This patch introduce devicetree for MSM8976 SoC,
most of already supported hardware should be described there.
Note about v2:
Based on advice from Bjorn i decided to keep clocks container,
this format appears in every other qcom dts.
Changes since v1
================
1. Dropped l1 i/d cache from cpu nodes.
2. Replaced xo_board with rpmcc where possible.
3. Added base address to memory node.
4. Padded addresses to 8 digits.
5. Moved imem to mmio range.
6. Adjusted mdss te pin name.
7. Reorganized reg positions per Konrad's request.
Adam Skladowski (1):
arm64: dts: qcom: Add MSM8976 device tree
arch/arm64/boot/dts/qcom/msm8976.dtsi | 1310 +++++++++++++++++++++++++
1 file changed, 1310 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8976.dtsi
--
2.25.1
Add a base DT for MSM8976 SoC.
Signed-off-by: Adam Skladowski <[email protected]>
---
arch/arm64/boot/dts/qcom/msm8976.dtsi | 1310 +++++++++++++++++++++++++
1 file changed, 1310 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8976.dtsi
diff --git a/arch/arm64/boot/dts/qcom/msm8976.dtsi b/arch/arm64/boot/dts/qcom/msm8976.dtsi
new file mode 100644
index 0000000000000..c073f16faa7ee
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8976.dtsi
@@ -0,0 +1,1310 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
+
+#include <dt-bindings/clock/qcom,gcc-msm8976.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen { };
+
+ clocks {
+ xo_board_clk: xo_board_clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <19200000>;
+ };
+
+ sleep_clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ };
+
+ CPU2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ };
+
+ CPU3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ };
+
+ CPU4: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x100>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1830>;
+ next-level-cache = <&L2_1>;
+ #cooling-cells = <2>;
+ };
+
+ CPU5: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x101>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1830>;
+ next-level-cache = <&L2_1>;
+ #cooling-cells = <2>;
+ };
+
+ CPU6: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x102>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1830>;
+ next-level-cache = <&L2_1>;
+ #cooling-cells = <2>;
+ };
+
+ CPU7: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x103>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1830>;
+ next-level-cache = <&L2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+ core1 {
+ cpu = <&CPU1>;
+ };
+ core2 {
+ cpu = <&CPU2>;
+ };
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU4>;
+ };
+ core1 {
+ cpu = <&CPU5>;
+ };
+ core2 {
+ cpu = <&CPU6>;
+ };
+ core3 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+
+ L2_0: l2-cache_0 {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+
+ L2_1: l2-cache_1 {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-msm8976", "qcom,scm";
+ clocks = <&gcc GCC_CRYPTO_CLK>,
+ <&gcc GCC_CRYPTO_AXI_CLK>,
+ <&gcc GCC_CRYPTO_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ #reset-cells = <1>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the reg */
+ reg = <0 0x80000000 0 0>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ cont_splash_mem: memory@83000000 {
+ reg = <0x0 0x83000000 0x0 0x2800000>;
+ };
+
+ ext_region: memory@85b00000 {
+ reg = <0x0 0x85b00000 0x0 0x500000>;
+ no-map;
+ };
+
+ smem_mem: memory@86300000 {
+ compatible = "qcom,smem";
+ reg = <0x0 0x86300000 0x0 0x100000>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ hwlocks = <&tcsr_mutex 3>;
+ no-map;
+ };
+
+ memory@86400000 {
+ reg = <0x0 0x86400000 0x0 0x800000>;
+ no-map;
+ };
+
+ mpss_mem: memory@86c00000 {
+ reg = <0x0 0x86c00000 0x0 0x5600000>;
+ no-map;
+ };
+
+ adsp_fw_mem: memory@8c200000 {
+ reg = <0x0 0x8c200000 0x0 0x1000000>;
+ no-map;
+ };
+
+ wcnss_fw_mem: memory@8d200000 {
+ reg = <0x0 0x8d200000 0x0 0x2600000>;
+ no-map;
+ };
+
+ venus_mem: memory@8f800000 {
+ reg = <0x0 0x8f800000 0x0 0x500000>;
+ no-map;
+ };
+
+ memory@d5700000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0xd5700000 0x0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ };
+
+ mba_mem: mba_mem@d5a00000 {
+ reg = <0x0 0xd5a00000 0x0 0x100000>;
+ no-map;
+ };
+ };
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests: rpm-requests {
+ compatible = "qcom,rpm-msm8976";
+ qcom,smd-channels = "rpm_requests";
+
+ rpmcc: rpmcc {
+ compatible = "qcom,rpmcc-msm8976", "qcom,rpmcc";
+ clocks = <&xo_board_clk>;
+ clock-names = "xo";
+ #clock-cells = <1>;
