Move DCS off commands from .unprepare to .disable so that they
actually reach the DSI host.
Signed-off-by: Barnabás Czémán <[email protected]>
---
drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
index 483dc88d16d8..f7222974d6ed 100644
--- a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
+++ b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
@@ -169,6 +169,15 @@ static int jdi_fhd_r63452_prepare(struct drm_panel *panel)
}
static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
+{
+ struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
+
+ gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
+ return 0;
+}
+
+static int jdi_fhd_r63452_disable(struct drm_panel *panel)
{
struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
struct device *dev = &ctx->dsi->dev;
@@ -178,8 +187,6 @@ static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
if (ret < 0)
dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
- gpiod_set_value_cansleep(ctx->reset_gpio, 1);
-
return 0;
}
@@ -219,6 +226,7 @@ static int jdi_fhd_r63452_get_modes(struct drm_panel *panel,
static const struct drm_panel_funcs jdi_fhd_r63452_panel_funcs = {
.prepare = jdi_fhd_r63452_prepare,
.unprepare = jdi_fhd_r63452_unprepare,
+ .disable = jdi_fhd_r63452_disable,
.get_modes = jdi_fhd_r63452_get_modes,
};
---
base-commit: 704ba27ac55579704ba1289392448b0c66b56258
change-id: 20240509-jdi-use-disable-ee29098d9c81
Best regards,
--
Barnabás Czémán <[email protected]>
On Thu, May 09, 2024 at 08:14:07PM +0200, Barnab?s Cz?m?n wrote:
> Move DCS off commands from .unprepare to .disable so that they
> actually reach the DSI host.
>
> Signed-off-by: Barnab?s Cz?m?n <[email protected]>
> ---
> drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c | 12 ++++++++++--
> 1 file changed, 10 insertions(+), 2 deletions(-)
I don't think this is correct. If the driver sends enable commands in
prepare, it should be able to send commands during unprepare too.
>
> diff --git a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> index 483dc88d16d8..f7222974d6ed 100644
> --- a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> +++ b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> @@ -169,6 +169,15 @@ static int jdi_fhd_r63452_prepare(struct drm_panel *panel)
> }
>
> static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
> +{
> + struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
> +
> + gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> +
> + return 0;
> +}
> +
> +static int jdi_fhd_r63452_disable(struct drm_panel *panel)
> {
> struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
> struct device *dev = &ctx->dsi->dev;
> @@ -178,8 +187,6 @@ static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
> if (ret < 0)
> dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
>
> - gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> -
> return 0;
> }
>
> @@ -219,6 +226,7 @@ static int jdi_fhd_r63452_get_modes(struct drm_panel *panel,
> static const struct drm_panel_funcs jdi_fhd_r63452_panel_funcs = {
> .prepare = jdi_fhd_r63452_prepare,
> .unprepare = jdi_fhd_r63452_unprepare,
> + .disable = jdi_fhd_r63452_disable,
> .get_modes = jdi_fhd_r63452_get_modes,
> };
>
>
> ---
> base-commit: 704ba27ac55579704ba1289392448b0c66b56258
> change-id: 20240509-jdi-use-disable-ee29098d9c81
>
> Best regards,
> --
> Barnab?s Cz?m?n <[email protected]>
>
--
With best wishes
Dmitry
On Fri, May 10, 2024 at 2:56 AM Dmitry Baryshkov
<[email protected]> wrote:
>
> On Thu, May 09, 2024 at 08:14:07PM +0200, Barnabás Czémán wrote:
> > Move DCS off commands from .unprepare to .disable so that they
> > actually reach the DSI host.
> >
> > Signed-off-by: Barnabás Czémán <[email protected]>
> > ---
> > drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c | 12 ++++++++++--
> > 1 file changed, 10 insertions(+), 2 deletions(-)
>
> I don't think this is correct. If the driver sends enable commands in
> prepare, it should be able to send commands during unprepare too.
>
It cannot send commands in unprepare, there are multiple panel drivers
what do the same.
Every panel drivers which have DCS commands to be sent in unprepare
has similar error messages with mdp5/dpu.
