2017-06-08 22:35:02

by Stefan Agner

[permalink] [raw]
Subject: [PATCH v6 0/3] ARM: dts: imx7: add NAND support

This revision alters the clock tree such that the clock required by
the APBH DMA (NAND_USDHC_BUS_CLK_ROOT _after_ gate CCGR20) is available
as an independent clock.

So far the gate CCGR20 was used by the NAND_ROOT_CLK only. A previous
patch added the NAND_ROOT_CLK to the APBH DMA which lead the clock
gate CCGR20 getting enabled:
https://patchwork.ozlabs.org/patch/551967/

The data sheet seems to indicate that the APBH DMA only uses hclk which
is connected to NAND_USDHC_BUS_CLK_ROOT, but also through gate CCGR20.
Tests seem to confirm this wiring.

By adding a new clock IMX7D_NAND_USDHC_BUS_RAWNAND_CLK we can assign
a clock which also enables the shared CCGR20 gate without changing the
DMA driver. This better reflects the true wiring and encapsulates the
SoC specific clock wiring in the clock tree instead leaking it into
the driver code.

The wording "rawnand" has been taken from Table 5-12, Module APBHDMA
in the i.MX 7 Reference Manual.

Versions 2 and earlier also included NAND driver changes, which are
already merged.

--
Stefan

Changes since v5:
- Remove clock-names from dma-apbh node

Changes since v4:
- Introduce *_RAWNAND_CLK which represent clocks after CCGR20
- Use *_RAWNAND_CLK for APBH DMA and GPMI NAND
- Use assigned-clocks to set a reasonable parent for NAND_ROOT_SRC

Changes since v3:
- Only specify IMX7D_NAND_USDHC_BUS_ROOT_CLK which seems to be sufficent

Changes since v2:
- Dropped driver changes, alreay merged

Changes since v1:
- Make clks_count const
- Introduce IS_IMX7D for i.MX 7 SoC's and make it part of GPMI_IS_MX6

Stefan Agner (3):
clk: imx7d: create clocks behind rawnand clock gate
ARM: dts: imx7: add GPMI NAND and APBH DMA
ARM: dts: imx7-colibri: add NAND support

arch/arm/boot/dts/imx7-colibri.dtsi | 9 ++++++++-
arch/arm/boot/dts/imx7s.dtsi | 31 ++++++++++++++++++++++++++-
drivers/clk/imx/clk-imx7d.c | 6 +++--
include/dt-bindings/clock/imx7d-clock.h | 4 ++-
4 files changed, 47 insertions(+), 3 deletions(-)

base-commit: e2bb3be2c6c623ff0bad975dc9435531f450f0c5
--
git-series 0.9.1


2017-06-08 22:35:10

by Stefan Agner

[permalink] [raw]
Subject: [PATCH v6 2/3] ARM: dts: imx7: add GPMI NAND and APBH DMA

Add i.MX 7 APBH DMA and GPMI NAND modules.

Signed-off-by: Stefan Agner <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
---
arch/arm/boot/dts/imx7s.dtsi | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)

diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
index c4f12fd..4902f62 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/imx7s.dtsi
@@ -995,5 +995,36 @@
status = "disabled";
};
};
+
+ dma_apbh: dma-apbh@33000000 {
+ compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x33000000 0x2000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
+ };
+
+ gpmi: gpmi-nand@33002000{
+ compatible = "fsl,imx7d-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bch";
+ clocks = <&clks IMX7D_NAND_RAWNAND_CLK>,
+ <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
+ clock-names = "gpmi_io", "gpmi_bch_apb";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ assigned-clocks = <&clks IMX7D_NAND_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_500M_CLK>;
+ };
};
};
--
git-series 0.9.1

2017-06-08 22:35:08

by Stefan Agner

[permalink] [raw]
Subject: [PATCH v6 1/3] clk: imx7d: create clocks behind rawnand clock gate

The rawnand clock gate gates two clocks, NAND_USDHC_BUS_CLK_ROOT
and NAND_CLK_ROOT. However, the gate has been in the chain of the
latter only. This does not allow to use the NAND_USDHC_BUS_CLK_ROOT
only, e.g. as required by APBH-Bridge-DMA.