+ };
+
+ rpmpd: power-controller {
+ compatible = "qcom,msm8976-rpmpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmpd_opp_table>;
+
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "ref";
+
+ rpmpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmpd_opp_ret: opp1 {
+ opp-level = <RPM_SMD_LEVEL_RETENTION>;
+ };
+
+ rpmpd_opp_ret_plus: opp2 {
+ opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
+ };
+
+ rpmpd_opp_min_svs: opp3 {
+ opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+ };
+
+ rpmpd_opp_low_svs: opp4 {
+ opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+ };
+
+ rpmpd_opp_svs: opp5 {
+ opp-level = <RPM_SMD_LEVEL_SVS>;
+ };
+
+ rpmpd_opp_svs_plus: opp6 {
+ opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+ };
+
+ rpmpd_opp_nom: opp7 {
+ opp-level = <RPM_SMD_LEVEL_NOM>;
+ };
+
+ rpmpd_opp_nom_plus: opp8 {
+ opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+ };
+
+ rpmpd_opp_turbo: opp9 {
+ opp-level = <RPM_SMD_LEVEL_TURBO>;
+ };
+ };
+ };
+ };
+ };
+ };
+
+ smsm {
+ compatible = "qcom,smsm";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qcom,ipc-1 = <&apcs 8 13>;
+ qcom,ipc-3 = <&apcs 8 19>;
+
+ apps_smsm: apps@0 {
+ reg = <0>;
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smsm: hexagon@1 {
+ reg = <1>;
+ interrupts = <GIC_SPI 290 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wcnss_smsm: wcnss@6 {
+ reg = <6>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+
+ interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs 10>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ smp2p_adsp_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_adsp_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-modem {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ modem_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ modem_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-wcnss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <451>, <431>;
+
+ interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 18>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <4>;
+
+ wcnss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ wcnss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ soc: soc@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+ compatible = "simple-bus";
+
+ rng@22000 {
+ compatible = "qcom,prng";
+ reg = <0x00022000 0x1000>;
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "core";
+ };
+
+ rpm_msg_ram: sram@60000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0x00060000 0x8000>;
+ };
+
+ qfprom@a4000 {
+ compatible = "qcom,qfprom";
+ reg = <0x000a4000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tsens_caldata: caldata@218 {
+ reg = <0x218 0x18>;
+ };
+ };
+
+ tsens0: thermal-sensor@4a9000 {
+ compatible = "qcom,msm8976-tsens", "qcom,tsens-v1";
+ reg = <0x004a9000 0x1000>, /* TM */
+ <0x004a8000 0x1000>; /* SROT */
+ #qcom,sensors = <11>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow";
+ nvmem-cells = <&tsens_caldata>;
+ nvmem-cell-names = "calib";
+ #thermal-sensor-cells = <1>;
+ };
+
+ restart@4ab000 {
+ compatible = "qcom,pshold";
+ reg = <0x004ab000 0x4>;
+ };
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,msm8976-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ gpio-ranges = <&tlmm 0 0 158>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ mdss_te_default: mdss-te-default-state {
+ pins = "gpio24";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ sdc1_clk_on: sdc1-clk-on-state {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ sdc1_clk_off: sdc1-clk-off-state {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ sdc1_cmd_on: sdc1-cmd-on-state {
+ pins = "sdc1_cmd";
+ bias-disable;
+ drive-strength = <10>;
+ };
+
+ sdc1_cmd_off: sdc1-cmd-off-state {
+ pins = "sdc1_cmd";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ sdc1_data_on: sdc1-data-on-state {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sdc1_data_off: sdc1-data-off-state {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ sdc1_rclk_on: sdc1-rclk-on-state {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+
+ sdc1_rclk_off: sdc1-rclk-off-state {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+
+ sdc2_clk_on: sdc2-clk-on-state {
+ pins = "sdc2_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ sdc2_clk_off: sdc2-clk-off-state {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ sdc2_cmd_on: sdc2-cmd-on-state {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sdc2_cmd_off: sdc2-cmd-off-state {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ sdc2_data_on: sdc2-data-on-state {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sdc2_data_off: sdc2-data-off-state {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ sdc2_cd_on: cd-on-state {
