1) add a flag to identify new geneeration Intel controllers
2) define *setup* and hook it up for new genertion Intel controllers
3) map Typhoon Peak controller (PID:0x0032) to new generation controller
Signed-off-by: Kiran K <[email protected]>
Signed-off-by: Amit K Bag <[email protected]>
Signed-off-by: Raghuram Hegde <[email protected]>
Reviewed-by: Sathish Narasimman <[email protected]>
Reviewed-by: Chethan T N <[email protected]>
Reviewed-by: Srivatsa Ravishankar <[email protected]>
---
Changes in v2:
- None
drivers/bluetooth/btusb.c | 145 +++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 142 insertions(+), 3 deletions(-)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index ab3d890..698ec95 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -59,6 +59,7 @@ static struct usb_driver btusb_driver;
#define BTUSB_MEDIATEK 0x200000
#define BTUSB_WIDEBAND_SPEECH 0x400000
#define BTUSB_VALID_LE_STATES 0x800000
+#define BTUSB_INTEL_NEWGEN 0x1000000
static const struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
@@ -360,7 +361,7 @@ static const struct usb_device_id blacklist_table[] = {
BTUSB_WIDEBAND_SPEECH },
{ USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
BTUSB_WIDEBAND_SPEECH },
- { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEW |
+ { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEWGEN |
BTUSB_WIDEBAND_SPEECH},
{ USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
{ USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
@@ -2871,6 +2872,138 @@ static int btusb_setup_intel_new(struct hci_dev *hdev)
return 0;
}
+static int btusb_setup_intel_newgen(struct hci_dev *hdev)
+{
+ struct btusb_data *data = hci_get_drvdata(hdev);
+ u32 boot_param;
+ char ddcname[64];
+ ktime_t calltime, delta, rettime;
+ unsigned long long duration;
+ int err;
+ struct intel_debug_features features;
+ struct intel_version_tlv version;
+
+ BT_DBG("%s", hdev->name);
+
+ /* Set the default boot parameter to 0x0 and it is updated to
+ * SKU specific boot parameter after reading Intel_Write_Boot_Params
+ * command while downloading the firmware.
+ */
+ boot_param = 0x00000000;
+
+ calltime = ktime_get();
+
+ /* Read the Intel version information to determine if the device
+ * is in bootloader mode or if it already has operational firmware
+ * loaded.
+ */
+ err = btintel_read_version_tlv(hdev, &version);
+ if (err) {
+ bt_dev_err(hdev, "Intel Read version failed (%d)", err);
+ btintel_reset_to_bootloader(hdev);
+ return err;
+ }
+
+ btintel_version_info_tlv(hdev, &version);
+
+ err = btusb_intel_download_firmware_newgen(hdev, &version, &boot_param);
+ if (err)
+ return err;
+
+ /* check if controller is already having an operational firmware */
+ if (version.img_type == 0x03)
+ goto finish;
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
+
+ calltime = ktime_get();
+
+ set_bit(BTUSB_BOOTING, &data->flags);
+
+ err = btintel_send_intel_reset(hdev, boot_param);
+ if (err) {
+ bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
+ btintel_reset_to_bootloader(hdev);
+ return err;
+ }
+
+ /* The bootloader will not indicate when the device is ready. This
+ * is done by the operational firmware sending bootup notification.
+ *
+ * Booting into operational firmware should not take longer than
+ * 1 second. However if that happens, then just fail the setup
+ * since something went wrong.
+ */
+ bt_dev_info(hdev, "Waiting for device to boot");
+
+ err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
+ TASK_INTERRUPTIBLE,
+ msecs_to_jiffies(1000));
+
+ if (err == -EINTR) {
+ bt_dev_err(hdev, "Device boot interrupted");
+ return -EINTR;
+ }
+
+ if (err) {
+ bt_dev_err(hdev, "Device boot timeout");
+ btintel_reset_to_bootloader(hdev);
+ return -ETIMEDOUT;
+ }
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Device booted in %llu usecs", duration);
+
+ clear_bit(BTUSB_BOOTLOADER, &data->flags);
+
+ err = btusb_setup_intel_newgen_get_fw_name(&version, ddcname,
+ sizeof(ddcname), "ddc");
+ if (!err) {
+ bt_dev_err(hdev, "Unsupported Intel firmware naming");
+ } else {
+ /* Once the device is running in operational mode, it needs to
+ * apply the device configuration (DDC) parameters.
+ *
+ * The device can work without DDC parameters, so even if it
+ * fails to load the file, no need to fail the setup.
+ */
+ btintel_load_ddc_config(hdev, ddcname);
+ }
+
+ /* Read the Intel supported features and if new exception formats
+ * supported, need to load the additional DDC config to enable.
+ */
+ btintel_read_debug_features(hdev, &features);
+
+ /* Set DDC mask for available debug features */
+ btintel_set_debug_features(hdev, &features);
+
+ /* Read the Intel version information after loading the FW */
+ err = btintel_read_version_tlv(hdev, &version);
+ if (err)
+ return err;
+
+ btintel_version_info_tlv(hdev, &version);
+
+finish:
+ /* Set the event mask for Intel specific vendor events. This enables
+ * a few extra events that are useful during general operation. It
+ * does not enable any debugging related events.
+ *
+ * The device will function correctly without these events enabled
+ * and thus no need to fail the setup.
+ */
+ btintel_set_event_mask(hdev, false);
+
+ return 0;
+}
static int btusb_shutdown_intel(struct hci_dev *hdev)
{
struct sk_buff *skb;
@@ -4119,7 +4252,8 @@ static int btusb_probe(struct usb_interface *intf,
init_usb_anchor(&data->ctrl_anchor);
spin_lock_init(&data->rxlock);
- if (id->driver_info & BTUSB_INTEL_NEW) {
+ if ((id->driver_info & BTUSB_INTEL_NEW) ||
+ (id->driver_info & BTUSB_INTEL_NEWGEN)) {
data->recv_event = btusb_recv_event_intel;
data->recv_bulk = btusb_recv_bulk_intel;
set_bit(BTUSB_BOOTLOADER, &data->flags);
@@ -4214,7 +4348,8 @@ static int btusb_probe(struct usb_interface *intf,
set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
}
- if (id->driver_info & BTUSB_INTEL_NEW) {
+ if ((id->driver_info & BTUSB_INTEL_NEW) ||
+ (id->driver_info & BTUSB_INTEL_NEWGEN)) {
hdev->manufacturer = 2;
hdev->send = btusb_send_frame_intel;
hdev->setup = btusb_setup_intel_new;
@@ -4228,6 +4363,10 @@ static int btusb_probe(struct usb_interface *intf,
set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
}
+ /* Overload only setup function for new generation Intel controllers */
+ if (id->driver_info & BTUSB_INTEL_NEWGEN)
+ hdev->setup = btusb_setup_intel_newgen;
+
if (id->driver_info & BTUSB_MARVELL)
hdev->set_bdaddr = btusb_set_bdaddr_marvell;
--
2.7.4