sorry, I haven't been keeping up with the changes in 2.5, but I can't get
pppd to work with 2.5.59, it dies with error code 1 while it works alright
with 2.4.20...
This is the first 2.5 kernel i've tried out, first I went for a wild goose
chase in finding a version of modutils to go with the shiny new bzImage,
then I finally downloaded module-init*, and installed it over the previous
tools, then I remembered that I still might have to use 2.4 (which I am), so
I fetched modutils again and installed it, then I installed module-init*
with make *specialoption*, and then (aaah, finished...)but no, I cannot
dial to my isp...
pppd dies with error code 1
Also, Does a Pentium4 have a local APIC? IO APIC?
I selected it anyway in the kernel config, and it shows some warning message
at boot:
: ENABLING IO-APIC IRQs
: init IO_APIC IRQs
: IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-21, 2-22, 2-23 not
connected.
: ..TIMER: vector=0x31 pin1=2 pin2=0
: number of MP IRQ sources: 17.
: number of IO-APIC #2 registers: 24.
: testing the IO APIC.......................
:
: IO APIC #2......
: .... register #00: 02000000
: ....... : physical APIC id: 02
: ....... : Delivery Type: 0
: ....... : LTS : 0
: .... register #01: 00178000
: ....... : max redirection entries: 0017
: ....... : PRQ implemented: 1
: ....... : IO APIC version: 0000
: WARNING: unexpected IO-APIC, please mail
: to [email protected]
: .... IRQ redirection table:
: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
: 00 000 00 1 0 0 0 0 0 0 00
: 01 001 01 0 0 0 0 0 1 1 39
: 02 001 01 0 0 0 0 0 1 1 31
: 03 001 01 0 0 0 0 0 1 1 41
: 04 001 01 0 0 0 0 0 1 1 49
: 05 001 01 0 0 0 0 0 1 1 51
: 06 001 01 0 0 0 0 0 1 1 59
: 07 001 01 0 0 0 0 0 1 1 61
: 08 001 01 0 0 0 0 0 1 1 69
: 09 001 01 0 0 0 0 0 1 1 71
: 0a 001 01 0 0 0 0 0 1 1 79
: 0b 001 01 0 0 0 0 0 1 1 81
: 0c 001 01 0 0 0 0 0 1 1 89
: 0d 001 01 0 0 0 0 0 1 1 91
: 0e 001 01 0 0 0 0 0 1 1 99
: 0f 001 01 0 0 0 0 0 1 1 A1
: 10 000 00 1 0 0 0 0 0 0 00
: 11 000 00 1 0 0 0 0 0 0 00
: 12 000 00 1 0 0 0 0 0 0 00
: 13 000 00 1 0 0 0 0 0 0 00
: 14 001 01 1 1 0 1 0 1 1 71
: 15 000 00 1 0 0 0 0 0 0 00
: 16 000 00 1 0 0 0 0 0 0 00
: 17 000 00 1 0 0 0 0 0 0 00
: IRQ to pin mappings:
: IRQ0 -> 0:2
: IRQ1 -> 0:1
: IRQ3 -> 0:3
: IRQ4 -> 0:4
: IRQ5 -> 0:5
: IRQ6 -> 0:6
: IRQ7 -> 0:7
: IRQ8 -> 0:8
: IRQ9 -> 0:9-> 0:20
: IRQ10 -> 0:10
: IRQ11 -> 0:11
: IRQ12 -> 0:12
: IRQ13 -> 0:13
: IRQ14 -> 0:14
: IRQ15 -> 0:15
: .................................... done.
: Using local APIC timer interrupts.
: calibrating APIC timer ...
: ..... CPU clock speed is 2659.0663 MHz.
: ..... host bus clock speed is 132.0983 MHz.
Is anything wrong with this?
thank you very much for reading/replying
On Sun, Feb 02, 2003 at 10:47:37AM -0700, [email protected] wrote:
> sorry, I haven't been keeping up with the changes in 2.5, but I can't get
> pppd to work with 2.5.59, it dies with error code 1 while it works alright
> with 2.4.20...
You need to look in the system log files (typically /var/log/messages) to
see why pppd isn't happy.
--
Russell King ([email protected]) The developer of ARM Linux
http://www.arm.linux.org.uk/personal/aboutme.html
Russell King writes:
> On Sun, Feb 02, 2003 at 10:47:37AM -0700, [email protected] wrote:
>> sorry, I haven't been keeping up with the changes in 2.5, but I can't get
>> pppd to work with 2.5.59, it dies with error code 1 while it works alright
>> with 2.4.20...
>
> You need to look in the system log files (typically /var/log/messages) to
> see why pppd isn't happy.
Oh yes, sorry I forgot, module tty_ldisk3 cannot be found, so ppp dies with
exit status 1...
I didn't think ppp needs anything other than ppp_generic, the serial driver
for ppp and the compression modules...
What is tty_ldisk3? could you help me on this?
Also, I haven't been able to solve the cpu problem...
and also, modprobe warns of unknown symbols in /etc/modules.devfs...although
the 2.4 kernel works fine...
On Sun, Feb 02, 2003 at 02:00:33PM -0700, [email protected] wrote:
> Oh yes, sorry I forgot, module tty_ldisk3 cannot be found, so ppp dies with
> exit status 1...
> I didn't think ppp needs anything other than ppp_generic, the serial driver
> for ppp and the compression modules...
> What is tty_ldisk3? could you help me on this?
It's the ppp line discipline. Add to /etc/modules.conf:
alias tty-ldisc-3 ppp_async
--
Russell King ([email protected]) The developer of ARM Linux
http://www.arm.linux.org.uk/personal/aboutme.html