hi all
Trying out 2.5.39 on an intel D845GLLY (or ws it D845GLAD) board, I get this
cute little panic. Attached are lspci -vvv and .config.
roy
Unable to handle kernel paging request at virtual address 56112e2c
dec84f28
*pde = 00000000
Oops: 0002
CPU: 0
EIP: 0060:[<dec84f28>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010207
eax: dec84f60 ebx: dec86820 ecx: dec86904 edx: dec86820
esi: 00000000 edi: c0302850 ebp: 00000001 esp: deedde1c
ds: 0068 es: 0068 ss: 0068
Stack: c014ed99 dec86820 0000002d 00000000 0000002d c039c5c0 dec86820 c014f6f4
dec86820 dec86820 dec86820 c014f784 dec86820 dec80220 c014d866 dec86820
00002e87 c0118bff 00002e87 00002e87 deeed3a0 decc8c00 c0150ca2 dec80220
[<c014ed99>]clear_inode+0x69/0xb0
[<c014f6f4>]generic_forget_inode+0xe4/0x100
[<c014f784>]iput+0x54/0x60
[<c014d866>]dput+0xf6/0x150
[<c0118bff>]call_console_drivers+0xdf/0xf0
[<c0150ca2>]__mntput+0x12/0xe0
[<c0255c12>]usb_get_sb+0xe2/0xf0
[<c0118d83>]printk+0x103/0x110
[<c0255d48>]create_special_files+0x128/0x140
[<c0255e06>]usbfs_add_bus+0x16/0xe0
[<c024fd24>]usb_register_bus+0xf4/0x110
[<c0252ad2>]usb_hcd_pci_probe+0x372/0x3a0
[<c01aaf5d>]pci_device_probe+0x3d/0x60
[<c01e8c28>]probe+0x18/0x30
[<c01e8c94>]found_match+0x24/0x50
[<c01e8da5>]do_driver_attach+0x35/0x40
[<c01e953a>]bus_for_each_dev+0x4a/0x90
[<c01e8dc3>]driver_attach+0x13/0x20
[<c01e8d70>]do_driver_attach+0x0/0x40
[<c01e981a>]driver_register+0x5a/0x70
[<c01ab066>]pci_register_driver+0x36/0x50
[<c0246595>]cdrom_sysctl_register+0x15/0x70
[<c0105030>]init+0x0/0x160
[<c0105051>]init+0x21/0x160
[<c0105030>]init+0x0/0x160
[<c0107015>]kernel_thread_helper+0x5/0x10
Code: 00 88 cc de 48 77 7e c1 48 77 7e c1 00 a4 c8 de 80 81 40 40
-----------------------------------------------------------------
bash-2.05# lspci -vvv
00:00.0 Class 0600: 8086:2560 (rev 01)
Subsystem: 8086:2560
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [1105]
00:02.0 Class 0300: 8086:2562 (rev 01)
Subsystem: 8086:4c59
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 Class 0c03: 8086:24c2 (rev 01)
Subsystem: 8086:4c59
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at e800 [size=32]
00:1d.1 Class 0c03: 8086:24c4 (rev 01)
Subsystem: 8086:4c59
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at e880 [size=32]
00:1d.2 Class 0c03: 8086:24c7 (rev 01)
Subsystem: 8086:4c59
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at ec00 [size=32]
00:1d.7 Class 0c03: 8086:24cd (rev 01) (prog-if 20)
Subsystem: 8086:4c59
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 9
Region 0: Memory at ffa7fc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3h
ot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
00:1e.0 Class 0604: 8086:244e (rev 81)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: e6a00000-e6afffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 Class 0601: 8086:24c0 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Step
ping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 Class 0101: 8086:24cb (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: 8086:4c59
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at <unassigned> [size=8]
Region 1: I/O ports at <unassigned> [size=4]
Region 2: I/O ports at <unassigned> [size=8]
Region 3: I/O ports at <unassigned> [size=4]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 1ff00000 (32-bit, non-prefetchable) [disabled]
[size
=1K]
00:1f.3 Class 0c05: 8086:24c3 (rev 01)
Subsystem: 8086:4c59
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
00:1f.5 Class 0401: 8086:24c5 (rev 01)
Subsystem: 8086:0302
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at e400 [size=256]
Region 1: I/O ports at e080 [size=64]
Region 2: Memory at ffa7f800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at ffa7f400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3h
ot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 Class 0180: 105a:4d68 (rev 02) (prog-if 85)
Subsystem: 105a:4d68
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at d880 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d480 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: Memory at ff8fc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at ff8f8000 [disabled] [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:01.0 Class 0180: 105a:4d68 (rev 02) (prog-if 85)
Subsystem: 105a:4d68
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at d080 [size=8]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at df00 [size=8]
Region 3: I/O ports at de80 [size=4]
Region 4: I/O ports at de00 [size=16]
Region 5: Memory at ff8f4000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at ff8f0000 [disabled] [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:02.0 Class 0200: 8086:100e (rev 02)
Subsystem: 8086:002e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Step
ping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ff8c0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ff8a0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dd80 [size=64]
Expansion ROM at ff880000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable
-
Address: 0000000000000000 Data: 0000
01:08.0 Class 0200: 8086:1039 (rev 81)
Subsystem: 8086:3013
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Step
ping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ff8ef000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at dd00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
bash-2.05#
--
Roy Sigurd Karlsbakk, Datavaktmester
ProntoTV AS - http://www.pronto.tv/
Tel: +47 9801 3356
Computers are like air conditioners.
