2018-08-18 16:04:50

by Ryder Lee

[permalink] [raw]
Subject: [PATCH v1 1/5] arm64: dts: mt7622: add timer, CCI-400 and PMU nodes

Add device tree entries for timer, ARM CCI-400 and its PMU.
Otherwise, we add a cortex-a53-pmu node to enable hw perfevents.

Signed-off-by: Ryder Lee <[email protected]>
---
change since v1:
- add a pmu node.
---
arch/arm64/boot/dts/mediatek/mt7622.dtsi | 55 ++++++++++++++++++++++++++++++++
1 file changed, 55 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index de2c47bd..d297100 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -79,6 +79,7 @@
#cooling-cells = <2>;
enable-method = "psci";
clock-frequency = <1300000000>;
+ cci-control-port = <&cci_control2>;
};

cpu1: cpu@1 {
@@ -92,6 +93,7 @@
#cooling-cells = <2>;
enable-method = "psci";
clock-frequency = <1300000000>;
+ cci-control-port = <&cci_control2>;
};
};

@@ -113,6 +115,13 @@
method = "smc";
};

+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-affinity = <&cpu0>, <&cpu1>;
+ };
+
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
@@ -218,6 +227,16 @@
#reset-cells = <1>;
};

+ timer: timer@10004000 {
+ compatible = "mediatek,mt7622-timer",
+ "mediatek,mt6577-timer";
+ reg = <0 0x10004000 0 0x80>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_APXGPT_PD>,
+ <&topckgen CLK_TOP_RTC>;
+ clock-names = "system-clk", "rtc-clk";
+ };
+
scpsys: scpsys@10006000 {
compatible = "mediatek,mt7622-scpsys",
"syscon";
@@ -325,6 +344,42 @@
<0 0x10360000 0 0x2000>;
};

+ cci: cci@10390000 {
+ compatible = "arm,cci-400";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0x10390000 0 0x1000>;
+ ranges = <0 0 0x10390000 0x10000>;
+
+ cci_control0: slave-if@1000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace-lite";
+ reg = <0x1000 0x1000>;
+ };
+
+ cci_control1: slave-if@4000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x4000 0x1000>;
+ };
+
+ cci_control2: slave-if@5000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x5000 0x1000>;
+ };
+
+ pmu@9000 {
+ compatible = "arm,cci-400-pmu,r1";
+ reg = <0x9000 0x5000>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
auxadc: adc@11001000 {
compatible = "mediatek,mt7622-auxadc";
reg = <0 0x11001000 0 0x1000>;
--
1.9.1



2018-08-18 16:04:45

by Ryder Lee

[permalink] [raw]
Subject: [PATCH v1 3/5] arm64: dts: mt7622: fix ram size for rfb1

Fix ram size to 512 megabytes and sort nodes in alphabetical order.

Signed-off-by: Ryder Lee <[email protected]>
Acked-by: Sean Wang <[email protected]>
---
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts | 196 +++++++++++++--------------
1 file changed, 98 insertions(+), 98 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
index a747b7b..dcad086 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
@@ -51,7 +51,7 @@
};

memory {
- reg = <0 0x40000000 0 0x3F000000>;
+ reg = <0 0x40000000 0 0x20000000>;
};

reg_1p8v: regulator-1p8v {
@@ -81,6 +81,103 @@
};
};

+&bch {
+ status = "disabled";
+};
+
+&btif {
+ status = "okay";
+};
+
+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&irrx_pins>;
+ status = "okay";
+};
+
+&eth {
+ pinctrl-names = "default";
+ pinctrl-0 = <&eth_pins>;
+ status = "okay";
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy5>;
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ phy-mode = "sgmii";
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&emmc_pins_default>;
+ pinctrl-1 = <&emmc_pins_uhs>;
+ status = "okay";
+ bus-width = <8>;
+ max-frequency = <50000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_1p8v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+ non-removable;
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&sd0_pins_default>;
+ pinctrl-1 = <&sd0_pins_uhs>;
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ cap-sd-highspeed;
+ r_smpl = <1>;
+ cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_3p3v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+};
+
+&nandc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&parallel_nand_pins>;
+ status = "disabled";
+};
+
+&nor_flash {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_nor_pins>;
+ status = "disabled";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ };
+};
+
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pcie0_pins>;
@@ -344,103 +441,6 @@
};
};

