Hi Greg,
Those are the remaining patches that are needed for the USB to work
with Hikey970.
This series address the comments made on v5. Sorry for taking so long to
return back on this. Got sidetracked by other unrelated stuff.
v6:
Only patch 3 was changed (*):
- Copyrights changed to "20xx-" in order to indicate just the start date
of the copyrights;
- HISI_8BITS_MASK is now defined as simply 0xff (without using GENMASK);
- There's no sense to mask the value read by regmap_read() when writing
it back to acknowledge that IRQs got handled;
- removed one extra tab from the regmap_config identation;
- if irq_create_mapping() fails, return -ENODEV;
- use devm_request_threaded_irq().
(*) as we're using --no-merges, in order to show the full code at renames,
patch 6 will also look different.
Mauro Carvalho Chehab (8):
staging: phy-hi3670-usb3: do a some minor cleanups
staging: hisi-spmi-controller: rename spmi-channel property
staging: hi6421-spmi-pmic: do some additional cleanups
phy: phy-hi3670-usb3: move driver from staging into phy
spmi: hisi-spmi-controller: move driver from staging
mfd: hi6421-spmi-pmic: move driver from staging
dts: hisilicon: add support for the PMIC found on Hikey 970
dts: hisilicon: add support for USB3 on Hikey 970
.../mfd/hisilicon,hi6421-spmi-pmic.yaml | 134 ++++
.../bindings/phy/hisilicon,hi3670-usb3.yaml | 73 ++
.../spmi/hisilicon,hisi-spmi-controller.yaml | 73 ++
MAINTAINERS | 23 +-
.../boot/dts/hisilicon/hi3670-hikey970.dts | 129 +++-
arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 56 ++
.../boot/dts/hisilicon/hikey970-pmic.dtsi | 87 +++
drivers/mfd/Kconfig | 16 +
drivers/mfd/Makefile | 1 +
drivers/mfd/hi6421-spmi-pmic.c | 311 ++++++++
drivers/phy/hisilicon/Kconfig | 10 +
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3670-usb3.c | 661 +++++++++++++++++
drivers/spmi/Kconfig | 9 +
drivers/spmi/Makefile | 1 +
drivers/spmi/hisi-spmi-controller.c | 367 ++++++++++
drivers/staging/Kconfig | 2 -
drivers/staging/Makefile | 1 -
drivers/staging/hikey9xx/Kconfig | 41 --
drivers/staging/hikey9xx/Makefile | 6 -
drivers/staging/hikey9xx/TODO | 5 -
drivers/staging/hikey9xx/hi6421-spmi-pmic.c | 297 --------
.../staging/hikey9xx/hisi-spmi-controller.c | 367 ----------
.../hikey9xx/hisilicon,hi6421-spmi-pmic.yaml | 135 ----
.../hisilicon,hisi-spmi-controller.yaml | 71 --
drivers/staging/hikey9xx/phy-hi3670-usb3.c | 668 ------------------
drivers/staging/hikey9xx/phy-hi3670-usb3.yaml | 73 --
27 files changed, 1932 insertions(+), 1686 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,hi3670-usb3.yaml
create mode 100644 Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml
create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
create mode 100644 drivers/mfd/hi6421-spmi-pmic.c
create mode 100644 drivers/phy/hisilicon/phy-hi3670-usb3.c
create mode 100644 drivers/spmi/hisi-spmi-controller.c
delete mode 100644 drivers/staging/hikey9xx/Kconfig
delete mode 100644 drivers/staging/hikey9xx/Makefile
delete mode 100644 drivers/staging/hikey9xx/TODO
delete mode 100644 drivers/staging/hikey9xx/hi6421-spmi-pmic.c
delete mode 100644 drivers/staging/hikey9xx/hisi-spmi-controller.c
delete mode 100644 drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml
delete mode 100644 drivers/staging/hikey9xx/hisilicon,hisi-spmi-controller.yaml
delete mode 100644 drivers/staging/hikey9xx/phy-hi3670-usb3.c
delete mode 100644 drivers/staging/hikey9xx/phy-hi3670-usb3.yaml
--
2.31.1
This driver is ready for mainstream. So, move it out of staging.
