2006-01-26 07:58:41

by Prakash Punnoor

[permalink] [raw]
Subject: Issues with uli526x networking module

Hi,

I have some problems with the uli526x driver. (I cc'ed the tulip maintainer,
as the driver is found in this category.)

- It doesn't detect link when cable is plugged in, if module/driver is loaded
with no cable attached. I have to rmmod the module, plug in cable, insmod the
module and then set up the interface to get it running. That's the only
reason I compiled this driver as a module...(BTW, it is not AMD64 related, as
I experienced this also in x86.)

- dhcpcd doesn't work. dhclient does though (but it is slow, I can't find the
correct parameters to speed it up). The former gets no response from the dhcp
server. I don't think it is a problem with the dhcp server, as dhcpcd works
from a notebook with some dlink pcmcia 10mbit interface.


Beside above, it seems to work fine, though.


attached some infos which might be needed:

Bootdata ok (command line is root=/dev/sda5 elevator=cfq quiet)
Linux version 2.6.15 (root@varma) (gcc-Version 3.4.5 (Gentoo 3.4.5)) #1 SMP
PREEMPT Thu Jan 12 14:50:12 CET 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data)
BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000180000000 (usable)
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f9bb0
ACPI: RSDT (v001 A M I OEMRSDT 0x12000506 MSFT 0x00000097) @
0x000000007ffb0000
ACPI: FADT (v002 A M I OEMFACP 0x12000506 MSFT 0x00000097) @
0x000000007ffb0200
ACPI: MADT (v001 A M I OEMAPIC 0x12000506 MSFT 0x00000097) @
0x000000007ffb0390
ACPI: OEMB (v001 A M I AMI_OEM 0x12000506 MSFT 0x00000097) @
0x000000007ffc0040
ACPI: DSDT (v001 939M2 939M2150 0x00000150 INTL 0x02002026) @
0x0000000000000000
On node 0 totalpages: 1025626
DMA zone: 2674 pages, LIFO batch:0
DMA32 zone: 505832 pages, LIFO batch:31
Normal zone: 517120 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 17, address 0xfec10000, GSI 24-39
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7f7c0000)
Checking aperture...
CPU 0: aperture @ d0000000 size 256 MB
Built 1 zonelists
Kernel command line: root=/dev/sda5 elevator=cfq quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.122 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 4095664k/6291456k available (3159k kernel code, 97584k reserved, 1267k
data, 212k init)
Calibrating delay using timer specific routine.. 4003.11 BogoMIPS
(lpj=2001559)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3999.60 BogoMIPS
(lpj=1999803)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 3 cycles, maxerr 534 cycles)
Brought up 2 CPUs
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-083f claimed by ali7101 ACPI
Boot video device is 0000:03:00.0
PCI: Transparent bridge - 0000:00:06.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HTT_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEB1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEB2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 20
Setting up ULi AGP.
agpgart: AGP aperture is 256M @ 0xd0000000
PCI-DMA: Reserving 128MB of IOMMU area in the AGP aperture
pnp: 00:0b: ioport range 0x290-0x29f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fc700000-fc7fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: fc800000-fc8fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
IO window: disabled.
MEM window: fc900000-fe9fffff
PREFETCH window: aff00000-bfefffff
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: fea00000-feafffff
PREFETCH window: disabled.
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 29 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 34 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
IA-32 Microcode Update Driver: v1.14 <[email protected]>
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Installing knfsd (copyright (C) 1996 [email protected]).
NTFS driver 2.1.25 [Flags: R/W].
fuse init (API version 7.3)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 29 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 34 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
lp0: console ready
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:12.0
GSI 18 sharing vector 0xD1 and IRQ 18
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 19 (level, low) -> IRQ 209
ALI15X3: chipset revision 199
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
libata version 1.20 loaded.
sata_uli 0000:00:12.1: version 0.5
ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 19 (level, low) -> IRQ 209
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE082 bmdma 0xD880 irq 209
ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD888 irq 209
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663
88:007f
ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_uli
ata2: no device found (phy stat 00000000)
scsi1 : sata_uli
Vendor: ATA Model: Maxtor 7L250S0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usbmon: debugfs is not available
GSI 19 sharing vector 0xD9 and IRQ 19
ACPI: PCI Interrupt 0000:00:13.3[D] -> GSI 23 (level, low) -> IRQ 217
ehci_hcd 0000:00:13.3: EHCI Host Controller
ehci_hcd 0000:00:13.3: debug port 1
ehci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.3: irq 217, io mem 0xfebfe800
ehci_hcd 0000:00:13.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
GSI 20 sharing vector 0xE1 and IRQ 20
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 20 (level, low) -> IRQ 225
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 225, io mem 0xfebfd000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
GSI 21 sharing vector 0xE9 and IRQ 21
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 21 (level, low) -> IRQ 233
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 233, io mem 0xfebfc000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
GSI 22 sharing vector 0x32 and IRQ 22
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 22 (level, low) -> IRQ 50
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 50, io mem 0xfebfb000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
I2O subsystem v1.288
i2o: max drivers = 8
I2O Configuration OSM v1.248
I2O Bus Adapter OSM v$Rev$
I2O Block Device OSM v1.287
I2O SCSI Peripheral OSM v1.282
I2O ProcFS OSM v1.145
i2c /dev entries driver
ali1563: SMBus control = 0403
ali1563_probe: Returning 0
input: AT Translated Set 2 keyboard as /class/input/input0
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07
13:30:21 2005 UTC).
GSI 23 sharing vector 0x3A and IRQ 23
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 58
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
AC'97 1 does not respond - RESET
AC'97 1 access is not valid [0xffffffff], removing mixer.
Unable to initialize codec #1
intel8x0_measure_ac97_clock: measured 50953 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: ALi M5455 with ALC850 at 0x0, irq 58
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0xa (1300 mV)
cpu_init done, current fid 0xc, vid 0x8
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 212k freed
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
GSI 24 sharing vector 0x42 and IRQ 24
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 17 (level, low) -> IRQ 66
eth0: ULi M5263 at pci0000:00:11.0, 00:13:8f:5d:2e:ea, irq 66.
ReiserFS: sda6: found reiserfs format "3.6" with standard journal
ReiserFS: sda6: using ordered data mode
ReiserFS: sda6: journal params: device sda6, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda6: checking transaction log (sda6)
ReiserFS: sda6: Using r5 hash to sort names
uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
mtrr: type mismatch for b0000000,2000000 old: write-back new: write-combining


00:00.0 Host bridge: ALi Corporation M1695 K8 Northbridge [PCI Express and
HyperTransport]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [40] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut-
LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit
DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 1.05
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE+ OFE+ EOCFE+ RFE+ CRCFE+
SERRFE- CF- RE- PNFE+ ONFE+ EOCNFE+ RNFE- CRCNFE+ SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [5c] HyperTransport: MSI Mapping
Capabilities: [68] HyperTransport: UnitID Clumping
Capabilities: [74] HyperTransport: Interrupt Discovery and
Configuration
Capabilities: [7c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable-
Address: 00000000fee00000 Data: 0000
00: b9 10 95 16 07 00 10 00 00 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
40: 08 5c 60 00 20 00 11 11 20 00 11 10 25 05 f5 00
50: 02 00 f5 00 ff ff 7f 5c 00 00 00 00 08 68 00 a8
60: 00 00 e0 fe 00 00 00 00 08 74 00 90 00 00 00 00
70: 00 00 00 00 08 7c 00 80 67 03 b1 f8 05 00 82 00
80: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:01.0 PCI bridge: ALi Corporation PCI Express Root Port (prog-if 00 [Normal
decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc700000-fc7fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 40c1
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <2us, L1 <32us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [7c] HyperTransport: MSI Mapping
Capabilities: [88] HyperTransport: Revision ID: 1.05
00: b9 10 4b 52 06 05 10 00 00 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
20: 70 fc 70 fc f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 03 00
40: 01 48 02 c8 00 00 00 00 05 58 83 00 00 00 e0 fe
50: 00 00 00 00 c1 40 00 00 10 7c 41 01 20 00 00 00
60: 10 28 18 00 01 dd 02 00 00 00 10 10 00 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 08 88 00 a8
80: 00 00 e0 fe 00 00 00 00 08 00 25 88 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 03 00 00 00 00 00 0c 02 08 3f 63 ed 70 2c
b0: 00 00 00 00 00 11 00 00 00 00 00 00 01 00 3f 1f
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 d0 0c 40 01 04 73 00 00 00 00 00 d1 00 77 30
e0: 00 00 00 00 01 00 00 00 01 00 00 00 26 38 18 d0
f0: 01 50 94 2d 59 41 50 86 06 38 ef 53 40 0e 66 c1

00:02.0 PCI bridge: ALi Corporation PCI Express Root Port (prog-if 00 [Normal
decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc800000-fc8fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 40c9
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s L1, Port 0
Link: Latency L0s <2us, L1 <32us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x2
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [7c] HyperTransport: MSI Mapping
Capabilities: [88] HyperTransport: Revision ID: 1.05
00: b9 10 4c 52 06 05 10 00 00 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 f0 00 00 00
20: 80 fc 80 fc f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 03 00
40: 01 48 02 c8 00 00 00 00 05 58 83 00 00 00 e0 fe
50: 00 00 00 00 c9 40 00 00 10 7c 41 01 20 00 00 00
60: 10 28 18 00 21 dc 02 00 00 00 10 10 00 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 08 88 00 a8
80: 00 00 e0 fe 00 00 00 00 08 00 25 88 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 03 00 00 00 00 00 0c 02 09 3f 63 ed 70 2c
b0: 00 00 00 00 00 11 00 00 04 00 00 00 01 00 3f 1f
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 d0 0c 40 01 04 73 00 00 00 00 00 d1 00 77 30
e0: 00 00 00 00 01 00 00 00 01 00 00 00 64 b1 41 40
f0: d7 2e 91 66 7e 1d fc 1a cc 24 dc 44 22 2d 40 a4

00:04.0 Host bridge: ALi Corporation M1689 K8 Northbridge [Super K8 Single
Chip]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [40] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=4 UnitCnt=1 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=8bit DwFcOut- LWI=16bit
DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.04
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [60] HyperTransport: Interrupt Discovery and
Configuration
Capabilities: [80] AGP version 3.0
Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00: b9 10 89 16 06 01 10 00 00 00 00 06 00 00 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
40: 08 60 24 00 20 00 01 01 d0 00 00 00 24 05 35 00
50: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 08 80 32 80 66 03 42 f8 00 00 00 00 00 05 17 50
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 02 00 30 00 07 02 00 1b 00 00 00 00 0a 00 20 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:05.0 PCI bridge: ALi Corporation AGP8X Controller (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc900000-fe9fffff
Prefetchable memory behind bridge: aff00000-bfefffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00: b9 10 46 52 07 01 20 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 03 03 40 f0 00 20 22
20: 90 fc 90 fe f0 af e0 bf 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0b 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 20 78 00 c0 00 20 20 20 20 20 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 11 00 00 00 00 11 00 01 20 1a
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:06.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge (prog-if 01
[Subtractive decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00: b9 10 49 52 06 01 00 00 00 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 04 04 20 f0 00 00 22
20: a0 fe a0 fe f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00
40: 00 80 00 78 00 00 00 00 80 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:07.0 ISA bridge: ALi Corporation M1563 HyperTransport South Bridge (rev 70)
Subsystem: ASRock Incorporation Unknown device 1563
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 6000ns max)
00: b9 10 63 15 0f 00 00 02 70 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 63 15
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 18
40: f7 e4 00 09 3d fa 00 00 00 00 00 00 03 c0 00 10
50: 02 00 02 00 0d 09 01 80 ff 3c fb 67 a1 60 10 00
60: d8 f8 c0 f2 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 07 63 15 00 0f 00 00 00 00 00 20 00 00 00 00
80: 03 04 00 00 21 0f cc dd ee 99 aa 99 00 bb 00 5f
90: 80 03 83 00 00 00 00 00 1e 00 00 00 00 00 e0 fe
a0: 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: df 80 01 00 c0 00 f0 08 5f 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:07.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
Subsystem: ASRock Incorporation Unknown device 7101
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00: b9 10 01 71 00 00 00 02 00 00 80 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 01 71
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 40 00 00 00 00 20 00 08 7a 00 00 00 00 00 00
50: 00 07 ff 58 00 00 00 00 00 df 0f 10 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 ff 3f 3f 3f
70: ff 07 00 00 00 00 00 08 76 88 b0 08 3c fe ff 00
80: 32 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 a0 aa 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: ff 44 80 20 00 ff ff 07 00 00 28 70 40 9b 02 00
c0: 12 00 10 10 00 00 00 00 00 00 ff 00 4b 00 00 00
d0: 00 42 04 00 40 00 22 04 4c 2f 00 00 00 00 00 00
e0: 00 08 00 00 0e 29 cb 55 b4 00 01 00 00 00 00 36
f0: 00 00 00 00 00 00 00 f0 00 00 00 00 00 00 00 00