-&bch {
- status = "disabled";
-};
-
-&btif {
- status = "okay";
-};
-
-&cir {
- pinctrl-names = "default";
- pinctrl-0 = <&irrx_pins>;
- status = "okay";
-};
-
-&eth {
- pinctrl-names = "default";
- pinctrl-0 = <&eth_pins>;
- status = "okay";
-
- gmac1: mac@1 {
- compatible = "mediatek,eth-mac";
- reg = <1>;
- phy-handle = <&phy5>;
- };
-
- mdio-bus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy5: ethernet-phy@5 {
- reg = <5>;
- phy-mode = "sgmii";
- };
- };
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "okay";
-};
-
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "okay";
-};
-
-&mmc0 {
- pinctrl-names = "default", "state_uhs";
- pinctrl-0 = <&emmc_pins_default>;
- pinctrl-1 = <&emmc_pins_uhs>;
- status = "okay";
- bus-width = <8>;
- max-frequency = <50000000>;
- cap-mmc-highspeed;
- mmc-hs200-1_8v;
- vmmc-supply = <&reg_3p3v>;
- vqmmc-supply = <&reg_1p8v>;
- assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
- assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
- non-removable;
-};
-
-&mmc1 {
- pinctrl-names = "default", "state_uhs";
- pinctrl-0 = <&sd0_pins_default>;
- pinctrl-1 = <&sd0_pins_uhs>;
- status = "okay";
- bus-width = <4>;
- max-frequency = <50000000>;
- cap-sd-highspeed;
- r_smpl = <1>;
- cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
- vmmc-supply = <&reg_3p3v>;
- vqmmc-supply = <&reg_3p3v>;
- assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
- assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
-};
-
-&nandc {
- pinctrl-names = "default";
- pinctrl-0 = <&parallel_nand_pins>;
- status = "disabled";
-};
-
-&nor_flash {
- pinctrl-names = "default";
- pinctrl-0 = <&spi_nor_pins>;
- status = "disabled";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- };
-};
-
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm7_pins>;
--
1.9.1


2018-08-18 16:04:57

by Ryder Lee

[permalink] [raw]
Subject: [PATCH v1 4/5] arm64: dts: mt7622: add bananapi BPI-R64 board

Add support for the bananapi R64 (BPI-R64) development board from
BIPAI KEJI. Detailed hardware information for BPI-R64 which could be
found on http://wiki.banana-pi.org/Banana_Pi_BPI-R64

