As requested by Rob Herring, this series split the PHY part into a separate driver.
Then, it adds support for Kirin 970 on a single patch.
With this change, the PHY-specific device tree bindings for Kirin 960 moved
to its own PHY properties.
Tested on Hikey970:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3670 (rev 01)
01:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:01.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:04.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:05.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
02:09.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)
$ ethtool enp6s0
Settings for enp6s0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
netlink error: Operation not permitted
Link detected: yes
Partially tested on Hikey 960[1]:
$ lspci
00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3660 (rev 01)
[1] The Hikey 960 doesn't come with any internal PCIe device.
Its hardware supports just an external device via a M.2 slot that
doesn't support SATA. I ordered a NVMe device to test, but the vendor
is currently out of supply. It should take 3-4 weeks to arrive here. I'll
run an extra test on it once it arrives.
---
v5:
- added "static" to hi3670_pcie_get_eyeparam() declaration on patch 6/8
v4:
- dropped the DTS patch, as it depends on a PMIC-related patch series;
- minor changes at the patch description;
- HiKey and HiSilicon are now using the preferred CamelCase format.
Mauro Carvalho Chehab (8):
dt-bindings: phy: Add bindings for HiKey 960 PCIe PHY
dt-bindings: phy: Add bindings for HiKey 970 PCIe PHY
dt-bindings: PCI: kirin: Fix compatible string
dt-bindings: PCI: kirin: Drop PHY properties
phy: HiSilicon: Add driver for Kirin 960 PCIe PHY
phy: HiSilicon: add driver for Kirin 970 PCIe PHY
PCI: kirin: Drop the PHY logic from the driver
PCI: kirin: Use regmap for APB registers
.../devicetree/bindings/pci/kirin-pcie.txt | 21 +-
.../phy/hisilicon,phy-hi3660-pcie.yaml | 82 ++
.../phy/hisilicon,phy-hi3670-pcie.yaml | 101 ++
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 29 +-
drivers/pci/controller/dwc/pcie-kirin.c | 298 ++----
drivers/phy/hisilicon/Kconfig | 20 +
drivers/phy/hisilicon/Makefile | 2 +
drivers/phy/hisilicon/phy-hi3660-pcie.c | 325 +++++++
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
9 files changed, 1500 insertions(+), 270 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3660-pcie.yaml
create mode 100644 Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml
create mode 100644 drivers/phy/hisilicon/phy-hi3660-pcie.c
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
--
2.31.1
The Kirin 970 PHY is somewhat similar to the Kirin 960, but it
does a lot more. Add the needed bits for PCIe to start working on
HiKey 970 boards.
Co-developed-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
---
.../devicetree/bindings/pci/kirin-pcie.txt | 1 +
drivers/pci/controller/dwc/pcie-kirin.c | 1 +
drivers/phy/hisilicon/Kconfig | 10 +
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hi3670-pcie.c | 892 ++++++++++++++++++
5 files changed, 905 insertions(+)
create mode 100644 drivers/phy/hisilicon/phy-hi3670-pcie.c
diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
index a93a8cfa1afb..585aadfeafd1 100644
--- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt
@@ -10,6 +10,7 @@ Additional properties are described here:
Required properties
- compatible:
"hisilicon,kirin960-pcie"
+ "hisilicon,kirin970-pcie"
- reg: Should contain rc_dbi, apb, config registers location and length.
- reg-names: Must include the following entries:
"dbi": controller configuration registers;
diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
index 026fd1e42a55..7b0f87535960 100644
--- a/drivers/pci/controller/dwc/pcie-kirin.c
+++ b/drivers/pci/controller/dwc/pcie-kirin.c
@@ -472,6 +472,7 @@ static int kirin_pcie_probe(struct platform_device *pdev)
static const struct of_device_id kirin_pcie_match[] = {
{ .compatible = "hisilicon,kirin960-pcie" },
+ { .compatible = "hisilicon,kirin970-pcie" },
{},
};
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index 30b7f1187965..65e0ff6e85ad 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -43,6 +43,16 @@ config PHY_HI3670_USB
To compile this driver as a module, choose M here.
+config PHY_HI3670_PCIE
+ tristate "hi3670 PCIe PHY support"
+ depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the HiSilicon hi3670 PCIe PHY.
+
+ To compile this driver as a module, choose M here.
