Convert the i.MX thermal binding to DT schema format using json-schema
Signed-off-by: Anson Huang <[email protected]>
---
Changes since V1:
- make clock property optional.
---
.../devicetree/bindings/thermal/imx-thermal.txt | 61 --------------
.../devicetree/bindings/thermal/imx-thermal.yaml | 96 ++++++++++++++++++++++
2 files changed, 96 insertions(+), 61 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/thermal/imx-thermal.txt
create mode 100644 Documentation/devicetree/bindings/thermal/imx-thermal.yaml
diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
deleted file mode 100644
index 823e417..0000000
--- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
+++ /dev/null
@@ -1,61 +0,0 @@
-* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
-
-Required properties:
-- compatible : must be one of following:
- - "fsl,imx6q-tempmon" for i.MX6Q,
- - "fsl,imx6sx-tempmon" for i.MX6SX,
- - "fsl,imx7d-tempmon" for i.MX7S/D.
-- interrupts : the interrupt output of the controller:
- i.MX6Q has one IRQ which will be triggered when temperature is higher than high threshold,
- i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC,
- when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature
- is higher than panic threshold, system will auto reboot by SRC module.
-- fsl,tempmon : phandle pointer to system controller that contains TEMPMON
- control registers, e.g. ANATOP on imx6q.
-- nvmem-cells: A phandle to the calibration cells provided by ocotp.
-- nvmem-cell-names: Should be "calib", "temp_grade".
-
-Deprecated properties:
-- fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON
- calibration data, e.g. OCOTP on imx6q. The details about calibration data
- can be found in SoC Reference Manual.
-
-Direct access to OCOTP via fsl,tempmon-data is incorrect on some newer chips
-because it does not handle OCOTP clock requirements.
-
-Optional properties:
-- clocks : thermal sensor's clock source.
-
-Example:
-ocotp: ocotp@21bc000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,imx6sx-ocotp", "syscon";
- reg = <0x021bc000 0x4000>;
- clocks = <&clks IMX6SX_CLK_OCOTP>;
-
- tempmon_calib: calib@38 {
- reg = <0x38 4>;
- };
-
- tempmon_temp_grade: temp-grade@20 {
- reg = <0x20 4>;
- };
-};
-
-tempmon: tempmon {
- compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
- interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
- fsl,tempmon = <&anatop>;
- nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
- nvmem-cell-names = "calib", "temp_grade";
- clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
-};
-
-Legacy method (Deprecated):
-tempmon {
- compatible = "fsl,imx6q-tempmon";
- fsl,tempmon = <&anatop>;
- fsl,tempmon-data = <&ocotp>;
- clocks = <&clks 172>;
-};
diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
new file mode 100644
index 0000000..193c7e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/imx-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX Thermal Binding
+
+maintainers:
+ - Anson Huang <[email protected]>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - fsl,imx6q-tempmon
+ - fsl,imx6sx-tempmon
+ - fsl,imx7d-tempmon
+
+ interrupts:
+ description: |
+ The interrupt output of the controller, the IRQ will be triggered
+ when temperature is higher than high threshold.
+ maxItems: 1
+
+ nvmem-cells:
+ description: |
+ Phandle to the calibration cells provided by ocotp for calibration
+ data and temperature grade.
+ maxItems: 2
+
+ nvmem-cell-names:
+ maxItems: 2
+ items:
+ - const: calib
+ - const: temp_grade
+
+ fsl,tempmon:
+ $ref: '/schemas/types.yaml#/definitions/phandle'
+ description: |
+ Phandle pointer to system controller that contains TEMPMON control
+ registers, e.g. ANATOP on imx6q.
+
+ fsl,tempmon-data:
+ $ref: '/schemas/types.yaml#/definitions/phandle'
+ description: |
+ Deprecated property, phandle pointer to fuse controller that contains
+ TEMPMON calibration data, e.g. OCOTP on imx6q. The details about
+ calibration data can be found in SoC Reference Manual.
