From: Alex Leibovich <[email protected]>
Automatic Clock Gating is a feature used for the power
consumption optimisation. It turned out that
during early init phase it may prevent the stable voltage
switch to 1.8V - due to that on some platfroms an endless
printout in dmesg can be observed:
"mmc1: 1.8V regulator output did not became stable"
Fix the problem by disabling the ACG at very beginning
of the sdhci_init and let that be enabled later.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <[email protected]>
Signed-off-by: Marcin Wojtas <[email protected]>
Cc: [email protected]
---
drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
index c67611fdaa8a..4b05f6fdefb4 100644
--- a/drivers/mmc/host/sdhci-xenon.c
+++ b/drivers/mmc/host/sdhci-xenon.c
@@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
/* Disable tuning request and auto-retuning again */
xenon_retune_setup(host);
- xenon_set_acg(host, true);
+ /*
+ * The ACG should be turned off at the early init time, in order
+ * to solve a possile issues with the 1.8V regulator stabilization.
+ * The feature is enabled in later stage.
+ */
+ xenon_set_acg(host, false);
xenon_set_sdclk_off_idle(host, sdhc_id, false);
--
2.29.0
On 11/12/20 4:16 pm, Marcin Wojtas wrote:
> From: Alex Leibovich <[email protected]>
>
> Automatic Clock Gating is a feature used for the power
> consumption optimisation. It turned out that
> during early init phase it may prevent the stable voltage
> switch to 1.8V - due to that on some platfroms an endless
platfroms -> platforms
> printout in dmesg can be observed:
> "mmc1: 1.8V regulator output did not became stable"
> Fix the problem by disabling the ACG at very beginning
> of the sdhci_init and let that be enabled later.
>
> Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> Signed-off-by: Alex Leibovich <[email protected]>
> Signed-off-by: Marcin Wojtas <[email protected]>
> Cc: [email protected]
Acked-by: Adrian Hunter <[email protected]>
> ---
> drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> index c67611fdaa8a..4b05f6fdefb4 100644
> --- a/drivers/mmc/host/sdhci-xenon.c
> +++ b/drivers/mmc/host/sdhci-xenon.c
> @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> /* Disable tuning request and auto-retuning again */
> xenon_retune_setup(host);
>
> - xenon_set_acg(host, true);
> + /*
> + * The ACG should be turned off at the early init time, in order
> + * to solve a possile issues with the 1.8V regulator stabilization.
a possile -> possible
> + * The feature is enabled in later stage.
> + */
> + xenon_set_acg(host, false);
>
> xenon_set_sdclk_off_idle(host, sdhc_id, false);
>
>
wt., 15 gru 2020 o 09:04 Adrian Hunter <[email protected]> napisał(a):
>
> On 11/12/20 4:16 pm, Marcin Wojtas wrote:
> > From: Alex Leibovich <[email protected]>
> >
> > Automatic Clock Gating is a feature used for the power
> > consumption optimisation. It turned out that
> > during early init phase it may prevent the stable voltage
> > switch to 1.8V - due to that on some platfroms an endless
>
> platfroms -> platforms
>
> > printout in dmesg can be observed:
> > "mmc1: 1.8V regulator output did not became stable"
> > Fix the problem by disabling the ACG at very beginning
> > of the sdhci_init and let that be enabled later.
> >
> > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > Signed-off-by: Alex Leibovich <[email protected]>
> > Signed-off-by: Marcin Wojtas <[email protected]>
> > Cc: [email protected]
>
> Acked-by: Adrian Hunter <[email protected]>
>
Thank you, I'll repost right away with the typos correction.
Best regards,
Marcin
> > ---
> > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > index c67611fdaa8a..4b05f6fdefb4 100644
> > --- a/drivers/mmc/host/sdhci-xenon.c
> > +++ b/drivers/mmc/host/sdhci-xenon.c
> > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > /* Disable tuning request and auto-retuning again */
> > xenon_retune_setup(host);
> >
> > - xenon_set_acg(host, true);
> > + /*
> > + * The ACG should be turned off at the early init time, in order
> > + * to solve a possile issues with the 1.8V regulator stabilization.