[ 92.322564] panel-td4320-boeplus c994000.dsi.0: sending command
0x28 failed: -22
[ 92.322635] panel-td4320-boeplus c994000.dsi.0: Failed to
un-initialize panel: -22
> >
> > diff --git a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> > index 483dc88d16d8..f7222974d6ed 100644
> > --- a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> > +++ b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> > @@ -169,6 +169,15 @@ static int jdi_fhd_r63452_prepare(struct drm_panel *panel)
> > }
> >
> > static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
> > +{
> > + struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
> > +
> > + gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> > +
> > + return 0;
> > +}
> > +
> > +static int jdi_fhd_r63452_disable(struct drm_panel *panel)
> > {
> > struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
> > struct device *dev = &ctx->dsi->dev;
> > @@ -178,8 +187,6 @@ static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
> > if (ret < 0)
> > dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
> >
> > - gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> > -
> > return 0;
> > }
> >
> > @@ -219,6 +226,7 @@ static int jdi_fhd_r63452_get_modes(struct drm_panel *panel,
> > static const struct drm_panel_funcs jdi_fhd_r63452_panel_funcs = {
> > .prepare = jdi_fhd_r63452_prepare,
> > .unprepare = jdi_fhd_r63452_unprepare,
> > + .disable = jdi_fhd_r63452_disable,
> > .get_modes = jdi_fhd_r63452_get_modes,
> > };
> >
> >
> > ---
> > base-commit: 704ba27ac55579704ba1289392448b0c66b56258
> > change-id: 20240509-jdi-use-disable-ee29098d9c81
> >
> > Best regards,
> > --
> > Barnabás Czémán <[email protected]>
> >
>
> --
> With best wishes
> Dmitry
On Fri, May 10, 2024 at 8:46 AM Barnabás Czémán <[email protected]> wrote:
>
> On Fri, May 10, 2024 at 2:56 AM Dmitry Baryshkov
> <[email protected]> wrote:
> >
> > On Thu, May 09, 2024 at 08:14:07PM +0200, Barnabás Czémán wrote:
> > > Move DCS off commands from .unprepare to .disable so that they
> > > actually reach the DSI host.
> > >
> > > Signed-off-by: Barnabás Czémán <[email protected]>
> > > ---
> > > drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c | 12 ++++++++++--
> > > 1 file changed, 10 insertions(+), 2 deletions(-)
> >
> > I don't think this is correct. If the driver sends enable commands in
> > prepare, it should be able to send commands during unprepare too.
> >
> It cannot send commands in unprepare, there are multiple panel drivers
> what do the same.
> Every panel drivers which have DCS commands to be sent in unprepare
> has similar error messages with mdp5/dpu.
>
> [ 92.322564] panel-td4320-boeplus c994000.dsi.0: sending command
> 0x28 failed: -22
> [ 92.322635] panel-td4320-boeplus c994000.dsi.0: Failed to
> un-initialize panel: -22
>
>
Here is the error messages, these are comes from unprepare by every panel off:
[ 121.295290] panel-jdi-fhd-r63452 994000.dsi.0: transmit data failed: -22
[ 121.295368] panel-jdi-fhd-r63452 994000.dsi.0: Failed to
un-initialize panel: -22
[ 184.783019] panel-jdi-fhd-r63452 994000.dsi.0: transmit data failed: -22
[ 184.783066] panel-jdi-fhd-r63452 994000.dsi.0: Failed to
un-initialize panel: -22
with this patch these errors no more.
prepare works because of this flag ctx->panel.prepare_prev_first = true;
> > >
> > > diff --git a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> > > index 483dc88d16d8..f7222974d6ed 100644
> > > --- a/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> > > +++ b/drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c
> > > @@ -169,6 +169,15 @@ static int jdi_fhd_r63452_prepare(struct drm_panel *panel)
> > > }
> > >
> > > static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
> > > +{
> > > + struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
> > > +
> > > + gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int jdi_fhd_r63452_disable(struct drm_panel *panel)
> > > {
> > > struct jdi_fhd_r63452 *ctx = to_jdi_fhd_r63452(panel);
> > > struct device *dev = &ctx->dsi->dev;
> > > @@ -178,8 +187,6 @@ static int jdi_fhd_r63452_unprepare(struct drm_panel *panel)
> > > if (ret < 0)
> > > dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
> > >
> > > - gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> > > -
> > > return 0;
> > > }
> > >
> > > @@ -219,6 +226,7 @@ static int jdi_fhd_r63452_get_modes(struct drm_panel *panel,
> > > static const struct drm_panel_funcs jdi_fhd_r63452_panel_funcs = {
> > > .prepare = jdi_fhd_r63452_prepare,
> > > .unprepare = jdi_fhd_r63452_unprepare,
> > > + .disable = jdi_fhd_r63452_disable,
> > > .get_modes = jdi_fhd_r63452_get_modes,
> > > };
> > >
> > >
> > > ---
> > > base-commit: 704ba27ac55579704ba1289392448b0c66b56258
> > > change-id: 20240509-jdi-use-disable-ee29098d9c81
> > >
> > > Best regards,
> > > --
> > > Barnabás Czémán <[email protected]>
> > >
> >
> > --
> > With best wishes
> > Dmitry
On Fri, May 10, 2024 at 09:10:34AM +0200, Barnabás Czémán wrote:
> On Fri, May 10, 2024 at 8:46 AM Barnabás Czémán <[email protected]> wrote:
> >
> > On Fri, May 10, 2024 at 2:56 AM Dmitry Baryshkov
> > <[email protected]> wrote:
> > >
> > > On Thu, May 09, 2024 at 08:14:07PM +0200, Barnabás Czémán wrote:
> > > > Move DCS off commands from .unprepare to .disable so that they
> > > > actually reach the DSI host.