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ sdc2_cd_off: cd-off-state {
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ gpio_key_default: gpio-key-default-state {
+ pins = "gpio113";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ i2c_1_default: i2c-1-default-state {
+ pins = "gpio2", "gpio3";
+ function = "blsp_i2c1";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_1_sleep: i2c-1-sleep-state {
+ pins = "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_2_default: i2c-2-default-state {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_2_sleep: i2c-2-sleep-state {
+ pins = "gpio6", "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_3_default: i2c-3-default-state {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c3";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_3_sleep: i2c-3-sleep-state {
+ pins = "gpio10", "gpio11";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_4_default: i2c-4-default-state {
+ pins = "gpio14", "gpio15";
+ function = "blsp_i2c4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_4_sleep: i2c-4-sleep-state {
+ pins = "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_5_default: i2c-5-default-state {
+ pins = "gpio136", "gpio137";
+ function = "blsp_i2c5";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_5_sleep: i2c-5-sleep-state {
+ pins = "gpio136", "gpio137";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_6_default: i2c-6-default-state {
+ pins = "gpio22", "gpio23";
+ function = "blsp_i2c6";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_6_sleep: i2c-6-sleep-state {
+ pins = "gpio22", "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_7_default: i2c-7-default-state {
+ pins = "gpio110", "gpio111";
+ function = "blsp_i2c7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_7_sleep: i2c-7-sleep-state {
+ pins = "gpio110", "gpio111";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_8_default: i2c-8-default-state {
+ pins = "gpio18", "gpio19";
+ function = "blsp_i2c8";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c_8_sleep: i2c-8-sleep-state {
+ pins = "gpio18", "gpio19";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ gcc: clock-controller@1800000 {
+ compatible = "qcom,gcc-msm8976-v1.1";
+ reg = <0x01800000 0x80000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+ <&rpmcc RPM_SMD_XO_A_CLK_SRC>,
+ <&dsi0_phy 1>,
+ <&dsi0_phy 0>,
+ <&dsi1_phy 1>,
+ <&dsi1_phy 0>;
+ clock-names = "xo",
+ "xo_a",
+ "dsi0pll",
+ "dsi0pllbyte",
+ "dsi1pll",
+ "dsi1pllbyte";
+ };
+
+ tcsr_mutex: hwlock@1905000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x01905000 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ tcsr: syscon@1937000 {
+ compatible = "qcom,tcsr-msm8976", "syscon";
+ reg = <0x01937000 0x30000>;
+ };
+
+ mdss: mdss@1a00000 {
+ compatible = "qcom,mdss";
+
+ reg = <0x01a00000 0x1000>,
+ <0x01ab0000 0x1040>;
+ reg-names = "mdss_phys",
+ "vbif_phys";
+
+ power-domains = <&gcc MDSS_GDSC>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>;
+ clock-names = "iface",
+ "bus",
+ "vsync",
+ "core";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ status = "disabled";
+
+ mdp: mdp@1a01000 {
+ compatible = "qcom,mdp5";
+ reg = <0x01a01000 0x89000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>,
+ <&gcc GCC_MDP_TBU_CLK>,
+ <&gcc GCC_MDP_RT_TBU_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync",
+ "tbu",
+ "tbu_rt";
+ iommus = <&apps_iommu 0x17>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdp5_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@1a94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0x01a94000 0x2d4>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ assigned-clocks = <&gcc GCC_MDSS_BYTE0_CLK_SRC>,
+ <&gcc GCC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi0_phy 0>,
+ <&dsi0_phy 1>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE0_CLK>,
+ <&gcc GCC_MDSS_PCLK0_CLK>,
+ <&gcc GCC_MDSS_ESC0_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core";
+
+ phys = <&dsi0_phy>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi0_phy: phy@1a94400 {
+ compatible = "qcom,dsi-phy-28nm-hpm-fam-b";
+ reg = <0x01a94400 0x20c>,
+ <0x01a94b80 0x2c>,
+ <0x01a94a00 0xd4>;
+ reg-names = "dsi_phy",