+
config PHY_HISTB_COMBPHY
tristate "HiSilicon STB SoCs COMBPHY support"
depends on (ARCH_HISI && ARM64) || COMPILE_TEST
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index 3c3d70dd7469..2670f2f382e1 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
obj-$(CONFIG_PHY_HI3660_USB) += phy-hi3660-usb3.o
obj-$(CONFIG_PHY_HI3660_PCIE) += phy-hi3660-pcie.o
obj-$(CONFIG_PHY_HI3670_USB) += phy-hi3670-usb3.o
+obj-$(CONFIG_PHY_HI3670_PCIE) += phy-hi3670-pcie.o
obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o
obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
diff --git a/drivers/phy/hisilicon/phy-hi3670-pcie.c b/drivers/phy/hisilicon/phy-hi3670-pcie.c
new file mode 100644
index 000000000000..3e3a15d9006d
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi3670-pcie.c
@@ -0,0 +1,892 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe phy driver for Kirin 970
+ *
+ * Copyright (C) 2017 HiSilicon Electronics Co., Ltd.
+ * https://www.huawei.com
+ * Copyright (C) 2021 Huawei Technologies Co., Ltd.
+ * https://www.huawei.com
+ *
+ * Authors:
+ * Mauro Carvalho Chehab <[email protected]>
+ * Manivannan Sadhasivam <[email protected]>
+ *
+ * Based on:
+ * https://lore.kernel.org/lkml/4c9d6581478aa966698758c0420933f5defab4dd.1612335031.git.mchehab+huawei@kernel.org/
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define AXI_CLK_FREQ 207500000
+#define REF_CLK_FREQ 100000000
+
+/* PCIe CTRL registers */
+#define SOC_PCIECTRL_CTRL0_ADDR 0x000
+#define SOC_PCIECTRL_CTRL1_ADDR 0x004
+#define SOC_PCIECTRL_CTRL7_ADDR 0x01c
+#define SOC_PCIECTRL_CTRL12_ADDR 0x030
+#define SOC_PCIECTRL_CTRL20_ADDR 0x050
+#define SOC_PCIECTRL_CTRL21_ADDR 0x054
+#define SOC_PCIECTRL_STATE0_ADDR 0x400
+
+/* PCIe PHY registers */
+#define SOC_PCIEPHY_CTRL0_ADDR 0x000
+#define SOC_PCIEPHY_CTRL1_ADDR 0x004
+#define SOC_PCIEPHY_CTRL2_ADDR 0x008
+#define SOC_PCIEPHY_CTRL3_ADDR 0x00c
+#define SOC_PCIEPHY_CTRL38_ADDR 0x0098
+#define SOC_PCIEPHY_STATE0_ADDR 0x400
+
+#define PCIE_LINKUP_ENABLE (0x8020)
+#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21)
+#define PCIE_LTSSM_ENABLE_BIT (0x1 << 11)
+#define PCIEPHY_RESET_BIT (0x1 << 17)
+#define PCIEPHY_PIPE_LINE0_RESET_BIT (0x1 << 19)
+
+#define PORT_MSI_CTRL_ADDR 0x820
+#define PORT_MSI_CTRL_UPPER_ADDR 0x824
+#define PORT_MSI_CTRL_INT0_ENABLE 0x828
+
+#define EYEPARAM_NOCFG 0xFFFFFFFF
+#define RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1 0x3001
+#define SUP_DIG_LVL_OVRD_IN 0xf
+#define LANEN_DIG_ASIC_TX_OVRD_IN_1 0x1002
+#define LANEN_DIG_ASIC_TX_OVRD_IN_2 0x1003
+
+/* hi3670 pciephy register */
+#define SOC_PCIEPHY_MMC1PLL_CTRL1 0xc04
+#define SOC_PCIEPHY_MMC1PLL_CTRL16 0xC40
+#define SOC_PCIEPHY_MMC1PLL_CTRL17 0xC44
+#define SOC_PCIEPHY_MMC1PLL_CTRL20 0xC50
+#define SOC_PCIEPHY_MMC1PLL_CTRL21 0xC54
+#define SOC_PCIEPHY_MMC1PLL_STAT0 0xE00
+
+#define CRGPERIPH_PEREN12 0x470
+#define CRGPERIPH_PERDIS12 0x474
+#define CRGPERIPH_PCIECTRL0 0x800
+
+/* define ie,oe cfg */
+#define IO_IE_EN_HARD_BYPASS (0x1 << 27)
+#define IO_OE_EN_HARD_BYPASS (0x1 << 11)
+#define IO_HARD_CTRL_DEBOUNCE_BYPASS (0x1 << 10)
+#define IO_OE_GT_MODE (0x2 << 7)
+#define DEBOUNCE_WAITCFG_IN (0xf << 20)
+#define DEBOUNCE_WAITCFG_OUT (0xf << 13)
+
+/* noc power domain */
+#define NOC_POWER_IDLEREQ_1 0x38c
+#define NOC_POWER_IDLE_1 0x394
+#define NOC_PW_MASK 0x10000
+#define NOC_PW_SET_BIT 0x1
+
+/* Number of GPIOs required by PHY */
+#define MAX_GPIO_RESETS 4
+#define MAX_GPIO_CLKREQ 3
