*** Announcement: dmraid 1.0.0.rc10 ***
dmraid 1.0.0.rc10 is available at
http://people.redhat.com/heinzm/sw/dmraid/ in source tarball,
source rpm and i386 rpm (with shared and static binary).
This release adds support for Adaptec HostRAID and JMicron JMB36X
(see CHANGELOG below for more information).
dmraid (Device-Mapper RAID tool) discovers, [de]activates and displays
properties of software RAID sets (i.e. ATARAID) and contained DOS
partitions using the device-mapper runtime of the 2.6 kernel.
The following ATARAID types are supported on Linux 2.6:
Adaptec HostRAID ASR
Highpoint HPT37X
Highpoint HPT45X
Intel Software RAID
JMicron JMB36X
LSI Logic MegaRAID
NVidia NForce
Promise FastTrack
Silicon Image Medley
VIA Software RAID
Please provide insight to support those metadata formats completely.
Thanks.
See files README, which comes with the source tarball for
prerequisites to run this software, further instructions on installing
and using dmraid!
Call for testers:
-----------------
I need testers with the above ATARAID types, to check that the mapping
created by this tool is correct (see options "-t -ay") and access to the
ATARAID data is proper.
In case you have a different ATARAID solution from those listed above,
please feel free to contact me about supporting it in dmraid.
You can activate your ATARAID sets without danger of overwriting
your metadata, because dmraid accesses it read-only unless you use
option -E together with -r in order to erase ATARAID metadata
(see 'man dmraid')!
This is a release candidate version so you want to have backups of your valuable
data *and* you want to test accessing your data read-only first in order to
make sure that the mapping is correct before you go for read-write access.
Contacts:
---------
The author is reachable at <[email protected]>.
For test results, mapping information, discussions, questions, patches,
enhancement requests and the like, please subscribe and mail to
<[email protected]>.
--
Regards,
Heinz -- The LVM Guy --
Changelog from dmraid 1.0.0.rc9 to 1.0.0.rc10 2006.02.17
FIXES:
------
o metadata.c: want_set() didn't drop sets properly
(eg, jmicron_raid10 wanted and jmicron_raid1 not dropped)
o scsi.c: avoid retrieving too much data (Al Viro)
o sil.h: magic number fix (some arrays were not recognized)
FEATURES:
---------
o added libdmraid_make_table() to activate.c to be used by installer
o asr.[ch]: added Adaptec HostRAID support
o jm.[ch]: added JMicron JMB36x support
o added '--enable-libselinux' to configure for those who want
to build without it
o bytorder.h: enhanced to support big endian conversion
on little endian arch
o nv.c: support RAID5 with dm-raid45 target
o pdc.h: support additional metadata offset
o metadata.c: enhanced to support RAID4 and RAID5 mappings with dm-raid45 target
MISCELANIOUS:
-------------
o misc.c: streamlined remove_white_space() (Al Viro)
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Heinz Mauelshagen Red Hat GmbH
Consulting Development Engineer Am Sonnenhang 11
56242 Marienrachdorf
Germany
[email protected] +49 2626 141200
FAX 924446
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
On Tue, Feb 21, 2006 at 05:10:26PM +0100, Thierry Vignaud wrote:
> Heinz Mauelshagen <[email protected]> writes:
>
> > *** Announcement: dmraid 1.0.0.rc10 ***
> >
> > dmraid 1.0.0.rc10 is available at
> > http://people.redhat.com/heinzm/sw/dmraid/ in source tarball,
> > source rpm and i386 rpm (with shared and static binary).
> >
> > This release adds support for Adaptec HostRAID and JMicron JMB36X
> > (see CHANGELOG below for more information).
>
> you're missusing AC_ARG_ENABLE: it cannot assume whereas you want to
> default to --enable-XXX or --disable-XXX.
>
> eg passing --disable-selinux to dmraid's configures make it actually
> enable selinux support :-(
Well, I better tested --disable-libselinux rather than just leaving
the respective option out or configure --enable-libselinux, which most people
will do anyway ;-)
>
> the format is "AC_ARG_ENABLE(name, help, [ use given value ], [ default action ])"
>
> the following patch fixes it:
Applied.
>
> you might want to alter default values then since i guess you
> misunderstood what the arguments should have been.
Hrm, configure option got added last minute.
Thanks,
Heinz
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Heinz Mauelshagen Red Hat GmbH
Consulting Development Engineer Am Sonnenhang 11
Cluster and Storage Development 56242 Marienrachdorf
Germany
[email protected] +49 2626 141200
FAX 924446
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-