>
> a possile -> possible
>
> > + * The feature is enabled in later stage.
> > + */
> > + xenon_set_acg(host, false);
> >
> > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> >
> >
>
On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
>
> From: Alex Leibovich <[email protected]>
>
> Automatic Clock Gating is a feature used for the power
> consumption optimisation. It turned out that
> during early init phase it may prevent the stable voltage
> switch to 1.8V - due to that on some platfroms an endless
> printout in dmesg can be observed:
> "mmc1: 1.8V regulator output did not became stable"
> Fix the problem by disabling the ACG at very beginning
> of the sdhci_init and let that be enabled later.
>
> Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> Signed-off-by: Alex Leibovich <[email protected]>
> Signed-off-by: Marcin Wojtas <[email protected]>
> Cc: [email protected]
Applied for fixes (by fixing the typos), thanks!
Kind regards
Uffe
> ---
> drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> index c67611fdaa8a..4b05f6fdefb4 100644
> --- a/drivers/mmc/host/sdhci-xenon.c
> +++ b/drivers/mmc/host/sdhci-xenon.c
> @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> /* Disable tuning request and auto-retuning again */
> xenon_retune_setup(host);
>
> - xenon_set_acg(host, true);
> + /*
> + * The ACG should be turned off at the early init time, in order
> + * to solve a possile issues with the 1.8V regulator stabilization.
> + * The feature is enabled in later stage.
> + */
> + xenon_set_acg(host, false);
>
> xenon_set_sdclk_off_idle(host, sdhc_id, false);
>
> --
> 2.29.0
>
Hi Pali,
pon., 14 mar 2022 o 16:40 Pali Rohár <[email protected]> napisał(a):
>
> On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> > On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> > >
> > > From: Alex Leibovich <[email protected]>
> > >
> > > Automatic Clock Gating is a feature used for the power
> > > consumption optimisation. It turned out that
> > > during early init phase it may prevent the stable voltage
> > > switch to 1.8V - due to that on some platfroms an endless
> > > printout in dmesg can be observed:
> > > "mmc1: 1.8V regulator output did not became stable"
> > > Fix the problem by disabling the ACG at very beginning
> > > of the sdhci_init and let that be enabled later.
> > >
> > > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > > Signed-off-by: Alex Leibovich <[email protected]>
> > > Signed-off-by: Marcin Wojtas <[email protected]>
> > > Cc: [email protected]
> >
> > Applied for fixes (by fixing the typos), thanks!
>
> Hello!
>
> Is not this patch address same issue which was fixed by patch which was
> merged earlier?
>
> bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
> https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
>
This indeed look similar. This fix was originally developed for CN913x
platform without the mentioned patch (I'm wondering if it would also
suffice to fix A3k board's problem). Anyway, I don't think we have an
issue here, as everything seems to work fine on top of mainline Linux
with both changes.
Best regards,
Marcin
> > Kind regards
> > Uffe
> >
> >
> > > ---
> > > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > > 1 file changed, 6 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > > index c67611fdaa8a..4b05f6fdefb4 100644
> > > --- a/drivers/mmc/host/sdhci-xenon.c
> > > +++ b/drivers/mmc/host/sdhci-xenon.c
> > > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > > /* Disable tuning request and auto-retuning again */
> > > xenon_retune_setup(host);
> > >
> > > - xenon_set_acg(host, true);
> > > + /*
> > > + * The ACG should be turned off at the early init time, in order
> > > + * to solve a possile issues with the 1.8V regulator stabilization.
> > > + * The feature is enabled in later stage.
> > > + */
> > > + xenon_set_acg(host, false);
> > >
> > > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> > >
> > > --
> > > 2.29.0
> > >
Hi Pali,
śr., 16 mar 2022 o 00:03 Pali Rohár <[email protected]> napisał(a):
>
> Hello!