+#define NUM_EYEPARAM 5
+
+/* info located in sysctrl */
+#define SCTRL_PCIE_CMOS_OFFSET 0x60
+#define SCTRL_PCIE_CMOS_BIT 0x10
+#define SCTRL_PCIE_ISO_OFFSET 0x44
+#define SCTRL_PCIE_ISO_BIT 0x30
+#define SCTRL_PCIE_HPCLK_OFFSET 0x190
+#define SCTRL_PCIE_HPCLK_BIT 0x184000
+#define SCTRL_PCIE_OE_OFFSET 0x14a
+#define PCIE_DEBOUNCE_PARAM 0xF0F400
+#define PCIE_OE_BYPASS (0x3 << 28)
+
+/* peri_crg ctrl */
+#define CRGCTRL_PCIE_ASSERT_OFFSET 0x88
+#define CRGCTRL_PCIE_ASSERT_BIT 0x8c000000
+
+/* Time for delay */
+#define REF_2_PERST_MIN 20000
+#define REF_2_PERST_MAX 25000
+#define PERST_2_ACCESS_MIN 10000
+#define PERST_2_ACCESS_MAX 12000
+#define PIPE_CLK_WAIT_MIN 550
+#define PIPE_CLK_WAIT_MAX 600
+#define TIME_CMOS_MIN 100
+#define TIME_CMOS_MAX 105
+#define TIME_PHY_PD_MIN 10
+#define TIME_PHY_PD_MAX 11
+
+struct hi3670_pcie_phy {
+ struct device *dev;
+ void __iomem *base;
+ struct regmap *apb;
+ struct regmap *crgctrl;
+ struct regmap *sysctrl;
+ struct regmap *pmctrl;
+ struct clk *apb_sys_clk;
+ struct clk *apb_phy_clk;
+ struct clk *phy_ref_clk;
+ struct clk *pcie_aclk;
+ struct clk *pcie_aux_clk;
+ int n_gpio_resets;
+ int n_gpio_clkreq;
+ int gpio_id_reset[MAX_GPIO_RESETS];
+ const char *reset_names[MAX_GPIO_RESETS];
+ int gpio_id_clkreq[MAX_GPIO_CLKREQ];
+ const char *clkreq_names[MAX_GPIO_CLKREQ];
+ u32 eye_param[NUM_EYEPARAM];
+};
+
+
+/* Registers in PCIePHY */
+static inline void hi3670_apb_phy_writel(struct hi3670_pcie_phy *phy,
+ u32 val, u32 reg)
+{
+ writel(val, phy->base + 0x40000 + reg);
+}
+
+static inline u32 hi3670_apb_phy_readl(struct hi3670_pcie_phy *phy, u32 reg)
+{
+ return readl(phy->base + 0x40000 + reg);
+}
+
+static inline void kirin_apb_natural_phy_writel(struct hi3670_pcie_phy *phy,
+ u32 val, u32 reg)
+{
+ writel(val, phy->base + reg * 4);
+}
+
+static inline u32 kirin_apb_natural_phy_readl(struct hi3670_pcie_phy *phy,
+ u32 reg)
+{
+ return readl(phy->base + reg * 4);
+}
+
+static void hi3670_pcie_phy_oe_enable(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ regmap_read(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, &val);
+ val |= PCIE_DEBOUNCE_PARAM;
+ val &= ~PCIE_OE_BYPASS;
+ regmap_write(phy->sysctrl, SCTRL_PCIE_OE_OFFSET, val);
+}
+
+static void hi3670_pcie_get_eyeparam(struct hi3670_pcie_phy *phy)
+{
+ struct device *dev = phy->dev;
+ struct device_node *np;
+ int ret, i;
+
+ np = dev->of_node;
+
+ ret = of_property_read_u32_array(np, "hisilicon,eye-diagram-param",
+ phy->eye_param, NUM_EYEPARAM);
+ if (!ret)
+ return;
+
+ /* There's no optional eye_param property. Set array to default */
+ for (i = 0; i < NUM_EYEPARAM; i++)
+ phy->eye_param[i] = EYEPARAM_NOCFG;
+}
+
+static void hi3670_pcie_set_eyeparam(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ val = kirin_apb_natural_phy_readl(phy, RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1);
+
+ if (phy->eye_param[1] != EYEPARAM_NOCFG) {
+ val &= (~0xf00);
+ val |= (phy->eye_param[1] << 8) | (0x1 << 12);
+ }
+ kirin_apb_natural_phy_writel(phy, val, RAWLANEN_DIG_PCS_XF_TX_OVRD_IN_1);
+
+ val = kirin_apb_natural_phy_readl(phy, LANEN_DIG_ASIC_TX_OVRD_IN_2);
+ val &= (~0x1FBF);
+ if (phy->eye_param[2] != EYEPARAM_NOCFG)
+ val |= (phy->eye_param[2]<< 0) | (0x1 << 6);
+
+ if (phy->eye_param[3] != EYEPARAM_NOCFG)
+ val |= (phy->eye_param[3] << 7) | (0x1 << 13);
+
+ kirin_apb_natural_phy_writel(phy, val, LANEN_DIG_ASIC_TX_OVRD_IN_2);
+
+ val = kirin_apb_natural_phy_readl(phy, SUP_DIG_LVL_OVRD_IN);