+ "dsi_phy_regulator",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ dsi1: dsi@1a96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0x01a96000 0x2d4>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ assigned-clocks = <&gcc GCC_MDSS_BYTE1_CLK_SRC>,
+ <&gcc GCC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&dsi1_phy 0>,
+ <&dsi1_phy 1>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE1_CLK>,
+ <&gcc GCC_MDSS_PCLK1_CLK>,
+ <&gcc GCC_MDSS_ESC1_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core";
+
+ phys = <&dsi1_phy>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi1_in: endpoint {
+ remote-endpoint = <&mdp5_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi1_phy: phy@1a96400 {
+ compatible = "qcom,dsi-phy-28nm-hpm-fam-b";
+ reg = <0x01a96400 0x20c>,
+ <0x01a96b80 0x2c>,
+ <0x01a96a00 0xd4>;
+ reg-names = "dsi_phy",
+ "dsi_phy_regulator",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+ };
+
+ apps_iommu: iommu@1e00000 {
+ compatible = "qcom,msm-iommu-v1";
+ ranges = <0 0x01e20000 0x20000>;
+
+ clocks = <&gcc GCC_SMMU_CFG_CLK>,
+ <&gcc GCC_APSS_TCU_CLK>;
+ clock-names = "iface", "bus";
+
+ qcom,iommu-secure-id = <17>;
+
+ #address-cells = <1>;
+ #iommu-cells = <1>;
+ #size-cells = <1>;
+
+ /* MDP_0 */
+ iommu-ctx@17000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x17000 0x1000>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ spmi_bus: spmi@200f000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0200f000 0x1000>,
+ <0x02400000 0x800000>,
+ <0x02c00000 0x800000>,
+ <0x03800000 0x200000>,
+ <0x0200a000 0x2100>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ interrupt-controller;
+
+ #interrupt-cells = <4>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+
+ sdhc_1: mmc@7824900 {
+ compatible = "qcom,sdhci-msm-v4";
+
+ reg = <0x07824900 0x500>, <0x07824000 0x800>;
+ reg-names = "hc", "core";
+
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "core", "xo";
+
+ power-domains = <&rpmpd MSM8976_VDDCX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;
+
+ mmc-hs400-1_8v;
+ mmc-hs200-1_8v;
+ mmc-ddr-1_8v;
+ bus-width = <8>;
+ non-removable;
+
+ status = "disabled";
+
+ sdhc1_opp_table: opp-table-sdhc1 {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmpd_opp_svs>;
+ };
+
+ opp-186400000 {
+ opp-hz = /bits/ 64 <186400000>;
+ required-opps = <&rpmpd_opp_nom>;
+ };
+
+ opp-372800000 {
+ opp-hz = /bits/ 64 <372800000>;
+ required-opps = <&rpmpd_opp_nom>;
+ };
+ };
+ };
+
+ sdhc_2: mmc@7864900 {
+ compatible = "qcom,sdhci-msm-v4";
+
+ reg = <0x07864900 0x500>, <0x07864000 0x800>;
+ reg-names = "hc", "core";
+
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "core", "xo";
+
+ power-domains = <&rpmpd MSM8976_VDDCX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+
+ bus-width = <4>;
+
+ status = "disabled";
+
+ sdhc2_opp_table: opp-table-sdhc2 {
+ compatible = "operating-points-v2";
+
+ opp-50000000 {
+ opp-hz = /bits/ 64 <50000000>;
+ required-opps = <&rpmpd_opp_svs>;
+ };
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmpd_opp_nom>;
+ };
+ };
+ };
+
+ i2c_1: i2c@78b5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_1_default>;
+ pinctrl-1 = <&i2c_1_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_2: i2c@78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_2_default>;
+ pinctrl-1 = <&i2c_2_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_3: i2c@78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_3_default>;
+ pinctrl-1 = <&i2c_3_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_4: i2c@78b8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_4_default>;
+ pinctrl-1 = <&i2c_4_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_5: i2c@7af5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07af5000 0x600>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_5_default>;
+ pinctrl-1 = <&i2c_5_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_6: i2c@7af6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07af6000 0x600>;
+ interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_6_default>;
+ pinctrl-1 = <&i2c_6_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_7: i2c@7af7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07af7000 0x600>;
+ interrupts = <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_7_default>;
+ pinctrl-1 = <&i2c_7_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ i2c_8: i2c@7af8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07af8000 0x600>;
+ interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "iface";
+ clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c_8_default>;
+ pinctrl-1 = <&i2c_8_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ sram@8600000 {
+ compatible = "qcom,msm8976-imem", "syscon", "simple-mfd";
+ reg = <0x08600000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0 0x08600000 0x1000>;
+
+ pil-reloc@94c {
+ compatible = "qcom,pil-reloc-info";
+ reg = <0x94c 0xc8>;
+ };
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ apcs: mailbox@b011000 {
+ compatible = "qcom,msm8976-apcs-kpss-global", "syscon";
+ reg = <0x0b011000 0x1000>;
+ #mbox-cells = <1>;
+ };
+
+ timer@b120000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b120000 0x1000>;
+ #address-cells = <0x01>;
+ #size-cells = <0x01>;
+ ranges;
+
+ frame@b121000 {
+ reg = <0x0b121000 0x1000>,
+ <0x0b122000 0x1000>;
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ frame@b123000 {
+ reg = <0x0b123000 0x1000>;
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b124000 {
+ reg = <0x0b124000 0x1000>;
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b125000 {
+ reg = <0x0b125000 0x1000>;
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b126000 {
+ reg = <0x0b126000 0x1000>;
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b127000 {
+ reg = <0x0b127000 0x1000>;
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b128000 {
+ reg = <0x0b128000 0x1000>;
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
--
2.25.1
On Tue, Nov 01, 2022 at 08:16:20PM +0100, Adam Skladowski wrote:
> Add a base DT for MSM8976 SoC.
>
Please send this together with some device dts, so that it's actually
being built.
> Signed-off-by: Adam Skladowski <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/msm8976.dtsi | 1310 +++++++++++++++++++++++++
> 1 file changed, 1310 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8976.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8976.dtsi b/arch/arm64/boot/dts/qcom/msm8976.dtsi
> new file mode 100644
> index 0000000000000..c073f16faa7ee
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8976.dtsi
> @@ -0,0 +1,1310 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8976.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen { };
> +
> + clocks {
> + xo_board_clk: xo_board_clk {
No underscore in node names please (xo-board-clk sounds good).
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <19200000>;
> + };
> +
> + sleep_clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + };
> + };
> +
[..]
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + cont_splash_mem: memory@83000000 {
"memory" is reserved, so please don't do what we've been doing
everywhere else, but instead use descriptive names.
> + reg = <0x0 0x83000000 0x0 0x2800000>;
> + };
> +
[..]
> +
> + mba_mem: mba_mem@d5a00000 {
No underscores in node names please.
> + reg = <0x0 0xd5a00000 0x0 0x100000>;
> + no-map;
> + };
> + };
[..]
> + soc: soc@0 {
[..]
> +
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,msm8976-pinctrl";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + gpio-ranges = <&tlmm 0 0 158>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + mdss_te_default: mdss-te-default-state {
> + pins = "gpio24";
> + function = "mdp_vsync";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + sdc1_clk_on: sdc1-clk-on-state {
I do like when related configuration is lumped together in a single
state:
sdc1-default-state {
clk-pins {
...;
};
cmd-pins {
...;
};
...
};
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + sdc1_clk_off: sdc1-clk-off-state {
> + pins = "sdc1_clk";
> + bias-disable;
> + drive-strength = <2>;
> + };
> +
[..]
> +
> + gpio_key_default: gpio-key-default-state {
This looks like a state that should go in the board-specific .dts.
> + pins = "gpio113";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
[..]
> + };
> +
> + gcc: clock-controller@1800000 {
> + compatible = "qcom,gcc-msm8976-v1.1";
> + reg = <0x01800000 0x80000>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
> + <&rpmcc RPM_SMD_XO_A_CLK_SRC>,
> + <&dsi0_phy 1>,
> + <&dsi0_phy 0>,
> + <&dsi1_phy 1>,
> + <&dsi1_phy 0>;
> + clock-names = "xo",
> + "xo_a",
> + "dsi0pll",
> + "dsi0pllbyte",
> + "dsi1pll",
> + "dsi1pllbyte";
> + };
> +
> + tcsr_mutex: hwlock@1905000 {
> + compatible = "qcom,tcsr-mutex";
> + reg = <0x01905000 0x20000>;
> + #hwlock-cells = <1>;
> + };
> +
> + tcsr: syscon@1937000 {
> + compatible = "qcom,tcsr-msm8976", "syscon";
> + reg = <0x01937000 0x30000>;
> + };
> +
> + mdss: mdss@1a00000 {
display-subsystem@ please.