They stop working when you open Windows.
did anyone see this?
On Sunday 29 September 2002 18:56, Roy Sigurd Karlsbakk wrote:
> hi all
>
> Trying out 2.5.39 on an intel D845GLLY (or ws it D845GLAD) board, I get
> this cute little panic. Attached are lspci -vvv and .config.
>
> roy
>
> Unable to handle kernel paging request at virtual address 56112e2c
> dec84f28
> *pde = 00000000
> Oops: 0002
> CPU: 0
> EIP: 0060:[<dec84f28>] Not tainted
> Using defaults from ksymoops -t elf32-i386 -a i386
> EFLAGS: 00010207
> eax: dec84f60 ebx: dec86820 ecx: dec86904 edx: dec86820
> esi: 00000000 edi: c0302850 ebp: 00000001 esp: deedde1c
> ds: 0068 es: 0068 ss: 0068
> Stack: c014ed99 dec86820 0000002d 00000000 0000002d c039c5c0 dec86820
> c014f6f4 dec86820 dec86820 dec86820 c014f784 dec86820 dec80220 c014d866
> dec86820 00002e87 c0118bff 00002e87 00002e87 deeed3a0 decc8c00 c0150ca2
> dec80220 [<c014ed99>]clear_inode+0x69/0xb0
> [<c014f6f4>]generic_forget_inode+0xe4/0x100
> [<c014f784>]iput+0x54/0x60
> [<c014d866>]dput+0xf6/0x150
> [<c0118bff>]call_console_drivers+0xdf/0xf0
> [<c0150ca2>]__mntput+0x12/0xe0
> [<c0255c12>]usb_get_sb+0xe2/0xf0
> [<c0118d83>]printk+0x103/0x110
> [<c0255d48>]create_special_files+0x128/0x140
> [<c0255e06>]usbfs_add_bus+0x16/0xe0
> [<c024fd24>]usb_register_bus+0xf4/0x110
> [<c0252ad2>]usb_hcd_pci_probe+0x372/0x3a0
> [<c01aaf5d>]pci_device_probe+0x3d/0x60
> [<c01e8c28>]probe+0x18/0x30
> [<c01e8c94>]found_match+0x24/0x50
> [<c01e8da5>]do_driver_attach+0x35/0x40
> [<c01e953a>]bus_for_each_dev+0x4a/0x90
> [<c01e8dc3>]driver_attach+0x13/0x20
> [<c01e8d70>]do_driver_attach+0x0/0x40
> [<c01e981a>]driver_register+0x5a/0x70
> [<c01ab066>]pci_register_driver+0x36/0x50
> [<c0246595>]cdrom_sysctl_register+0x15/0x70
> [<c0105030>]init+0x0/0x160
> [<c0105051>]init+0x21/0x160
> [<c0105030>]init+0x0/0x160
> [<c0107015>]kernel_thread_helper+0x5/0x10
> Code: 00 88 cc de 48 77 7e c1 48 77 7e c1 00 a4 c8 de 80 81 40 40
>
> -----------------------------------------------------------------
> bash-2.05# lspci -vvv
> 00:00.0 Class 0600: 8086:2560 (rev 01)
> Subsystem: 8086:2560
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [e4] #09 [1105]
>
> 00:02.0 Class 0300: 8086:2562 (rev 01)
> Subsystem: 8086:4c59
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> Region 1: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
> Capabilities: [d0] Power Management version 1
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot
> -,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1d.0 Class 0c03: 8086:24c2 (rev 01)
> Subsystem: 8086:4c59
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at e800 [size=32]
>
> 00:1d.1 Class 0c03: 8086:24c4 (rev 01)
> Subsystem: 8086:4c59
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 11
> Region 4: I/O ports at e880 [size=32]
>
> 00:1d.2 Class 0c03: 8086:24c7 (rev 01)
> Subsystem: 8086:4c59
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 5
> Region 4: I/O ports at ec00 [size=32]
>
> 00:1d.7 Class 0c03: 8086:24cd (rev 01) (prog-if 20)
> Subsystem: 8086:4c59
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 9
> Region 0: Memory at ffa7fc00 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3h
> ot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [2080]
>
> 00:1e.0 Class 0604: 8086:244e (rev 81)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR+
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: ff800000-ff8fffff
> Prefetchable memory behind bridge: e6a00000-e6afffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1f.0 Class 0601: 8086:24c0 (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.1 Class 0101: 8086:24cb (rev 01) (prog-if 8a [Master SecP PriP])
> Subsystem: 8086:4c59
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 5