>
> On Monday 14 March 2022 16:51:25 Marcin Wojtas wrote:
> > Hi Pali,
> >
> >
> > pon., 14 mar 2022 o 16:40 Pali Rohár <[email protected]> napisał(a):
> > >
> > > On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> > > > On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> > > > >
> > > > > From: Alex Leibovich <[email protected]>
> > > > >
> > > > > Automatic Clock Gating is a feature used for the power
> > > > > consumption optimisation. It turned out that
> > > > > during early init phase it may prevent the stable voltage
> > > > > switch to 1.8V - due to that on some platfroms an endless
> > > > > printout in dmesg can be observed:
> > > > > "mmc1: 1.8V regulator output did not became stable"
> > > > > Fix the problem by disabling the ACG at very beginning
> > > > > of the sdhci_init and let that be enabled later.
> > > > >
> > > > > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > > > > Signed-off-by: Alex Leibovich <[email protected]>
> > > > > Signed-off-by: Marcin Wojtas <[email protected]>
> > > > > Cc: [email protected]
> > > >
> > > > Applied for fixes (by fixing the typos), thanks!
> > >
> > > Hello!
> > >
> > > Is not this patch address same issue which was fixed by patch which was
> > > merged earlier?
> > >
> > > bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
> > > https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
> > >
> >
> > This indeed look similar. This fix was originally developed for CN913x
> > platform without the mentioned patch (I'm wondering if it would also
> > suffice to fix A3k board's problem). Anyway, I don't think we have an
> > issue here, as everything seems to work fine on top of mainline Linux
> > with both changes.
>
> Yea, there should be no issue. Just question is if we need _both_ fixes.
>
> I could probably try to revert bb32e1987bc5 and check what happens on
> A3k board.
>
Yes, that would be interesting. Please let me know whenever you find
time to check.
Best regards,
Marcin
> > > >
> > > >
> > > > > ---
> > > > > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > > > > 1 file changed, 6 insertions(+), 1 deletion(-)
> > > > >
> > > > > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > > > > index c67611fdaa8a..4b05f6fdefb4 100644
> > > > > --- a/drivers/mmc/host/sdhci-xenon.c
> > > > > +++ b/drivers/mmc/host/sdhci-xenon.c
> > > > > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > > > > /* Disable tuning request and auto-retuning again */
> > > > > xenon_retune_setup(host);
> > > > >
> > > > > - xenon_set_acg(host, true);
> > > > > + /*
> > > > > + * The ACG should be turned off at the early init time, in order
> > > > > + * to solve a possile issues with the 1.8V regulator stabilization.
> > > > > + * The feature is enabled in later stage.
> > > > > + */
> > > > > + xenon_set_acg(host, false);
> > > > >
> > > > > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> > > > >
> > > > > --
> > > > > 2.29.0
> > > > >
On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> >
> > From: Alex Leibovich <[email protected]>
> >
> > Automatic Clock Gating is a feature used for the power
> > consumption optimisation. It turned out that
> > during early init phase it may prevent the stable voltage
> > switch to 1.8V - due to that on some platfroms an endless
> > printout in dmesg can be observed:
> > "mmc1: 1.8V regulator output did not became stable"
> > Fix the problem by disabling the ACG at very beginning
> > of the sdhci_init and let that be enabled later.
> >
> > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > Signed-off-by: Alex Leibovich <[email protected]>
> > Signed-off-by: Marcin Wojtas <[email protected]>
> > Cc: [email protected]
>
> Applied for fixes (by fixing the typos), thanks!
Hello!
Is not this patch address same issue which was fixed by patch which was
merged earlier?
bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
> Kind regards
> Uffe
>
>
> > ---
> > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > index c67611fdaa8a..4b05f6fdefb4 100644
> > --- a/drivers/mmc/host/sdhci-xenon.c
> > +++ b/drivers/mmc/host/sdhci-xenon.c
> > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > /* Disable tuning request and auto-retuning again */
> > xenon_retune_setup(host);
> >
> > - xenon_set_acg(host, true);
> > + /*
> > + * The ACG should be turned off at the early init time, in order
> > + * to solve a possile issues with the 1.8V regulator stabilization.