00:08.0 Multimedia audio controller: ALi Corporation M5455 PCI AC-Link
Controller Audio Device (rev 20)
Subsystem: ASRock Incorporation Unknown device 0850
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (16000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 58
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: b9 10 55 54 17 00 10 02 20 00 01 04 10 20 00 00
10: 01 e8 00 00 00 f0 bf fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 50 08
30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 40 00
40: 01 00 22 e6 00 00 00 00 00 00 00 00 00 00 00 00
50: 49 18 50 08 10 00 c4 00 40 00 07 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 57 54 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:11.0 Ethernet controller: ALi Corporation M5263 Ethernet Controller (rev
40)
Subsystem: ASRock Incorporation Unknown device 5263
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 66
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at febfec00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: b9 10 63 52 07 01 10 02 40 00 00 02 08 20 00 00
10: 01 e4 00 00 00 ec bf fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 63 52
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 14 28
40: 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 22 c0 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:12.0 IDE interface: ALi Corporation M5229 IDE (rev c7) (prog-if 8a [Master
SecP PriP])
Subsystem: ASRock Incorporation Unknown device 5229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 209
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at ff00 [size=16]
00: b9 10 29 52 05 00 a0 02 c7 8a 01 01 00 20 80 00
10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
20: 01 ff 00 00 00 00 00 00 00 00 00 00 49 18 29 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
40: 00 00 00 7a 4d 10 00 c0 00 80 64 c9 00 00 ba 1a
50: 00 00 00 01 50 55 4a 44 01 31 31 00 00 00 00 00
60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 01 00 01 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:12.1 IDE interface: ALi Corporation ULi 5289 SATA (rev 10) (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: ASRock Incorporation Unknown device 5289
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 10
Interrupt: pin A routed to IRQ 209
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e080 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d880 [size=16]
00: b9 10 89 52 05 01 a0 02 10 8f 01 01 10 20 80 00
10: 01 ec 00 00 81 e0 00 00 01 e0 00 00 01 dc 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 49 18 89 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 06 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 1f 00 00 03 10 01 00 00 00 68 00 68 00
90: 13 01 00 00 01 04 8d 04 00 03 00 00 00 00 00 00
a0: 00 00 00 00 00 04 80 00 00 03 00 00 00 00 00 00
b0: 00 00 00 00 88 b1 0e 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:13.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: ASRock Incorporation Unknown device 5237
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 225
Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
10: 00 d0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 50
40: 00 00 1f 00 e0 40 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:13.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: ASRock Incorporation Unknown device 5237
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size 10
Interrupt: pin B routed to IRQ 233
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
10: 00 c0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 50
40: 00 00 1f 00 e0 48 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:13.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: ASRock Incorporation Unknown device 5237
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size 10
Interrupt: pin C routed to IRQ 50
Region 0: Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
10: 00 b0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 50
40: 00 00 1f 00 e0 48 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:13.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if
20 [EHCI])
Subsystem: ASRock Incorporation Unknown device 5239
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), Cache Line Size 10
Interrupt: pin D routed to IRQ 217
Region 0: Memory at febfe800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: b9 10 39 52 16 01 b0 02 01 20 03 0c 10 20 80 00
10: 00 e8 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 39 52
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 10 20
40: 20 03 00 c4 80 02 10 c4 00 00 00 00 00 00 00 00
50: 01 58 02 c8 00 00 00 00 0a 00 90 20 00 00 00 00
60: 20 20 7f 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 00 00 01 00 00 08 c0 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
60: 00 00 01 00 e4 00 00 00 20 c8 00 0f 1c 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 08 00 01 21 20 00 11 11 22 05 75 80 02 00 00 00
90: 56 04 51 02 00 00 ff 00 07 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 03 00 00 00 00 00 7f 01 00 00 00 00 01 00 00 00
50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
80: 03 00 e0 00 00 ff ef 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 03 0a 00 00 00 0b 00 00 03 00 80 00 00 ff ff 00
c0: 13 10 00 00 00 f0 ff 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 03 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 00 00 00 01 00 00 04 01 00 00 10 01 00 00 14
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 fe e0 03 00 fe e0 03 00 fe e0 03 00 fe e0 03
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 77 00 00 00 00 00 00 00 45 34 82 13 31 0b 00 00
90: 80 8e 05 38 07 07 7b 3e 00 00 00 00 0d 02 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 71 9f 5e 3b 71 00 00 00 ff 31 00 00 bd ae fb ff
c0: 00 80 03 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 15 4c f1 f0 24 80 c8 20 4d eb fe f4 10 90 00 1a
e0: 45 1c 34 00 11 18 40 40 d3 55 bf b7 1f 6d 3c fd
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: ff 3b 00 00 40 00 00 08 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 80 90 45 01
60: 8c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 11 01 02 51 11 80 00 50 00 38 00 08 1a 22 00 00
80: 00 00 07 23 13 21 13 21 00 00 00 00 00 00 00 00
90: 07 00 00 00 68 00 00 00 00 80 7f 01 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 37 00 00 00 00 80 4d 5c
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 01 a7 0d 00 10 27 60 20 00 00 00 00
e0: 00 00 00 00 20 07 4e 0e 19 11 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

03:00.0 VGA compatible controller: nVidia Corporation NV15 [GeForce2 GTS/Pro]
(rev a3) (prog-if 00 [VGA])
Subsystem: Elsa AG Gladiac
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at b0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fe9f0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00: de 10 50 01 07 00 b0 02 a3 00 00 03 00 20 00 00
10: 00 00 00 fd 08 00 00 b0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 48 10 50 0c
30: 00 00 9f fe 60 00 00 00 00 00 00 00 05 01 05 01
40: 48 10 50 0c 02 00 20 00 17 00 00 1f 00 00 00 00
50: 01 00 00 00 01 00 00 00 ce d6 23 00 0f 00 00 00
60: 01 44 01 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.15
# Thu Jan 12 14:47:37 2006
#
CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Block layer
#
CONFIG_LBD=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
CONFIG_MK8=y
# CONFIG_MPSC is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_MICROCODE=y
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
CONFIG_SMP=y
# CONFIG_SCHED_SMT is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
# CONFIG_NUMA is not set
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y
CONFIG_NR_CPUS=2
# CONFIG_HOTPLUG_CPU is not set
CONFIG_HPET_TIMER=y
CONFIG_X86_PM_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_GART_IOMMU=y
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_INTEL=y
CONFIG_X86_MCE_AMD=y
CONFIG_PHYSICAL_START=0x100000
CONFIG_KEXEC=y
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ISA_DMA_API=y
CONFIG_GENERIC_PENDING_IRQ=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=y
CONFIG_ACPI_HOTKEY=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_ACPI_CONTAINER=y

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y

#
# CPUFreq processor drivers
#
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
CONFIG_X86_ACPI_CPUFREQ=y

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
# CONFIG_X86_SPEEDSTEP_LIB is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_UNORDERED_IO=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY_PROC=y
# CONFIG_PCI_DEBUG is not set

#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_IA32_EMULATION=y
# CONFIG_IA32_AOUT is not set
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_UID16=y

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set

#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set

#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
# CONFIG_PARPORT_SERIAL is not set
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
# CONFIG_IDE_GENERIC is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
CONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set

#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
CONFIG_SCSI_SATA=y
CONFIG_SCSI_SATA_AHCI=y
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
# CONFIG_SCSI_SATA_MV is not set
# CONFIG_SCSI_SATA_NV is not set
# CONFIG_SCSI_PDC_ADMA is not set
# CONFIG_SCSI_SATA_QSTOR is not set
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIL24 is not set
# CONFIG_SCSI_SATA_SIS is not set
CONFIG_SCSI_SATA_ULI=y
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
CONFIG_SCSI_SATA_INTEL_COMBINED=y
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
CONFIG_I2O=y
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_EXT_ADAPTEC_DMA64=y
CONFIG_I2O_CONFIG=y
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=y
CONFIG_I2O_BLOCK=y
CONFIG_I2O_SCSI=y
CONFIG_I2O_PROC=y

#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# PHY device support
#
# CONFIG_PHYLIB is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set

#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
CONFIG_ULI526X=m
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1280
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1024
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=y
CONFIG_LP_CONSOLE=y
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
# CONFIG_AGP_INTEL is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set

#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
CONFIG_I2C_ALI1563=y
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_ISA=y
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set

#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_RTC_X1205_I2C is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Hardware Monitoring support
#
CONFIG_HWMON=y
CONFIG_HWMON_VID=y
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
CONFIG_SENSORS_LM75=y
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83L785TS is not set
CONFIG_SENSORS_W83627HF=y
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set

#
# Multimedia Capabilities Port drivers
#

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set

#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Sound
#
CONFIG_SOUND=y

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_AC97_CODEC=y
CONFIG_SND_AC97_BUS=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_SEQ_DUMMY=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_HDA_INTEL is not set

#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_SUSPEND=y
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set

#
# USB Input Devices
#
# CONFIG_USB_HID is not set

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_ITMTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set

#
# Video4Linux support is needed for USB Multimedia device support
#

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y

#
# USB port drivers
#
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
# CONFIG_MMC is not set

#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set

#
# SN Devices
#

#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set

#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
CONFIG_FUSE_FS=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=y
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=y
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y

#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
# CONFIG_KPROBES is not set

#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=15
# CONFIG_DETECT_SOFTLOCKUP is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_INIT_DEBUG is not set
# CONFIG_IOMMU_DEBUG is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
CONFIG_CRYPTO=y
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES_X86_64 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set

#
# Hardware crypto devices
#

#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y

--
(?= =?)
//\ Prakash Punnoor /\\
V_/ \_V


Attachments:
(No filename) (80.13 kB)
(No filename) (189.00 B)
Download all attachments

2006-01-26 11:14:38

by Nigel Cunningham

[permalink] [raw]
Subject: Re: Issues with uli526x networking module

Hi.

On Thursday 26 January 2006 18:00, Prakash Punnoor wrote:
> Hi,
>
> I have some problems with the uli526x driver. (I cc'ed the tulip
> maintainer, as the driver is found in this category.)
>
> - It doesn't detect link when cable is plugged in, if module/driver is
> loaded with no cable attached. I have to rmmod the module, plug in cable,
> insmod the module and then set up the interface to get it running. That's
> the only reason I compiled this driver as a module...(BTW, it is not AMD64
> related, as I experienced this also in x86.)
>
> - dhcpcd doesn't work. dhclient does though (but it is slow, I can't find
> the correct parameters to speed it up). The former gets no response from
> the dhcp server. I don't think it is a problem with the dhcp server, as
> dhcpcd works from a notebook with some dlink pcmcia 10mbit interface.
>
>
> Beside above, it seems to work fine, though.

I have one too, and have done some work toward implementing power management
support (working, but needs further work). I've noticed the link issue and
will see if I can address it too. Regarding dhcpcd, I haven't used it, but
will see if I can test before sending the patches to Jeff and to Peer Chen.