> Region 0: I/O ports at <unassigned> [size=8]
> Region 1: I/O ports at <unassigned> [size=4]
> Region 2: I/O ports at <unassigned> [size=8]
> Region 3: I/O ports at <unassigned> [size=4]
> Region 4: I/O ports at ffa0 [size=16]
> Region 5: Memory at 1ff00000 (32-bit, non-prefetchable) [disabled]
> [size
> =1K]
>
> 00:1f.3 Class 0c05: 8086:24c3 (rev 01)
> Subsystem: 8086:4c59
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 11
> Region 4: I/O ports at e000 [size=32]
>
> 00:1f.5 Class 0401: 8086:24c5 (rev 01)
> Subsystem: 8086:0302
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 11
> Region 0: I/O ports at e400 [size=256]
> Region 1: I/O ports at e080 [size=64]
> Region 2: Memory at ffa7f800 (32-bit, non-prefetchable) [size=512]
> Region 3: Memory at ffa7f400 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3h
> ot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 Class 0180: 105a:4d68 (rev 02) (prog-if 85)
> Subsystem: 105a:4d68
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 32 (1000ns min, 4500ns max), cache line size 08
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at dc00 [size=8]
> Region 1: I/O ports at d880 [size=4]
> Region 2: I/O ports at d800 [size=8]
> Region 3: I/O ports at d480 [size=4]
> Region 4: I/O ports at d400 [size=16]
> Region 5: Memory at ff8fc000 (32-bit, non-prefetchable) [size=16K]
> Expansion ROM at ff8f8000 [disabled] [size=16K]
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot
> -,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:01.0 Class 0180: 105a:4d68 (rev 02) (prog-if 85)
> Subsystem: 105a:4d68
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Step
> ping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 32 (1000ns min, 4500ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at d080 [size=8]
> Region 1: I/O ports at d000 [size=4]
> Region 2: I/O ports at df00 [size=8]
> Region 3: I/O ports at de80 [size=4]
> Region 4: I/O ports at de00 [size=16]
> Region 5: Memory at ff8f4000 (32-bit, non-prefetchable) [size=16K]
> Expansion ROM at ff8f0000 [disabled] [size=16K]
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot
> -,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:02.0 Class 0200: 8086:100e (rev 02)
> Subsystem: 8086:002e
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Step
> ping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 32 (63750ns min), cache line size 08
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at ff8c0000 (32-bit, non-prefetchable) [size=128K]
> Region 1: Memory at ff8a0000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at dd80 [size=64]
> Expansion ROM at ff880000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot
> +,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [e4] PCI-X non-bridge device.
> Command: DPERE- ERO+ RBC=0 OST=0
> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
> DC=simple,
> DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
> Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
> Enable
> -
> Address: 0000000000000000 Data: 0000
>
> 01:08.0 Class 0200: 8086:1039 (rev 81)
> Subsystem: 8086:3013
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Step
> ping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort
> - <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min, 14000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at ff8ef000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at dd00 [size=64]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot
> +,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> bash-2.05#
--
Roy Sigurd Karlsbakk, Datavaktmester
ProntoTV AS - http://www.pronto.tv/
Tel: +47 9801 3356
Computers are like air conditioners.
They stop working when you open Windows.