Dear Linux folks,
On the Dell XPS 13 9360 from 2016, BIOS 2.21.0 06/02/2022, with Debian
sid/unstable and Debian’s Linux 6.5.10 kernel, I am trying to extend the
run-time with battery, at under 50 % of it’s original capacity, and I am
using PowerTOP 2.15.
[ 0.000000] microcode: updated early: 0xf0 -> 0xf4, date =
2023-02-22
[ 0.000000] Linux version 6.5.0-4-amd64
([email protected]) (gcc-13 (Debian 13.2.0-6) 13.2.0, GNU
ld (GNU Binutils for Debian) 2.41) #1 SMP PREEMPT_DYNAMIC Debian
6.5.10-1 (2023-11-03)
[…]
[ 0.000000] DMI: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0
06/02/2022
[…]
[ 15.646414] usbcore: registered new interface driver btusb
[ 15.648188] ath10k_pci 0000:3a:00.0: pci irq msi oper_irq_mode 2
irq_mode 0 reset_mode 0
[ 15.649555] bluetooth hci0: firmware: direct-loading firmware
qca/rampatch_usb_00000302.bin
[ 15.650018] Bluetooth: hci0: using rampatch file:
qca/rampatch_usb_00000302.bin
[ 15.650020] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8,
firmware rome 0x302 build 0x111
Although radio/wireless devices are turned off in GNOME, PowerTOP shows
the Bluetooth device drawing 0.85 W of energy:
848 mW 100.0% Device USB device: usb-device-0cf3-e300
$ lsusb -d 0cf3:e300
Bus 001 Device 002: ID 0cf3:e300 Qualcomm Atheros Communications
QCA61x4 Bluetooth 4.0
$ lspci -nn -s 3a:00.0
3a:00.0 Network controller [0280]: Qualcomm Atheros QCA6174
802.11ac Wireless Network Adapter [168c:003e] (rev 32)
After unloading the module `btusb`, the entry disappears from the
PowerTOP list after a while.
usbcore: deregistering interface driver btusb
Auto-suspend was enabled for the device. (Though it shouldn’t have
mattered as it was disabled in GNOME?)
Anyways, have you heard of such an issue? Can I provide more
information, to get it to not use any energy while being disable in GNOME?
Kind regards,
Paul
```
$ lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v6/7th Gen
Core Processor Host Bridge/DRAM Registers [8086:5904] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics
620 [8086:5916] (rev 02)
00:04.0 Signal processing controller [1180]: Intel Corporation Xeon
E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem
[8086:1903] (rev 02)
00:14.0 USB controller [0c03]: Intel Corporation Sunrise Point-LP USB
3.0 xHCI Controller [8086:9d2f] (rev 21)
00:14.2 Signal processing controller [1180]: Intel Corporation Sunrise
Point-LP Thermal subsystem [8086:9d31] (rev 21)
00:15.0 Signal processing controller [1180]: Intel Corporation Sunrise
Point-LP Serial IO I2C Controller #0 [8086:9d60] (rev 21)
00:15.1 Signal processing controller [1180]: Intel Corporation Sunrise
Point-LP Serial IO I2C Controller #1 [8086:9d61] (rev 21)
00:16.0 Communication controller [0780]: Intel Corporation Sunrise
Point-LP CSME HECI #1 [8086:9d3a] (rev 21)
00:1c.0 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #1 [8086:9d10] (rev f1)
00:1c.4 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #5 [8086:9d14] (rev f1)
00:1c.5 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #6 [8086:9d15] (rev f1)
00:1d.0 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #9 [8086:9d18] (rev f1)
00:1f.0 ISA bridge [0601]: Intel Corporation Sunrise Point-LP LPC
Controller [8086:9d58] (rev 21)
00:1f.2 Memory controller [0580]: Intel Corporation Sunrise Point-LP PMC
[8086:9d21] (rev 21)
00:1f.3 Audio device [0403]: Intel Corporation Sunrise Point-LP HD Audio
[8086:9d71] (rev 21)
00:1f.4 SMBus [0c05]: Intel Corporation Sunrise Point-LP SMBus
[8086:9d23] (rev 21)
01:00.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
02:00.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
02:01.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
02:02.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
39:00.0 USB controller [0c03]: Intel Corporation DSL6340 USB 3.1
Controller [Alpine Ridge] [8086:15b5]
3a:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac
Wireless Network Adapter [168c:003e] (rev 32)
3b:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS525A
PCI Express Card Reader [10ec:525a] (rev 01)
3c:00.0 Non-Volatile memory controller [0108]: SK hynix PC300 NVMe Solid
State Drive 512GB [1c5c:1284]
$ lspci -t
-[0000:00]-+-00.0
+-02.0
+-04.0
+-14.0
+-14.2
+-15.0
+-15.1
+-16.0
+-1c.0-[01-39]----00.0-[02-39]--+-00.0-[03]--
| +-01.0-[04-38]--
| \-02.0-[39]----00.0
+-1c.4-[3a]----00.0
+-1c.5-[3b]----00.0
+-1d.0-[3c]----00.0
+-1f.0
+-1f.2
+-1f.3
\-1f.4
$ lsusb -t
/: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 10000M
|__ Port 2: Dev 3, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
|__ Port 1: Dev 3, If 0, Class=Human Interface Device,
Driver=usbhid, 12M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
|__ Port 3: Dev 2, If 0, Class=Wireless, Driver=, 12M
|__ Port 3: Dev 2, If 1, Class=Wireless, Driver=, 12M
|__ Port 4: Dev 3, If 0, Class=Human Interface Device,
Driver=usbhid, 12M
|__ Port 5: Dev 4, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 5: Dev 4, If 1, Class=Video, Driver=uvcvideo, 480M
```
[Fix typo in subject line]
Dear Linux folks,
On the Dell XPS 13 9360 from 2016, BIOS 2.21.0 06/02/2022, with Debian
sid/unstable and Debian’s Linux 6.5.10 kernel, I am trying to extend the
run-time with battery, at under 50 % of it’s original capacity, and I am
using PowerTOP 2.15.
