P4, running 2.6.3 with APM using sis-agp.
IRQ10 is used by AGP, why is it not listed in /proc/interrupts?
Regards
Michael
CPU0
0: 248480 XT-PIC timer
1: 13 XT-PIC i8042
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
11: 1348 XT-PIC eth0
12: 58 XT-PIC i8042
14: 2246 XT-PIC ide0
NMI: 0
ERR: 0
C ide0
NMI: 0
ERR: 0
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS650/651/M650/740 PCI/AGP VGA Display Adapter (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 5339
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
BIST result: 00
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at eb000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d000 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00: 39 10 25 63 03 00 b0 02 00 00 00 03 00 00 00 80
10: 08 00 00 e0 00 00 00 eb 01 d0 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 39 53
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00
40: 01 50 02 06 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 00 20 00 07 02 00 0f 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00