+ if (phy->eye_param[0] != EYEPARAM_NOCFG) {
+ val &= (~0x1C0);
+ val |= (phy->eye_param[0] << 6) | (0x1 << 9);
+ }
+ kirin_apb_natural_phy_writel(phy, val, SUP_DIG_LVL_OVRD_IN);
+
+ val = kirin_apb_natural_phy_readl(phy, LANEN_DIG_ASIC_TX_OVRD_IN_1);
+ if (phy->eye_param[4] != EYEPARAM_NOCFG) {
+ val &= (~0x7E00);
+ val |= (phy->eye_param[4] << 9) | (0x1 << 15);
+ }
+ kirin_apb_natural_phy_writel(phy, val, LANEN_DIG_ASIC_TX_OVRD_IN_1);
+}
+
+static int hi3670_pcie_gpio_request(struct hi3670_pcie_phy *phy,
+ struct device *dev)
+{
+ int ret, i;
+
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ if (!gpio_is_valid(phy->gpio_id_reset[i])) {
+ dev_err(dev, "unable to get a valid %s gpio\n",
+ phy->reset_names[i]);
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, phy->gpio_id_reset[i],
+ phy->reset_names[i]);
+ if (ret)
+ return ret;
+ }
+
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ if (!gpio_is_valid(phy->gpio_id_clkreq[i])) {
+ dev_err(dev, "unable to get a valid %s gpio\n",
+ phy->clkreq_names[i]);
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, phy->gpio_id_clkreq[i],
+ phy->clkreq_names[i]);
+ if (ret)
+ return ret;
+ }
+
+ return ret;
+}
+
+static void hi3670_pcie_natural_cfg(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ /* change 2p mem_ctrl */
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL20_ADDR, 0x02605550);
+
+ /* pull up sys_aux_pwr_det */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL7_ADDR, &val);
+ val |= (0x1 << 10);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL7_ADDR, val);
+
+ /* output, pull down */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, &val);
+ val &= ~(0x3 << 2);
+ val |= (0x1 << 1);
+ val &= ~(0x1 << 0);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, val);
+
+ /* Handle phy_reset and lane0_reset to HW */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL1_ADDR);
+ val |= PCIEPHY_RESET_BIT;
+ val &= ~PCIEPHY_PIPE_LINE0_RESET_BIT;
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL1_ADDR);
+
+ /* fix chip bug: TxDetectRx fail */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL38_ADDR);
+ val |= (0x1 << 2);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL38_ADDR);
+}
+
+static void hi3670_pcie_pll_init(struct hi3670_pcie_phy *phy)
+{
+ u32 val;
+
+ /* choose FNPLL */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL1);
+ val |= (0x1 << 27);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL1);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val &= 0xF000FFFF;
+ /* fnpll fbdiv = 0xD0 */
+ val |= (0xd0 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL17);
+ val &= 0xFF000000;
+ /* fnpll fracdiv = 0x555555 */
+ val |= (0x555555 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL17);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val &= 0xF5FF88FF;
+ /* fnpll dll_en = 0x1 */
+ val |= (0x1 << 27);
+ /* fnpll postdiv1 = 0x5 */
+ val |= (0x5 << 8);
+ /* fnpll postdiv2 = 0x4 */
+ val |= (0x4 << 12);
+ /* fnpll pll_mode = 0x0 */
+ val &= ~(0x1 << 25);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+
+ hi3670_apb_phy_writel(phy, 0x20, SOC_PCIEPHY_MMC1PLL_CTRL21);
+}
+
+static int hi3670_pcie_pll_ctrl(struct hi3670_pcie_phy *phy, bool enable)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ int time = 200;
+
+ if (enable) {
+ /* pd = 0 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val &= ~(0x1 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_STAT0);