> > + * The feature is enabled in later stage.
> > + */
> > + xenon_set_acg(host, false);
> >
> > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> >
> > --
> > 2.29.0
> >
Hello!
On Monday 14 March 2022 16:51:25 Marcin Wojtas wrote:
> Hi Pali,
>
>
> pon., 14 mar 2022 o 16:40 Pali Rohár <[email protected]> napisał(a):
> >
> > On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> > > On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> > > >
> > > > From: Alex Leibovich <[email protected]>
> > > >
> > > > Automatic Clock Gating is a feature used for the power
> > > > consumption optimisation. It turned out that
> > > > during early init phase it may prevent the stable voltage
> > > > switch to 1.8V - due to that on some platfroms an endless
> > > > printout in dmesg can be observed:
> > > > "mmc1: 1.8V regulator output did not became stable"
> > > > Fix the problem by disabling the ACG at very beginning
> > > > of the sdhci_init and let that be enabled later.
> > > >
> > > > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > > > Signed-off-by: Alex Leibovich <[email protected]>
> > > > Signed-off-by: Marcin Wojtas <[email protected]>
> > > > Cc: [email protected]
> > >
> > > Applied for fixes (by fixing the typos), thanks!
> >
> > Hello!
> >
> > Is not this patch address same issue which was fixed by patch which was
> > merged earlier?
> >
> > bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
> > https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
> >
>
> This indeed look similar. This fix was originally developed for CN913x
> platform without the mentioned patch (I'm wondering if it would also
> suffice to fix A3k board's problem). Anyway, I don't think we have an
> issue here, as everything seems to work fine on top of mainline Linux
> with both changes.
Yea, there should be no issue. Just question is if we need _both_ fixes.
I could probably try to revert bb32e1987bc5 and check what happens on
A3k board.
> Best regards,
> Marcin
>
> > > Kind regards
> > > Uffe
> > >
> > >
> > > > ---
> > > > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > > > 1 file changed, 6 insertions(+), 1 deletion(-)
> > > >
> > > > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > > > index c67611fdaa8a..4b05f6fdefb4 100644
> > > > --- a/drivers/mmc/host/sdhci-xenon.c
> > > > +++ b/drivers/mmc/host/sdhci-xenon.c
> > > > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > > > /* Disable tuning request and auto-retuning again */
> > > > xenon_retune_setup(host);
> > > >
> > > > - xenon_set_acg(host, true);
> > > > + /*
> > > > + * The ACG should be turned off at the early init time, in order
> > > > + * to solve a possile issues with the 1.8V regulator stabilization.
> > > > + * The feature is enabled in later stage.
> > > > + */
> > > > + xenon_set_acg(host, false);
> > > >
> > > > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> > > >
> > > > --
> > > > 2.29.0
> > > >
On Friday 18 March 2022 14:01:00 Pali Rohár wrote:
> On Wednesday 16 March 2022 02:03:35 Marcin Wojtas wrote:
> > Hi Pali,
> >
> > śr., 16 mar 2022 o 00:03 Pali Rohár <[email protected]> napisał(a):
> > >
> > > Hello!
> > >
> > > On Monday 14 March 2022 16:51:25 Marcin Wojtas wrote:
> > > > Hi Pali,
> > > >
> > > >
> > > > pon., 14 mar 2022 o 16:40 Pali Rohár <[email protected]> napisał(a):
> > > > >
> > > > > On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> > > > > > On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> > > > > > >
> > > > > > > From: Alex Leibovich <[email protected]>
> > > > > > >
> > > > > > > Automatic Clock Gating is a feature used for the power
> > > > > > > consumption optimisation. It turned out that
> > > > > > > during early init phase it may prevent the stable voltage
> > > > > > > switch to 1.8V - due to that on some platfroms an endless
> > > > > > > printout in dmesg can be observed:
> > > > > > > "mmc1: 1.8V regulator output did not became stable"
> > > > > > > Fix the problem by disabling the ACG at very beginning
> > > > > > > of the sdhci_init and let that be enabled later.