[ 0.000000] microcode: updated early: 0xf0 -> 0xf4, date =
2023-02-22
[ 0.000000] Linux version 6.5.0-4-amd64
([email protected]) (gcc-13 (Debian 13.2.0-6) 13.2.0, GNU
ld (GNU Binutils for Debian) 2.41) #1 SMP PREEMPT_DYNAMIC Debian
6.5.10-1 (2023-11-03)
[…]
[ 0.000000] DMI: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0
06/02/2022
[…]
[ 15.646414] usbcore: registered new interface driver btusb
[ 15.648188] ath10k_pci 0000:3a:00.0: pci irq msi oper_irq_mode 2
irq_mode 0 reset_mode 0
[ 15.649555] bluetooth hci0: firmware: direct-loading firmware
qca/rampatch_usb_00000302.bin
[ 15.650018] Bluetooth: hci0: using rampatch file:
qca/rampatch_usb_00000302.bin
[ 15.650020] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8,
firmware rome 0x302 build 0x111
Although radio/wireless devices are turned off in GNOME, PowerTOP shows
the Bluetooth device drawing 0.85 W of energy:
848 mW 100.0% Device USB device: usb-device-0cf3-e300
$ lsusb -d 0cf3:e300
Bus 001 Device 002: ID 0cf3:e300 Qualcomm Atheros Communications
QCA61x4 Bluetooth 4.0
$ lspci -nn -s 3a:00.0
3a:00.0 Network controller [0280]: Qualcomm Atheros QCA6174
802.11ac Wireless Network Adapter [168c:003e] (rev 32)
After unloading the module `btusb`, the entry disappears from the
PowerTOP list after a while.
usbcore: deregistering interface driver btusb
Auto-suspend was enabled for the device. (Though it shouldn’t have
mattered as it was disabled in GNOME?)
Anyways, have you heard of such an issue? Can I provide more
information, to get it to not use any energy while being disable in GNOME?