> + compatible = "qcom,mdss";
> +
> + reg = <0x01a00000 0x1000>,
> + <0x01ab0000 0x1040>;
> + reg-names = "mdss_phys",
> + "vbif_phys";
> +
> + power-domains = <&gcc MDSS_GDSC>;
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>;
> + clock-names = "iface",
> + "bus",
> + "vsync",
> + "core";
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdp: mdp@1a01000 {
display-controller@ please
> + compatible = "qcom,mdp5";
> + reg = <0x01a01000 0x89000>;
> + reg-names = "mdp_phys";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>,
> + <&gcc GCC_MDP_TBU_CLK>,
> + <&gcc GCC_MDP_RT_TBU_CLK>;
> + clock-names = "iface",
> + "bus",
> + "core",
> + "vsync",
> + "tbu",
> + "tbu_rt";
> + iommus = <&apps_iommu 0x17>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdp5_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + mdp5_intf2_out: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> +
> + dsi0: dsi@1a94000 {
If you label this mdss_dsi0 (and similar for other mdss nodes) it will
sort nicely in the dts
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0x01a94000 0x2d4>;
> + reg-names = "dsi_ctrl";
[..]
Generally, please try to use make dtbs_check
Thanks,
Bjorn
On 01/11/2022 15:16, Adam Skladowski wrote:
> Add a base DT for MSM8976 SoC.
>
> Signed-off-by: Adam Skladowski <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/msm8976.dtsi | 1310 +++++++++++++++++++++++++
> 1 file changed, 1310 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8976.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8976.dtsi b/arch/arm64/boot/dts/qcom/msm8976.dtsi
> new file mode 100644
> index 0000000000000..c073f16faa7ee
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8976.dtsi
> @@ -0,0 +1,1310 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8976.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen { };
> +
> + clocks {
> + xo_board_clk: xo_board_clk {
No underscores in node names.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <19200000>;
> + };
> +
> + sleep_clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + };
> + };
> +
(...)
> +
> + tcsr_mutex: hwlock@1905000 {
> + compatible = "qcom,tcsr-mutex";
> + reg = <0x01905000 0x20000>;
> + #hwlock-cells = <1>;
> + };
> +
> + tcsr: syscon@1937000 {
> + compatible = "qcom,tcsr-msm8976", "syscon";
Where is the documentation?
> + reg = <0x01937000 0x30000>;
> + };
> +
> + mdss: mdss@1a00000 {
> + compatible = "qcom,mdss";
> +
> + reg = <0x01a00000 0x1000>,
> + <0x01ab0000 0x1040>;
> + reg-names = "mdss_phys",
> + "vbif_phys";
> +
> + power-domains = <&gcc MDSS_GDSC>;
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>;
> + clock-names = "iface",
> + "bus",
> + "vsync",
> + "core";
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdp: mdp@1a01000 {
I think other DTSes use different node name...