Regards,

Nigel

>
> attached some infos which might be needed:
>
> Bootdata ok (command line is root=/dev/sda5 elevator=cfq quiet)
> Linux version 2.6.15 (root@varma) (gcc-Version 3.4.5 (Gentoo 3.4.5)) #1 SMP
> PREEMPT Thu Jan 12 14:50:12 CET 2006
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
> BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data)
> BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS)
> BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
> BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
> BIOS-e820: 0000000100000000 - 0000000180000000 (usable)
> ACPI: RSDP (v000 ACPIAM ) @
> 0x00000000000f9bb0 ACPI: RSDT (v001 A M I OEMRSDT 0x12000506 MSFT
> 0x00000097) @
> 0x000000007ffb0000
> ACPI: FADT (v002 A M I OEMFACP 0x12000506 MSFT 0x00000097) @
> 0x000000007ffb0200
> ACPI: MADT (v001 A M I OEMAPIC 0x12000506 MSFT 0x00000097) @
> 0x000000007ffb0390
> ACPI: OEMB (v001 A M I AMI_OEM 0x12000506 MSFT 0x00000097) @
> 0x000000007ffc0040
> ACPI: DSDT (v001 939M2 939M2150 0x00000150 INTL 0x02002026) @
> 0x0000000000000000
> On node 0 totalpages: 1025626
> DMA zone: 2674 pages, LIFO batch:0
> DMA32 zone: 505832 pages, LIFO batch:31
> Normal zone: 517120 pages, LIFO batch:31
> HighMem zone: 0 pages, LIFO batch:0
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 15:3 APIC version 16
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 15:3 APIC version 16
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
> ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
> IOAPIC[1]: apic_id 3, version 17, address 0xfec10000, GSI 24-39
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Setting APIC routing to flat
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 88000000 (gap: 80000000:7f7c0000)
> Checking aperture...
> CPU 0: aperture @ d0000000 size 256 MB
> Built 1 zonelists
> Kernel command line: root=/dev/sda5 elevator=cfq quiet
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 131072 bytes)
> time.c: Using 3.579545 MHz PM timer.
> time.c: Detected 2000.122 MHz processor.
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Memory: 4095664k/6291456k available (3159k kernel code, 97584k reserved,
> 1267k data, 212k init)
> Calibrating delay using timer specific routine.. 4003.11 BogoMIPS
> (lpj=2001559)
> Mount-cache hash table entries: 256
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> mtrr: v2.0 (20020519)
> Using local APIC timer interrupts.
> Detected 12.500 MHz APIC timer.
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3999.60 BogoMIPS
> (lpj=1999803)
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> CPU 1: Syncing TSC to CPU 0.
> CPU 1: synchronized TSC with CPU 0 (last diff 3 cycles, maxerr 534 cycles)
> Brought up 2 CPUs
> Disabling vsyscall due to use of PM timer
> time.c: Using PM based timekeeping.
> testing NMI watchdog ... OK.
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: Using configuration type 1
> ACPI: Subsystem revision 20050902
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> PCI quirk: region 0800-083f claimed by ali7101 ACPI
> Boot video device is 0000:03:00.0
> PCI: Transparent bridge - 0000:00:06.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HTT_._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEB1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEB2._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
> ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 13 devices
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
> report agpgart: Detected AGP bridge 20
> Setting up ULi AGP.
> agpgart: AGP aperture is 256M @ 0xd0000000
> PCI-DMA: Reserving 128MB of IOMMU area in the AGP aperture
> pnp: 00:0b: ioport range 0x290-0x29f has been reserved
> PCI: Bridge: 0000:00:01.0
> IO window: disabled.
> MEM window: fc700000-fc7fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:02.0
> IO window: disabled.
> MEM window: fc800000-fc8fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:05.0
> IO window: disabled.
> MEM window: fc900000-fe9fffff
> PREFETCH window: aff00000-bfefffff
> PCI: Bridge: 0000:00:06.0
> IO window: disabled.
> MEM window: fea00000-feafffff
> PREFETCH window: disabled.
> GSI 16 sharing vector 0xA9 and IRQ 16
> ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 29 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> GSI 17 sharing vector 0xB1 and IRQ 17
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 34 (level, low) -> IRQ 177
> PCI: Setting latency timer of device 0000:00:02.0 to 64
> PCI: Setting latency timer of device 0000:00:05.0 to 64
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> IA-32 Microcode Update Driver: v1.14 <[email protected]>
> IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
> Installing knfsd (copyright (C) 1996 [email protected]).
> NTFS driver 2.1.25 [Flags: R/W].
> fuse init (API version 7.3)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 29 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[pcie00]
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 34 (level, low) -> IRQ 177
> PCI: Setting latency timer of device 0000:00:02.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[pcie00]
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
> Using specific hotkey driver
> lp: driver loaded but no devices found
> Real Time Clock Driver v1.12
> Non-volatile memory driver v1.2
> Linux agpgart interface v0.101 (c) Dave Jones
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> parport: PnPBIOS parport detected.
> parport0: PC-style at 0x378 (0x778), irq 7, dma 3
> [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
> lp0: using parport0 (interrupt-driven).
> lp0: console ready
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ALI15X3: IDE controller at PCI slot 0000:00:12.0
> GSI 18 sharing vector 0xD1 and IRQ 18
> ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 19 (level, low) -> IRQ 209
> ALI15X3: chipset revision 199
> ALI15X3: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:pio, hdd:pio
> Probing IDE interface ide0...
> hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> ide-floppy driver 0.99.newide
> libata version 1.20 loaded.
> sata_uli 0000:00:12.1: version 0.5
> ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 19 (level, low) -> IRQ 209
> ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE082 bmdma 0xD880 irq 209
> ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD888 irq 209
> ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663
> 88:007f
> ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
> ata1: dev 0 configured for UDMA/133
> scsi0 : sata_uli
> ata2: no device found (phy stat 00000000)
> scsi1 : sata_uli
> Vendor: ATA Model: Maxtor 7L250S0 Rev: BANC
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 < sda5 sda6 sda7 >
> sd 0:0:0:0: Attached scsi disk sda
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> usbmon: debugfs is not available
> GSI 19 sharing vector 0xD9 and IRQ 19
> ACPI: PCI Interrupt 0000:00:13.3[D] -> GSI 23 (level, low) -> IRQ 217
> ehci_hcd 0000:00:13.3: EHCI Host Controller
> ehci_hcd 0000:00:13.3: debug port 1
> ehci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:13.3: irq 217, io mem 0xfebfe800
> ehci_hcd 0000:00:13.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> GSI 20 sharing vector 0xE1 and IRQ 20
> ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 20 (level, low) -> IRQ 225
> ohci_hcd 0000:00:13.0: OHCI Host Controller
> ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:13.0: irq 225, io mem 0xfebfd000
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> GSI 21 sharing vector 0xE9 and IRQ 21
> ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 21 (level, low) -> IRQ 233
> ohci_hcd 0000:00:13.1: OHCI Host Controller
> ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
> ohci_hcd 0000:00:13.1: irq 233, io mem 0xfebfc000
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 3 ports detected
> GSI 22 sharing vector 0x32 and IRQ 22
> ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 22 (level, low) -> IRQ 50
> ohci_hcd 0000:00:13.2: OHCI Host Controller
> ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
> ohci_hcd 0000:00:13.2: irq 50, io mem 0xfebfb000
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 3 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> mice: PS/2 mouse device common for all mice
> I2O subsystem v1.288
> i2o: max drivers = 8
> I2O Configuration OSM v1.248
> I2O Bus Adapter OSM v$Rev$
> I2O Block Device OSM v1.287
> I2O SCSI Peripheral OSM v1.282
> I2O ProcFS OSM v1.145
> i2c /dev entries driver
> ali1563: SMBus control = 0403
> ali1563_probe: Returning 0
> input: AT Translated Set 2 keyboard as /class/input/input0
> Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07
> 13:30:21 2005 UTC).
> GSI 23 sharing vector 0x3A and IRQ 23
> ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 58
> input: ImPS/2 Generic Wheel Mouse as /class/input/input1
> AC'97 1 does not respond - RESET
> AC'97 1 access is not valid [0xffffffff], removing mixer.
> Unable to initialize codec #1
> intel8x0_measure_ac97_clock: measured 50953 usecs
> intel8x0: clocking to 48000
> ALSA device list:
> #0: ALi M5455 with ALC850 at 0x0, irq 58
> NET: Registered protocol family 2
> IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
> powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
> powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
> powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0xa (1300 mV)
> cpu_init done, current fid 0xc, vid 0x8
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 212k freed
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda5, internal journal
> uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
> GSI 24 sharing vector 0x42 and IRQ 24
> ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 17 (level, low) -> IRQ 66
> eth0: ULi M5263 at pci0000:00:11.0, 00:13:8f:5d:2e:ea, irq 66.
> ReiserFS: sda6: found reiserfs format "3.6" with standard journal
> ReiserFS: sda6: using ordered data mode
> ReiserFS: sda6: journal params: device sda6, size 8192, journal first block
> 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> ReiserFS: sda6: checking transaction log (sda6)
> ReiserFS: sda6: Using r5 hash to sort names
> uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
> NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
> NFSD: starting 90-second grace period
> mtrr: type mismatch for b0000000,2000000 old: write-back new:
> write-combining
>
>
> 00:00.0 Host bridge: ALi Corporation M1695 K8 Northbridge [PCI Express and
> HyperTransport]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [40] HyperTransport: Slave or Primary Interface
> Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir- DUL-
> Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut-
> LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
> Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut-
> LWI=8bit DwFcInEn- LWO=16bit DwFcOutEn-
> Revision ID: 1.05
> Link Frequency 0: 800MHz
> Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+
> 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
> Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
> UIDRD-
> Link Frequency 1: 200MHz
> Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 1: 200MHz+ 300MHz- 400MHz+
> 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
> Error Handling: PFlE+ OFlE+ PFE+ OFE+ EOCFE+ RFE+ CRCFE+
> SERRFE- CF- RE- PNFE+ ONFE+ EOCNFE+ RNFE- CRCNFE+ SERRNFE-
> Prefetchable memory behind bridge Upper: 00-00
> Bus Number: 00
> Capabilities: [5c] HyperTransport: MSI Mapping
> Capabilities: [68] HyperTransport: UnitID Clumping
> Capabilities: [74] HyperTransport: Interrupt Discovery and
> Configuration
> Capabilities: [7c] Message Signalled Interrupts: 64bit+ Queue=0/1
> Enable-
> Address: 00000000fee00000 Data: 0000
> 00: b9 10 95 16 07 00 10 00 00 00 00 06 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
> 40: 08 5c 60 00 20 00 11 11 20 00 11 10 25 05 f5 00
> 50: 02 00 f5 00 ff ff 7f 5c 00 00 00 00 08 68 00 a8
> 60: 00 00 e0 fe 00 00 00 00 08 74 00 90 00 00 00 00
> 70: 00 00 00 00 08 7c 00 80 67 03 b1 f8 05 00 82 00
> 80: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:01.0 PCI bridge: ALi Corporation PCI Express Root Port (prog-if 00
> [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fc700000-fc7fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1
> Enable+
> Address: 00000000fee00000 Data: 40c1
> Capabilities: [58] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