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
---
.../mfd/hisilicon,hi6421-spmi-pmic.yaml | 134 ++++++++
MAINTAINERS | 7 +
drivers/mfd/Kconfig | 16 +
drivers/mfd/Makefile | 1 +
drivers/mfd/hi6421-spmi-pmic.c | 311 ++++++++++++++++++
drivers/staging/Kconfig | 2 -
drivers/staging/Makefile | 1 -
drivers/staging/hikey9xx/Kconfig | 19 --
drivers/staging/hikey9xx/Makefile | 3 -
drivers/staging/hikey9xx/TODO | 5 -
drivers/staging/hikey9xx/hi6421-spmi-pmic.c | 311 ------------------
.../hikey9xx/hisilicon,hi6421-spmi-pmic.yaml | 134 --------
12 files changed, 469 insertions(+), 475 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
create mode 100644 drivers/mfd/hi6421-spmi-pmic.c
delete mode 100644 drivers/staging/hikey9xx/Kconfig
delete mode 100644 drivers/staging/hikey9xx/Makefile
delete mode 100644 drivers/staging/hikey9xx/TODO
delete mode 100644 drivers/staging/hikey9xx/hi6421-spmi-pmic.c
delete mode 100644 drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml
diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
new file mode 100644
index 000000000000..8e355cddd437
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/hisilicon,hi6421-spmi-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon 6421v600 SPMI PMIC
+
+maintainers:
+ - Mauro Carvalho Chehab <[email protected]>
+
+description: |
+ HiSilicon 6421v600 should be connected inside a MIPI System Power Management
+ (SPMI) bus. It provides interrupts and power supply.
+
+ The GPIO and interrupt settings are represented as part of the top-level PMIC
+ node.
+
+ The SPMI controller part is provided by
+ Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
+
+properties:
+ $nodename:
+ pattern: "pmic@[0-9a-f]"
+
+ compatible:
+ const: hisilicon,hi6421v600-spmi
+
+ reg:
+ maxItems: 1
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupt-controller: true
+
+ gpios:
+ maxItems: 1
+ description: GPIO used for IRQs
+
+ regulators:
+ type: object
+
+ properties:
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ patternProperties:
+ '^ldo[0-9]+@[0-9a-f]$':
+ type: object
+
+ $ref: "/schemas/regulator/regulator.yaml#"
+
+required:
+ - compatible
+ - reg
+ - regulators
+
+additionalProperties: false
+
+examples:
+ - |
+ /* pmic properties */
+
+ pmic: pmic@0 {
+ compatible = "hisilicon,hi6421-spmi";
+ reg = <0 0>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ gpios = <&gpio28 0 0>;
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-boot-on;
+ };
+
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-boot-on;
+ };
+
+ ldo9: LDO9 {
+ regulator-name = "ldo9";
+ regulator-min-microvolt = <1750000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo15: LDO15 {
+ regulator-name = "ldo15";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo16: LDO16 {
+ regulator-name = "ldo16";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ };
+
+ ldo17: LDO17 {
+ regulator-name = "ldo17";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo33: LDO33 {
+ regulator-name = "ldo33";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo34: LDO34 {
+ regulator-name = "ldo34";
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 9a69e3810964..89e84b050de6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8291,6 +8291,13 @@ S: Maintained
F: Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml
F: drivers/spmi/hisi-spmi-controller.c
+HISILICON SPMI PMIC DRIVER FOR HIKEY 6421v600
+M: Mauro Carvalho Chehab <[email protected]>
+L: [email protected]
+S: Maintained
+F: Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
+F: drivers/mfd/hi6421-spmi-pmic.c
+
HISILICON STAGING DRIVERS FOR HIKEY 960/970
M: Mauro Carvalho Chehab <[email protected]>
S: Maintained
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 5c7f2b100191..99b8da2548b5 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -509,6 +509,22 @@ config MFD_HI6421_PMIC
menus in order to enable them.
We communicate with the Hi6421 via memory-mapped I/O.
+config MFD_HI6421_SPMI
+ tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC"
+ depends on OF
+ depends on SPMI
+ select MFD_CORE
+ select REGMAP_SPMI
+ help
+ Add support for HiSilicon Hi6421v600 SPMI PMIC. Hi6421 includes
+ multi-functions, such as regulators, RTC, codec, Coulomb counter,
+ etc.
+
+ This driver includes core APIs _only_. You have to select
+ individual components like voltage regulators under corresponding
+ menus in order to enable them.
+ We communicate with the Hi6421v600 via a SPMI bus.
+
config MFD_HI655X_PMIC
tristate "HiSilicon Hi655X series PMU/Codec IC"
depends on ARCH_HISI || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 4f6d2b8a5f76..e87230fc61ac 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -232,6 +232,7 @@ obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o
obj-$(CONFIG_MFD_IQS62X) += iqs62x.o
obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o
obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o
+obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o
obj-$(CONFIG_MFD_HI655X_PMIC) += hi655x-pmic.o
obj-$(CONFIG_MFD_DLN2) += dln2.o
obj-$(CONFIG_MFD_RT5033) += rt5033.o
diff --git a/drivers/mfd/hi6421-spmi-pmic.c b/drivers/mfd/hi6421-spmi-pmic.c
new file mode 100644
index 000000000000..252b731e272d
--- /dev/null
+++ b/drivers/mfd/hi6421-spmi-pmic.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device driver for regulators in HISI PMIC IC
+ *
+ * Copyright (c) 2013- Linaro Ltd.