Signed-off-by: Ryder Lee <[email protected]>
---
changes since v1:
- add missing sata nodes.
- fix pinctrl-0 for pcie@1,0.
- switch goio keys from polling mode to intterupt mode.
- add gpio-led nodes.
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts | 530 +++++++++++++++++++++
2 files changed, 531 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 5b7fd6a..e8f952f 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -5,4 +5,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
new file mode 100644
index 0000000..5d6005c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
@@ -0,0 +1,530 @@
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ * Author: Ryder Lee <[email protected]>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7622.dtsi"
+#include "mt6380.dtsi"
+
+/ {
+ model = "Bananapi BPI-R64";
+ compatible = "bananapi,bpi-r64", "mediatek,mt7622";
+
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512";
+ };
+
+ cpus {
+ cpu@0 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+
+ cpu@1 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ factory {
+ label = "factory";
+ linux,code = <BTN_0>;
+ gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 102 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ green {
+ label = "bpi-r64:pio:green";
+ gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red {
+ label = "bpi-r64:pio:red";
+ gpios = <&pio 88 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x40000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&bch {
+ status = "disabled";
+};
+
+&btif {
+ status = "okay";
+};
+
+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&irrx_pins>;
+ status = "okay";
+};
+
+&eth {
+ pinctrl-names = "default";
+ pinctrl-0 = <&eth_pins>;
+ status = "okay";
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy5>;
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ phy-mode = "sgmii";
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&emmc_pins_default>;
+ pinctrl-1 = <&emmc_pins_uhs>;
+ status = "okay";
+ bus-width = <8>;
+ max-frequency = <50000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_1p8v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+ non-removable;
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&sd0_pins_default>;
+ pinctrl-1 = <&sd0_pins_uhs>;
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ cap-sd-highspeed;
+ r_smpl = <1>;
+ cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_3p3v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+};
+
+&nandc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&parallel_nand_pins>;
+ status = "disabled";
+};
+
+&nor_flash {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_nor_pins>;
+ status = "disabled";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
+ status = "okay";
+
+ pcie@0,0 {
+ status = "okay";
+ };
+
+ pcie@1,0 {
+ status = "okay";
+ };
+};
+
+&pio {
+ /* Attention: GPIO 90 is used to switch between PCIe@1,0 and
+ * SATA functions. i.e. output-high: PCIe, output-low: SATA
+ */
+ asm_sel {
+ gpio-hog;
+ gpios = <90 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+
+ /* eMMC is shared pin with parallel NAND */
+ emmc_pins_default: emmc-pins-default {
+ mux {
+ function = "emmc", "emmc_rst";
+ groups = "emmc";
+ };
+
+ /* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
+ * "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
+ * DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
+ */
+ conf-cmd-dat {
+ pins = "NDL0", "NDL1", "NDL2",
+ "NDL3", "NDL4", "NDL5",
+ "NDL6", "NDL7", "NRB";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "NCLE";
+ bias-pull-down;
+ };
+ };
+
+ emmc_pins_uhs: emmc-pins-uhs {
+ mux {
+ function = "emmc";
+ groups = "emmc";
+ };
+
+ conf-cmd-dat {
+ pins = "NDL0", "NDL1", "NDL2",
+ "NDL3", "NDL4", "NDL5",