> ExtTag+ Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port
> 0 Link: Latency L0s <2us, L1 <32us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x16
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
> Surpise- Slot: Number 0, PowerLimit 0.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Off, PwrInd Off, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [7c] HyperTransport: MSI Mapping
> Capabilities: [88] HyperTransport: Revision ID: 1.05
> 00: b9 10 4b 52 06 05 10 00 00 00 04 06 10 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
> 20: 70 fc 70 fc f0 ff 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 03 00
> 40: 01 48 02 c8 00 00 00 00 05 58 83 00 00 00 e0 fe
> 50: 00 00 00 00 c1 40 00 00 10 7c 41 01 20 00 00 00
> 60: 10 28 18 00 01 dd 02 00 00 00 10 10 00 00 00 00
> 70: c0 03 00 00 00 00 00 00 00 00 00 00 08 88 00 a8
> 80: 00 00 e0 fe 00 00 00 00 08 00 25 88 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 03 00 00 00 00 00 0c 02 08 3f 63 ed 70 2c
> b0: 00 00 00 00 00 11 00 00 00 00 00 00 01 00 3f 1f
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 01 d0 0c 40 01 04 73 00 00 00 00 00 d1 00 77 30
> e0: 00 00 00 00 01 00 00 00 01 00 00 00 26 38 18 d0
> f0: 01 50 94 2d 59 41 50 86 06 38 ef 53 40 0e 66 c1
>
> 00:02.0 PCI bridge: ALi Corporation PCI Express Root Port (prog-if 00
> [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fc800000-fc8fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1
> Enable+
> Address: 00000000fee00000 Data: 40c9
> Capabilities: [58] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
> ExtTag+ Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s L1, Port
> 0 Link: Latency L0s <2us, L1 <32us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x2
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
> Surpise- Slot: Number 0, PowerLimit 0.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Off, PwrInd Off, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [7c] HyperTransport: MSI Mapping
> Capabilities: [88] HyperTransport: Revision ID: 1.05
> 00: b9 10 4c 52 06 05 10 00 00 00 04 06 10 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 02 02 00 f0 00 00 00
> 20: 80 fc 80 fc f0 ff 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 03 00
> 40: 01 48 02 c8 00 00 00 00 05 58 83 00 00 00 e0 fe
> 50: 00 00 00 00 c9 40 00 00 10 7c 41 01 20 00 00 00
> 60: 10 28 18 00 21 dc 02 00 00 00 10 10 00 00 00 00
> 70: c0 03 00 00 00 00 00 00 00 00 00 00 08 88 00 a8
> 80: 00 00 e0 fe 00 00 00 00 08 00 25 88 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 03 00 00 00 00 00 0c 02 09 3f 63 ed 70 2c
> b0: 00 00 00 00 00 11 00 00 04 00 00 00 01 00 3f 1f
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 01 d0 0c 40 01 04 73 00 00 00 00 00 d1 00 77 30
> e0: 00 00 00 00 01 00 00 00 01 00 00 00 64 b1 41 40
> f0: d7 2e 91 66 7e 1d fc 1a cc 24 dc 44 22 2d 40 a4
>
> 00:04.0 Host bridge: ALi Corporation M1689 K8 Northbridge [Super K8 Single
> Chip]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
> Capabilities: [40] HyperTransport: Slave or Primary Interface
> Command: BaseUnitID=4 UnitCnt=1 MastHost- DefDir- DUL-
> Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 0: MLWI=16bit DwFcIn- MLWO=8bit DwFcOut-
> LWI=16bit DwFcInEn- LWO=8bit DwFcOutEn-
> Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut-
> LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
> Revision ID: 1.04
> Link Frequency 0: 800MHz
> Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+
> 500MHz- 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
> Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
> UIDRD-
> Link Frequency 1: 200MHz
> Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 1: 200MHz- 300MHz- 400MHz-
> 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
> Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
> SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
> Prefetchable memory behind bridge Upper: 00-00
> Bus Number: 00
> Capabilities: [60] HyperTransport: Interrupt Discovery and
> Configuration
> Capabilities: [80] AGP version 3.0
> Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
> HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
> Rate=<none>
> 00: b9 10 89 16 06 01 10 00 00 00 00 06 00 00 00 00
> 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
> 40: 08 60 24 00 20 00 01 01 d0 00 00 00 24 05 35 00
> 50: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 08 80 32 80 66 03 42 f8 00 00 00 00 00 05 17 50
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 02 00 30 00 07 02 00 1b 00 00 00 00 0a 00 20 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:05.0 PCI bridge: ALi Corporation AGP8X Controller (prog-if 00 [Normal
> decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fc900000-fe9fffff
> Prefetchable memory behind bridge: aff00000-bfefffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
> 00: b9 10 46 52 07 01 20 00 00 00 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 03 03 40 f0 00 20 22
> 20: 90 fc 90 fe f0 af e0 bf 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0b 00
> 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 20 78 00 c0 00 20 20 20 20 20 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 11 00 00 00 00 11 00 01 20 1a
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:06.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge (prog-if 01
> [Subtractive decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fea00000-feafffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> 00: b9 10 49 52 06 01 00 00 00 01 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 04 04 20 f0 00 00 22
> 20: a0 fe a0 fe f0 ff 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00
> 40: 00 80 00 78 00 00 00 00 80 00 00 20 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.0 ISA bridge: ALi Corporation M1563 HyperTransport South Bridge (rev
> 70) Subsystem: ASRock Incorporation Unknown device 1563
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (250ns min, 6000ns max)
> 00: b9 10 63 15 0f 00 00 02 70 00 01 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 63 15
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 18
> 40: f7 e4 00 09 3d fa 00 00 00 00 00 00 03 c0 00 10
> 50: 02 00 02 00 0d 09 01 80 ff 3c fb 67 a1 60 10 00
> 60: d8 f8 c0 f2 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 07 63 15 00 0f 00 00 00 00 00 20 00 00 00 00
> 80: 03 04 00 00 21 0f cc dd ee 99 aa 99 00 bb 00 5f
> 90: 80 03 83 00 00 00 00 00 1e 00 00 00 00 00 e0 fe
> a0: 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: df 80 01 00 c0 00 f0 08 5f 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
> Subsystem: ASRock Incorporation Unknown device 7101
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: b9 10 01 71 00 00 00 02 00 00 80 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 01 71
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 40 00 00 00 00 20 00 08 7a 00 00 00 00 00 00
> 50: 00 07 ff 58 00 00 00 00 00 df 0f 10 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 ff 3f 3f 3f
> 70: ff 07 00 00 00 00 00 08 76 88 b0 08 3c fe ff 00
> 80: 32 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 a0 aa 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: ff 44 80 20 00 ff ff 07 00 00 28 70 40 9b 02 00
> c0: 12 00 10 10 00 00 00 00 00 00 ff 00 4b 00 00 00
> d0: 00 42 04 00 40 00 22 04 4c 2f 00 00 00 00 00 00
> e0: 00 08 00 00 0e 29 cb 55 b4 00 01 00 00 00 00 36
> f0: 00 00 00 00 00 00 00 f0 00 00 00 00 00 00 00 00
>
> 00:08.0 Multimedia audio controller: ALi Corporation M5455 PCI AC-Link
> Controller Audio Device (rev 20)
> Subsystem: ASRock Incorporation Unknown device 0850
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (16000ns min), Cache Line Size 10
> Interrupt: pin A routed to IRQ 58
> Region 0: I/O ports at e800 [size=256]
> Region 1: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: b9 10 55 54 17 00 10 02 20 00 01 04 10 20 00 00
> 10: 01 e8 00 00 00 f0 bf fe 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 50 08
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 40 00
> 40: 01 00 22 e6 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 49 18 50 08 10 00 c4 00 40 00 07 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 57 54 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:11.0 Ethernet controller: ALi Corporation M5263 Ethernet Controller (rev
> 40)
> Subsystem: ASRock Incorporation Unknown device 5263
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (5000ns min, 10000ns max), Cache Line Size 08
> Interrupt: pin A routed to IRQ 66
> Region 0: I/O ports at e400 [size=256]
> Region 1: Memory at febfec00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: b9 10 63 52 07 01 10 02 40 00 00 02 08 20 00 00
> 10: 01 e4 00 00 00 ec bf fe 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 63 52
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 14 28
> 40: 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 01 00 22 c0 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:12.0 IDE interface: ALi Corporation M5229 IDE (rev c7) (prog-if 8a
> [Master SecP PriP])
> Subsystem: ASRock Incorporation Unknown device 5229
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 209
> Region 0: I/O ports at <ignored>
> Region 1: I/O ports at <ignored>
> Region 2: I/O ports at <ignored>
> Region 3: I/O ports at <ignored>
> Region 4: I/O ports at ff00 [size=16]
> 00: b9 10 29 52 05 00 a0 02 c7 8a 01 01 00 20 80 00
> 10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
> 20: 01 ff 00 00 00 00 00 00 00 00 00 00 49 18 29 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
> 40: 00 00 00 7a 4d 10 00 c0 00 80 64 c9 00 00 ba 1a
> 50: 00 00 00 01 50 55 4a 44 01 31 31 00 00 00 00 00
> 60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 01 00 01 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:12.1 IDE interface: ALi Corporation ULi 5289 SATA (rev 10) (prog-if 8f
> [Master SecP SecO PriP PriO])
> Subsystem: ASRock Incorporation Unknown device 5289
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size 10
> Interrupt: pin A routed to IRQ 209
> Region 0: I/O ports at ec00 [size=8]
> Region 1: I/O ports at e080 [size=4]
> Region 2: I/O ports at e000 [size=8]
> Region 3: I/O ports at dc00 [size=4]
> Region 4: I/O ports at d880 [size=16]
> 00: b9 10 89 52 05 01 a0 02 10 8f 01 01 10 20 80 00
> 10: 01 ec 00 00 81 e0 00 00 01 e0 00 00 01 dc 00 00
> 20: 81 d8 00 00 00 00 00 00 00 00 00 00 49 18 89 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 06 01 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 1f 00 00 03 10 01 00 00 00 68 00 68 00
> 90: 13 01 00 00 01 04 8d 04 00 03 00 00 00 00 00 00
> a0: 00 00 00 00 00 04 80 00 00 03 00 00 00 00 00 00
> b0: 00 00 00 00 88 b1 0e 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> (prog-if 10 [OHCI])
> Subsystem: ASRock Incorporation Unknown device 5237
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size 10
> Interrupt: pin A routed to IRQ 225
> Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
> 00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
> 10: 00 d0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 50
> 40: 00 00 1f 00 e0 40 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> (prog-if 10 [OHCI])
> Subsystem: ASRock Incorporation Unknown device 5237
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size 10
> Interrupt: pin B routed to IRQ 233
> Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
> 00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
> 10: 00 c0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 50
> 40: 00 00 1f 00 e0 48 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> (prog-if 10 [OHCI])
> Subsystem: ASRock Incorporation Unknown device 5237
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size 10
> Interrupt: pin C routed to IRQ 50
> Region 0: Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
> 00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
> 10: 00 b0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 50
> 40: 00 00 1f 00 e0 48 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
> (prog-if 20 [EHCI])
> Subsystem: ASRock Incorporation Unknown device 5239
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (4000ns min, 8000ns max), Cache Line Size 10
> Interrupt: pin D routed to IRQ 217
> Region 0: Memory at febfe800 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Debug port
> 00: b9 10 39 52 16 01 b0 02 01 20 03 0c 10 20 80 00