+ * Copyright (c) 2011- Hisilicon.
+ * Copyright (c) 2020- Huawei Technologies Co., Ltd
+ */
+
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/hi6421-spmi-pmic.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spmi.h>
+
+enum hi6421_spmi_pmic_irq_list {
+ OTMP = 0,
+ VBUS_CONNECT,
+ VBUS_DISCONNECT,
+ ALARMON_R,
+ HOLD_6S,
+ HOLD_1S,
+ POWERKEY_UP,
+ POWERKEY_DOWN,
+ OCP_SCP_R,
+ COUL_R,
+ SIM0_HPD_R,
+ SIM0_HPD_F,
+ SIM1_HPD_R,
+ SIM1_HPD_F,
+
+ PMIC_IRQ_LIST_MAX
+};
+
+#define HISI_IRQ_BANK_SIZE 2
+
+/*
+ * IRQ number for the power key button and mask for both UP and DOWN IRQs
+ */
+#define HISI_POWERKEY_IRQ_NUM 0
+#define HISI_IRQ_POWERKEY_UP_DOWN (BIT(POWERKEY_DOWN) | BIT(POWERKEY_UP))
+
+/*
+ * Registers for IRQ address and IRQ mask bits
+ *
+ * Please notice that we need to regmap a larger region, as other
+ * registers are used by the regulators.
+ * See drivers/regulator/hi6421-regulator.c.
+ */
+#define SOC_PMIC_IRQ_MASK_0_ADDR 0x0202
+#define SOC_PMIC_IRQ0_ADDR 0x0212
+
+/*
+ * The IRQs are mapped as:
+ *
+ * ====================== ============= ============ =====
+ * IRQ MASK REGISTER IRQ REGISTER BIT
+ * ====================== ============= ============ =====
+ * OTMP 0x0202 0x212 bit 0
+ * VBUS_CONNECT 0x0202 0x212 bit 1
+ * VBUS_DISCONNECT 0x0202 0x212 bit 2
+ * ALARMON_R 0x0202 0x212 bit 3
+ * HOLD_6S 0x0202 0x212 bit 4
+ * HOLD_1S 0x0202 0x212 bit 5
+ * POWERKEY_UP 0x0202 0x212 bit 6
+ * POWERKEY_DOWN 0x0202 0x212 bit 7
+ *
+ * OCP_SCP_R 0x0203 0x213 bit 0
+ * COUL_R 0x0203 0x213 bit 1
+ * SIM0_HPD_R 0x0203 0x213 bit 2
+ * SIM0_HPD_F 0x0203 0x213 bit 3
+ * SIM1_HPD_R 0x0203 0x213 bit 4
+ * SIM1_HPD_F 0x0203 0x213 bit 5
+ * ====================== ============= ============ =====
+ *
+ * Each mask register contains 8 bits. The ancillary macros below
+ * convert a number from 0 to 14 into a register address and a bit mask
+ */
+#define HISI_IRQ_MASK_REG(irq_data) (SOC_PMIC_IRQ_MASK_0_ADDR + \
+ (irqd_to_hwirq(irq_data) / BITS_PER_BYTE))
+#define HISI_IRQ_MASK_BIT(irq_data) BIT(irqd_to_hwirq(irq_data) & (BITS_PER_BYTE - 1))
+#define HISI_8BITS_MASK 0xff
+
+static const struct mfd_cell hi6421v600_devs[] = {
+ { .name = "hi6421v600-regulator", },
+};
+
+static irqreturn_t hi6421_spmi_irq_handler(int irq, void *priv)
+{
+ struct hi6421_spmi_pmic *ddata = (struct hi6421_spmi_pmic *)priv;
+ unsigned long pending;
+ unsigned int in;
+ int i, offset;
+
+ for (i = 0; i < HISI_IRQ_BANK_SIZE; i++) {
+ regmap_read(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, &in);
+
+ /* Mark pending IRQs as handled */
+ regmap_write(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, in);
+
+ pending = in & HISI_8BITS_MASK;
+
+ if (i == HISI_POWERKEY_IRQ_NUM &&
+ (pending & HISI_IRQ_POWERKEY_UP_DOWN) == HISI_IRQ_POWERKEY_UP_DOWN) {
+ /*
+ * If both powerkey down and up IRQs are received,
+ * handle them at the right order
+ */
+ generic_handle_irq(ddata->irqs[POWERKEY_DOWN]);
+ generic_handle_irq(ddata->irqs[POWERKEY_UP]);
+ pending &= ~HISI_IRQ_POWERKEY_UP_DOWN;
+ }
+
+ if (!pending)
+ continue;
+
+ for_each_set_bit(offset, &pending, BITS_PER_BYTE) {
+ generic_handle_irq(ddata->irqs[offset + i * BITS_PER_BYTE]);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void hi6421_spmi_irq_mask(struct irq_data *d)
+{
+ struct hi6421_spmi_pmic *ddata = irq_data_get_irq_chip_data(d);
+ unsigned long flags;
+ unsigned int data;
+ u32 offset;
+
+ offset = HISI_IRQ_MASK_REG(d);