+
+ clocks:
+ description: |
+ Thermal sensor's clock source, it is optional.
+ maxItems: 1
+
+required:
+ - compatible
+ - interrupts
+ - fsl,tempmon
+ - nvmem-cells
+ - nvmem-cell-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx6sx-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ ocotp: ocotp@21bc000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,imx6sx-ocotp", "syscon";
+ reg = <0x021bc000 0x4000>;
+ clocks = <&clks IMX6SX_CLK_OCOTP>;
+
+ tempmon_calib: calib@38 {
+ reg = <0x38 4>;
+ };
+
+ tempmon_temp_grade: temp-grade@20 {
+ reg = <0x20 4>;
+ };
+ };
+
+ tempmon: tempmon {
+ compatible = "fsl,imx6sx-tempmon";
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,tempmon = <&anatop>;
+ nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+ nvmem-cell-names = "calib", "temp_grade";
+ clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+ };
+
+...
--
2.7.4
On Fri, Apr 10, 2020 at 09:07:24AM +0800, Anson Huang wrote:
> Convert the i.MX thermal binding to DT schema format using json-schema
>
> Signed-off-by: Anson Huang <[email protected]>
> ---
> Changes since V1:
> - make clock property optional.
> ---
> .../devicetree/bindings/thermal/imx-thermal.txt | 61 --------------
> .../devicetree/bindings/thermal/imx-thermal.yaml | 96 ++++++++++++++++++++++
> 2 files changed, 96 insertions(+), 61 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/thermal/imx-thermal.txt
> create mode 100644 Documentation/devicetree/bindings/thermal/imx-thermal.yaml
>
> diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> deleted file mode 100644
> index 823e417..0000000
> --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> +++ /dev/null
> @@ -1,61 +0,0 @@
> -* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
> -
> -Required properties:
> -- compatible : must be one of following:
> - - "fsl,imx6q-tempmon" for i.MX6Q,
> - - "fsl,imx6sx-tempmon" for i.MX6SX,
> - - "fsl,imx7d-tempmon" for i.MX7S/D.
> -- interrupts : the interrupt output of the controller:
> - i.MX6Q has one IRQ which will be triggered when temperature is higher than high threshold,
> - i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC,
> - when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature
> - is higher than panic threshold, system will auto reboot by SRC module.
> -- fsl,tempmon : phandle pointer to system controller that contains TEMPMON
> - control registers, e.g. ANATOP on imx6q.
> -- nvmem-cells: A phandle to the calibration cells provided by ocotp.
> -- nvmem-cell-names: Should be "calib", "temp_grade".
> -
> -Deprecated properties:
> -- fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON
> - calibration data, e.g. OCOTP on imx6q. The details about calibration data
> - can be found in SoC Reference Manual.
> -
> -Direct access to OCOTP via fsl,tempmon-data is incorrect on some newer chips
> -because it does not handle OCOTP clock requirements.
> -
> -Optional properties:
> -- clocks : thermal sensor's clock source.
> -
> -Example:
> -ocotp: ocotp@21bc000 {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - compatible = "fsl,imx6sx-ocotp", "syscon";
> - reg = <0x021bc000 0x4000>;
> - clocks = <&clks IMX6SX_CLK_OCOTP>;
> -
> - tempmon_calib: calib@38 {
> - reg = <0x38 4>;
> - };
> -
> - tempmon_temp_grade: temp-grade@20 {
> - reg = <0x20 4>;
> - };
> -};
> -
> -tempmon: tempmon {
> - compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
> - interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
> - fsl,tempmon = <&anatop>;
> - nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
> - nvmem-cell-names = "calib", "temp_grade";
> - clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
> -};
> -
> -Legacy method (Deprecated):
> -tempmon {
> - compatible = "fsl,imx6q-tempmon";
> - fsl,tempmon = <&anatop>;
> - fsl,tempmon-data = <&ocotp>;
> - clocks = <&clks 172>;
> -};
> diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> new file mode 100644
> index 0000000..193c7e5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> @@ -0,0 +1,96 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/thermal/imx-thermal.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP i.MX Thermal Binding
> +
> +maintainers:
> + - Anson Huang <[email protected]>
> +
> +properties:
> + compatible:
> + oneOf:
> + - items:
> + - enum:
> + - fsl,imx6q-tempmon
> + - fsl,imx6sx-tempmon
> + - fsl,imx7d-tempmon
> +
> + interrupts:
> + description: |
> + The interrupt output of the controller, the IRQ will be triggered
> + when temperature is higher than high threshold.