Add new clocks which represent the clock after the gate, and use a
shared clock gate to correctly model the hardware.

Signed-off-by: Stefan Agner <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
---
drivers/clk/imx/clk-imx7d.c | 6 ++++--
include/dt-bindings/clock/imx7d-clock.h | 4 +++-
2 files changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
index 93b0364..e364060 100644
--- a/drivers/clk/imx/clk-imx7d.c
+++ b/drivers/clk/imx/clk-imx7d.c
@@ -25,6 +25,7 @@
static u32 share_count_sai1;
static u32 share_count_sai2;
static u32 share_count_sai3;
+static u32 share_count_nand;

static struct clk_div_table test_div_table[] = {
{ .val = 3, .div = 1, },
@@ -748,7 +749,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
clks[IMX7D_ENET2_TIME_ROOT_DIV] = imx_clk_divider2("enet2_time_post_div", "enet2_time_pre_div", base + 0xa880, 0, 6);
clks[IMX7D_ENET_PHY_REF_ROOT_DIV] = imx_clk_divider2("enet_phy_ref_post_div", "enet_phy_ref_pre_div", base + 0xa900, 0, 6);
clks[IMX7D_EIM_ROOT_DIV] = imx_clk_divider2("eim_post_div", "eim_pre_div", base + 0xa980, 0, 6);
- clks[IMX7D_NAND_ROOT_DIV] = imx_clk_divider2("nand_post_div", "nand_pre_div", base + 0xaa00, 0, 6);
+ clks[IMX7D_NAND_ROOT_CLK] = imx_clk_divider2("nand_root_clk", "nand_pre_div", base + 0xaa00, 0, 6);
clks[IMX7D_QSPI_ROOT_DIV] = imx_clk_divider2("qspi_post_div", "qspi_pre_div", base + 0xaa80, 0, 6);
clks[IMX7D_USDHC1_ROOT_DIV] = imx_clk_divider2("usdhc1_post_div", "usdhc1_pre_div", base + 0xab00, 0, 6);
clks[IMX7D_USDHC2_ROOT_DIV] = imx_clk_divider2("usdhc2_post_div", "usdhc2_pre_div", base + 0xab80, 0, 6);
@@ -825,7 +826,8 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
clks[IMX7D_ENET2_TIME_ROOT_CLK] = imx_clk_gate4("enet2_time_root_clk", "enet2_time_post_div", base + 0x4510, 0);
clks[IMX7D_ENET_PHY_REF_ROOT_CLK] = imx_clk_gate4("enet_phy_ref_root_clk", "enet_phy_ref_post_div", base + 0x4520, 0);
clks[IMX7D_EIM_ROOT_CLK] = imx_clk_gate4("eim_root_clk", "eim_post_div", base + 0x4160, 0);
- clks[IMX7D_NAND_ROOT_CLK] = imx_clk_gate4("nand_root_clk", "nand_post_div", base + 0x4140, 0);
+ clks[IMX7D_NAND_RAWNAND_CLK] = imx_clk_gate2_shared2("nand_rawnand_clk", "nand_root_clk", base + 0x4140, 0, &share_count_nand);
+ clks[IMX7D_NAND_USDHC_BUS_RAWNAND_CLK] = imx_clk_gate2_shared2("nand_usdhc_rawnand_clk", "nand_usdhc_root_clk", base + 0x4140, 0, &share_count_nand);
clks[IMX7D_QSPI_ROOT_CLK] = imx_clk_gate4("qspi_root_clk", "qspi_post_div", base + 0x4150, 0);
clks[IMX7D_USDHC1_ROOT_CLK] = imx_clk_gate4("usdhc1_root_clk", "usdhc1_post_div", base + 0x46c0, 0);
clks[IMX7D_USDHC2_ROOT_CLK] = imx_clk_gate4("usdhc2_root_clk", "usdhc2_post_div", base + 0x46d0, 0);
diff --git a/include/dt-bindings/clock/imx7d-clock.h b/include/dt-bindings/clock/imx7d-clock.h
index a7a1a50..de62a83 100644
--- a/include/dt-bindings/clock/imx7d-clock.h
+++ b/include/dt-bindings/clock/imx7d-clock.h
@@ -450,5 +450,7 @@
#define IMX7D_CLK_ARM 437
#define IMX7D_CKIL 438
#define IMX7D_OCOTP_CLK 439
-#define IMX7D_CLK_END 440
+#define IMX7D_NAND_RAWNAND_CLK 440
+#define IMX7D_NAND_USDHC_BUS_RAWNAND_CLK 441
+#define IMX7D_CLK_END 442
#endif /* __DT_BINDINGS_CLOCK_IMX7D_H */
--
git-series 0.9.1