+
+ spin_lock_irqsave(&ddata->lock, flags);
+
+ regmap_read(ddata->regmap, offset, &data);
+ data |= HISI_IRQ_MASK_BIT(d);
+ regmap_write(ddata->regmap, offset, data);
+
+ spin_unlock_irqrestore(&ddata->lock, flags);
+}
+
+static void hi6421_spmi_irq_unmask(struct irq_data *d)
+{
+ struct hi6421_spmi_pmic *ddata = irq_data_get_irq_chip_data(d);
+ u32 data, offset;
+ unsigned long flags;
+
+ offset = HISI_IRQ_MASK_REG(d);
+
+ spin_lock_irqsave(&ddata->lock, flags);
+
+ regmap_read(ddata->regmap, offset, &data);
+ data &= ~HISI_IRQ_MASK_BIT(d);
+ regmap_write(ddata->regmap, offset, data);
+
+ spin_unlock_irqrestore(&ddata->lock, flags);
+}
+
+static struct irq_chip hi6421_spmi_pmu_irqchip = {
+ .name = "hi6421v600-irq",
+ .irq_mask = hi6421_spmi_irq_mask,
+ .irq_unmask = hi6421_spmi_irq_unmask,
+ .irq_disable = hi6421_spmi_irq_mask,
+ .irq_enable = hi6421_spmi_irq_unmask,
+};
+
+static int hi6421_spmi_irq_map(struct irq_domain *d, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ struct hi6421_spmi_pmic *ddata = d->host_data;
+
+ irq_set_chip_and_handler_name(virq, &hi6421_spmi_pmu_irqchip,
+ handle_simple_irq, "hi6421v600");
+ irq_set_chip_data(virq, ddata);
+ irq_set_irq_type(virq, IRQ_TYPE_NONE);
+
+ return 0;
+}
+
+static const struct irq_domain_ops hi6421_spmi_domain_ops = {
+ .map = hi6421_spmi_irq_map,
+ .xlate = irq_domain_xlate_twocell,
+};
+
+static void hi6421_spmi_pmic_irq_init(struct hi6421_spmi_pmic *ddata)
+{
+ int i;
+ unsigned int pending;
+
+ /* Mask all IRQs */
+ for (i = 0; i < HISI_IRQ_BANK_SIZE; i++)
+ regmap_write(ddata->regmap, SOC_PMIC_IRQ_MASK_0_ADDR + i,
+ HISI_8BITS_MASK);
+
+ /* Mark all IRQs as handled */
+ for (i = 0; i < HISI_IRQ_BANK_SIZE; i++) {
+ regmap_read(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, &pending);
+ regmap_write(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i,
+ HISI_8BITS_MASK);
+ }
+}
+
+static const struct regmap_config regmap_config = {
+ .reg_bits = 16,
+ .val_bits = BITS_PER_BYTE,
+ .max_register = 0xffff,
+ .fast_io = true
+};
+
+static int hi6421_spmi_pmic_probe(struct spmi_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct hi6421_spmi_pmic *ddata;
+ unsigned int virq;
+ int ret, i;
+
+ ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
+ if (!ddata)
+ return -ENOMEM;
+
+ ddata->regmap = devm_regmap_init_spmi_ext(pdev, ®map_config);
+ if (IS_ERR(ddata->regmap))
+ return PTR_ERR(ddata->regmap);
+
+ spin_lock_init(&ddata->lock);
+
+ ddata->dev = dev;
+
+ ddata->gpio = of_get_gpio(np, 0);
+ if (ddata->gpio < 0)
+ return ddata->gpio;
+
+ if (!gpio_is_valid(ddata->gpio))
+ return -EINVAL;
+
+ ret = devm_gpio_request_one(dev, ddata->gpio, GPIOF_IN, "pmic");
+ if (ret < 0) {
+ dev_err(dev, "Failed to request gpio%d\n", ddata->gpio);
+ return ret;
+ }
+
+ ddata->irq = gpio_to_irq(ddata->gpio);
+
+ hi6421_spmi_pmic_irq_init(ddata);
+
+ ddata->irqs = devm_kzalloc(dev, PMIC_IRQ_LIST_MAX * sizeof(int), GFP_KERNEL);
+ if (!ddata->irqs)
+ return -ENOMEM;
+
+ ddata->domain = irq_domain_add_simple(np, PMIC_IRQ_LIST_MAX, 0,
+ &hi6421_spmi_domain_ops, ddata);
+ if (!ddata->domain) {
+ dev_err(dev, "Failed to create IRQ domain\n");
+ return -ENODEV;
+ }
+
+ for (i = 0; i < PMIC_IRQ_LIST_MAX; i++) {
+ virq = irq_create_mapping(ddata->domain, i);
+ if (!virq) {
+ dev_err(dev, "Failed to map H/W IRQ\n");
+ return -ENODEV;
+ }
+ ddata->irqs[i] = virq;
+ }
+
+ ret = devm_request_threaded_irq(dev,