> > > > > > >
> > > > > > > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > > > > > > Signed-off-by: Alex Leibovich <[email protected]>
> > > > > > > Signed-off-by: Marcin Wojtas <[email protected]>
> > > > > > > Cc: [email protected]
> > > > > >
> > > > > > Applied for fixes (by fixing the typos), thanks!
> > > > >
> > > > > Hello!
> > > > >
> > > > > Is not this patch address same issue which was fixed by patch which was
> > > > > merged earlier?
> > > > >
> > > > > bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
> > > > > https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
> > > > >
> > > >
> > > > This indeed look similar. This fix was originally developed for CN913x
> > > > platform without the mentioned patch (I'm wondering if it would also
> > > > suffice to fix A3k board's problem). Anyway, I don't think we have an
> > > > issue here, as everything seems to work fine on top of mainline Linux
> > > > with both changes.
> > >
> > > Yea, there should be no issue. Just question is if we need _both_ fixes.
> > >
> > > I could probably try to revert bb32e1987bc5 and check what happens on
> > > A3k board.
> > >
> >
> > Yes, that would be interesting. Please let me know whenever you find
> > time to check.
>
> Hello! Now I tested kernel with reverted commit bb32e1987bc5 ("mmc:
> sdhci-xenon: fix annoying 1.8V regulator warning") and issue is still
> fixed. I reverted also bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying
> 1.8V regulator warning") commit and then issue appeared again.
I mean that I reverted also 1a3ed0dc3594 ("mmc: sdhci-xenon: fix 1.8v
regulator stabilization") commit and then issue appeared again.
> So any of this commit is fixing that issue on Armada 3720.
>
> Should we revert one of them?
>
> > Best regards,
> > Marcin
> >
> > > > > >
> > > > > >
> > > > > > > ---
> > > > > > > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > > > > > > 1 file changed, 6 insertions(+), 1 deletion(-)
> > > > > > >
> > > > > > > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > > > > > > index c67611fdaa8a..4b05f6fdefb4 100644
> > > > > > > --- a/drivers/mmc/host/sdhci-xenon.c
> > > > > > > +++ b/drivers/mmc/host/sdhci-xenon.c
> > > > > > > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > > > > > > /* Disable tuning request and auto-retuning again */
> > > > > > > xenon_retune_setup(host);
> > > > > > >
> > > > > > > - xenon_set_acg(host, true);
> > > > > > > + /*
> > > > > > > + * The ACG should be turned off at the early init time, in order
> > > > > > > + * to solve a possile issues with the 1.8V regulator stabilization.
> > > > > > > + * The feature is enabled in later stage.
> > > > > > > + */
> > > > > > > + xenon_set_acg(host, false);
> > > > > > >
> > > > > > > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> > > > > > >
> > > > > > > --
> > > > > > > 2.29.0
> > > > > > >
Hi Pali,
Thanks for testing!
pt., 18 mar 2022 o 14:06 Pali Rohár <[email protected]> napisał(a):
>
> On Friday 18 March 2022 14:01:00 Pali Rohár wrote:
> > On Wednesday 16 March 2022 02:03:35 Marcin Wojtas wrote:
> > > Hi Pali,
> > >
> > > śr., 16 mar 2022 o 00:03 Pali Rohár <[email protected]> napisał(a):
> > > >
> > > > Hello!
> > > >
> > > > On Monday 14 March 2022 16:51:25 Marcin Wojtas wrote:
> > > > > Hi Pali,
> > > > >
> > > > >
> > > > > pon., 14 mar 2022 o 16:40 Pali Rohár <[email protected]> napisał(a):
> > > > > >
> > > > > > On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> > > > > > > On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> > > > > > > >
> > > > > > > > From: Alex Leibovich <[email protected]>
> > > > > > > >
> > > > > > > > Automatic Clock Gating is a feature used for the power
> > > > > > > > consumption optimisation. It turned out that
> > > > > > > > during early init phase it may prevent the stable voltage
> > > > > > > > switch to 1.8V - due to that on some platfroms an endless
> > > > > > > > printout in dmesg can be observed:
> > > > > > > > "mmc1: 1.8V regulator output did not became stable"
> > > > > > > > Fix the problem by disabling the ACG at very beginning
> > > > > > > > of the sdhci_init and let that be enabled later.