2017-06-08 22:35:30

by Stefan Agner

[permalink] [raw]
Subject: [PATCH v6 3/3] ARM: dts: imx7-colibri: add NAND support

The Colibri iMX7 modules come with 512MB on-module SLC NAND flash
populated. Make use of it by enabling the GPMI controller.

Signed-off-by: Stefan Agner <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
---
arch/arm/boot/dts/imx7-colibri.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 2d87489..ad4ce19 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -106,6 +106,15 @@
fsl,magic-packet;
};

+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ fsl,use-minimum-ecc;
+ nand-on-flash-bbt;
+ nand-ecc-mode = "hw";
+ status = "okay";
+};
+
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
--
git-series 0.9.1

2017-06-09 19:16:39

by Han Xu

[permalink] [raw]
Subject: Re: [PATCH v6 1/3] clk: imx7d: create clocks behind rawnand clock gate



On 06/08/2017 05:34 PM, Stefan Agner wrote:
> The rawnand clock gate gates two clocks, NAND_USDHC_BUS_CLK_ROOT
> and NAND_CLK_ROOT. However, the gate has been in the chain of the
> latter only. This does not allow to use the NAND_USDHC_BUS_CLK_ROOT
> only, e.g. as required by APBH-Bridge-DMA.
>
> Add new clocks which represent the clock after the gate, and use a
> shared clock gate to correctly model the hardware.
>
> Signed-off-by: Stefan Agner <[email protected]>
> Tested-by: Fabio Estevam <[email protected]>
Acked-by: Han Xu <[email protected]>
> ---
> drivers/clk/imx/clk-imx7d.c | 6 ++++--
> include/dt-bindings/clock/imx7d-clock.h | 4 +++-
> 2 files changed, 7 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
> index 93b0364..e364060 100644
> --- a/drivers/clk/imx/clk-imx7d.c
> +++ b/drivers/clk/imx/clk-imx7d.c
> @@ -25,6 +25,7 @@
> static u32 share_count_sai1;
> static u32 share_count_sai2;
> static u32 share_count_sai3;
> +static u32 share_count_nand;
>
> static struct clk_div_table test_div_table[] = {
> { .val = 3, .div = 1, },
> @@ -748,7 +749,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
> clks[IMX7D_ENET2_TIME_ROOT_DIV] = imx_clk_divider2("enet2_time_post_div", "enet2_time_pre_div", base + 0xa880, 0, 6);
> clks[IMX7D_ENET_PHY_REF_ROOT_DIV] = imx_clk_divider2("enet_phy_ref_post_div", "enet_phy_ref_pre_div", base + 0xa900, 0, 6);
> clks[IMX7D_EIM_ROOT_DIV] = imx_clk_divider2("eim_post_div", "eim_pre_div", base + 0xa980, 0, 6);
> - clks[IMX7D_NAND_ROOT_DIV] = imx_clk_divider2("nand_post_div", "nand_pre_div", base + 0xaa00, 0, 6);
> + clks[IMX7D_NAND_ROOT_CLK] = imx_clk_divider2("nand_root_clk", "nand_pre_div", base + 0xaa00, 0, 6);
> clks[IMX7D_QSPI_ROOT_DIV] = imx_clk_divider2("qspi_post_div", "qspi_pre_div", base + 0xaa80, 0, 6);
> clks[IMX7D_USDHC1_ROOT_DIV] = imx_clk_divider2("usdhc1_post_div", "usdhc1_pre_div", base + 0xab00, 0, 6);
> clks[IMX7D_USDHC2_ROOT_DIV] = imx_clk_divider2("usdhc2_post_div", "usdhc2_pre_div", base + 0xab80, 0, 6);
> @@ -825,7 +826,8 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
> clks[IMX7D_ENET2_TIME_ROOT_CLK] = imx_clk_gate4("enet2_time_root_clk", "enet2_time_post_div", base + 0x4510, 0);
> clks[IMX7D_ENET_PHY_REF_ROOT_CLK] = imx_clk_gate4("enet_phy_ref_root_clk", "enet_phy_ref_post_div", base + 0x4520, 0);
> clks[IMX7D_EIM_ROOT_CLK] = imx_clk_gate4("eim_root_clk", "eim_post_div", base + 0x4160, 0);
> - clks[IMX7D_NAND_ROOT_CLK] = imx_clk_gate4("nand_root_clk", "nand_post_div", base + 0x4140, 0);
> + clks[IMX7D_NAND_RAWNAND_CLK] = imx_clk_gate2_shared2("nand_rawnand_clk", "nand_root_clk", base + 0x4140, 0, &share_count_nand);
> + clks[IMX7D_NAND_USDHC_BUS_RAWNAND_CLK] = imx_clk_gate2_shared2("nand_usdhc_rawnand_clk", "nand_usdhc_root_clk", base + 0x4140, 0, &share_count_nand);
> clks[IMX7D_QSPI_ROOT_CLK] = imx_clk_gate4("qspi_root_clk", "qspi_post_div", base + 0x4150, 0);
> clks[IMX7D_USDHC1_ROOT_CLK] = imx_clk_gate4("usdhc1_root_clk", "usdhc1_post_div", base + 0x46c0, 0);
> clks[IMX7D_USDHC2_ROOT_CLK] = imx_clk_gate4("usdhc2_root_clk", "usdhc2_post_div", base + 0x46d0, 0);
> diff --git a/include/dt-bindings/clock/imx7d-clock.h b/include/dt-bindings/clock/imx7d-clock.h
> index a7a1a50..de62a83 100644
> --- a/include/dt-bindings/clock/imx7d-clock.h
> +++ b/include/dt-bindings/clock/imx7d-clock.h
> @@ -450,5 +450,7 @@
> #define IMX7D_CLK_ARM 437
> #define IMX7D_CKIL 438
> #define IMX7D_OCOTP_CLK 439
> -#define IMX7D_CLK_END 440
> +#define IMX7D_NAND_RAWNAND_CLK 440
> +#define IMX7D_NAND_USDHC_BUS_RAWNAND_CLK 441
> +#define IMX7D_CLK_END 442
> #endif /* __DT_BINDINGS_CLOCK_IMX7D_H */