> + compatible = "qcom,mdp5";
> + reg = <0x01a01000 0x89000>;
> + reg-names = "mdp_phys";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>,
> + <&gcc GCC_MDP_TBU_CLK>,
> + <&gcc GCC_MDP_RT_TBU_CLK>;
> + clock-names = "iface",
> + "bus",
> + "core",
> + "vsync",
> + "tbu",
> + "tbu_rt";
> + iommus = <&apps_iommu 0x17>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdp5_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + mdp5_intf2_out: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> +
> + dsi0: dsi@1a94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0x01a94000 0x2d4>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4>;
> +
> + assigned-clocks = <&gcc GCC_MDSS_BYTE0_CLK_SRC>,
> + <&gcc GCC_MDSS_PCLK0_CLK_SRC>;
> + assigned-clock-parents = <&dsi0_phy 0>,
> + <&dsi0_phy 1>;
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE0_CLK>,
> + <&gcc GCC_MDSS_PCLK0_CLK>,
> + <&gcc GCC_MDSS_ESC0_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> +
> + phys = <&dsi0_phy>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&mdp5_intf1_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi0_phy: phy@1a94400 {
> + compatible = "qcom,dsi-phy-28nm-hpm-fam-b";
> + reg = <0x01a94400 0x20c>,
> + <0x01a94b80 0x2c>,
> + <0x01a94a00 0xd4>;
> + reg-names = "dsi_phy",
> + "dsi_phy_regulator",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "iface", "ref";
> +
> + status = "disabled";
> + };
> +
> + dsi1: dsi@1a96000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0x01a96000 0x2d4>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <5>;
> +
> + assigned-clocks = <&gcc GCC_MDSS_BYTE1_CLK_SRC>,
> + <&gcc GCC_MDSS_PCLK1_CLK_SRC>;
> + assigned-clock-parents = <&dsi1_phy 0>,
> + <&dsi1_phy 1>;
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE1_CLK>,
> + <&gcc GCC_MDSS_PCLK1_CLK>,
> + <&gcc GCC_MDSS_ESC1_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> +
> + phys = <&dsi1_phy>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi1_in: endpoint {
> + remote-endpoint = <&mdp5_intf2_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dsi1_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi1_phy: phy@1a96400 {
> + compatible = "qcom,dsi-phy-28nm-hpm-fam-b";
> + reg = <0x01a96400 0x20c>,
> + <0x01a96b80 0x2c>,
> + <0x01a96a00 0xd4>;
> + reg-names = "dsi_phy",
> + "dsi_phy_regulator",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "iface", "ref";
> +
> + status = "disabled";
> + };
> + };
> +
> + apps_iommu: iommu@1e00000 {
> + compatible = "qcom,msm-iommu-v1";
> + ranges = <0 0x01e20000 0x20000>;
> +
> + clocks = <&gcc GCC_SMMU_CFG_CLK>,
> + <&gcc GCC_APSS_TCU_CLK>;
> + clock-names = "iface", "bus";
> +
> + qcom,iommu-secure-id = <17>;
> +
> + #address-cells = <1>;
> + #iommu-cells = <1>;
> + #size-cells = <1>;
> +
> + /* MDP_0 */
> + iommu-ctx@17000 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x17000 0x1000>;
> + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + spmi_bus: spmi@200f000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0200f000 0x1000>,
> + <0x02400000 0x800000>,
> + <0x02c00000 0x800000>,
> + <0x03800000 0x200000>,
> + <0x0200a000 0x2100>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + interrupt-controller;
> +
> + #interrupt-cells = <4>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> +
> + sdhc_1: mmc@7824900 {
> + compatible = "qcom,sdhci-msm-v4";
> +
> + reg = <0x07824900 0x500>, <0x07824000 0x800>;
> + reg-names = "hc", "core";
> +
> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hc_irq", "pwr_irq";
> +
> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> + <&gcc GCC_SDCC1_APPS_CLK>,
> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "iface", "core", "xo";
> +
> + power-domains = <&rpmpd MSM8976_VDDCX>;
> + operating-points-v2 = <&sdhc1_opp_table>;
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
> + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;
> +
> + mmc-hs400-1_8v;
> + mmc-hs200-1_8v;
> + mmc-ddr-1_8v;
> + bus-width = <8>;
> + non-removable;
> +
> + status = "disabled";
> +
> + sdhc1_opp_table: opp-table-sdhc1 {
Did you test the DTS with dtbs_check?
Best regards,
Krzysztof
On 01/11/2022 15:16, Adam Skladowski wrote:
> Add a base DT for MSM8976 SoC.
>
> Signed-off-by: Adam Skladowski <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/msm8976.dtsi | 1310 +++++++++++++++++++++++++
> 1 file changed, 1310 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8976.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8976.dtsi b/arch/arm64/boot/dts/qcom/msm8976.dtsi
> new file mode 100644
> index 0000000000000..c073f16faa7ee
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8976.dtsi
> @@ -0,0 +1,1310 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8976.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen { };
> +
> + clocks {
You missed here Rob's feedback.
> + xo_board_clk: xo_board_clk {
And for some reason this got worse from v1...
Best regards,
Krzysztof