+ ddata->irq, hi6421_spmi_irq_handler,
+ NULL,
+ IRQF_TRIGGER_LOW | IRQF_SHARED | IRQF_NO_SUSPEND,
+ "pmic", ddata);
+ if (ret < 0) {
+ dev_err(dev, "Failed to start IRQ handling thread: error %d\n",
+ ret);
+ return ret;
+ }
+
+ dev_set_drvdata(&pdev->dev, ddata);
+
+ ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
+ hi6421v600_devs, ARRAY_SIZE(hi6421v600_devs),
+ NULL, 0, NULL);
+ if (ret < 0)
+ dev_err(dev, "Failed to add child devices: %d\n", ret);
+
+ return ret;
+}
+
+static const struct of_device_id pmic_spmi_id_table[] = {
+ { .compatible = "hisilicon,hi6421-spmi" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pmic_spmi_id_table);
+
+static struct spmi_driver hi6421_spmi_pmic_driver = {
+ .driver = {
+ .name = "hi6421-spmi-pmic",
+ .of_match_table = pmic_spmi_id_table,
+ },
+ .probe = hi6421_spmi_pmic_probe,
+};
+module_spmi_driver(hi6421_spmi_pmic_driver);
+
+MODULE_DESCRIPTION("HiSilicon Hi6421v600 SPMI PMIC driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index b7ae5bdc4eb5..5b4267d3ed6b 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -104,6 +104,4 @@ source "drivers/staging/qlge/Kconfig"
source "drivers/staging/wfx/Kconfig"
-source "drivers/staging/hikey9xx/Kconfig"
-
endif # STAGING
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 075c979bfe7c..7179cdcaafe7 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -42,4 +42,3 @@ obj-$(CONFIG_FIELDBUS_DEV) += fieldbus/
obj-$(CONFIG_KPC2000) += kpc2000/
obj-$(CONFIG_QLGE) += qlge/
obj-$(CONFIG_WFX) += wfx/
-obj-y += hikey9xx/
diff --git a/drivers/staging/hikey9xx/Kconfig b/drivers/staging/hikey9xx/Kconfig
deleted file mode 100644
index 9f53df9068fe..000000000000
--- a/drivers/staging/hikey9xx/Kconfig
+++ /dev/null
@@ -1,19 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-
-# to be placed at drivers/mfd
-config MFD_HI6421_SPMI
- tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC"
- depends on HAS_IOMEM
- depends on OF
- depends on SPMI
- select MFD_CORE
- select REGMAP_SPMI
- help
- Add support for HiSilicon Hi6421v600 SPMI PMIC. Hi6421 includes
- multi-functions, such as regulators, RTC, codec, Coulomb counter,
- etc.
-
- This driver includes core APIs _only_. You have to select
- individual components like voltage regulators under corresponding
- menus in order to enable them.
- We communicate with the Hi6421v600 via a SPMI bus.
diff --git a/drivers/staging/hikey9xx/Makefile b/drivers/staging/hikey9xx/Makefile
deleted file mode 100644
index e3108d7dd849..000000000000
--- a/drivers/staging/hikey9xx/Makefile
+++ /dev/null
@@ -1,3 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-
-obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o
diff --git a/drivers/staging/hikey9xx/TODO b/drivers/staging/hikey9xx/TODO
deleted file mode 100644
index 65e7996a3066..000000000000
--- a/drivers/staging/hikey9xx/TODO
+++ /dev/null
@@ -1,5 +0,0 @@
-ToDo list:
-
-- Port other drivers needed by Hikey 960/970;
-- Test drivers on Hikey 960;
-- Validate device tree bindings.
diff --git a/drivers/staging/hikey9xx/hi6421-spmi-pmic.c b/drivers/staging/hikey9xx/hi6421-spmi-pmic.c
deleted file mode 100644
index 252b731e272d..000000000000
--- a/drivers/staging/hikey9xx/hi6421-spmi-pmic.c
+++ /dev/null
@@ -1,311 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device driver for regulators in HISI PMIC IC
- *
- * Copyright (c) 2013- Linaro Ltd.
- * Copyright (c) 2011- Hisilicon.