2017-06-09 19:17:09

by Han Xu

[permalink] [raw]
Subject: Re: [PATCH v6 2/3] ARM: dts: imx7: add GPMI NAND and APBH DMA



On 06/08/2017 05:34 PM, Stefan Agner wrote:
> Add i.MX 7 APBH DMA and GPMI NAND modules.
>
> Signed-off-by: Stefan Agner <[email protected]>
> Tested-by: Fabio Estevam <[email protected]>
Acked-by: Han Xu <[email protected]>
> ---
> arch/arm/boot/dts/imx7s.dtsi | 31 +++++++++++++++++++++++++++++++
> 1 file changed, 31 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
> index c4f12fd..4902f62 100644
> --- a/arch/arm/boot/dts/imx7s.dtsi
> +++ b/arch/arm/boot/dts/imx7s.dtsi
> @@ -995,5 +995,36 @@
> status = "disabled";
> };
> };
> +
> + dma_apbh: dma-apbh@33000000 {
> + compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
> + reg = <0x33000000 0x2000>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
> + #dma-cells = <1>;
> + dma-channels = <4>;
> + clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
> + };
> +
> + gpmi: gpmi-nand@33002000{
> + compatible = "fsl,imx7d-gpmi-nand";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
> + reg-names = "gpmi-nand", "bch";
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "bch";
> + clocks = <&clks IMX7D_NAND_RAWNAND_CLK>,
> + <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
> + clock-names = "gpmi_io", "gpmi_bch_apb";
> + dmas = <&dma_apbh 0>;
> + dma-names = "rx-tx";
> + status = "disabled";
> + assigned-clocks = <&clks IMX7D_NAND_ROOT_SRC>;
> + assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_500M_CLK>;
> + };
> };
> };