+ "NDL6", "NDL7", "NRB";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "NCLE";
+ drive-strength = <4>;
+ bias-pull-down;
+ };
+ };
+
+ eth_pins: eth-pins {
+ mux {
+ function = "eth";
+ groups = "mdc_mdio", "rgmii_via_gmac2";
+ };
+ };
+
+ i2c1_pins: i2c1-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c1_0";
+ };
+ };
+
+ i2c2_pins: i2c2-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c2_0";
+ };
+ };
+
+ i2s1_pins: i2s1-pins {
+ mux {
+ function = "i2s";
+ groups = "i2s_out_mclk_bclk_ws",
+ "i2s1_in_data",
+ "i2s1_out_data";
+ };
+
+ conf {
+ pins = "I2S1_IN", "I2S1_OUT", "I2S_BCLK",
+ "I2S_WS", "I2S_MCLK";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+ };
+
+ irrx_pins: irrx-pins {
+ mux {
+ function = "ir";
+ groups = "ir_1_rx";
+ };
+ };
+
+ irtx_pins: irtx-pins {
+ mux {
+ function = "ir";
+ groups = "ir_1_tx";
+ };
+ };
+
+ /* Parallel nand is shared pin with eMMC */
+ parallel_nand_pins: parallel-nand-pins {
+ mux {
+ function = "flash";
+ groups = "par_nand";
+ };
+ };
+
+ pcie0_pins: pcie0-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie0_pad_perst",
+ "pcie0_1_waken",
+ "pcie0_1_clkreq";
+ };
+ };
+
+ pcie1_pins: pcie1-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie1_pad_perst",
+ "pcie1_0_waken",
+ "pcie1_0_clkreq";
+ };
+ };
+
+ pmic_bus_pins: pmic-bus-pins {
+ mux {
+ function = "pmic";
+ groups = "pmic_bus";
+ };
+ };
+
+ pwm7_pins: pwm1-2-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm_ch7_2";
+ };
+ };
+
+ wled_pins: wled-pins {
+ mux {
+ function = "led";
+ groups = "wled";
+ };
+ };
+
+ sd0_pins_default: sd0-pins-default {
+ mux {
+ function = "sd";
+ groups = "sd_0";
+ };
+
+ /* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
+ * "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
+ * DAT2, DAT3, CMD, CLK for SD respectively.
+ */
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ conf-clk {
+ pins = "I2S3_OUT";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+ conf-cd {
+ pins = "TXD3";
+ bias-pull-up;
+ };
+ };
+
+ sd0_pins_uhs: sd0-pins-uhs {
+ mux {
+ function = "sd";
+ groups = "sd_0";
+ };
+
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "I2S3_OUT";
+ bias-pull-down;
+ };
+ };
+
+ /* Serial NAND is shared pin with SPI-NOR */
+ serial_nand_pins: serial-nand-pins {
+ mux {
+ function = "flash";
+ groups = "snfi";
+ };
+ };
+
+ spic0_pins: spic0-pins {
+ mux {
+ function = "spi";
+ groups = "spic0_0";
+ };
+ };
+
+ spic1_pins: spic1-pins {
+ mux {
+ function = "spi";
+ groups = "spic1_0";
+ };
+ };
+
+ /* SPI-NOR is shared pin with serial NAND */
+ spi_nor_pins: spi-nor-pins {
+ mux {
+ function = "flash";
+ groups = "spi_nor";
+ };
+ };
+
+ /* serial NAND is shared pin with SPI-NOR */
+ serial_nand_pins: serial-nand-pins {
+ mux {
+ function = "flash";
+ groups = "snfi";
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ mux {
+ function = "uart";
+ groups = "uart0_0_tx_rx" ;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ mux {
+ function = "uart";
+ groups = "uart2_1_tx_rx" ;
+ };
+ };
+
+ watchdog_pins: watchdog-pins {
+ mux {
+ function = "watchdog";
+ groups = "watchdog";
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm7_pins>;
+ status = "okay";
+};
+
+&pwrap {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_bus_pins>;
+
+ status = "okay";
+};
+
+&sata {
+ status = "disable";
+};
+
+&sata_phy {
+ status = "disable";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic0_pins>;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic1_pins>;
+ status = "okay";
+};
+
+&ssusb {
+ vusb33-supply = <&reg_3p3v>;
+ vbus-supply = <&reg_5v>;
+ status = "okay";
+};
+
+&u3phy {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ pinctrl-names = "default";
+ pinctrl-0 = <&watchdog_pins>;
+ status = "okay";
+};
--
1.9.1