> > > > > > > >
> > > > > > > > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > > > > > > > Signed-off-by: Alex Leibovich <[email protected]>
> > > > > > > > Signed-off-by: Marcin Wojtas <[email protected]>
> > > > > > > > Cc: [email protected]
> > > > > > >
> > > > > > > Applied for fixes (by fixing the typos), thanks!
> > > > > >
> > > > > > Hello!
> > > > > >
> > > > > > Is not this patch address same issue which was fixed by patch which was
> > > > > > merged earlier?
> > > > > >
> > > > > > bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
> > > > > > https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
> > > > > >
> > > > >
> > > > > This indeed look similar. This fix was originally developed for CN913x
> > > > > platform without the mentioned patch (I'm wondering if it would also
> > > > > suffice to fix A3k board's problem). Anyway, I don't think we have an
> > > > > issue here, as everything seems to work fine on top of mainline Linux
> > > > > with both changes.
> > > >
> > > > Yea, there should be no issue. Just question is if we need _both_ fixes.
> > > >
> > > > I could probably try to revert bb32e1987bc5 and check what happens on
> > > > A3k board.
> > > >
> > >
> > > Yes, that would be interesting. Please let me know whenever you find
> > > time to check.
> >
> > Hello! Now I tested kernel with reverted commit bb32e1987bc5 ("mmc:
> > sdhci-xenon: fix annoying 1.8V regulator warning") and issue is still
> > fixed. I reverted also bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying
> > 1.8V regulator warning") commit and then issue appeared again.
>
> I mean that I reverted also 1a3ed0dc3594 ("mmc: sdhci-xenon: fix 1.8v
> regulator stabilization") commit and then issue appeared again.
>
> > So any of this commit is fixing that issue on Armada 3720.
> >
I think both can stay, but if I had to choose, I'd keep 1a3ed0dc3594
("mmc: sdhci-xenon: fix 1.8v regulator stabilization"):
* Now we know for sure it fixes both Armada 3720 and CN913x/Armada 7k8k
* Afaik this patch was checked with HW team (and IMO it looks a bit
less hacky than the extra read :) ).
Best regards,
Marcin
> > Should we revert one of them?
> >
> > > Best regards,
> > > Marcin
> > >
> > > > > > >
> > > > > > >
> > > > > > > > ---
> > > > > > > > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > > > > > > > 1 file changed, 6 insertions(+), 1 deletion(-)
> > > > > > > >
> > > > > > > > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > > > > > > > index c67611fdaa8a..4b05f6fdefb4 100644
> > > > > > > > --- a/drivers/mmc/host/sdhci-xenon.c
> > > > > > > > +++ b/drivers/mmc/host/sdhci-xenon.c
> > > > > > > > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > > > > > > > /* Disable tuning request and auto-retuning again */
> > > > > > > > xenon_retune_setup(host);
> > > > > > > >
> > > > > > > > - xenon_set_acg(host, true);
> > > > > > > > + /*
> > > > > > > > + * The ACG should be turned off at the early init time, in order
> > > > > > > > + * to solve a possile issues with the 1.8V regulator stabilization.
> > > > > > > > + * The feature is enabled in later stage.
> > > > > > > > + */
> > > > > > > > + xenon_set_acg(host, false);
> > > > > > > >
> > > > > > > > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> > > > > > > >
> > > > > > > > --
> > > > > > > > 2.29.0
> > > > > > > >
On Wednesday 16 March 2022 02:03:35 Marcin Wojtas wrote:
> Hi Pali,
>
> śr., 16 mar 2022 o 00:03 Pali Rohár <[email protected]> napisał(a):
> >
> > Hello!