> + maxItems: 1
> +
> + nvmem-cells:
> + description: |
> + Phandle to the calibration cells provided by ocotp for calibration
> + data and temperature grade.
> + maxItems: 2
> +
> + nvmem-cell-names:
> + maxItems: 2
> + items:
> + - const: calib
> + - const: temp_grade
> +
> + fsl,tempmon:
> + $ref: '/schemas/types.yaml#/definitions/phandle'
> + description: |
> + Phandle pointer to system controller that contains TEMPMON control
> + registers, e.g. ANATOP on imx6q.
Really, this should have been a child of the system controller. Not too
late to do that, but you'd need to keep this for compatibility.
> +
> + fsl,tempmon-data:
> + $ref: '/schemas/types.yaml#/definitions/phandle'
> + description: |
> + Deprecated property, phandle pointer to fuse controller that contains
> + TEMPMON calibration data, e.g. OCOTP on imx6q. The details about
> + calibration data can be found in SoC Reference Manual.
Use 'deprecated: true' for deprecated properties.
> +
> + clocks:
> + description: |
> + Thermal sensor's clock source, it is optional.
> + maxItems: 1
> +
> +required:
> + - compatible
> + - interrupts
> + - fsl,tempmon
> + - nvmem-cells
> + - nvmem-cell-names
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/imx6sx-clock.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + ocotp: ocotp@21bc000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,imx6sx-ocotp", "syscon";
> + reg = <0x021bc000 0x4000>;
> + clocks = <&clks IMX6SX_CLK_OCOTP>;
> +
> + tempmon_calib: calib@38 {
> + reg = <0x38 4>;
> + };
> +
> + tempmon_temp_grade: temp-grade@20 {
> + reg = <0x20 4>;
> + };
> + };
> +
> + tempmon: tempmon {
> + compatible = "fsl,imx6sx-tempmon";
> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
> + fsl,tempmon = <&anatop>;
> + nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
> + nvmem-cell-names = "calib", "temp_grade";
> + clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
> + };
> +
> +...
> --
> 2.7.4
>
Hi, Rob
> Subject: Re: [PATCH V2] dt-bindings: thermal: Convert i.MX to json-schema
>
> On Fri, Apr 10, 2020 at 09:07:24AM +0800, Anson Huang wrote:
> > Convert the i.MX thermal binding to DT schema format using json-schema
> >
> > Signed-off-by: Anson Huang <[email protected]>
> > ---
> > Changes since V1:
> > - make clock property optional.
> > ---
> > .../devicetree/bindings/thermal/imx-thermal.txt | 61 --------------
> > .../devicetree/bindings/thermal/imx-thermal.yaml | 96
> ++++++++++++++++++++++
> > 2 files changed, 96 insertions(+), 61 deletions(-) delete mode
> > 100644 Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > create mode 100644
> > Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > deleted file mode 100644
> > index 823e417..0000000
> > +
> > +title: NXP i.MX Thermal Binding
> > +
> > +maintainers:
> > + - Anson Huang <[email protected]>
> > +
> > +properties:
> > + compatible:
> > + oneOf:
> > + - items:
> > + - enum:
> > + - fsl,imx6q-tempmon
> > + - fsl,imx6sx-tempmon
> > + - fsl,imx7d-tempmon
> > +
> > + interrupts:
> > + description: |
> > + The interrupt output of the controller, the IRQ will be triggered
> > + when temperature is higher than high threshold.
