On Thu, Aug 24, 2023 at 06:00:01PM +0530, Priyansh Jain wrote:
> Add tsens and thermal devicetree node for sa8775p SoC.
>
> Signed-off-by: Priyansh Jain <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 1096 +++++++++++++++++++++++++
> 1 file changed, 1096 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> index b130136acffe..abba42ea5946 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> @@ -2306,6 +2306,1102 @@
>
> #freq-domain-cells = <1>;
I believe this would be the tail of the cpufreq_hw node, @0x18591000.
> };
> +
> + tsens0: thermal-sensor@c222000 {
> + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2";
> + reg = <0x0 0x0c263000 0x0 0x1ff>,
If so, then this is not inserted to maintain the sort order (by address)
of the nodes under /soc. Please update the placement of this node.
Also, the unit address above is c222000, but based on this cell it
should be c263000.
> + <0x0 0x0c222000 0x0 0x8>;
> + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
> + #qcom,sensors = <12>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + tsens1: thermal-sensor@c223000 {
> + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2";
> + reg = <0x0 0x0c265000 0x0 0x1ff>,
> + <0x0 0x0c223000 0x0 0x8>;
> + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
> + #qcom,sensors = <12>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + tsens2: thermal-sensor@c224000 {
> + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2";
> + reg = <0x0 0x0c251000 0x0 0x1ff>,
0x0c251000 < 0x0c265000, please order them properly.
> + <0x0 0x0c224000 0x0 0x8>;
> + interrupts = <GIC_SPI 572 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 609 IRQ_TYPE_LEVEL_HIGH>;
> + #qcom,sensors = <13>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + tsens3: thermal-sensor@c225000 {
> + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2";
> + reg = <0x0 0x0c252000 0x0 0x1ff>,
> + <0x0 0x0c225000 0x0 0x8>;
> + interrupts = <GIC_SPI 573 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 610 IRQ_TYPE_LEVEL_HIGH>;
> + #qcom,sensors = <13>;
> + interrupt-names = "uplow", "critical";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + thermal_zones: thermal-zones {
This does not belong alongside the mmio-devices under /soc, move this
out (and keep / sorted alphabetically on the node name).
> + aoss-0-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&tsens0 0>;
> +
> + trips {
> + aoss0_alert0: trip-point0 {
Why does all these nodes have labels?
> + temperature = <105000>;
> + hysteresis = <5000>;
> + type = "passive";
> + };
> +
> + aoss0_alert1: trip-point1 {
> + temperature = <115000>;
> + hysteresis = <5000>;
> + type = "passive";
> + };
> + };
> + };
> +
[..]
> + };
/soc does not end here anymore, please remember to rebase the change on
v6.6-rc1.
Thanks,
Bjorn
> };
>
> arch_timer: timer {
> --
> 2.17.1
>