> >
> > On Monday 14 March 2022 16:51:25 Marcin Wojtas wrote:
> > > Hi Pali,
> > >
> > >
> > > pon., 14 mar 2022 o 16:40 Pali Rohár <[email protected]> napisał(a):
> > > >
> > > > On Monday 11 January 2021 19:06:24 Ulf Hansson wrote:
> > > > > On Fri, 11 Dec 2020 at 15:17, Marcin Wojtas <[email protected]> wrote:
> > > > > >
> > > > > > From: Alex Leibovich <[email protected]>
> > > > > >
> > > > > > Automatic Clock Gating is a feature used for the power
> > > > > > consumption optimisation. It turned out that
> > > > > > during early init phase it may prevent the stable voltage
> > > > > > switch to 1.8V - due to that on some platfroms an endless
> > > > > > printout in dmesg can be observed:
> > > > > > "mmc1: 1.8V regulator output did not became stable"
> > > > > > Fix the problem by disabling the ACG at very beginning
> > > > > > of the sdhci_init and let that be enabled later.
> > > > > >
> > > > > > Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
> > > > > > Signed-off-by: Alex Leibovich <[email protected]>
> > > > > > Signed-off-by: Marcin Wojtas <[email protected]>
> > > > > > Cc: [email protected]
> > > > >
> > > > > Applied for fixes (by fixing the typos), thanks!
> > > >
> > > > Hello!
> > > >
> > > > Is not this patch address same issue which was fixed by patch which was
> > > > merged earlier?
> > > >
> > > > bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning")
> > > > https://lore.kernel.org/linux-mmc/CAPDyKFqAsvgAjfL-c9ukFNWeGJmufQosR2Eg9SKjXMVpNitdkA@mail.gmail.com/
> > > >
> > >
> > > This indeed look similar. This fix was originally developed for CN913x
> > > platform without the mentioned patch (I'm wondering if it would also
> > > suffice to fix A3k board's problem). Anyway, I don't think we have an
> > > issue here, as everything seems to work fine on top of mainline Linux
> > > with both changes.
> >
> > Yea, there should be no issue. Just question is if we need _both_ fixes.
> >
> > I could probably try to revert bb32e1987bc5 and check what happens on
> > A3k board.
> >
>
> Yes, that would be interesting. Please let me know whenever you find
> time to check.
Hello! Now I tested kernel with reverted commit bb32e1987bc5 ("mmc:
sdhci-xenon: fix annoying 1.8V regulator warning") and issue is still
fixed. I reverted also bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying
1.8V regulator warning") commit and then issue appeared again.
So any of this commit is fixing that issue on Armada 3720.
Should we revert one of them?
> Best regards,
> Marcin
>
> > > > >
> > > > >
> > > > > > ---
> > > > > > drivers/mmc/host/sdhci-xenon.c | 7 ++++++-
> > > > > > 1 file changed, 6 insertions(+), 1 deletion(-)
> > > > > >
> > > > > > diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
> > > > > > index c67611fdaa8a..4b05f6fdefb4 100644
> > > > > > --- a/drivers/mmc/host/sdhci-xenon.c
> > > > > > +++ b/drivers/mmc/host/sdhci-xenon.c
> > > > > > @@ -168,7 +168,12 @@ static void xenon_reset_exit(struct sdhci_host *host,
> > > > > > /* Disable tuning request and auto-retuning again */
> > > > > > xenon_retune_setup(host);
> > > > > >
> > > > > > - xenon_set_acg(host, true);
> > > > > > + /*
> > > > > > + * The ACG should be turned off at the early init time, in order
> > > > > > + * to solve a possile issues with the 1.8V regulator stabilization.
> > > > > > + * The feature is enabled in later stage.
> > > > > > + */
> > > > > > + xenon_set_acg(host, false);
> > > > > >
> > > > > > xenon_set_sdclk_off_idle(host, sdhc_id, false);
> > > > > >
> > > > > > --
> > > > > > 2.29.0
> > > > > >