+
+ /* choose FNPLL */
+ while (!(val & 0x10)) {
+ if (!time) {
+ dev_err(dev, "wait for pll_lock timeout\n");
+ return -1;
+ }
+ time --;
+ udelay(1);
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_STAT0);
+ }
+
+ /* pciepll_bp = 0 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val &= ~(0x1 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+
+ } else {
+ /* pd = 1 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL16);
+ val |= (0x1 << 0);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL16);
+
+ /* pciepll_bp = 1 */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ val |= (0x1 << 16);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_MMC1PLL_CTRL20);
+ }
+
+ return 0;
+}
+
+static void hi3670_pcie_hp_debounce_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ if (open)
+ /* gt_clk_pcie_hp/gt_clk_pcie_debounce open */
+ regmap_write(phy->crgctrl, CRGPERIPH_PEREN12, 0x9000);
+ else
+ /* gt_clk_pcie_hp/gt_clk_pcie_debounce close */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x9000);
+}
+
+static void hi3670_pcie_phyref_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ unsigned int val;
+
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+
+ if (open)
+ val &= ~(0x1 << 1); //enable hard gt mode
+ else
+ val |= (0x1 << 1); //disable hard gt mode
+
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x4000);
+}
+
+static void hi3670_pcie_oe_ctrl(struct hi3670_pcie_phy *phy, bool en_flag)
+{
+ unsigned int val;
+
+ regmap_read(phy->crgctrl , CRGPERIPH_PCIECTRL0, &val);
+
+ /* set ie cfg */
+ val |= IO_IE_EN_HARD_BYPASS;
+
+ /* set oe cfg */
+ val &= ~IO_HARD_CTRL_DEBOUNCE_BYPASS;
+
+ /* set phy_debounce in&out time */
+ val |= (DEBOUNCE_WAITCFG_IN | DEBOUNCE_WAITCFG_OUT);
+
+ /* select oe_gt_mode */
+ val |= IO_OE_GT_MODE;
+
+ if (en_flag)
+ val &= ~IO_OE_EN_HARD_BYPASS;
+ else
+ val |= IO_OE_EN_HARD_BYPASS;
+
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+}
+
+static void hi3670_pcie_ioref_gt(struct hi3670_pcie_phy *phy, bool open)
+{
+ unsigned int val;
+
+ if (open) {
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL21_ADDR, 0x20000070);
+
+ hi3670_pcie_oe_ctrl(phy, true);
+
+ /* en hard gt mode */
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+ val &= ~(0x1 << 0);
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x2000);
+
+ } else {
+ /* disable hard gt mode */
+ regmap_read(phy->crgctrl, CRGPERIPH_PCIECTRL0, &val);
+ val |= (0x1 << 0);
+ regmap_write(phy->crgctrl, CRGPERIPH_PCIECTRL0, val);
+
+ /* disable soft gt mode */
+ regmap_write(phy->crgctrl, CRGPERIPH_PERDIS12, 0x2000);
+
+ hi3670_pcie_oe_ctrl(phy, false);
+ }
+}
+
+static int hi3670_pcie_allclk_ctrl(struct hi3670_pcie_phy *phy, bool clk_on)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ int ret = 0;
+
+ if (!clk_on)
+ goto close_clocks;
+
+ /* choose 100MHz clk src: Bit[8]==1 pad, Bit[8]==0 pll */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL1_ADDR);
+ val &= ~(0x1 << 8);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL1_ADDR);
+
+ hi3670_pcie_pll_init(phy);
+
+ ret = hi3670_pcie_pll_ctrl(phy, true);
+ if (ret) {
+ dev_err(dev, "Failed to enable pll\n");
+ return -1;
+ }
+ hi3670_pcie_hp_debounce_gt(phy, true);
+ hi3670_pcie_phyref_gt(phy, true);
+ hi3670_pcie_ioref_gt(phy, true);
+
+ ret = clk_set_rate(phy->pcie_aclk, AXI_CLK_FREQ);
+ if (ret) {
+ dev_err(dev, "Failed to set rate\n");
+ goto close_clocks;
+ }
+
+ return 0;
+
+close_clocks:
