay-ps = <1530>;
- mediatek,rmii-rxc;
- mediatek,txc-inverse;
- mediatek,rxc-inverse;
- snps,txpbl = <1>;
- snps,rxpbl = <1>;
- snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
- snps,reset-active-low;
- };
diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
new file mode 100644
index 000000000000..8ad6e19661b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mediatek-dwmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek DWMAC glue layer controller
+
+maintainers:
+ - Biao Huang <[email protected]>
+
+description:
+ This file documents platform glue layer for stmmac.
+
+# We need a select here so we don't match all nodes with 'snps,dwmac'
+select:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - mediatek,mt2712-gmac
+ required:
+ - compatible
+
+allOf:
+ - $ref: "snps,dwmac.yaml#"
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - mediatek,mt2712-gmac
+ - const: snps,dwmac-4.20a
+
+ clocks:
+ items:
+ - description: AXI clock
+ - description: APB clock
+ - description: MAC Main clock
+ - description: PTP clock
+ - description: RMII reference clock provided by MAC
+
+ clock-names:
+ items:
+ - const: axi
+ - const: apb
+ - const: mac_main
+ - const: ptp_ref
+ - const: rmii_internal
+
+ mediatek,pericfg:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The phandle to the syscon node that control ethernet
+ interface and timing delay.
+
+ mediatek,tx-delay-ps:
+ description:
+ The internal TX clock delay (provided by this driver) in nanoseconds.
+ For MT2712 RGMII interface, Allowed value need to be a multiple of 170,
+ or will round down. Range 0~31*170.
+ For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
+ or will round down. Range 0~31*550.
+
+ mediatek,rx-delay-ps:
+ description:
+ The internal RX clock delay (provided by this driver) in nanoseconds.
+ For MT2712 RGMII interface, Allowed value need to be a multiple of 170,
+ or will round down. Range 0~31*170.
+ For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
+ or will round down. Range 0~31*550.
+
+ mediatek,rmii-rxc:
+ type: boolean
+ description:
+ If present, indicates that the RMII reference clock, which is from external
+ PHYs, is connected to RXC pin. Otherwise, is connected to TXC pin.
+
+ mediatek,rmii-clk-from-mac:
+ type: boolean
+ description:
+ If present, indicates that MAC provides the RMII reference clock, which
+ outputs to TXC pin only.
+
+ mediatek,txc-inverse:
+ type: boolean
+ description:
+ If present, indicates that
+ 1. tx clock will be inversed in MII/RGMII case,
+ 2. tx clock inside MAC will be inversed relative to reference clock
+ which is from external PHYs in RMII case, and it rarely happen.
+ 3. the reference clock, which outputs to TXC pin will be inversed in RMII case
+ when the reference clock is from MAC.
+
+ mediatek,rxc-inverse:
+ type: boolean
+ description:
+ If present, indicates that
+ 1. rx clock will be inversed in MII/RGMII case.
+ 2. reference clock will be inversed when arrived at MAC in RMII case, when
+ the reference clock is from external PHYs.
+ 3. the inside clock, which be sent to MAC, will be inversed in RMII case when
+ the reference clock is from MAC.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-names
+ - clocks
+ - clock-names
+ - phy-mode
+ - mediatek,pericfg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt2712-clk.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/power/mt2712-power.h>
+
+ eth: ethernet@1101c000 {
+ compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
+ reg = <0x1101c000 0x1300>;
+ interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "macirq";
+ phy-mode ="rgmii-rxid";
+ mac-address = [00 55 7b b5 7d f7];
+ clock-names = "axi",
+ "apb",
+ "mac_main",
+ "ptp_ref",
+ "rmii_internal";
+ clocks = <&pericfg CLK_PERI_GMAC>,
+ <&pericfg CLK_PERI_GMAC_PCLK>,
+ <&topckgen CLK_TOP_ETHER_125M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
+ assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
+ <&topckgen CLK_TOP_APLL1_D3>,
+ <&topckgen CLK_TOP_ETHERPLL_50M>;
+ power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
+ mediatek,pericfg = <&pericfg>;
+ mediatek,tx-delay-ps = <1530>;
+ snps,txpbl = <1>;
+ snps,rxpbl = <1>;
+ snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
--
2.25.1
On Mon, 17 Jan 2022 15:07:06 +0800, Biao Huang wrote:
> Add binding document for the ethernet on mt8195.
>
> Signed-off-by: Biao Huang <[email protected]>
> ---
> .../bindings/net/mediatek-dwmac.yaml | 28 ++++++++++++++++---
> 1 file changed, 24 insertions(+), 4 deletions(-)
>
Running 'make dtbs_check' with the schema in this patch gives the
following warnings. Consider if they are expected or the schema is
incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check.
This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/patch/1580608
ethernet@1101c000: clock-names: ['axi', 'apb', 'mac_main', 'ptp_ref'] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: clocks: [[27, 34], [27, 37], [6, 154], [6, 155]] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: ['mediatek,mt2712-gmac'] does not contain items matching the given schema
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: Unevaluated properties are not allowed ('compatible', 'reg', 'interrupts', 'interrupt-names', 'mac-address', 'clock-names', 'clocks', 'power-domains', 'snps,axi-config', 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,txpbl', 'snps,rxpbl', 'clk_csr', 'phy-mode', 'phy-handle', 'snps,reset-gpio', 'mdio' were unexpected)
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
Dear Rob,
Thanks for your comments.
If patch "[PATCH net-next v12 4/7] arm64: dts: mt2712: update
ethernet device node" is applied with dt-binding patches, "make
dtbs_check" will not report
such warnings.