> 10: 00 e8 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 39 52
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 10 20
> 40: 20 03 00 c4 80 02 10 c4 00 00 00 00 00 00 00 00
> 50: 01 58 02 c8 00 00 00 00 0a 00 90 20 00 00 00 00
> 60: 20 20 7f 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 00 01 00 00 08 c0 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> HyperTransport Technology Configuration
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Capabilities: [80] HyperTransport: Host or Secondary Interface
> !!! Possibly incomplete decoding
> Command: WarmRst+ DblEnd-
> Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0
> Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
> Revision ID: 1.02
> 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
> 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
> 60: 00 00 01 00 e4 00 00 00 20 c8 00 0f 1c 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 08 00 01 21 20 00 11 11 22 05 75 80 02 00 00 00
> 90: 56 04 51 02 00 00 ff 00 07 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Address Map
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 03 00 00 00 00 00 7f 01 00 00 00 00 01 00 00 00
> 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
> 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
> 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
> 80: 03 00 e0 00 00 ff ef 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 03 0a 00 00 00 0b 00 00 03 00 80 00 00 ff ff 00
> c0: 13 10 00 00 00 f0 ff 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 03 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> DRAM Controller
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 00 00 00 01 00 00 04 01 00 00 10 01 00 00 14
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 fe e0 03 00 fe e0 03 00 fe e0 03 00 fe e0 03
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 77 00 00 00 00 00 00 00 45 34 82 13 31 0b 00 00
> 90: 80 8e 05 38 07 07 7b 3e 00 00 00 00 0d 02 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 71 9f 5e 3b 71 00 00 00 ff 31 00 00 bd ae fb ff
> c0: 00 80 03 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 15 4c f1 f0 24 80 c8 20 4d eb fe f4 10 90 00 1a
> e0: 45 1c 34 00 11 18 40 40 d3 55 bf b7 1f 6d 3c fd
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Miscellaneous Control
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: ff 3b 00 00 40 00 00 08 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 80 90 45 01
> 60: 8c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 11 01 02 51 11 80 00 50 00 38 00 08 1a 22 00 00
> 80: 00 00 07 23 13 21 13 21 00 00 00 00 00 00 00 00
> 90: 07 00 00 00 68 00 00 00 00 80 7f 01 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 37 00 00 00 00 80 4d 5c
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 01 a7 0d 00 10 27 60 20 00 00 00 00
> e0: 00 00 00 00 20 07 4e 0e 19 11 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 03:00.0 VGA compatible controller: nVidia Corporation NV15 [GeForce2
> GTS/Pro] (rev a3) (prog-if 00 [VGA])
> Subsystem: Elsa AG Gladiac
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at b0000000 (32-bit, prefetchable) [size=128M]
> Expansion ROM at fe9f0000 [disabled] [size=64K]
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
> HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
> Rate=<none>
> 00: de 10 50 01 07 00 b0 02 a3 00 00 03 00 20 00 00
> 10: 00 00 00 fd 08 00 00 b0 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 48 10 50 0c
> 30: 00 00 9f fe 60 00 00 00 00 00 00 00 05 01 05 01
> 40: 48 10 50 0c 02 00 20 00 17 00 00 1f 00 00 00 00
> 50: 01 00 00 00 01 00 00 00 ce d6 23 00 0f 00 00 00
> 60: 01 44 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> #
> # Automatically generated make config: don't edit
> # Linux kernel version: 2.6.15
> # Thu Jan 12 14:47:37 2006
> #
> CONFIG_X86_64=y
> CONFIG_64BIT=y
> CONFIG_X86=y
> CONFIG_SEMAPHORE_SLEEPERS=y
> CONFIG_MMU=y
> CONFIG_RWSEM_GENERIC_SPINLOCK=y
> CONFIG_GENERIC_CALIBRATE_DELAY=y
> CONFIG_X86_CMPXCHG=y
> CONFIG_EARLY_PRINTK=y
> CONFIG_GENERIC_ISA_DMA=y
> CONFIG_GENERIC_IOMAP=y
> CONFIG_ARCH_MAY_HAVE_PC_FDC=y
>
> #
> # Code maturity level options
> #
> CONFIG_EXPERIMENTAL=y
> # CONFIG_CLEAN_COMPILE is not set
> CONFIG_BROKEN=y
> CONFIG_BROKEN_ON_SMP=y
> CONFIG_LOCK_KERNEL=y
> CONFIG_INIT_ENV_ARG_LIMIT=32
>
> #
> # General setup
> #
> CONFIG_LOCALVERSION=""
> CONFIG_LOCALVERSION_AUTO=y
> CONFIG_SWAP=y
> CONFIG_SYSVIPC=y
> CONFIG_POSIX_MQUEUE=y
> # CONFIG_BSD_PROCESS_ACCT is not set
> CONFIG_SYSCTL=y
> # CONFIG_AUDIT is not set
> CONFIG_HOTPLUG=y
> CONFIG_KOBJECT_UEVENT=y
> CONFIG_IKCONFIG=y
> CONFIG_IKCONFIG_PROC=y
> # CONFIG_CPUSETS is not set
> CONFIG_INITRAMFS_SOURCE=""
> CONFIG_CC_OPTIMIZE_FOR_SIZE=y
> # CONFIG_EMBEDDED is not set
> CONFIG_KALLSYMS=y
> # CONFIG_KALLSYMS_ALL is not set
> # CONFIG_KALLSYMS_EXTRA_PASS is not set
> CONFIG_PRINTK=y
> CONFIG_BUG=y
> CONFIG_BASE_FULL=y
> CONFIG_FUTEX=y
> CONFIG_EPOLL=y
> CONFIG_SHMEM=y
> CONFIG_CC_ALIGN_FUNCTIONS=0
> CONFIG_CC_ALIGN_LABELS=0
> CONFIG_CC_ALIGN_LOOPS=0
> CONFIG_CC_ALIGN_JUMPS=0
> # CONFIG_TINY_SHMEM is not set
> CONFIG_BASE_SMALL=0
>
> #
> # Loadable module support
> #
> CONFIG_MODULES=y
> CONFIG_MODULE_UNLOAD=y
> # CONFIG_MODULE_FORCE_UNLOAD is not set
> CONFIG_OBSOLETE_MODPARM=y
> # CONFIG_MODVERSIONS is not set
> # CONFIG_MODULE_SRCVERSION_ALL is not set
> CONFIG_KMOD=y
> CONFIG_STOP_MACHINE=y
>
> #
> # Block layer
> #
> CONFIG_LBD=y
>
> #
> # IO Schedulers
> #
> CONFIG_IOSCHED_NOOP=y
> CONFIG_IOSCHED_AS=y
> CONFIG_IOSCHED_DEADLINE=y
> CONFIG_IOSCHED_CFQ=y
> # CONFIG_DEFAULT_AS is not set
> # CONFIG_DEFAULT_DEADLINE is not set
> CONFIG_DEFAULT_CFQ=y
> # CONFIG_DEFAULT_NOOP is not set
> CONFIG_DEFAULT_IOSCHED="cfq"
>
> #
> # Processor type and features
> #
> CONFIG_MK8=y
> # CONFIG_MPSC is not set
> # CONFIG_GENERIC_CPU is not set
> CONFIG_X86_L1_CACHE_BYTES=64
> CONFIG_X86_L1_CACHE_SHIFT=6
> CONFIG_X86_TSC=y
> CONFIG_X86_GOOD_APIC=y
> CONFIG_MICROCODE=y
> CONFIG_X86_MSR=y
> CONFIG_X86_CPUID=y
> CONFIG_X86_IO_APIC=y
> CONFIG_X86_LOCAL_APIC=y
> CONFIG_MTRR=y
> CONFIG_SMP=y
> # CONFIG_SCHED_SMT is not set
> # CONFIG_PREEMPT_NONE is not set
> # CONFIG_PREEMPT_VOLUNTARY is not set
> CONFIG_PREEMPT=y
> CONFIG_PREEMPT_BKL=y
> # CONFIG_NUMA is not set
> CONFIG_ARCH_FLATMEM_ENABLE=y
> CONFIG_SELECT_MEMORY_MODEL=y
> CONFIG_FLATMEM_MANUAL=y
> # CONFIG_DISCONTIGMEM_MANUAL is not set
> # CONFIG_SPARSEMEM_MANUAL is not set
> CONFIG_FLATMEM=y
> CONFIG_FLAT_NODE_MEM_MAP=y
> # CONFIG_SPARSEMEM_STATIC is not set
> CONFIG_SPLIT_PTLOCK_CPUS=4
> CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y
> CONFIG_NR_CPUS=2
> # CONFIG_HOTPLUG_CPU is not set
> CONFIG_HPET_TIMER=y
> CONFIG_X86_PM_TIMER=y
> CONFIG_HPET_EMULATE_RTC=y
> CONFIG_GART_IOMMU=y
> CONFIG_SWIOTLB=y
> CONFIG_X86_MCE=y
> CONFIG_X86_MCE_INTEL=y
> CONFIG_X86_MCE_AMD=y
> CONFIG_PHYSICAL_START=0x100000
> CONFIG_KEXEC=y
> CONFIG_SECCOMP=y
> # CONFIG_HZ_100 is not set
> # CONFIG_HZ_250 is not set
> CONFIG_HZ_1000=y
> CONFIG_HZ=1000
> CONFIG_GENERIC_HARDIRQS=y
> CONFIG_GENERIC_IRQ_PROBE=y
> CONFIG_ISA_DMA_API=y
> CONFIG_GENERIC_PENDING_IRQ=y
>
> #
> # Power management options
> #
> CONFIG_PM=y
> CONFIG_PM_LEGACY=y
> # CONFIG_PM_DEBUG is not set
>
> #
> # ACPI (Advanced Configuration and Power Interface) Support
> #
> CONFIG_ACPI=y
> CONFIG_ACPI_AC=y
> CONFIG_ACPI_BATTERY=y
> CONFIG_ACPI_BUTTON=y
> CONFIG_ACPI_VIDEO=y
> CONFIG_ACPI_HOTKEY=y
> CONFIG_ACPI_FAN=y
> CONFIG_ACPI_PROCESSOR=y
> CONFIG_ACPI_THERMAL=y
> # CONFIG_ACPI_ASUS is not set
> # CONFIG_ACPI_IBM is not set
> # CONFIG_ACPI_TOSHIBA is not set
> # CONFIG_ACPI_CUSTOM_DSDT is not set
> CONFIG_ACPI_BLACKLIST_YEAR=0
> # CONFIG_ACPI_DEBUG is not set
> CONFIG_ACPI_EC=y
> CONFIG_ACPI_POWER=y
> CONFIG_ACPI_SYSTEM=y
> CONFIG_ACPI_CONTAINER=y
>
> #
> # CPU Frequency scaling
> #
> CONFIG_CPU_FREQ=y
> CONFIG_CPU_FREQ_TABLE=y
> # CONFIG_CPU_FREQ_DEBUG is not set
> CONFIG_CPU_FREQ_STAT=y
> # CONFIG_CPU_FREQ_STAT_DETAILS is not set
> CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
> # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
> CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
> CONFIG_CPU_FREQ_GOV_POWERSAVE=y
> CONFIG_CPU_FREQ_GOV_USERSPACE=y
> CONFIG_CPU_FREQ_GOV_ONDEMAND=y
> CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
>
> #
> # CPUFreq processor drivers
> #
> CONFIG_X86_POWERNOW_K8=y
> CONFIG_X86_POWERNOW_K8_ACPI=y
> # CONFIG_X86_SPEEDSTEP_CENTRINO is not set
> CONFIG_X86_ACPI_CPUFREQ=y
>
> #
> # shared options
> #
> # CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
> # CONFIG_X86_SPEEDSTEP_LIB is not set
>
> #
> # Bus options (PCI etc.)
> #
> CONFIG_PCI=y
> CONFIG_PCI_DIRECT=y
> CONFIG_PCI_MMCONFIG=y
> CONFIG_UNORDERED_IO=y
> CONFIG_PCIEPORTBUS=y
> CONFIG_PCI_MSI=y
> CONFIG_PCI_LEGACY_PROC=y
> # CONFIG_PCI_DEBUG is not set
>
> #
> # PCCARD (PCMCIA/CardBus) support
> #
> # CONFIG_PCCARD is not set
>
> #
> # PCI Hotplug Support
> #
> # CONFIG_HOTPLUG_PCI is not set
>
> #
> # Executable file formats / Emulations
> #
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=y
> CONFIG_IA32_EMULATION=y
> # CONFIG_IA32_AOUT is not set
> CONFIG_COMPAT=y
> CONFIG_SYSVIPC_COMPAT=y
> CONFIG_UID16=y
>
> #
> # Networking
> #
> CONFIG_NET=y
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> # CONFIG_PACKET_MMAP is not set
> CONFIG_UNIX=y
> # CONFIG_NET_KEY is not set
> CONFIG_INET=y
> CONFIG_IP_MULTICAST=y
> # CONFIG_IP_ADVANCED_ROUTER is not set
> CONFIG_IP_FIB_HASH=y
> # CONFIG_IP_PNP is not set
> # CONFIG_NET_IPIP is not set
> # CONFIG_NET_IPGRE is not set
> # CONFIG_IP_MROUTE is not set
> # CONFIG_ARPD is not set
> # CONFIG_SYN_COOKIES is not set
> # CONFIG_INET_AH is not set
> # CONFIG_INET_ESP is not set
> # CONFIG_INET_IPCOMP is not set
> # CONFIG_INET_TUNNEL is not set
> CONFIG_INET_DIAG=y
> CONFIG_INET_TCP_DIAG=y
> # CONFIG_TCP_CONG_ADVANCED is not set
> CONFIG_TCP_CONG_BIC=y
> # CONFIG_IPV6 is not set
> # CONFIG_NETFILTER is not set
>
> #
> # DCCP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_DCCP is not set
>
> #
> # SCTP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_SCTP is not set
> # CONFIG_ATM is not set
> # CONFIG_BRIDGE is not set
> # CONFIG_VLAN_8021Q is not set
> # CONFIG_DECNET is not set
> # CONFIG_LLC2 is not set
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
> # CONFIG_X25 is not set
> # CONFIG_LAPB is not set
> # CONFIG_NET_DIVERT is not set
> # CONFIG_ECONET is not set
> # CONFIG_WAN_ROUTER is not set
>
> #
> # QoS and/or fair queueing
> #
> # CONFIG_NET_SCHED is not set
>
> #
> # Network testing
> #
> # CONFIG_NET_PKTGEN is not set
> # CONFIG_HAMRADIO is not set
> # CONFIG_IRDA is not set
> # CONFIG_BT is not set
> # CONFIG_IEEE80211 is not set
>
> #
> # Device Drivers
> #
>
> #
> # Generic Driver Options
> #
> # CONFIG_STANDALONE is not set
> CONFIG_PREVENT_FIRMWARE_BUILD=y
> # CONFIG_FW_LOADER is not set
> # CONFIG_DEBUG_DRIVER is not set
>
> #
> # Connector - unified userspace <-> kernelspace linker
> #
> # CONFIG_CONNECTOR is not set
>
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
>
> #
> # Parallel port support
> #
> CONFIG_PARPORT=y
> CONFIG_PARPORT_PC=y
> # CONFIG_PARPORT_SERIAL is not set
> CONFIG_PARPORT_PC_FIFO=y
> CONFIG_PARPORT_PC_SUPERIO=y
> # CONFIG_PARPORT_GSC is not set
> CONFIG_PARPORT_1284=y
>
> #
> # Plug and Play support
> #
> CONFIG_PNP=y
> # CONFIG_PNP_DEBUG is not set
>
> #
> # Protocols
> #
> CONFIG_PNPACPI=y
>
> #
> # Block devices
> #
> CONFIG_BLK_DEV_FD=m
> # CONFIG_PARIDE is not set
> # CONFIG_BLK_CPQ_DA is not set
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> # CONFIG_BLK_DEV_UMEM is not set
> # CONFIG_BLK_DEV_COW_COMMON is not set
> # CONFIG_BLK_DEV_LOOP is not set
> # CONFIG_BLK_DEV_NBD is not set
> # CONFIG_BLK_DEV_SX8 is not set
> # CONFIG_BLK_DEV_UB is not set
> # CONFIG_BLK_DEV_RAM is not set
> CONFIG_BLK_DEV_RAM_COUNT=16
> # CONFIG_CDROM_PKTCDVD is not set
> # CONFIG_ATA_OVER_ETH is not set
>
> #
> # ATA/ATAPI/MFM/RLL support
> #
> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_IDE_SATA is not set
> # CONFIG_BLK_DEV_HD_IDE is not set
> CONFIG_BLK_DEV_IDEDISK=y
> CONFIG_IDEDISK_MULTI_MODE=y
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> CONFIG_BLK_DEV_IDEFLOPPY=y
> # CONFIG_BLK_DEV_IDESCSI is not set
> # CONFIG_IDE_TASK_IOCTL is not set
>
> #
> # IDE chipset support/bugfixes
> #
> # CONFIG_IDE_GENERIC is not set
> # CONFIG_BLK_DEV_CMD640 is not set
> # CONFIG_BLK_DEV_IDEPNP is not set