+ hi3670_pcie_ioref_gt(phy, false);
+ hi3670_pcie_phyref_gt(phy, false);
+ hi3670_pcie_hp_debounce_gt(phy, false);
+
+ hi3670_pcie_pll_ctrl(phy, false);
+
+ return ret;
+}
+
+static bool is_pipe_clk_stable(struct hi3670_pcie_phy *phy)
+{
+ struct device *dev = phy->dev;
+ u32 val;
+ u32 time = 100;
+ u32 pipe_clk_stable = 0x1 << 19;
+
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_STATE0_ADDR);
+ while (val & pipe_clk_stable) {
+ mdelay(1);
+ if (time == 0) {
+ dev_err(dev, "PIPE clk is not stable\n");
+ return false;
+ }
+ time--;
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_STATE0_ADDR);
+ }
+
+ return true;
+}
+
+static int hi3670_pcie_noc_power(struct hi3670_pcie_phy *phy, bool enable)
+{
+ struct device *dev = phy->dev;
+ u32 time = 100;
+ unsigned int val = NOC_PW_MASK;
+ int rst;
+
+ if (enable)
+ val = NOC_PW_MASK | NOC_PW_SET_BIT;
+ else
+ val = NOC_PW_MASK;
+ rst = enable ? 1 : 0;
+
+ regmap_write(phy->pmctrl, NOC_POWER_IDLEREQ_1, val);
+
+ time = 100;
+ regmap_read(phy->pmctrl, NOC_POWER_IDLE_1, &val);
+ while((val & NOC_PW_SET_BIT) != rst) {
+ udelay(10);
+ if (!time) {
+ dev_err(dev, "Failed to reverse noc power-status\n");
+ return -1;
+ }
+ time--;
+ regmap_read(phy->pmctrl, NOC_POWER_IDLE_1, &val);
+ }
+
+ return 0;
+}
+
+static int hi3670_pcie_get_apb(struct hi3670_pcie_phy *phy)
+{
+ struct device_node *pcie_port;
+ struct device *dev = phy->dev;
+ struct device *pcie_dev;
+
+ pcie_port = of_get_child_by_name(dev->parent->of_node, "pcie");
+ if (!pcie_port) {
+ dev_err(dev, "no pcie node found in %s\n",
+ dev->parent->of_node->full_name);
+ return -ENODEV;
+ }
+
+ pcie_dev = bus_find_device_by_of_node(&platform_bus_type, pcie_port);
+ if (!pcie_dev) {
+ dev_err(dev, "Didn't find pcie device\n");
+ return -ENODEV;
+ }
+
+ /*
+ * We might just use NULL instead of the APB name, as the
+ * pcie-kirin currently registers directly just one regmap (although
+ * the DWC driver register other regmaps).
+ *
+ * Yet, it sounds safer to warrant that it will be accessing the
+ * right regmap. So, let's use the named version.
+ */
+ phy->apb = dev_get_regmap(pcie_dev, "kirin_pcie_apb");
+ if (!phy->apb) {
+ dev_err(dev, "Failed to get APB regmap\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+
+static int kirin_pcie_clk_ctrl(struct hi3670_pcie_phy *phy, bool enable)
+{
+ int ret = 0;
+
+ if (!enable)
+ goto close_clk;
+
+ ret = clk_set_rate(phy->phy_ref_clk, REF_CLK_FREQ);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->phy_ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(phy->apb_sys_clk);
+ if (ret)
+ goto apb_sys_fail;
+
+ ret = clk_prepare_enable(phy->apb_phy_clk);
+ if (ret)
+ goto apb_phy_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aclk);
+ if (ret)
+ goto aclk_fail;
+
+ ret = clk_prepare_enable(phy->pcie_aux_clk);
+ if (ret)
+ goto aux_clk_fail;
+
+ return 0;
+
+close_clk:
+ clk_disable_unprepare(phy->pcie_aux_clk);
+aux_clk_fail:
+ clk_disable_unprepare(phy->pcie_aclk);
+aclk_fail:
+ clk_disable_unprepare(phy->apb_phy_clk);
+apb_phy_fail:
+ clk_disable_unprepare(phy->apb_sys_clk);
+apb_sys_fail:
+ clk_disable_unprepare(phy->phy_ref_clk);
+
+ return ret;
+}
+
+static int hi3670_pcie_phy_init(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ struct device *dev = phy->dev;
+ int ret;
+
+ /*
+ * The code under hi3670_pcie_get_apb() need to access the
+ * DWC APB registers. So, get them from
+ * the pcie driver's regmap (see pcie-kirin regmap).