Kind regards,
Paul
```
$ lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v6/7th Gen
Core Processor Host Bridge/DRAM Registers [8086:5904] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics
620 [8086:5916] (rev 02)
00:04.0 Signal processing controller [1180]: Intel Corporation Xeon
E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem
[8086:1903] (rev 02)
00:14.0 USB controller [0c03]: Intel Corporation Sunrise Point-LP USB
3.0 xHCI Controller [8086:9d2f] (rev 21)
00:14.2 Signal processing controller [1180]: Intel Corporation Sunrise
Point-LP Thermal subsystem [8086:9d31] (rev 21)
00:15.0 Signal processing controller [1180]: Intel Corporation Sunrise
Point-LP Serial IO I2C Controller #0 [8086:9d60] (rev 21)
00:15.1 Signal processing controller [1180]: Intel Corporation Sunrise
Point-LP Serial IO I2C Controller #1 [8086:9d61] (rev 21)
00:16.0 Communication controller [0780]: Intel Corporation Sunrise
Point-LP CSME HECI #1 [8086:9d3a] (rev 21)
00:1c.0 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #1 [8086:9d10] (rev f1)
00:1c.4 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #5 [8086:9d14] (rev f1)
00:1c.5 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #6 [8086:9d15] (rev f1)
00:1d.0 PCI bridge [0604]: Intel Corporation Sunrise Point-LP PCI
Express Root Port #9 [8086:9d18] (rev f1)
00:1f.0 ISA bridge [0601]: Intel Corporation Sunrise Point-LP LPC
Controller [8086:9d58] (rev 21)
00:1f.2 Memory controller [0580]: Intel Corporation Sunrise Point-LP PMC
[8086:9d21] (rev 21)
00:1f.3 Audio device [0403]: Intel Corporation Sunrise Point-LP HD Audio
[8086:9d71] (rev 21)
00:1f.4 SMBus [0c05]: Intel Corporation Sunrise Point-LP SMBus
[8086:9d23] (rev 21)
01:00.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
02:00.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
02:01.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
02:02.0 PCI bridge [0604]: Intel Corporation DSL6340 Thunderbolt 3
Bridge [Alpine Ridge 2C 2015] [8086:1576]
39:00.0 USB controller [0c03]: Intel Corporation DSL6340 USB 3.1
Controller [Alpine Ridge] [8086:15b5]
3a:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac
Wireless Network Adapter [168c:003e] (rev 32)
3b:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS525A
PCI Express Card Reader [10ec:525a] (rev 01)
3c:00.0 Non-Volatile memory controller [0108]: SK hynix PC300 NVMe Solid
State Drive 512GB [1c5c:1284]
$ lspci -t
-[0000:00]-+-00.0
+-02.0
+-04.0
+-14.0
+-14.2
+-15.0
+-15.1
+-16.0
+-1c.0-[01-39]----00.0-[02-39]--+-00.0-[03]--
| +-01.0-[04-38]--
| \-02.0-[39]----00.0
+-1c.4-[3a]----00.0
+-1c.5-[3b]----00.0
+-1d.0-[3c]----00.0
+-1f.0
+-1f.2
+-1f.3
\-1f.4
$ lsusb -t
/: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 10000M
|__ Port 2: Dev 3, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
|__ Port 1: Dev 3, If 0, Class=Human Interface Device,
Driver=usbhid, 12M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
|__ Port 3: Dev 2, If 0, Class=Wireless, Driver=, 12M
|__ Port 3: Dev 2, If 1, Class=Wireless, Driver=, 12M
|__ Port 4: Dev 3, If 0, Class=Human Interface Device,
Driver=usbhid, 12M
|__ Port 5: Dev 4, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 5: Dev 4, If 1, Class=Video, Driver=uvcvideo, 480M
```
On Sun, Nov 19, 2023 at 02:42:58PM +0100, Paul Menzel wrote:
> [Fix typo in subject line]
>
> Dear Linux folks,
>
>
> On the Dell XPS 13 9360 from 2016, BIOS 2.21.0 06/02/2022, with Debian
> sid/unstable and Debian’s Linux 6.5.10 kernel, I am trying to extend the
> run-time with battery, at under 50 % of it’s original capacity, and I am
> using PowerTOP 2.15.
> Although radio/wireless devices are turned off in GNOME, PowerTOP shows the
> Bluetooth device drawing 0.85 W of energy:
>
> 848 mW 100.0% Device USB device: usb-device-0cf3-e300
>
> $ lsusb -d 0cf3:e300
> Bus 001 Device 002: ID 0cf3:e300 Qualcomm Atheros Communications QCA61x4
> Bluetooth 4.0
> After unloading the module `btusb`, the entry disappears from the PowerTOP
> list after a while.
>
> usbcore: deregistering interface driver btusb
>
> Auto-suspend was enabled for the device. (Though it shouldn’t have mattered
> as it was disabled in GNOME?)
Enabling autosuspend means that the device _may_ go into runtime suspend
when it's not being used. Whether it _will_ do so depends on the driver
(btusb in this case).
> Anyways, have you heard of such an issue? Can I provide more information, to
> get it to not use any energy while being disable in GNOME?
What is the output from
grep . /sys/bus/usb/devices/1-3/power/*
both with and without the btusb module loaded?
Alan Stern
> $ lsusb -t
> /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M
> |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 10000M
> |__ Port 2: Dev 3, If 0, Class=Vendor Specific Class, Driver=r8152,
> 5000M
> /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M
> |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
> |__ Port 1: Dev 3, If 0, Class=Human Interface Device,
> Driver=usbhid, 12M
> /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
> /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
> |__ Port 3: Dev 2, If 0, Class=Wireless, Driver=, 12M
> |__ Port 3: Dev 2, If 1, Class=Wireless, Driver=, 12M
> |__ Port 4: Dev 3, If 0, Class=Human Interface Device, Driver=usbhid,
> 12M
> |__ Port 5: Dev 4, If 0, Class=Video, Driver=uvcvideo, 480M
> |__ Port 5: Dev 4, If 1, Class=Video, Driver=uvcvideo, 480M
> ```