2023-07-15 09:23:08

by David Wronek

Subject: [PATCH v3 5/7] arm64: dts: qcom: pm6150: Add resin and rtc nodes

Add support for the RTC which is the same as on other PMICs and add the
resin child node to the PM6150 PON device, both disabled by default.

Signed-off-by: David Wronek <[email protected]>
Tested-by: Nikita Travkin <[email protected]>
---
arch/arm64/boot/dts/qcom/pm6150.dtsi | 16 ++++++++++++++++
1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
index 2e6afa296141..af51eb0646ba 100644
--- a/arch/arm64/boot/dts/qcom/pm6150.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
@@ -53,6 +53,14 @@ pm6150_pwrkey: pwrkey {
bias-pull-up;
linux,code = <KEY_POWER>;
};
+
+ pm6150_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ status = "disabled";
+ };
};

pm6150_temp: temp-alarm@2400 {
@@ -88,6 +96,14 @@ pm6150_adc_tm: adc-tm@3500 {
status = "disabled";
};

+ pm6150_rtc: rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>, <0x6100>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
pm6150_gpios: gpio@c000 {
compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
--
2.41.0

2023-07-15 14:53:25

by Konrad Dybcio

Subject: Re: [PATCH v3 5/7] arm64: dts: qcom: pm6150: Add resin and rtc nodes

On 15.07.2023 11:16, David Wronek wrote:
> Add support for the RTC which is the same as on other PMICs and add the
> resin child node to the PM6150 PON device, both disabled by default.
>
> Signed-off-by: David Wronek <[email protected]>
> Tested-by: Nikita Travkin <[email protected]>
> ---
Reviewed-by: Konrad Dybcio <[email protected]>

Konrad
> arch/arm64/boot/dts/qcom/pm6150.dtsi | 16 ++++++++++++++++
> 1 file changed, 16 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> index 2e6afa296141..af51eb0646ba 100644
> --- a/arch/arm64/boot/dts/qcom/pm6150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> @@ -53,6 +53,14 @@ pm6150_pwrkey: pwrkey {
> bias-pull-up;
> linux,code = <KEY_POWER>;
> };
> +
> + pm6150_resin: resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + status = "disabled";
> + };
> };
>
> pm6150_temp: temp-alarm@2400 {
> @@ -88,6 +96,14 @@ pm6150_adc_tm: adc-tm@3500 {
> status = "disabled";
> };
>
> + pm6150_rtc: rtc@6000 {
> + compatible = "qcom,pm8941-rtc";
> + reg = <0x6000>, <0x6100>;
> + reg-names = "rtc", "alarm";
> + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
> + status = "disabled";
> + };
> +
> pm6150_gpios: gpio@c000 {
> compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
> reg = <0xc000>;