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> # CONFIG_BLK_DEV_GENERIC is not set
> # CONFIG_BLK_DEV_OPTI621 is not set
> # CONFIG_BLK_DEV_RZ1000 is not set
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
> CONFIG_IDEDMA_PCI_AUTO=y
> # CONFIG_IDEDMA_ONLYDISK is not set
> # CONFIG_BLK_DEV_AEC62XX is not set
> CONFIG_BLK_DEV_ALI15X3=y
> # CONFIG_WDC_ALI15X3 is not set
> # CONFIG_BLK_DEV_AMD74XX is not set
> # CONFIG_BLK_DEV_ATIIXP is not set
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_TRIFLEX is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5520 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> # CONFIG_BLK_DEV_SC1200 is not set
> # CONFIG_BLK_DEV_PIIX is not set
> # CONFIG_BLK_DEV_IT821X is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_PDC202XX_OLD is not set
> # CONFIG_BLK_DEV_PDC202XX_NEW is not set
> # CONFIG_BLK_DEV_SVWKS is not set
> # CONFIG_BLK_DEV_SIIMAGE is not set
> # CONFIG_BLK_DEV_SIS5513 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_VIA82CXXX is not set
> # CONFIG_IDE_ARM is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_IDEDMA_IVB is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_BLK_DEV_HD is not set
>
> #
> # SCSI device support
> #
> # CONFIG_RAID_ATTRS is not set
> CONFIG_SCSI=y
> CONFIG_SCSI_PROC_FS=y
>
> #
> # SCSI support type (disk, tape, CD-ROM)
> #
> CONFIG_BLK_DEV_SD=y
> # CONFIG_CHR_DEV_ST is not set
> # CONFIG_CHR_DEV_OSST is not set
> # CONFIG_BLK_DEV_SR is not set
> CONFIG_CHR_DEV_SG=y
> # CONFIG_CHR_DEV_SCH is not set
>
> #
> # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
> #
> # CONFIG_SCSI_MULTI_LUN is not set
> # CONFIG_SCSI_CONSTANTS is not set
> # CONFIG_SCSI_LOGGING is not set
>
> #
> # SCSI Transport Attributes
> #
> # CONFIG_SCSI_SPI_ATTRS is not set
> # CONFIG_SCSI_FC_ATTRS is not set
> # CONFIG_SCSI_ISCSI_ATTRS is not set
> # CONFIG_SCSI_SAS_ATTRS is not set
>
> #
> # SCSI low-level drivers
> #
> # CONFIG_ISCSI_TCP is not set
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_3W_9XXX is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AACRAID is not set
> # CONFIG_SCSI_AIC7XXX is not set
> # CONFIG_SCSI_AIC7XXX_OLD is not set
> # CONFIG_SCSI_AIC79XX is not set
> # CONFIG_SCSI_ADVANSYS is not set
> # CONFIG_MEGARAID_NEWGEN is not set
> # CONFIG_MEGARAID_LEGACY is not set
> # CONFIG_MEGARAID_SAS is not set
> CONFIG_SCSI_SATA=y
> CONFIG_SCSI_SATA_AHCI=y
> # CONFIG_SCSI_SATA_SVW is not set
> # CONFIG_SCSI_ATA_PIIX is not set
> # CONFIG_SCSI_SATA_MV is not set
> # CONFIG_SCSI_SATA_NV is not set
> # CONFIG_SCSI_PDC_ADMA is not set
> # CONFIG_SCSI_SATA_QSTOR is not set
> # CONFIG_SCSI_SATA_PROMISE is not set
> # CONFIG_SCSI_SATA_SX4 is not set
> # CONFIG_SCSI_SATA_SIL is not set
> # CONFIG_SCSI_SATA_SIL24 is not set
> # CONFIG_SCSI_SATA_SIS is not set
> CONFIG_SCSI_SATA_ULI=y
> # CONFIG_SCSI_SATA_VIA is not set
> # CONFIG_SCSI_SATA_VITESSE is not set
> CONFIG_SCSI_SATA_INTEL_COMBINED=y
> # CONFIG_SCSI_BUSLOGIC is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_EATA_PIO is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_IPS is not set
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_PPA is not set
> # CONFIG_SCSI_IMM is not set
> # CONFIG_SCSI_SYM53C8XX_2 is not set
> # CONFIG_SCSI_IPR is not set
> # CONFIG_SCSI_QLOGIC_FC is not set
> # CONFIG_SCSI_QLOGIC_1280 is not set
> CONFIG_SCSI_QLA2XXX=y
> # CONFIG_SCSI_QLA21XX is not set
> # CONFIG_SCSI_QLA22XX is not set
> # CONFIG_SCSI_QLA2300 is not set
> # CONFIG_SCSI_QLA2322 is not set
> # CONFIG_SCSI_QLA6312 is not set
> # CONFIG_SCSI_QLA24XX is not set
> # CONFIG_SCSI_LPFC is not set
> # CONFIG_SCSI_DC395x is not set
> # CONFIG_SCSI_DC390T is not set
> # CONFIG_SCSI_DEBUG is not set
>
> #
> # Multi-device support (RAID and LVM)
> #
> # CONFIG_MD is not set
>
> #
> # Fusion MPT device support
> #
> # CONFIG_FUSION is not set
> # CONFIG_FUSION_SPI is not set
> # CONFIG_FUSION_FC is not set
> # CONFIG_FUSION_SAS is not set
>
> #
> # IEEE 1394 (FireWire) support
> #
> # CONFIG_IEEE1394 is not set
>
> #
> # I2O device support
> #
> CONFIG_I2O=y
> CONFIG_I2O_EXT_ADAPTEC=y
> CONFIG_I2O_EXT_ADAPTEC_DMA64=y
> CONFIG_I2O_CONFIG=y
> CONFIG_I2O_CONFIG_OLD_IOCTL=y
> CONFIG_I2O_BUS=y
> CONFIG_I2O_BLOCK=y
> CONFIG_I2O_SCSI=y
> CONFIG_I2O_PROC=y
>
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
> CONFIG_DUMMY=y
> # CONFIG_BONDING is not set
> # CONFIG_EQUALIZER is not set
> # CONFIG_TUN is not set
> # CONFIG_NET_SB1000 is not set
>
> #
> # ARCnet devices
> #
> # CONFIG_ARCNET is not set
>
> #
> # PHY device support
> #
> # CONFIG_PHYLIB is not set
>
> #
> # Ethernet (10 or 100Mbit)
> #
> CONFIG_NET_ETHERNET=y
> CONFIG_MII=y
> # CONFIG_HAPPYMEAL is not set
> # CONFIG_SUNGEM is not set
> # CONFIG_CASSINI is not set
> # CONFIG_NET_VENDOR_3COM is not set
>
> #
> # Tulip family network device support
> #
> CONFIG_NET_TULIP=y
> # CONFIG_DE2104X is not set
> # CONFIG_TULIP is not set
> # CONFIG_DE4X5 is not set
> # CONFIG_WINBOND_840 is not set
> # CONFIG_DM9102 is not set
> CONFIG_ULI526X=m
> # CONFIG_HP100 is not set
> # CONFIG_NET_PCI is not set
> # CONFIG_NET_POCKET is not set
>
> #
> # Ethernet (1000 Mbit)
> #
> # CONFIG_ACENIC is not set
> # CONFIG_DL2K is not set
> # CONFIG_E1000 is not set
> # CONFIG_NS83820 is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_YELLOWFIN is not set
> # CONFIG_R8169 is not set
> # CONFIG_SIS190 is not set
> # CONFIG_SKGE is not set
> # CONFIG_SK98LIN is not set
> # CONFIG_TIGON3 is not set
> # CONFIG_BNX2 is not set
>
> #
> # Ethernet (10000 Mbit)
> #
> # CONFIG_CHELSIO_T1 is not set
> # CONFIG_IXGB is not set
> # CONFIG_S2IO is not set
>
> #
> # Token Ring devices
> #
> # CONFIG_TR is not set
>
> #
> # Wireless LAN (non-hamradio)
> #
> # CONFIG_NET_RADIO is not set
>
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
> # CONFIG_FDDI is not set
> # CONFIG_HIPPI is not set
> # CONFIG_PLIP is not set
> # CONFIG_PPP is not set
> # CONFIG_SLIP is not set
> # CONFIG_NET_FC is not set
> # CONFIG_SHAPER is not set
> # CONFIG_NETCONSOLE is not set
> # CONFIG_NETPOLL is not set
> # CONFIG_NET_POLL_CONTROLLER is not set
>
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
>
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
>
> #
> # Input device support
> #
> CONFIG_INPUT=y
>
> #
> # Userland interfaces
> #
> CONFIG_INPUT_MOUSEDEV=y
> CONFIG_INPUT_MOUSEDEV_PSAUX=y
> CONFIG_INPUT_MOUSEDEV_SCREEN_X=1280
> CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1024
> # CONFIG_INPUT_JOYDEV is not set
> # CONFIG_INPUT_TSDEV is not set
> CONFIG_INPUT_EVDEV=y
> # CONFIG_INPUT_EVBUG is not set
>
> #
> # Input Device Drivers
> #
> CONFIG_INPUT_KEYBOARD=y
> CONFIG_KEYBOARD_ATKBD=y
> # CONFIG_KEYBOARD_SUNKBD is not set
> # CONFIG_KEYBOARD_LKKBD is not set
> # CONFIG_KEYBOARD_XTKBD is not set
> # CONFIG_KEYBOARD_NEWTON is not set
> CONFIG_INPUT_MOUSE=y
> CONFIG_MOUSE_PS2=y
> # CONFIG_MOUSE_SERIAL is not set
> # CONFIG_MOUSE_VSXXXAA is not set
> # CONFIG_INPUT_JOYSTICK is not set
> # CONFIG_INPUT_TOUCHSCREEN is not set
> # CONFIG_INPUT_MISC is not set
>
> #
> # Hardware I/O ports
> #
> CONFIG_SERIO=y
> CONFIG_SERIO_I8042=y
> # CONFIG_SERIO_SERPORT is not set
> # CONFIG_SERIO_CT82C710 is not set
> # CONFIG_SERIO_PARKBD is not set
> # CONFIG_SERIO_PCIPS2 is not set
> CONFIG_SERIO_LIBPS2=y
> # CONFIG_SERIO_RAW is not set
> # CONFIG_GAMEPORT is not set
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_HW_CONSOLE=y
> # CONFIG_SERIAL_NONSTANDARD is not set
>
> #
> # Serial drivers
> #
> CONFIG_SERIAL_8250=y
> # CONFIG_SERIAL_8250_CONSOLE is not set
> # CONFIG_SERIAL_8250_ACPI is not set
> CONFIG_SERIAL_8250_NR_UARTS=4
> # CONFIG_SERIAL_8250_EXTENDED is not set
>
> #
> # Non-8250 serial port support
> #
> CONFIG_SERIAL_CORE=y
> # CONFIG_SERIAL_JSM is not set
> CONFIG_UNIX98_PTYS=y
> CONFIG_LEGACY_PTYS=y
> CONFIG_LEGACY_PTY_COUNT=256
> CONFIG_PRINTER=y
> CONFIG_LP_CONSOLE=y
> # CONFIG_PPDEV is not set
> # CONFIG_TIPAR is not set
>
> #
> # IPMI
> #
> # CONFIG_IPMI_HANDLER is not set
>
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> # CONFIG_HW_RANDOM is not set
> CONFIG_NVRAM=y
> CONFIG_RTC=y
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
>
> #
> # Ftape, the floppy tape device driver
> #
> # CONFIG_FTAPE is not set
> CONFIG_AGP=y
> CONFIG_AGP_AMD64=y
> # CONFIG_AGP_INTEL is not set
> # CONFIG_DRM is not set
> # CONFIG_MWAVE is not set
> # CONFIG_RAW_DRIVER is not set
> CONFIG_HPET=y
> # CONFIG_HPET_RTC_IRQ is not set
> CONFIG_HPET_MMAP=y
> # CONFIG_HANGCHECK_TIMER is not set
>
> #
> # TPM devices
> #
> # CONFIG_TCG_TPM is not set
> # CONFIG_TELCLOCK is not set
>
> #
> # I2C support
> #
> CONFIG_I2C=y
> CONFIG_I2C_CHARDEV=y
>
> #
> # I2C Algorithms
> #
> CONFIG_I2C_ALGOBIT=y
> # CONFIG_I2C_ALGOPCF is not set
> # CONFIG_I2C_ALGOPCA is not set
>
> #
> # I2C Hardware Bus support
> #
> # CONFIG_I2C_ALI1535 is not set
> CONFIG_I2C_ALI1563=y
> # CONFIG_I2C_ALI15X3 is not set
> # CONFIG_I2C_AMD756 is not set
> # CONFIG_I2C_AMD8111 is not set
> # CONFIG_I2C_I801 is not set
> # CONFIG_I2C_I810 is not set
> # CONFIG_I2C_PIIX4 is not set
> CONFIG_I2C_ISA=y
> # CONFIG_I2C_NFORCE2 is not set
> # CONFIG_I2C_PARPORT is not set
> # CONFIG_I2C_PARPORT_LIGHT is not set
> # CONFIG_I2C_PROSAVAGE is not set
> # CONFIG_I2C_SAVAGE4 is not set
> # CONFIG_SCx200_ACB is not set
> # CONFIG_I2C_SIS5595 is not set
> # CONFIG_I2C_SIS630 is not set
> # CONFIG_I2C_SIS96X is not set
> # CONFIG_I2C_STUB is not set
> # CONFIG_I2C_VIA is not set
> # CONFIG_I2C_VIAPRO is not set
> # CONFIG_I2C_VOODOO3 is not set
> # CONFIG_I2C_PCA_ISA is not set
>
> #
> # Miscellaneous I2C Chip support
> #
> # CONFIG_SENSORS_DS1337 is not set
> # CONFIG_SENSORS_DS1374 is not set
> CONFIG_SENSORS_EEPROM=y
> # CONFIG_SENSORS_PCF8574 is not set
> # CONFIG_SENSORS_PCA9539 is not set
> # CONFIG_SENSORS_PCF8591 is not set
> # CONFIG_SENSORS_RTC8564 is not set
> # CONFIG_SENSORS_MAX6875 is not set
> # CONFIG_RTC_X1205_I2C is not set
> # CONFIG_I2C_DEBUG_CORE is not set
> # CONFIG_I2C_DEBUG_ALGO is not set
> # CONFIG_I2C_DEBUG_BUS is not set
> # CONFIG_I2C_DEBUG_CHIP is not set
>
> #
> # Dallas's 1-wire bus
> #
> # CONFIG_W1 is not set
>
> #
> # Hardware Monitoring support
> #
> CONFIG_HWMON=y
> CONFIG_HWMON_VID=y
> # CONFIG_SENSORS_ADM1021 is not set
> # CONFIG_SENSORS_ADM1025 is not set
> # CONFIG_SENSORS_ADM1026 is not set
> # CONFIG_SENSORS_ADM1031 is not set
> # CONFIG_SENSORS_ADM9240 is not set
> # CONFIG_SENSORS_ASB100 is not set
> # CONFIG_SENSORS_ATXP1 is not set
> # CONFIG_SENSORS_DS1621 is not set
> # CONFIG_SENSORS_FSCHER is not set
> # CONFIG_SENSORS_FSCPOS is not set
> # CONFIG_SENSORS_GL518SM is not set
> # CONFIG_SENSORS_GL520SM is not set
> # CONFIG_SENSORS_IT87 is not set
> # CONFIG_SENSORS_LM63 is not set
> CONFIG_SENSORS_LM75=y
> # CONFIG_SENSORS_LM77 is not set
> # CONFIG_SENSORS_LM78 is not set
> # CONFIG_SENSORS_LM80 is not set
> # CONFIG_SENSORS_LM83 is not set
> # CONFIG_SENSORS_LM85 is not set
> # CONFIG_SENSORS_LM87 is not set
> # CONFIG_SENSORS_LM90 is not set
> # CONFIG_SENSORS_LM92 is not set
> # CONFIG_SENSORS_MAX1619 is not set
> # CONFIG_SENSORS_PC87360 is not set
> # CONFIG_SENSORS_SIS5595 is not set
> # CONFIG_SENSORS_SMSC47M1 is not set
> # CONFIG_SENSORS_SMSC47B397 is not set
> # CONFIG_SENSORS_VIA686A is not set
> # CONFIG_SENSORS_W83781D is not set
> # CONFIG_SENSORS_W83792D is not set
> # CONFIG_SENSORS_W83L785TS is not set
> CONFIG_SENSORS_W83627HF=y
> # CONFIG_SENSORS_W83627EHF is not set
> # CONFIG_SENSORS_HDAPS is not set
> # CONFIG_HWMON_DEBUG_CHIP is not set
>
> #
> # Misc devices
> #
> # CONFIG_IBM_ASM is not set
>
> #
> # Multimedia Capabilities Port drivers
> #
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
>
> #
> # Digital Video Broadcasting Devices
> #
> # CONFIG_DVB is not set
>
> #
> # Graphics support
> #
> CONFIG_FB=y
> CONFIG_FB_CFB_FILLRECT=y
> CONFIG_FB_CFB_COPYAREA=y
> CONFIG_FB_CFB_IMAGEBLIT=y
> # CONFIG_FB_MACMODES is not set
> # CONFIG_FB_MODE_HELPERS is not set
> # CONFIG_FB_TILEBLITTING is not set
> # CONFIG_FB_CIRRUS is not set
> # CONFIG_FB_PM2 is not set
> # CONFIG_FB_CYBER2000 is not set
> # CONFIG_FB_ARC is not set
> # CONFIG_FB_ASILIANT is not set
> # CONFIG_FB_IMSTT is not set
> # CONFIG_FB_VGA16 is not set
> CONFIG_FB_VESA=y
> CONFIG_VIDEO_SELECT=y
> # CONFIG_FB_HGA is not set
> # CONFIG_FB_S1D13XXX is not set
> # CONFIG_FB_NVIDIA is not set
> # CONFIG_FB_RIVA is not set
> # CONFIG_FB_MATROX is not set
> # CONFIG_FB_RADEON_OLD is not set
> # CONFIG_FB_RADEON is not set