> > > >
> > > > Signed-off-by: Barnabás Czémán <[email protected]>
> > > > ---
> > > > drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c | 12 ++++++++++--
> > > > 1 file changed, 10 insertions(+), 2 deletions(-)
> > >
> > > I don't think this is correct. If the driver sends enable commands in
> > > prepare, it should be able to send commands during unprepare too.
> > >
> > It cannot send commands in unprepare, there are multiple panel drivers
> > what do the same.
> > Every panel drivers which have DCS commands to be sent in unprepare
> > has similar error messages with mdp5/dpu.
> >
> > [ 92.322564] panel-td4320-boeplus c994000.dsi.0: sending command
> > 0x28 failed: -22
> > [ 92.322635] panel-td4320-boeplus c994000.dsi.0: Failed to
> > un-initialize panel: -22
> >
> >
> Here is the error messages, these are comes from unprepare by every panel off:
> [ 121.295290] panel-jdi-fhd-r63452 994000.dsi.0: transmit data failed: -22
> [ 121.295368] panel-jdi-fhd-r63452 994000.dsi.0: Failed to
> un-initialize panel: -22
> [ 184.783019] panel-jdi-fhd-r63452 994000.dsi.0: transmit data failed: -22
> [ 184.783066] panel-jdi-fhd-r63452 994000.dsi.0: Failed to
> un-initialize panel: -22
> with this patch these errors no more.
> .prepare works because of this flag ctx->panel.prepare_prev_first = true;
The flag should also invert the order of post_disable chain. It well
might be that the drm/msm/dsi driver shuts down the DSI link too soon.
Please consider fixing the MSM DSI driver instead.
--
With best wishes
Dmitry
On Fri, May 10, 2024 at 8:02 PM Dmitry Baryshkov
<[email protected]> wrote:
>
> On Fri, May 10, 2024 at 09:10:34AM +0200, Barnabás Czémán wrote:
> > On Fri, May 10, 2024 at 8:46 AM Barnabás Czémán <[email protected]> wrote:
> > >
> > > On Fri, May 10, 2024 at 2:56 AM Dmitry Baryshkov
> > > <[email protected]> wrote:
> > > >
> > > > On Thu, May 09, 2024 at 08:14:07PM +0200, Barnabás Czémán wrote:
> > > > > Move DCS off commands from .unprepare to .disable so that they
> > > > > actually reach the DSI host.
> > > > >
> > > > > Signed-off-by: Barnabás Czémán <[email protected]>
> > > > > ---
> > > > > drivers/gpu/drm/panel/panel-jdi-fhd-r63452.c | 12 ++++++++++--
> > > > > 1 file changed, 10 insertions(+), 2 deletions(-)
> > > >
> > > > I don't think this is correct. If the driver sends enable commands in
> > > > prepare, it should be able to send commands during unprepare too.
> > > >
> > > It cannot send commands in unprepare, there are multiple panel drivers
> > > what do the same.
> > > Every panel drivers which have DCS commands to be sent in unprepare
> > > has similar error messages with mdp5/dpu.
> > >
> > > [ 92.322564] panel-td4320-boeplus c994000.dsi.0: sending command
> > > 0x28 failed: -22
> > > [ 92.322635] panel-td4320-boeplus c994000.dsi.0: Failed to
> > > un-initialize panel: -22
> > >
> > >
> > Here is the error messages, these are comes from unprepare by every panel off:
> > [ 121.295290] panel-jdi-fhd-r63452 994000.dsi.0: transmit data failed: -22
> > [ 121.295368] panel-jdi-fhd-r63452 994000.dsi.0: Failed to
> > un-initialize panel: -22
> > [ 184.783019] panel-jdi-fhd-r63452 994000.dsi.0: transmit data failed: -22
> > [ 184.783066] panel-jdi-fhd-r63452 994000.dsi.0: Failed to
> > un-initialize panel: -22
> > with this patch these errors no more.
> > .prepare works because of this flag ctx->panel.prepare_prev_first = true;
>
> The flag should also invert the order of post_disable chain. It well
> might be that the drm/msm/dsi driver shuts down the DSI link too soon.
> Please consider fixing the MSM DSI driver instead.
>
Ok, thank you i look forward to it.
> --
> With best wishes
> Dmitry