zcu104-revA has node below pinctrl which is not the same on revC. Sync
location for easier comparison.
Also zc1751-dc1 is not using this position.
Signed-off-by: Michal Simek <[email protected]>
---
.../boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 14 +++++++-------
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts | 14 +++++++-------
2 files changed, 14 insertions(+), 14 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
index 9f176307b62a..d78439e891b9 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -58,13 +58,6 @@ clock_si5338_3: clk150 {
};
};
-&psgtr {
- status = "okay";
- /* dp, usb3, sata */
- clocks = <&clock_si5338_0>, <&clock_si5338_2>, <&clock_si5338_3>;
- clock-names = "ref1", "ref2", "ref3";
-};
-
&fpd_dma_chan1 {
status = "okay";
};
@@ -340,6 +333,13 @@ conf {
};
};
+&psgtr {
+ status = "okay";
+ /* dp, usb3, sata */
+ clocks = <&clock_si5338_0>, <&clock_si5338_2>, <&clock_si5338_3>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&qspi {
status = "okay";
flash@0 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
index fb8d76b5c27f..c21d9612ce04 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -429,6 +429,13 @@ conf-tx {
};
};
+&psgtr {
+ status = "okay";
+ /* nc, sata, usb3, dp */
+ clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&qspi {
status = "okay";
flash@0 {
@@ -446,13 +453,6 @@ &rtc {
status = "okay";
};
-&psgtr {
- status = "okay";
- /* nc, sata, usb3, dp */
- clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
- clock-names = "ref1", "ref2", "ref3";
-};
-
&sata {
status = "okay";
/* SATA OOB timing settings */
--
2.31.1