> # CONFIG_FB_ATY128 is not set
> # CONFIG_FB_ATY is not set
> # CONFIG_FB_SAVAGE is not set
> # CONFIG_FB_SIS is not set
> # CONFIG_FB_NEOMAGIC is not set
> # CONFIG_FB_KYRO is not set
> # CONFIG_FB_3DFX is not set
> # CONFIG_FB_VOODOO1 is not set
> # CONFIG_FB_CYBLA is not set
> # CONFIG_FB_TRIDENT is not set
> # CONFIG_FB_PM3 is not set
> # CONFIG_FB_GEODE is not set
> # CONFIG_FB_VIRTUAL is not set
>
> #
> # Console display driver support
> #
> CONFIG_VGA_CONSOLE=y
> CONFIG_DUMMY_CONSOLE=y
> CONFIG_FRAMEBUFFER_CONSOLE=y
> # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> # CONFIG_FONTS is not set
> CONFIG_FONT_8x8=y
> CONFIG_FONT_8x16=y
>
> #
> # Logo configuration
> #
> CONFIG_LOGO=y
> # CONFIG_LOGO_LINUX_MONO is not set
> # CONFIG_LOGO_LINUX_VGA16 is not set
> CONFIG_LOGO_LINUX_CLUT224=y
> # CONFIG_BACKLIGHT_LCD_SUPPORT is not set
>
> #
> # Sound
> #
> CONFIG_SOUND=y
>
> #
> # Advanced Linux Sound Architecture
> #
> CONFIG_SND=y
> CONFIG_SND_AC97_CODEC=y
> CONFIG_SND_AC97_BUS=y
> CONFIG_SND_TIMER=y
> CONFIG_SND_PCM=y
> CONFIG_SND_SEQUENCER=y
> CONFIG_SND_SEQ_DUMMY=y
> CONFIG_SND_OSSEMUL=y
> CONFIG_SND_MIXER_OSS=y
> CONFIG_SND_PCM_OSS=y
> CONFIG_SND_SEQUENCER_OSS=y
> CONFIG_SND_RTCTIMER=y
> CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
> # CONFIG_SND_VERBOSE_PRINTK is not set
> # CONFIG_SND_DEBUG is not set
>
> #
> # Generic devices
> #
> # CONFIG_SND_DUMMY is not set
> # CONFIG_SND_VIRMIDI is not set
> # CONFIG_SND_MTPAV is not set
> # CONFIG_SND_SERIAL_U16550 is not set
> # CONFIG_SND_MPU401 is not set
>
> #
> # PCI devices
> #
> # CONFIG_SND_ALI5451 is not set
> # CONFIG_SND_ATIIXP is not set
> # CONFIG_SND_ATIIXP_MODEM is not set
> # CONFIG_SND_AU8810 is not set
> # CONFIG_SND_AU8820 is not set
> # CONFIG_SND_AU8830 is not set
> # CONFIG_SND_AZT3328 is not set
> # CONFIG_SND_BT87X is not set
> # CONFIG_SND_CS46XX is not set
> # CONFIG_SND_CS4281 is not set
> # CONFIG_SND_EMU10K1 is not set
> # CONFIG_SND_EMU10K1X is not set
> # CONFIG_SND_CA0106 is not set
> # CONFIG_SND_KORG1212 is not set
> # CONFIG_SND_MIXART is not set
> # CONFIG_SND_NM256 is not set
> # CONFIG_SND_RME32 is not set
> # CONFIG_SND_RME96 is not set
> # CONFIG_SND_RME9652 is not set
> # CONFIG_SND_HDSP is not set
> # CONFIG_SND_HDSPM is not set
> # CONFIG_SND_TRIDENT is not set
> # CONFIG_SND_YMFPCI is not set
> # CONFIG_SND_AD1889 is not set
> # CONFIG_SND_ALS4000 is not set
> # CONFIG_SND_CMIPCI is not set
> # CONFIG_SND_ENS1370 is not set
> # CONFIG_SND_ENS1371 is not set
> # CONFIG_SND_ES1938 is not set
> # CONFIG_SND_ES1968 is not set
> # CONFIG_SND_MAESTRO3 is not set
> # CONFIG_SND_FM801 is not set
> # CONFIG_SND_ICE1712 is not set
> # CONFIG_SND_ICE1724 is not set
> CONFIG_SND_INTEL8X0=y
> # CONFIG_SND_INTEL8X0M is not set
> # CONFIG_SND_SONICVIBES is not set
> # CONFIG_SND_VIA82XX is not set
> # CONFIG_SND_VIA82XX_MODEM is not set
> # CONFIG_SND_VX222 is not set
> # CONFIG_SND_HDA_INTEL is not set
>
> #
> # USB devices
> #
> # CONFIG_SND_USB_AUDIO is not set
> # CONFIG_SND_USB_USX2Y is not set
>
> #
> # Open Sound System
> #
> # CONFIG_SOUND_PRIME is not set
>
> #
> # USB support
> #
> CONFIG_USB_ARCH_HAS_HCD=y
> CONFIG_USB_ARCH_HAS_OHCI=y
> CONFIG_USB=y
> # CONFIG_USB_DEBUG is not set
>
> #
> # Miscellaneous USB options
> #
> CONFIG_USB_DEVICEFS=y
> # CONFIG_USB_BANDWIDTH is not set
> CONFIG_USB_DYNAMIC_MINORS=y
> CONFIG_USB_SUSPEND=y
> # CONFIG_USB_OTG is not set
>
> #
> # USB Host Controller Drivers
> #
> CONFIG_USB_EHCI_HCD=y
> CONFIG_USB_EHCI_SPLIT_ISO=y
> CONFIG_USB_EHCI_ROOT_HUB_TT=y
> # CONFIG_USB_ISP116X_HCD is not set
> CONFIG_USB_OHCI_HCD=y
> # CONFIG_USB_OHCI_BIG_ENDIAN is not set
> CONFIG_USB_OHCI_LITTLE_ENDIAN=y
> # CONFIG_USB_UHCI_HCD is not set
> # CONFIG_USB_SL811_HCD is not set
>
> #
> # USB Device Class drivers
> #
> # CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
> # CONFIG_USB_ACM is not set
> # CONFIG_USB_PRINTER is not set
>
> #
> # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
> #
>
> #
> # may also be needed; see USB_STORAGE Help for more information
> #
> CONFIG_USB_STORAGE=y
> # CONFIG_USB_STORAGE_DEBUG is not set
> # CONFIG_USB_STORAGE_DATAFAB is not set
> # CONFIG_USB_STORAGE_FREECOM is not set
> # CONFIG_USB_STORAGE_ISD200 is not set
> # CONFIG_USB_STORAGE_DPCM is not set
> # CONFIG_USB_STORAGE_USBAT is not set
> # CONFIG_USB_STORAGE_SDDR09 is not set
> # CONFIG_USB_STORAGE_SDDR55 is not set
> # CONFIG_USB_STORAGE_JUMPSHOT is not set
>
> #
> # USB Input Devices
> #
> # CONFIG_USB_HID is not set
>
> #
> # USB HID Boot Protocol drivers
> #
> # CONFIG_USB_KBD is not set
> # CONFIG_USB_MOUSE is not set
> # CONFIG_USB_AIPTEK is not set
> # CONFIG_USB_WACOM is not set
> # CONFIG_USB_ACECAD is not set
> # CONFIG_USB_KBTAB is not set
> # CONFIG_USB_POWERMATE is not set
> # CONFIG_USB_MTOUCH is not set
> # CONFIG_USB_ITMTOUCH is not set
> # CONFIG_USB_EGALAX is not set
> # CONFIG_USB_YEALINK is not set
> # CONFIG_USB_XPAD is not set
> # CONFIG_USB_ATI_REMOTE is not set
> # CONFIG_USB_KEYSPAN_REMOTE is not set
> # CONFIG_USB_APPLETOUCH is not set
>
> #
> # USB Imaging devices
> #
> # CONFIG_USB_MDC800 is not set
> # CONFIG_USB_MICROTEK is not set
>
> #
> # USB Multimedia devices
> #
> # CONFIG_USB_DABUSB is not set
>
> #
> # Video4Linux support is needed for USB Multimedia device support
> #
>
> #
> # USB Network Adapters
> #
> # CONFIG_USB_CATC is not set
> # CONFIG_USB_KAWETH is not set
> # CONFIG_USB_PEGASUS is not set
> # CONFIG_USB_RTL8150 is not set
> # CONFIG_USB_USBNET is not set
> CONFIG_USB_MON=y
>
> #
> # USB port drivers
> #
> # CONFIG_USB_USS720 is not set
>
> #
> # USB Serial Converter support
> #
> # CONFIG_USB_SERIAL is not set
>
> #
> # USB Miscellaneous drivers
> #
> # CONFIG_USB_EMI62 is not set
> # CONFIG_USB_EMI26 is not set
> # CONFIG_USB_AUERSWALD is not set
> # CONFIG_USB_RIO500 is not set
> # CONFIG_USB_LEGOTOWER is not set
> # CONFIG_USB_LCD is not set
> # CONFIG_USB_LED is not set
> # CONFIG_USB_CYTHERM is not set
> # CONFIG_USB_PHIDGETKIT is not set
> # CONFIG_USB_PHIDGETSERVO is not set
> # CONFIG_USB_IDMOUSE is not set
> # CONFIG_USB_SISUSBVGA is not set
> # CONFIG_USB_LD is not set
> # CONFIG_USB_TEST is not set
>
> #
> # USB DSL modem support
> #
>
> #
> # USB Gadget Support
> #
> # CONFIG_USB_GADGET is not set
>
> #
> # MMC/SD Card support
> #
> # CONFIG_MMC is not set
>
> #
> # InfiniBand support
> #
> # CONFIG_INFINIBAND is not set
>
> #
> # SN Devices
> #
>
> #
> # Firmware Drivers
> #
> # CONFIG_EDD is not set
> # CONFIG_DELL_RBU is not set
> # CONFIG_DCDBAS is not set
>
> #
> # File systems
> #
> CONFIG_EXT2_FS=y
> # CONFIG_EXT2_FS_XATTR is not set
> # CONFIG_EXT2_FS_XIP is not set
> CONFIG_EXT3_FS=y
> # CONFIG_EXT3_FS_XATTR is not set
> CONFIG_JBD=y
> # CONFIG_JBD_DEBUG is not set
> CONFIG_REISERFS_FS=y
> # CONFIG_REISERFS_CHECK is not set
> # CONFIG_REISERFS_PROC_INFO is not set
> # CONFIG_REISERFS_FS_XATTR is not set
> # CONFIG_JFS_FS is not set
> CONFIG_FS_POSIX_ACL=y
> # CONFIG_XFS_FS is not set
> # CONFIG_MINIX_FS is not set
> # CONFIG_ROMFS_FS is not set
> CONFIG_INOTIFY=y
> # CONFIG_QUOTA is not set
> CONFIG_DNOTIFY=y
> # CONFIG_AUTOFS_FS is not set
> CONFIG_AUTOFS4_FS=y
> CONFIG_FUSE_FS=y
>
> #
> # CD-ROM/DVD Filesystems
> #
> CONFIG_ISO9660_FS=y
> CONFIG_JOLIET=y
> CONFIG_ZISOFS=y
> CONFIG_ZISOFS_FS=y
> CONFIG_UDF_FS=y
> CONFIG_UDF_NLS=y
>
> #
> # DOS/FAT/NT Filesystems
> #
> CONFIG_FAT_FS=y
> CONFIG_MSDOS_FS=y
> CONFIG_VFAT_FS=y
> CONFIG_FAT_DEFAULT_CODEPAGE=437
> CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
> CONFIG_NTFS_FS=y
> # CONFIG_NTFS_DEBUG is not set
> CONFIG_NTFS_RW=y
>
> #
> # Pseudo filesystems
> #
> CONFIG_PROC_FS=y
> CONFIG_PROC_KCORE=y
> CONFIG_SYSFS=y
> CONFIG_TMPFS=y
> # CONFIG_HUGETLBFS is not set
> # CONFIG_HUGETLB_PAGE is not set
> CONFIG_RAMFS=y
> # CONFIG_RELAYFS_FS is not set
>
> #
> # Miscellaneous filesystems
> #
> # CONFIG_ADFS_FS is not set
> # CONFIG_AFFS_FS is not set
> # CONFIG_HFS_FS is not set
> # CONFIG_HFSPLUS_FS is not set
> # CONFIG_BEFS_FS is not set
> # CONFIG_BFS_FS is not set
> # CONFIG_EFS_FS is not set
> # CONFIG_CRAMFS is not set
> # CONFIG_VXFS_FS is not set
> # CONFIG_HPFS_FS is not set
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_SYSV_FS is not set
> # CONFIG_UFS_FS is not set
>
> #
> # Network File Systems
> #
> CONFIG_NFS_FS=y
> CONFIG_NFS_V3=y
> # CONFIG_NFS_V3_ACL is not set
> CONFIG_NFS_V4=y
> CONFIG_NFS_DIRECTIO=y
> CONFIG_NFSD=y
> CONFIG_NFSD_V3=y
> # CONFIG_NFSD_V3_ACL is not set
> CONFIG_NFSD_V4=y
> CONFIG_NFSD_TCP=y
> CONFIG_LOCKD=y
> CONFIG_LOCKD_V4=y
> CONFIG_EXPORTFS=y
> CONFIG_NFS_COMMON=y
> CONFIG_SUNRPC=y
> CONFIG_SUNRPC_GSS=y
> CONFIG_RPCSEC_GSS_KRB5=y
> # CONFIG_RPCSEC_GSS_SPKM3 is not set
> CONFIG_SMB_FS=y
> # CONFIG_SMB_NLS_DEFAULT is not set
> CONFIG_CIFS=y
> # CONFIG_CIFS_STATS is not set
> # CONFIG_CIFS_XATTR is not set
> # CONFIG_CIFS_EXPERIMENTAL is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_CODA_FS is not set
> # CONFIG_AFS_FS is not set
> # CONFIG_9P_FS is not set
>
> #
> # Partition Types
> #
> # CONFIG_PARTITION_ADVANCED is not set
> CONFIG_MSDOS_PARTITION=y
>
> #
> # Native Language Support
> #
> CONFIG_NLS=y
> CONFIG_NLS_DEFAULT="utf8"
> CONFIG_NLS_CODEPAGE_437=y
> # CONFIG_NLS_CODEPAGE_737 is not set
> # CONFIG_NLS_CODEPAGE_775 is not set
> CONFIG_NLS_CODEPAGE_850=y
> # CONFIG_NLS_CODEPAGE_852 is not set
> # CONFIG_NLS_CODEPAGE_855 is not set
> # CONFIG_NLS_CODEPAGE_857 is not set
> # CONFIG_NLS_CODEPAGE_860 is not set
> # CONFIG_NLS_CODEPAGE_861 is not set
> # CONFIG_NLS_CODEPAGE_862 is not set
> # CONFIG_NLS_CODEPAGE_863 is not set
> # CONFIG_NLS_CODEPAGE_864 is not set
> # CONFIG_NLS_CODEPAGE_865 is not set
> # CONFIG_NLS_CODEPAGE_866 is not set
> # CONFIG_NLS_CODEPAGE_869 is not set
> # CONFIG_NLS_CODEPAGE_936 is not set
> # CONFIG_NLS_CODEPAGE_950 is not set
> # CONFIG_NLS_CODEPAGE_932 is not set
> # CONFIG_NLS_CODEPAGE_949 is not set
> # CONFIG_NLS_CODEPAGE_874 is not set
> # CONFIG_NLS_ISO8859_8 is not set
> # CONFIG_NLS_CODEPAGE_1250 is not set
> # CONFIG_NLS_CODEPAGE_1251 is not set
> # CONFIG_NLS_ASCII is not set
> CONFIG_NLS_ISO8859_1=y
> # CONFIG_NLS_ISO8859_2 is not set
> # CONFIG_NLS_ISO8859_3 is not set
> # CONFIG_NLS_ISO8859_4 is not set
> # CONFIG_NLS_ISO8859_5 is not set
> # CONFIG_NLS_ISO8859_6 is not set
> # CONFIG_NLS_ISO8859_7 is not set
> # CONFIG_NLS_ISO8859_9 is not set
> # CONFIG_NLS_ISO8859_13 is not set
> # CONFIG_NLS_ISO8859_14 is not set
> # CONFIG_NLS_ISO8859_15 is not set
> # CONFIG_NLS_KOI8_R is not set
> # CONFIG_NLS_KOI8_U is not set
> CONFIG_NLS_UTF8=y
>
> #
> # Instrumentation Support
> #
> # CONFIG_PROFILING is not set
> # CONFIG_KPROBES is not set
>
> #
> # Kernel hacking
> #
> # CONFIG_PRINTK_TIME is not set
> CONFIG_DEBUG_KERNEL=y
> CONFIG_MAGIC_SYSRQ=y
> CONFIG_LOG_BUF_SHIFT=15
> # CONFIG_DETECT_SOFTLOCKUP is not set
> # CONFIG_SCHEDSTATS is not set
> # CONFIG_DEBUG_SLAB is not set
> # CONFIG_DEBUG_PREEMPT is not set
> # CONFIG_DEBUG_SPINLOCK is not set
> # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
> # CONFIG_DEBUG_KOBJECT is not set
> # CONFIG_DEBUG_INFO is not set
> # CONFIG_DEBUG_FS is not set
> # CONFIG_DEBUG_VM is not set
> # CONFIG_FRAME_POINTER is not set
> # CONFIG_RCU_TORTURE_TEST is not set
> # CONFIG_INIT_DEBUG is not set
> # CONFIG_IOMMU_DEBUG is not set
>
> #
> # Security options
> #
> # CONFIG_KEYS is not set
> # CONFIG_SECURITY is not set
>
> #
> # Cryptographic options
> #
> CONFIG_CRYPTO=y
> # CONFIG_CRYPTO_HMAC is not set
> # CONFIG_CRYPTO_NULL is not set
> # CONFIG_CRYPTO_MD4 is not set
> CONFIG_CRYPTO_MD5=y
> # CONFIG_CRYPTO_SHA1 is not set
> # CONFIG_CRYPTO_SHA256 is not set
> # CONFIG_CRYPTO_SHA512 is not set
> # CONFIG_CRYPTO_WP512 is not set
> # CONFIG_CRYPTO_TGR192 is not set
> CONFIG_CRYPTO_DES=y
> # CONFIG_CRYPTO_BLOWFISH is not set
> # CONFIG_CRYPTO_TWOFISH is not set
> # CONFIG_CRYPTO_SERPENT is not set
> # CONFIG_CRYPTO_AES_X86_64 is not set
> # CONFIG_CRYPTO_CAST5 is not set
> # CONFIG_CRYPTO_CAST6 is not set
> # CONFIG_CRYPTO_TEA is not set
> # CONFIG_CRYPTO_ARC4 is not set
> # CONFIG_CRYPTO_KHAZAD is not set
> # CONFIG_CRYPTO_ANUBIS is not set
> # CONFIG_CRYPTO_DEFLATE is not set
> # CONFIG_CRYPTO_MICHAEL_MIC is not set
> # CONFIG_CRYPTO_CRC32C is not set
> # CONFIG_CRYPTO_TEST is not set
>
> #
> # Hardware crypto devices
> #
>
> #
> # Library routines
> #
> # CONFIG_CRC_CCITT is not set
> # CONFIG_CRC16 is not set
> CONFIG_CRC32=y
> # CONFIG_LIBCRC32C is not set
> CONFIG_ZLIB_INFLATE=y