> > + maxItems: 1
> > +
> > + nvmem-cells:
> > + description: |
> > + Phandle to the calibration cells provided by ocotp for calibration
> > + data and temperature grade.
> > + maxItems: 2
> > +
> > + nvmem-cell-names:
> > + maxItems: 2
> > + items:
> > + - const: calib
> > + - const: temp_grade
> > +
> > + fsl,tempmon:
> > + $ref: '/schemas/types.yaml#/definitions/phandle'
> > + description: |
> > + Phandle pointer to system controller that contains TEMPMON
> control
> > + registers, e.g. ANATOP on imx6q.
>
> Really, this should have been a child of the system controller. Not too late to
> do that, but you'd need to keep this for compatibility.
Sorry, I don't quite get your point, can you provide more details or example, thanks.
Anson
Hi, Rob
> Subject: RE: [PATCH V2] dt-bindings: thermal: Convert i.MX to json-schema
>
> Hi, Rob
>
>
> > Subject: Re: [PATCH V2] dt-bindings: thermal: Convert i.MX to
> > json-schema
> >
> > On Fri, Apr 10, 2020 at 09:07:24AM +0800, Anson Huang wrote:
> > > Convert the i.MX thermal binding to DT schema format using
> > > json-schema
> > >
> > > Signed-off-by: Anson Huang <[email protected]>
> > > ---
> > > Changes since V1:
> > > - make clock property optional.
> > > ---
> > > .../devicetree/bindings/thermal/imx-thermal.txt | 61 --------------
> > > .../devicetree/bindings/thermal/imx-thermal.yaml | 96
> > ++++++++++++++++++++++
> > > 2 files changed, 96 insertions(+), 61 deletions(-) delete mode
> > > 100644 Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > > create mode 100644
> > > Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > > b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > > deleted file mode 100644
> > > index 823e417..0000000
> > > +
> > > +title: NXP i.MX Thermal Binding
> > > +
> > > +maintainers:
> > > + - Anson Huang <[email protected]>
> > > +
> > > +properties:
> > > + compatible:
> > > + oneOf:
> > > + - items:
> > > + - enum:
> > > + - fsl,imx6q-tempmon
> > > + - fsl,imx6sx-tempmon
> > > + - fsl,imx7d-tempmon
> > > +
> > > + interrupts:
> > > + description: |
> > > + The interrupt output of the controller, the IRQ will be triggered
> > > + when temperature is higher than high threshold.
> > > + maxItems: 1
> > > +
> > > + nvmem-cells:
> > > + description: |
> > > + Phandle to the calibration cells provided by ocotp for calibration
> > > + data and temperature grade.
> > > + maxItems: 2
> > > +
> > > + nvmem-cell-names:
> > > + maxItems: 2
> > > + items:
> > > + - const: calib
> > > + - const: temp_grade
> > > +
> > > + fsl,tempmon:
> > > + $ref: '/schemas/types.yaml#/definitions/phandle'
> > > + description: |
> > > + Phandle pointer to system controller that contains TEMPMON
> > control
> > > + registers, e.g. ANATOP on imx6q.
> >
> > Really, this should have been a child of the system controller. Not
> > too late to do that, but you'd need to keep this for compatibility.
>
> Sorry, I don't quite get your point, can you provide more details or example,
> thanks.
I guess you meant the tempmon node should be put inside anatop node? Then
DT files also needs to be changed? Right?
anatop: anatop@20c8000 {
compatible = "fsl,imx6sx-anatop", "fsl,imx6q-anatop",
"syscon", "simple-mfd";
reg = <0x020c8000 0x1000>;
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
...
};
tempmon: tempmon {
compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
interrupt-parent = <&gpc>;
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
fsl,tempmon = <&anatop>;
nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
nvmem-cell-names = "calib", "temp_grade";
clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
};
Thanks,
Anson