Though I was successfull using my cdwriter under the pre series and win98 it
fails using 2.4.x (i tested it with 2.4.0 and 2.4.2-pre1).
cd writer software in use:
Cdrecord 1.9 (i686-pc-linux-gnu) Copyright (C) 1995-2000 J?rg Schilling
caps according to hdparm:
/dev/hdd:
Model=PHILIPS CDD3610 CD-R/RW, FwRev=V:003.01,
SerialNo=4VO22985121772100210
Config={ Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=3900kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=yes, tPIO={min:208,w/IORDY:127}, tDMA={min:127,rec:127}
PIO modes: pio0 pio1 pio2 pio3
DMA modes: sdma0 sdma1 sdma2 mdma0 *mdma1
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: E-IDE Model: CD-ROM 36X/AKU Rev: U21I
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PHILIPS Model: CDD3610 CD-R/RW Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Detected scsi CD-ROM sr1 at scsi1, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 0x/36x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 2x/6x writer cd/rw xa/form2 cdda tray
VFS: Disk change detected on device sr(11,1)
attempt to access beyond end of device
0b:01: rw=0, want=34, limit=2
isofs_read_super: bread failed, dev=0b:01, iso_blknum=16, block=16
Uniform CD-ROM driver unloaded
hdb: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hdb: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
scsi : aborting command due to timeout : pid 0, scsi1, channel 0, id 1, lun
0 Write (10) 00 00 00 04 5c 00 00 1f 00
hdd: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hdd: irq timeout: status=0xd0 { Busy }
hdd: DMA disabled
hdd: ATAPI reset complete
hdd: irq timeout: status=0xd0 { Busy }
hdd: ATAPI reset complete
hdd: irq timeout: status=0xd0 { Busy }
hdd: status timeout: status=0xd0 { Busy }
hdd: drive not ready for command
hdd: ATAPI reset complete
scsi1 : channel 0 target 1 lun 0 request sense failed, performing reset.
SCSI bus is being reset for host 1 channel 0.
/proc/ide/ide1/hdd/settings:
name value min max mode
---- ----- --- --- ----
bios_cyl 0 0 1023 rw
bios_head 0 0 255 rw
bios_sect 0 0 63 rw
current_speed 33 0 69 rw
ide_scsi 0 0 1 rw
init_speed 33 0 69 rw
io_32bit 0 0 3 rw
keepsettings 0 0 1 rw
log 0 0 1 rw
nice1 1 0 1 rw
number 3 0 3 rw
pio_mode write-only 0 255 w
slow 0 0 1 rw
transform 1 0 3 rw
unmaskirq 0 0 1 rw
using_dma 0 0 1 rw
--
+---- --- -- - - - -
|Frank van de Pol -o)
| [email protected] /\\
| _\_v
|Linux - Why use Windows, since there is a door?