2006-03-28 17:31:48

by Prakash Punnoor

[permalink] [raw]
Subject: Re: Issues with uli526x networking module

Am Donnerstag Januar 26 2006 12:10 schrieb Nigel Cunningham:
> Hi.
>
> On Thursday 26 January 2006 18:00, Prakash Punnoor wrote:
> > Hi,
> >
> > I have some problems with the uli526x driver. (I cc'ed the tulip
> > maintainer, as the driver is found in this category.)
> >
> > - It doesn't detect link when cable is plugged in, if module/driver is
> > loaded with no cable attached. I have to rmmod the module, plug in cable,
> > insmod the module and then set up the interface to get it running. That's
> > the only reason I compiled this driver as a module...(BTW, it is not
> > AMD64 related, as I experienced this also in x86.)
> >
> > - dhcpcd doesn't work. dhclient does though (but it is slow, I can't find
> > the correct parameters to speed it up). The former gets no response from
> > the dhcp server. I don't think it is a problem with the dhcp server, as
> > dhcpcd works from a notebook with some dlink pcmcia 10mbit interface.
> >
> >
> > Beside above, it seems to work fine, though.
>
> I have one too, and have done some work toward implementing power
> management support (working, but needs further work). I've noticed the link
> issue and will see if I can address it too. Regarding dhcpcd, I haven't
> used it, but will see if I can test before sending the patches to Jeff and
> to Peer Chen.

Hi, I am just wondering whether you found out what the issue is with the link
problem. If you have some patch ready (even if it is hackish) I would be
happy to use it.

Anyways, I know you are busy with swsusp2. ;-)

Cheers,
--
(°= =°)
//\ Prakash Punnoor /\\
V_/ \_V


Attachments:
(No filename) (1.58 kB)
(No filename) (191.00 B)
Download all attachments

2006-03-28 21:49:07

by Nigel Cunningham

[permalink] [raw]
Subject: Re: Issues with uli526x networking module

Hi.

On Wednesday 29 March 2006 03:30, Prakash Punnoor wrote:
> Hi, I am just wondering whether you found out what the issue is with the
> link problem. If you have some patch ready (even if it is hackish) I would
> be happy to use it.
>
> Anyways, I know you are busy with swsusp2. ;-)
>
> Cheers,

Yes, I do have a patch. It is hackish at the moment because as you've rightly
guessed, I haven't gotten around to finishing it. It also doesn't work
perfectly - I sometimes need to rmmod and insmod after booting a new kernel
to get the link to come up. But, apart from that, it works fine. Attached.
(Jeff, I'm sure it doesn't need saying, but please don't apply!)

Regards,

Nigel


Attachments:
(No filename) (0.00 B)
(No filename) (189.00 B)
Download all attachments