Here is the clip of the boot message from trying to start 2.5.40-ac3
kernel. gcc-3.2 used. I can do whatever setup and configuration you
require.
mounting root filesystem
request_module[block-major-33]: not ready
mount: error 6 mounting ext 3
pivotroot: pivot_root(/sysroot,/sysroot/initrd) failed: 2
unmount /initrd/proc failed: 2
Freeing unused Kernel memory: 176K freed
Kernel panic: no init found
Kernel config:
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_IDEDMA_AUTO=y
#
# File systems
#
CONFIG_QUOTA=y
CONFIG_QUOTACTL=y
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
CONFIG_REISERFS_FS=y
CONFIG_REISERFS_PROC_INFO=y
CONFIG_EXT3_FS=y
CONFIG_JBD=y
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_CRAMFS=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_JFS_FS=y
CONFIG_JFS_DEBUG=y
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
CONFIG_ROMFS_FS=y
CONFIG_EXT2_FS=y
CONFIG_UDF_FS=y
The system has two IBM HDs, one Seagate and a DVD/CRW. It has a IDE
controller on the motherboard and a Promise ATA100 card. Below are the
print outs of the devices:
(hdparm -i /dev/hda)
* /dev/hda1 /mnt/win98 (vfat)
* /dev/hda2 /boot (ext3)
dev/hda:
Model=ST310232A, FwRev=3.09, SerialNo=6BQ032H9
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=20005650
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version: 1 2 3 4
(hdparm -i /dev/hde)
dev/hde:
* /dev/hde1 / (root) (ext3)
* /dev/hde2 swap (swap)
* /dev/hde5 /usr (ext3)
* /dev/hde6 /home (ext3)
dev/hdf: (same drive as hde)
* /dev/hdf1 /usr/src (ext3)
* /dev/hdf2 /mnt/misc_1 (ext3)
Model=IBM-DTLA-307045, FwRev=TX6OA50C, SerialNo=YMDYMT5M619
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=90069840
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5
(lspci -v)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80
[Master])
Flags: bus master, medium devsel, latency 64
[virtual] I/O ports at 01f0
[virtual] I/O ports at 03f4
[virtual] I/O ports at 0170
[virtual] I/O ports at 0374
I/O ports at ffa0 [size=16]
00:14.0 Unknown mass storage controller: Promise Technology, Inc. 20267
(rev 02) Subsystem: Promise Technology, Inc. Ultra100
Flags: bus master, medium devsel, latency 64, IRQ 10
I/O ports at efe0 [size=8]
I/O ports at efac [size=4]
I/O ports at efa0 [size=8]
I/O ports at efa8 [size=4]
I/O ports at ef00 [size=64]
Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at febd0000 [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Stephen Torri
[email protected]