- * Copyright (c) 2020- Huawei Technologies Co., Ltd
- */
-
-#include <linux/bitops.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/mfd/core.h>
-#include <linux/mfd/hi6421-spmi-pmic.h>
-#include <linux/module.h>
-#include <linux/of_gpio.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/spmi.h>
-
-enum hi6421_spmi_pmic_irq_list {
- OTMP = 0,
- VBUS_CONNECT,
- VBUS_DISCONNECT,
- ALARMON_R,
- HOLD_6S,
- HOLD_1S,
- POWERKEY_UP,
- POWERKEY_DOWN,
- OCP_SCP_R,
- COUL_R,
- SIM0_HPD_R,
- SIM0_HPD_F,
- SIM1_HPD_R,
- SIM1_HPD_F,
-
- PMIC_IRQ_LIST_MAX
-};
-
-#define HISI_IRQ_BANK_SIZE 2
-
-/*
- * IRQ number for the power key button and mask for both UP and DOWN IRQs
- */
-#define HISI_POWERKEY_IRQ_NUM 0
-#define HISI_IRQ_POWERKEY_UP_DOWN (BIT(POWERKEY_DOWN) | BIT(POWERKEY_UP))
-
-/*
- * Registers for IRQ address and IRQ mask bits
- *
- * Please notice that we need to regmap a larger region, as other
- * registers are used by the regulators.
- * See drivers/regulator/hi6421-regulator.c.
- */
-#define SOC_PMIC_IRQ_MASK_0_ADDR 0x0202
-#define SOC_PMIC_IRQ0_ADDR 0x0212
-
-/*
- * The IRQs are mapped as:
- *
- * ====================== ============= ============ =====
- * IRQ MASK REGISTER IRQ REGISTER BIT
- * ====================== ============= ============ =====
- * OTMP 0x0202 0x212 bit 0
- * VBUS_CONNECT 0x0202 0x212 bit 1
- * VBUS_DISCONNECT 0x0202 0x212 bit 2
- * ALARMON_R 0x0202 0x212 bit 3
- * HOLD_6S 0x0202 0x212 bit 4
- * HOLD_1S 0x0202 0x212 bit 5
- * POWERKEY_UP 0x0202 0x212 bit 6
- * POWERKEY_DOWN 0x0202 0x212 bit 7
- *
- * OCP_SCP_R 0x0203 0x213 bit 0
- * COUL_R 0x0203 0x213 bit 1
- * SIM0_HPD_R 0x0203 0x213 bit 2
- * SIM0_HPD_F 0x0203 0x213 bit 3
- * SIM1_HPD_R 0x0203 0x213 bit 4
- * SIM1_HPD_F 0x0203 0x213 bit 5
- * ====================== ============= ============ =====
- *
- * Each mask register contains 8 bits. The ancillary macros below
- * convert a number from 0 to 14 into a register address and a bit mask
- */
-#define HISI_IRQ_MASK_REG(irq_data) (SOC_PMIC_IRQ_MASK_0_ADDR + \
- (irqd_to_hwirq(irq_data) / BITS_PER_BYTE))
-#define HISI_IRQ_MASK_BIT(irq_data) BIT(irqd_to_hwirq(irq_data) & (BITS_PER_BYTE - 1))
-#define HISI_8BITS_MASK 0xff
-
-static const struct mfd_cell hi6421v600_devs[] = {
- { .name = "hi6421v600-regulator", },
-};
-
-static irqreturn_t hi6421_spmi_irq_handler(int irq, void *priv)
-{
- struct hi6421_spmi_pmic *ddata = (struct hi6421_spmi_pmic *)priv;
- unsigned long pending;
- unsigned int in;
- int i, offset;
-
- for (i = 0; i < HISI_IRQ_BANK_SIZE; i++) {
- regmap_read(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, &in);
-
- /* Mark pending IRQs as handled */
- regmap_write(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, in);
-
- pending = in & HISI_8BITS_MASK;
-
- if (i == HISI_POWERKEY_IRQ_NUM &&
- (pending & HISI_IRQ_POWERKEY_UP_DOWN) == HISI_IRQ_POWERKEY_UP_DOWN) {
- /*
- * If both powerkey down and up IRQs are received,
- * handle them at the right order
- */
- generic_handle_irq(ddata->irqs[POWERKEY_DOWN]);
- generic_handle_irq(ddata->irqs[POWERKEY_UP]);
- pending &= ~HISI_IRQ_POWERKEY_UP_DOWN;
- }
-
- if (!pending)
- continue;
-
- for_each_set_bit(offset, &pending, BITS_PER_BYTE) {
- generic_handle_irq(ddata->irqs[offset + i * BITS_PER_BYTE]);
- }
- }
-
- return IRQ_HANDLED;
-}
-
-static void hi6421_spmi_irq_mask(struct irq_data *d)
-{
- struct hi6421_spmi_pmic *ddata = irq_data_get_irq_chip_data(d);
- unsigned long flags;
- unsigned int data;
- u32 offset;
-
- offset = HISI_IRQ_MASK_REG(d);
-
- spin_lock_irqsave(&ddata->lock, flags);
-
- regmap_read(ddata->regmap, offset, &data);
- data |= HISI_IRQ_MASK_BIT(d);
