I introduced a regression when reworking the fastreuse port stuff that allows
bind conflicts to occur once a reuseaddr successfully opens on an existing tb.
The root cause is I reversed an if statement which caused us to set the tb as if
there were no owners on the socket if there were, which obviously is not
correct.
Dave could you please queue these changes up for -stable, I've run them through
the net tests and added another test to check for this problem specifically.
Thanks,
Josef
From: Josef Bacik <[email protected]>
In ipv6_rcv_saddr_equal() we need to use inet6_rcv_saddr(sk) for the
ipv6 compare with the fast socket information to make sure we're doing
the proper comparisons.
Fixes: 637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
---
net/ipv4/inet_connection_sock.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/ipv4/inet_connection_sock.c b/net/ipv4/inet_connection_sock.c
index f87f4805e244..a1bf30438bc5 100644
--- a/net/ipv4/inet_connection_sock.c
+++ b/net/ipv4/inet_connection_sock.c
@@ -266,7 +266,7 @@ static inline int sk_reuseport_match(struct inet_bind_bucket *tb,
#if IS_ENABLED(CONFIG_IPV6)
if (tb->fast_sk_family == AF_INET6)
return ipv6_rcv_saddr_equal(&tb->fast_v6_rcv_saddr,
- &sk->sk_v6_rcv_saddr,
+ inet6_rcv_saddr(sk),
tb->fast_rcv_saddr,
sk->sk_rcv_saddr,
tb->fast_ipv6_only,
--
2.7.4
From: Josef Bacik <[email protected]>
When doing my reuseport rework I screwed up and changed a
if (hlist_empty(&tb->owners))
to
if (!hlist_empty(&tb->owners))
This is obviously bad as all of the reuseport/reuse logic was reversed,
which caused weird problems like allowing an ipv4 bind conflict if we
opened an ipv4 only socket on a port followed by an ipv6 only socket on
the same port.
Fixes: b9470c27607b ("inet: kill smallest_size and smallest_port")
Reported-by: Cole Robinson <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
---
net/ipv4/inet_connection_sock.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/ipv4/inet_connection_sock.c b/net/ipv4/inet_connection_sock.c
index a1bf30438bc5..c039c937ba90 100644
--- a/net/ipv4/inet_connection_sock.c
+++ b/net/ipv4/inet_connection_sock.c
@@ -321,7 +321,7 @@ int inet_csk_get_port(struct sock *sk, unsigned short snum)
goto fail_unlock;
}
success:
- if (!hlist_empty(&tb->owners)) {
+ if (hlist_empty(&tb->owners)) {
tb->fastreuse = reuse;
if (sk->sk_reuseport) {
tb->fastreuseport = FASTREUSEPORT_ANY;
--
2.7.4
From: Josef Bacik <[email protected]>
We need to set the tb->fast_sk_family properly so we can use the proper
comparison function for all subsequent reuseport bind requests.
Fixes: 637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
---
net/ipv4/inet_connection_sock.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/net/ipv4/inet_connection_sock.c b/net/ipv4/inet_connection_sock.c
index b9c64b40a83a..f87f4805e244 100644
--- a/net/ipv4/inet_connection_sock.c
+++ b/net/ipv4/inet_connection_sock.c
@@ -328,6 +328,7 @@ int inet_csk_get_port(struct sock *sk, unsigned short snum)
tb->fastuid = uid;
tb->fast_rcv_saddr = sk->sk_rcv_saddr;
tb->fast_ipv6_only = ipv6_only_sock(sk);
+ tb->fast_sk_family = sk->sk_family;
#if IS_ENABLED(CONFIG_IPV6)
tb->fast_v6_rcv_saddr = sk->sk_v6_rcv_saddr;
#endif
@@ -354,6 +355,7 @@ int inet_csk_get_port(struct sock *sk, unsigned short snum)
tb->fastuid = uid;
tb->fast_rcv_saddr = sk->sk_rcv_saddr;
tb->fast_ipv6_only = ipv6_only_sock(sk);
+ tb->fast_sk_family = sk->sk_family;
#if IS_ENABLED(CONFIG_IPV6)
tb->fast_v6_rcv_saddr = sk->sk_v6_rcv_saddr;
#endif
--
2.7.4