+ *
+ * Such kind of resource can only be obtained during the PCIe
+ * power_on sequence, as the code inside pcie-kirin needs to
+ * be already probed, as it needs to register the APB regmap.
+ */
+
+ ret = hi3670_pcie_get_apb(phy);
+ if (ret)
+ return ret;
+
+ /* phy regulator needs to be powered on before calling it */
+ return hi3670_pcie_gpio_request(phy, dev);
+}
+
+static int hi3670_pcie_phy_power_on(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+ int val, ret, i;
+
+ /* Power supply for Host */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_CMOS_OFFSET, SCTRL_PCIE_CMOS_BIT);
+ usleep_range(TIME_CMOS_MIN, TIME_CMOS_MAX);
+
+ hi3670_pcie_phy_oe_enable(phy);
+
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ ret = gpio_direction_output(phy->gpio_id_clkreq[i], 0);
+ if (ret)
+ return ret;
+ }
+
+ ret = kirin_pcie_clk_ctrl(phy, true);
+ if (ret)
+ return ret;
+
+ /* ISO disable, PCIeCtrl, PHY assert and clk gate clear */
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_ISO_OFFSET, SCTRL_PCIE_ISO_BIT);
+ regmap_write(phy->crgctrl,
+ CRGCTRL_PCIE_ASSERT_OFFSET, CRGCTRL_PCIE_ASSERT_BIT);
+ regmap_write(phy->sysctrl,
+ SCTRL_PCIE_HPCLK_OFFSET, SCTRL_PCIE_HPCLK_BIT);
+
+ hi3670_pcie_natural_cfg(phy);
+
+ ret = hi3670_pcie_allclk_ctrl(phy, true);
+ if (ret)
+ goto disable_clks;
+
+ /* pull down phy_test_powerdown signal */
+ val = hi3670_apb_phy_readl(phy, SOC_PCIEPHY_CTRL0_ADDR);
+ val &= ~(0x1 << 22);
+ hi3670_apb_phy_writel(phy, val, SOC_PCIEPHY_CTRL0_ADDR);
+
+ /* deassert controller perst_n */
+ regmap_read(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, &val);
+ val |= (0x1 << 2);
+ regmap_write(phy->apb, SOC_PCIECTRL_CTRL12_ADDR, val);
+ udelay(10);
+
+ /* perst assert Endpoints */
+ usleep_range(21000, 23000);
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ ret = gpio_direction_output(phy->gpio_id_reset[i], 1);
+ if (ret)
+ return ret;
+ }
+ usleep_range(10000, 11000);
+
+ ret = is_pipe_clk_stable(phy);
+ if (!ret)
+ goto disable_clks;
+
+ hi3670_pcie_set_eyeparam(phy);
+
+ ret = hi3670_pcie_noc_power(phy, false);
+ if (ret)
+ goto disable_clks;
+
+ return 0;
+
+disable_clks:
+ kirin_pcie_clk_ctrl(phy, false);
+ return ret;
+}
+
+static int hi3670_pcie_phy_power_off(struct phy *generic_phy)
+{
+ struct hi3670_pcie_phy *phy = phy_get_drvdata(generic_phy);
+
+ /* Drop power supply for Host */
+ regmap_write(phy->sysctrl, SCTRL_PCIE_CMOS_OFFSET, 0x00);
+
+ kirin_pcie_clk_ctrl(phy, false);
+
+ return 0;
+}
+
+static const struct phy_ops hi3670_phy_ops = {
+ .init = hi3670_pcie_phy_init,
+ .power_on = hi3670_pcie_phy_power_on,
+ .power_off = hi3670_pcie_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int hi3670_pcie_phy_get_resources(struct hi3670_pcie_phy *phy,
+ struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ char name[32];
+ int i;
+
+ /* syscon */
+ phy->crgctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-crgctrl");
+ if (IS_ERR(phy->crgctrl))
+ return PTR_ERR(phy->crgctrl);
+