- regmap_write(ddata->regmap, offset, data);
-
- spin_unlock_irqrestore(&ddata->lock, flags);
-}
-
-static void hi6421_spmi_irq_unmask(struct irq_data *d)
-{
- struct hi6421_spmi_pmic *ddata = irq_data_get_irq_chip_data(d);
- u32 data, offset;
- unsigned long flags;
-
- offset = HISI_IRQ_MASK_REG(d);
-
- spin_lock_irqsave(&ddata->lock, flags);
-
- regmap_read(ddata->regmap, offset, &data);
- data &= ~HISI_IRQ_MASK_BIT(d);
- regmap_write(ddata->regmap, offset, data);
-
- spin_unlock_irqrestore(&ddata->lock, flags);
-}
-
-static struct irq_chip hi6421_spmi_pmu_irqchip = {
- .name = "hi6421v600-irq",
- .irq_mask = hi6421_spmi_irq_mask,
- .irq_unmask = hi6421_spmi_irq_unmask,
- .irq_disable = hi6421_spmi_irq_mask,
- .irq_enable = hi6421_spmi_irq_unmask,
-};
-
-static int hi6421_spmi_irq_map(struct irq_domain *d, unsigned int virq,
- irq_hw_number_t hw)
-{
- struct hi6421_spmi_pmic *ddata = d->host_data;
-
- irq_set_chip_and_handler_name(virq, &hi6421_spmi_pmu_irqchip,
- handle_simple_irq, "hi6421v600");
- irq_set_chip_data(virq, ddata);
- irq_set_irq_type(virq, IRQ_TYPE_NONE);
-
- return 0;
-}
-
-static const struct irq_domain_ops hi6421_spmi_domain_ops = {
- .map = hi6421_spmi_irq_map,
- .xlate = irq_domain_xlate_twocell,
-};
-
-static void hi6421_spmi_pmic_irq_init(struct hi6421_spmi_pmic *ddata)
-{
- int i;
- unsigned int pending;
-
- /* Mask all IRQs */
- for (i = 0; i < HISI_IRQ_BANK_SIZE; i++)
- regmap_write(ddata->regmap, SOC_PMIC_IRQ_MASK_0_ADDR + i,
- HISI_8BITS_MASK);
-
- /* Mark all IRQs as handled */
- for (i = 0; i < HISI_IRQ_BANK_SIZE; i++) {
- regmap_read(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, &pending);
- regmap_write(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i,
- HISI_8BITS_MASK);
- }
-}
-
-static const struct regmap_config regmap_config = {
- .reg_bits = 16,
- .val_bits = BITS_PER_BYTE,
- .max_register = 0xffff,
- .fast_io = true
-};
-
-static int hi6421_spmi_pmic_probe(struct spmi_device *pdev)
-{
- struct device *dev = &pdev->dev;
- struct device_node *np = dev->of_node;
- struct hi6421_spmi_pmic *ddata;
- unsigned int virq;
- int ret, i;
-
- ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
- if (!ddata)
- return -ENOMEM;
-
- ddata->regmap = devm_regmap_init_spmi_ext(pdev, ®map_config);
- if (IS_ERR(ddata->regmap))
- return PTR_ERR(ddata->regmap);
-
- spin_lock_init(&ddata->lock);
-
- ddata->dev = dev;
-
- ddata->gpio = of_get_gpio(np, 0);
- if (ddata->gpio < 0)
- return ddata->gpio;
-
- if (!gpio_is_valid(ddata->gpio))
- return -EINVAL;
-
- ret = devm_gpio_request_one(dev, ddata->gpio, GPIOF_IN, "pmic");
- if (ret < 0) {
- dev_err(dev, "Failed to request gpio%d\n", ddata->gpio);
- return ret;
- }
-
- ddata->irq = gpio_to_irq(ddata->gpio);
-
- hi6421_spmi_pmic_irq_init(ddata);
-
- ddata->irqs = devm_kzalloc(dev, PMIC_IRQ_LIST_MAX * sizeof(int), GFP_KERNEL);
- if (!ddata->irqs)
- return -ENOMEM;
-
- ddata->domain = irq_domain_add_simple(np, PMIC_IRQ_LIST_MAX, 0,
- &hi6421_spmi_domain_ops, ddata);
- if (!ddata->domain) {
- dev_err(dev, "Failed to create IRQ domain\n");
- return -ENODEV;
- }
-
- for (i = 0; i < PMIC_IRQ_LIST_MAX; i++) {
- virq = irq_create_mapping(ddata->domain, i);
- if (!virq) {
- dev_err(dev, "Failed to map H/W IRQ\n");
- return -ENODEV;
- }
- ddata->irqs[i] = virq;
- }
-
- ret = devm_request_threaded_irq(dev,
- ddata->irq, hi6421_spmi_irq_handler,
- NULL,
- IRQF_TRIGGER_LOW | IRQF_SHARED | IRQF_NO_SUSPEND,
- "pmic", ddata);
- if (ret < 0) {
- dev_err(dev, "Failed to start IRQ handling thread: error %d\n",
- ret);
- return ret;
- }
-
- dev_set_drvdata(&pdev->dev, ddata);
-
- ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