Please review it kindly, thanks.
On Mon, 2022-01-17 at 09:35 -0600, Rob Herring wrote:
> On Mon, 17 Jan 2022 15:07:06 +0800, Biao Huang wrote:
> > Add binding document for the ethernet on mt8195.
> >
> > Signed-off-by: Biao Huang <[email protected]>
> > ---
> > .../bindings/net/mediatek-dwmac.yaml | 28
> > ++++++++++++++++---
> > 1 file changed, 24 insertions(+), 4 deletions(-)
> >
>
> Running 'make dtbs_check' with the schema in this patch gives the
> following warnings. Consider if they are expected or the schema is
> incorrect. These may not be new warnings.
>
> Note that it is not yet a requirement to have 0 warnings for
> dtbs_check.
> This will change in the future.
>
> Full log is available here:
> https://patchwork.ozlabs.org/patch/1580608
>
>
> ethernet@1101c000: clock-names: ['axi', 'apb', 'mac_main', 'ptp_ref']
> is too short
> arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
>
> ethernet@1101c000: clocks: [[27, 34], [27, 37], [6, 154], [6, 155]]
> is too short
> arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
>
> ethernet@1101c000: compatible: ['mediatek,mt2712-gmac'] does not
> contain items matching the given schema
> arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
>
> ethernet@1101c000: compatible: 'oneOf' conditional failed, one must
> be fixed:
> arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
>
> ethernet@1101c000: Unevaluated properties are not allowed
> ('compatible', 'reg', 'interrupts', 'interrupt-names', 'mac-address',
> 'clock-names', 'clocks', 'power-domains', 'snps,axi-config',
> 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,txpbl',
> 'snps,rxpbl', 'clk_csr', 'phy-mode', 'phy-handle', 'snps,reset-gpio',
> 'mdio' were unexpected)
> arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
>
Dear Matthias,
Any comments about this dts patch?
Thanks in advance.
Regards!
Biao
On Mon, 2022-01-17 at 15:07 +0800, Biao Huang wrote:
> Since there are some changes in ethernet driver:
> update ethernet device node in dts to accommodate to it.
>
> 1. stmmac_probe_config_dt() in stmmac_platform.c will initialize
> specified
> parameters according to compatible string "snps,dwmac-4.20a",
> then,
> dwmac-mediatek.c can skip the initialization if add compatible
> string
> "snps,dwmac-4.20a" in eth device node.
> 2. commit 882007ed7832 ("net-next: dt-binding: dwmac-mediatek: add
> more
> description for RMII") added rmii internal support, we should add
> corresponding clocks/clocks-names in eth device node.
> 3. add "snps,reset-delays-us = <0 10000 10000>;" to ensure reset
> delay
> can meet PHY requirement.
>
> Signed-off-by: Biao Huang <[email protected]>
> ---
> arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 +
> arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++-----
> 2 files changed, 10 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> index 7d369fdd3117..11aa135aa0f3 100644
> --- a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> @@ -110,6 +110,7 @@ ð {
> phy-handle = <ðernet_phy0>;
> mediatek,tx-delay-ps = <1530>;
> snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
> + snps,reset-delays-us = <0 10000 10000>;
> pinctrl-names = "default", "sleep";
> pinctrl-0 = <ð_default>;
> pinctrl-1 = <ð_sleep>;
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> index a9cca9c146fd..9e850e04fffb 100644
> --- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> @@ -726,7 +726,7 @@ queue2 {
> };
>
> eth: ethernet@1101c000 {
> - compatible = "mediatek,mt2712-gmac";
> + compatible = "mediatek,mt2712-gmac", "snps,dwmac-
> 4.20a";
> reg = <0 0x1101c000 0 0x1300>;
> interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
> interrupt-names = "macirq";
> @@ -734,15 +734,19 @@ eth: ethernet@1101c000 {
> clock-names = "axi",
> "apb",
> "mac_main",
> - "ptp_ref";
> + "ptp_ref",
> + "rmii_internal";
> clocks = <&pericfg CLK_PERI_GMAC>,
> <&pericfg CLK_PERI_GMAC_PCLK>,
> <&topckgen CLK_TOP_ETHER_125M_SEL>,
> - <&topckgen CLK_TOP_ETHER_50M_SEL>;
> + <&topckgen CLK_TOP_ETHER_50M_SEL>,
> + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
> assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
> - <&topckgen CLK_TOP_ETHER_50M_SEL>;
> + <&topckgen CLK_TOP_ETHER_50M_SEL>,
> + <&topckgen
> CLK_TOP_ETHER_50M_RMII_SEL>;
> assigned-clock-parents = <&topckgen
> CLK_TOP_ETHERPLL_125M>,
> - <&topckgen CLK_TOP_APLL1_D3>;
> + <&topckgen CLK_TOP_APLL1_D3>,
> + <&topckgen
> CLK_TOP_ETHERPLL_50M>;
> power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
> mediatek,pericfg = <&pericfg>;
> snps,axi-config = <&stmmac_axi_setup>;
On Mon, 17 Jan 2022 15:07:06 +0800, Biao Huang wrote:
> Add binding document for the ethernet on mt8195.
>
> Signed-off-by: Biao Huang <[email protected]>
> ---
> .../bindings/net/mediatek-dwmac.yaml | 28 ++++++++++++++++---
> 1 file changed, 24 insertions(+), 4 deletions(-)
>
Reviewed-by: Rob Herring <[email protected]>