2017-06-09 19:17:31

by Han Xu

[permalink] [raw]
Subject: Re: [PATCH v6 3/3] ARM: dts: imx7-colibri: add NAND support



On 06/08/2017 05:34 PM, Stefan Agner wrote:
> The Colibri iMX7 modules come with 512MB on-module SLC NAND flash
> populated. Make use of it by enabling the GPMI controller.
>
> Signed-off-by: Stefan Agner <[email protected]>
> Tested-by: Fabio Estevam <[email protected]>
Acked-by: Han Xu <[email protected]>
> ---
> arch/arm/boot/dts/imx7-colibri.dtsi | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
> index 2d87489..ad4ce19 100644
> --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> @@ -106,6 +106,15 @@
> fsl,magic-packet;
> };
>
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + fsl,use-minimum-ecc;
> + nand-on-flash-bbt;
> + nand-ecc-mode = "hw";
> + status = "okay";
> +};
> +
> &i2c1 {
> clock-frequency = <100000>;
> pinctrl-names = "default";

2017-06-14 15:12:41

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v6 0/3] ARM: dts: imx7: add NAND support

On Thu, Jun 08, 2017 at 03:34:46PM -0700, Stefan Agner wrote:
> Stefan Agner (3):
> clk: imx7d: create clocks behind rawnand clock gate
> ARM: dts: imx7: add GPMI NAND and APBH DMA
> ARM: dts: imx7-colibri: add NAND support

Both dts patches look good to me. Please ping me after the clk patch
lands on mainline.

Shawn

2017-06-20 01:01:42

by Stephen Boyd

[permalink] [raw]
Subject: Re: [PATCH v6 1/3] clk: imx7d: create clocks behind rawnand clock gate

On 06/08, Stefan Agner wrote:
> The rawnand clock gate gates two clocks, NAND_USDHC_BUS_CLK_ROOT
> and NAND_CLK_ROOT. However, the gate has been in the chain of the
> latter only. This does not allow to use the NAND_USDHC_BUS_CLK_ROOT
> only, e.g. as required by APBH-Bridge-DMA.
>
> Add new clocks which represent the clock after the gate, and use a
> shared clock gate to correctly model the hardware.
>
> Signed-off-by: Stefan Agner <[email protected]>
> Tested-by: Fabio Estevam <[email protected]>
> ---

Applied to clk-next

--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

2017-08-02 02:43:58

by Stefan Agner

[permalink] [raw]
Subject: Re: [PATCH v6 0/3] ARM: dts: imx7: add NAND support

Hi Shawn,

On 2017-06-14 08:11, Shawn Guo wrote:
> On Thu, Jun 08, 2017 at 03:34:46PM -0700, Stefan Agner wrote:
>> Stefan Agner (3):
>> clk: imx7d: create clocks behind rawnand clock gate
>> ARM: dts: imx7: add GPMI NAND and APBH DMA
>> ARM: dts: imx7-colibri: add NAND support
>
> Both dts patches look good to me. Please ping me after the clk patch
> lands on mainline.

The clk patch landed in mainline. These two patches seem to apply fine
still. Can you queue them for -next?

FWIW, tested it on a Colibri iMX7 using v3.13-rc3, works fine after
reverting the GPC changes (see my other email with subject "i.MX 7 boot
freeze with 4.13-rc3").

--
Stefan

2017-08-03 01:15:07

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v6 0/3] ARM: dts: imx7: add NAND support

On Tue, Aug 01, 2017 at 07:41:41PM -0700, Stefan Agner wrote:
> Hi Shawn,
>
> On 2017-06-14 08:11, Shawn Guo wrote:
> > On Thu, Jun 08, 2017 at 03:34:46PM -0700, Stefan Agner wrote:
> >> Stefan Agner (3):
> >> clk: imx7d: create clocks behind rawnand clock gate
> >> ARM: dts: imx7: add GPMI NAND and APBH DMA
> >> ARM: dts: imx7-colibri: add NAND support
> >
> > Both dts patches look good to me. Please ping me after the clk patch
> > lands on mainline.
>
> The clk patch landed in mainline. These two patches seem to apply fine
> still. Can you queue them for -next?

Just applied. Thanks for reminding.

Shawn