+ phy->sysctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-sctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ phy->pmctrl = syscon_regmap_lookup_by_compatible("hisilicon,hi3670-pmctrl");
+ if (IS_ERR(phy->sysctrl))
+ return PTR_ERR(phy->sysctrl);
+
+ /* clocks */
+ phy->phy_ref_clk = devm_clk_get(dev, "pcie_phy_ref");
+ if (IS_ERR(phy->phy_ref_clk))
+ return PTR_ERR(phy->phy_ref_clk);
+
+ phy->pcie_aux_clk = devm_clk_get(dev, "pcie_aux");
+ if (IS_ERR(phy->pcie_aux_clk))
+ return PTR_ERR(phy->pcie_aux_clk);
+
+ phy->apb_phy_clk = devm_clk_get(dev, "pcie_apb_phy");
+ if (IS_ERR(phy->apb_phy_clk))
+ return PTR_ERR(phy->apb_phy_clk);
+
+ phy->apb_sys_clk = devm_clk_get(dev, "pcie_apb_sys");
+ if (IS_ERR(phy->apb_sys_clk))
+ return PTR_ERR(phy->apb_sys_clk);
+
+ phy->pcie_aclk = devm_clk_get(dev, "pcie_aclk");
+ if (IS_ERR(phy->pcie_aclk))
+ return PTR_ERR(phy->pcie_aclk);
+
+ /* registers */
+ phy->base = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(phy->base))
+ return PTR_ERR(phy->base);
+
+ /* perst reset gpios */
+ phy->n_gpio_resets = of_gpio_named_count(np, "reset-gpios");
+ if (phy->n_gpio_resets > MAX_GPIO_RESETS) {
+ dev_err(dev, "Too many GPIO resets!\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < phy->n_gpio_resets; i++) {
+ phy->gpio_id_reset[i] = of_get_named_gpio(dev->of_node,
+ "reset-gpios", i);
+ if (phy->gpio_id_reset[i] < 0)
+ return phy->gpio_id_reset[i];
+
+ sprintf(name, "pcie_perst_%d", i);
+
+ phy->reset_names[i] = devm_kstrdup_const(dev, name,
+ GFP_KERNEL);
+ if (!phy->reset_names[i])
+ return -ENOMEM;
+ }
+
+ /* clock request gpios */
+ phy->n_gpio_clkreq = of_gpio_named_count(np, "clkreq-gpios");
+ if (phy->n_gpio_clkreq > MAX_GPIO_CLKREQ) {
+ dev_err(dev, "Too many GPIO clock requests!\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < phy->n_gpio_clkreq; i++) {
+ phy->gpio_id_clkreq[i] = of_get_named_gpio(dev->of_node,
+ "clkreq-gpios", i);
+ if (phy->gpio_id_clkreq[i] < 0)
+ return phy->gpio_id_clkreq[i];
+
+ sprintf(name, "pcie_clkreq_%d", i);
+ phy->clkreq_names[i] = devm_kstrdup_const(dev, name,
+ GFP_KERNEL);
+ if (!phy->clkreq_names[i])
+ return -ENOMEM;
+ }
+
+ hi3670_pcie_get_eyeparam(phy);
+
+ return 0;
+}
+
+static int hi3670_pcie_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct hi3670_pcie_phy *phy;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->dev = dev;
+
+ ret = hi3670_pcie_phy_get_resources(phy, pdev);
+ if (ret)
+ return ret;
+
+ generic_phy = devm_phy_create(dev, dev->of_node, &hi3670_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(generic_phy);
+ }
+
+ phy_set_drvdata(generic_phy, phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi3670_pcie_phy_match[] = {
+ {
+ .compatible = "hisilicon,hi970-pcie-phy",
+ },
+ {},
+};
+
+static struct platform_driver hi3670_pcie_phy_driver = {
+ .probe = hi3670_pcie_phy_probe,
+ .driver = {
+ .of_match_table = hi3670_pcie_phy_match,
+ .name = "hi3670_pcie_phy",
+ .suppress_bind_attrs = true,
+ }
+};
+builtin_platform_driver(hi3670_pcie_phy_driver);
--
2.31.1