2018-08-18 16:05:36

by Ryder Lee

[permalink] [raw]
Subject: [PATCH v1 2/5] arm64: dts: mt7622: add a bluetooth 5 device node

Add a built-in bluetooth 5 support for MT7622.

Signed-off-by: Ryder Lee <[email protected]>
Acked-by: Sean Wang <[email protected]>
---
arch/arm64/boot/dts/mediatek/mt7622.dtsi | 7 +++++++
1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index d297100..b4d7934 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -530,6 +530,13 @@
reg-shift = <2>;
reg-io-width = <4>;
status = "disabled";
+
+ bluetooth {
+ compatible = "mediatek,mt7622-bluetooth";
+ power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
+ clocks = <&clk25m>;
+ clock-names = "ref";
+ };
};

nandc: nfi@1100d000 {
--
1.9.1


2018-08-18 16:05:56

by Ryder Lee

[permalink] [raw]
Subject: [PATCH v1 5/5] dt-bindings: arm: mediatek: add support for bananapi BPI-R64 board

Update binding document for bananapi BPI-R64 board being supported.

Signed-off-by: Ryder Lee <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/arm/mediatek.txt | 3 +++
1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt
index 8f260e5..d30f6ce 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@@ -57,6 +57,9 @@ Supported boards:
- Reference board variant 1 for MT7622:
Required root node properties:
- compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
+- Bananapi BPI-R64 for MT7622:
+ Required root node properties:
+ - compatible = "bananapi,bpi-r64", "mediatek,mt7622";
- Reference board for MT7623a with eMMC:
Required root node properties:
- compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623";
--
1.9.1


2018-09-25 15:10:30

by Matthias Brugger

[permalink] [raw]
Subject: Re: [PATCH v1 1/5] arm64: dts: mt7622: add timer, CCI-400 and PMU nodes

Whole series pushed to v4.19-next/dts64

Thanks!

On 18/08/2018 18:02, Ryder Lee wrote:
> Add device tree entries for timer, ARM CCI-400 and its PMU.
> Otherwise, we add a cortex-a53-pmu node to enable hw perfevents.
>
> Signed-off-by: Ryder Lee <[email protected]>
> ---
> change since v1:
> - add a pmu node.
> ---
> arch/arm64/boot/dts/mediatek/mt7622.dtsi | 55 ++++++++++++++++++++++++++++++++
> 1 file changed, 55 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
> index de2c47bd..d297100 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
> @@ -79,6 +79,7 @@
> #cooling-cells = <2>;
> enable-method = "psci";
> clock-frequency = <1300000000>;
> + cci-control-port = <&cci_control2>;
> };
>
> cpu1: cpu@1 {
> @@ -92,6 +93,7 @@
> #cooling-cells = <2>;
> enable-method = "psci";
> clock-frequency = <1300000000>;
> + cci-control-port = <&cci_control2>;
> };
> };
>
> @@ -113,6 +115,13 @@
> method = "smc";
> };
>
> + pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 9 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-affinity = <&cpu0>, <&cpu1>;
> + };
> +
> reserved-memory {
> #address-cells = <2>;
> #size-cells = <2>;
> @@ -218,6 +227,16 @@
> #reset-cells = <1>;
> };
>
> + timer: timer@10004000 {
> + compatible = "mediatek,mt7622-timer",
> + "mediatek,mt6577-timer";
> + reg = <0 0x10004000 0 0x80>;
> + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_INFRA_APXGPT_PD>,
> + <&topckgen CLK_TOP_RTC>;
> + clock-names = "system-clk", "rtc-clk";
> + };
> +
> scpsys: scpsys@10006000 {
> compatible = "mediatek,mt7622-scpsys",
> "syscon";
> @@ -325,6 +344,42 @@
> <0 0x10360000 0 0x2000>;
> };
>
> + cci: cci@10390000 {
> + compatible = "arm,cci-400";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0 0x10390000 0 0x1000>;
> + ranges = <0 0 0x10390000 0x10000>;
> +
> + cci_control0: slave-if@1000 {
> + compatible = "arm,cci-400-ctrl-if";
> + interface-type = "ace-lite";
> + reg = <0x1000 0x1000>;
> + };
> +
> + cci_control1: slave-if@4000 {
> + compatible = "arm,cci-400-ctrl-if";
> + interface-type = "ace";
> + reg = <0x4000 0x1000>;
> + };
> +
> + cci_control2: slave-if@5000 {
> + compatible = "arm,cci-400-ctrl-if";
> + interface-type = "ace";
> + reg = <0x5000 0x1000>;
> + };
> +
> + pmu@9000 {
> + compatible = "arm,cci-400-pmu,r1";
> + reg = <0x9000 0x5000>;
> + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> auxadc: adc@11001000 {
> compatible = "mediatek,mt7622-auxadc";
> reg = <0 0x11001000 0 0x1000>;
>