- hi6421v600_devs, ARRAY_SIZE(hi6421v600_devs),
- NULL, 0, NULL);
- if (ret < 0)
- dev_err(dev, "Failed to add child devices: %d\n", ret);
-
- return ret;
-}
-
-static const struct of_device_id pmic_spmi_id_table[] = {
- { .compatible = "hisilicon,hi6421-spmi" },
- { }
-};
-MODULE_DEVICE_TABLE(of, pmic_spmi_id_table);
-
-static struct spmi_driver hi6421_spmi_pmic_driver = {
- .driver = {
- .name = "hi6421-spmi-pmic",
- .of_match_table = pmic_spmi_id_table,
- },
- .probe = hi6421_spmi_pmic_probe,
-};
-module_spmi_driver(hi6421_spmi_pmic_driver);
-
-MODULE_DESCRIPTION("HiSilicon Hi6421v600 SPMI PMIC driver");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml b/drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml
deleted file mode 100644
index 8e355cddd437..000000000000
--- a/drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml
+++ /dev/null
@@ -1,134 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/mfd/hisilicon,hi6421-spmi-pmic.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: HiSilicon 6421v600 SPMI PMIC
-
-maintainers:
- - Mauro Carvalho Chehab <[email protected]>
-
-description: |
- HiSilicon 6421v600 should be connected inside a MIPI System Power Management
- (SPMI) bus. It provides interrupts and power supply.
-
- The GPIO and interrupt settings are represented as part of the top-level PMIC
- node.
-
- The SPMI controller part is provided by
- Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
-
-properties:
- $nodename:
- pattern: "pmic@[0-9a-f]"
-
- compatible:
- const: hisilicon,hi6421v600-spmi
-
- reg:
- maxItems: 1
-
- '#interrupt-cells':
- const: 2
-
- interrupt-controller: true
-
- gpios:
- maxItems: 1
- description: GPIO used for IRQs
-
- regulators:
- type: object
-
- properties:
- '#address-cells':
- const: 1
-
- '#size-cells':
- const: 0
-
- patternProperties:
- '^ldo[0-9]+@[0-9a-f]$':
- type: object
-
- $ref: "/schemas/regulator/regulator.yaml#"
-
-required:
- - compatible
- - reg
- - regulators
-
-additionalProperties: false
-
-examples:
- - |
- /* pmic properties */
-
- pmic: pmic@0 {
- compatible = "hisilicon,hi6421-spmi";
- reg = <0 0>;
-
- #interrupt-cells = <2>;
- interrupt-controller;
- gpios = <&gpio28 0 0>;
-
- regulators {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ldo3: LDO3 {
- regulator-name = "ldo3";
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <2000000>;
- regulator-boot-on;
- };
-
- ldo4: LDO4 {
- regulator-name = "ldo4";
- regulator-min-microvolt = <1725000>;
- regulator-max-microvolt = <1900000>;
- regulator-boot-on;
- };
-
- ldo9: LDO9 {
- regulator-name = "ldo9";
- regulator-min-microvolt = <1750000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
-
- ldo15: LDO15 {
- regulator-name = "ldo15";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- };
-
- ldo16: LDO16 {
- regulator-name = "ldo16";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3000000>;
- regulator-boot-on;
- };
-
- ldo17: LDO17 {
- regulator-name = "ldo17";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo33: LDO33 {
- regulator-name = "ldo33";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
-
- ldo34: LDO34 {
- regulator-name = "ldo34";
- regulator-min-microvolt = <2600000>;
- regulator-max-microvolt = <3300000>;
- };
- };
- };
--
2.31.1
On Thu, Jun 24, 2021 at 04:01:29PM +0200, Mauro Carvalho Chehab wrote:
> Hi Greg,
>
> Those are the remaining patches that are needed for the USB to work
> with Hikey970.
>
> This series address the comments made on v5. Sorry for taking so long to
> return back on this. Got sidetracked by other unrelated stuff.
I took the first 2 patches in here.
thanks,
greg k-h