This patch adds the 0cf3:e500 Bluetooth device (from a QCA9377 board) as a
QCA_ROME device. It appears to be functionally identical to another device
ID, also from a QCA9377 board, which was previously marked as QCA_ROME in
0a03f98b98c201191e3ba15a0e33f46d8660e1fd
("Bluetooth: Add a new 04ca:3015 QCA_ROME device").
Without this patch, the WiFi side of the QCA9377 board is slow or unusable
when the Bluetooth side is in use.
See https://askubuntu.com/a/1137852 for another report of QCA_ROME fixing
this issue for this device ID.
/sys/kernel/debug/usb/devices:
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e500 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Daniel Lenski <[email protected]>
---
drivers/bluetooth/btusb.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 5d603ef39..ba339e074 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -270,6 +270,8 @@ static const struct usb_device_id blacklist_table[] = {
BTUSB_WIDEBAND_SPEECH },
{ USB_DEVICE(0x0cf3, 0xe360), .driver_info = BTUSB_QCA_ROME |
BTUSB_WIDEBAND_SPEECH },
+ { USB_DEVICE(0x0cf3, 0xe500), .driver_info = BTUSB_QCA_ROME |
+ BTUSB_WIDEBAND_SPEECH },
{ USB_DEVICE(0x0489, 0xe092), .driver_info = BTUSB_QCA_ROME |
BTUSB_WIDEBAND_SPEECH },
{ USB_DEVICE(0x0489, 0xe09f), .driver_info = BTUSB_QCA_ROME |
--
2.17.1
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=484479
---Test result---
Test Summary:
CheckPatch FAIL 0.49 seconds
GitLint PASS 0.11 seconds
BuildKernel PASS 562.85 seconds
TestRunner: Setup PASS 366.25 seconds
TestRunner: l2cap-tester PASS 2.74 seconds
TestRunner: bnep-tester PASS 1.99 seconds
TestRunner: mgmt-tester PASS 27.50 seconds
TestRunner: rfcomm-tester PASS 2.17 seconds
TestRunner: sco-tester PASS 2.15 seconds
TestRunner: smp-tester PASS 2.25 seconds
TestRunner: userchan-tester PASS 1.97 seconds
Details
##############################
Test: CheckPatch - FAIL - 0.49 seconds
Run checkpatch.pl script with rule in .checkpatch.conf
Bluetooth: Add a new QCA_ROME device (0cf3:e500)
ERROR: Please use git commit description style 'commit <12+ chars of sha1> ("<title line>")' - ie: 'commit fatal: bad o ("a0e33f46d8660e1fd")'
#9:
0a03f98b98c201191e3ba15a0e33f46d8660e1fd
total: 1 errors, 0 warnings, 8 lines checked
NOTE: For some of the reported defects, checkpatch may be able to
mechanically convert to the typical style using --fix or --fix-inplace.
"[PATCH] Bluetooth: Add a new QCA_ROME device (0cf3:e500)" has style problems, please review.
NOTE: If any of the errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
##############################
Test: GitLint - PASS - 0.11 seconds
Run gitlint with rule in .gitlint
##############################
Test: BuildKernel - PASS - 562.85 seconds
Build Kernel with minimal configuration supports Bluetooth
##############################
Test: TestRunner: Setup - PASS - 366.25 seconds
Setup environment for running Test Runner
##############################
Test: TestRunner: l2cap-tester - PASS - 2.74 seconds
Run test-runner with l2cap-tester
Total: 40, Passed: 40 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: bnep-tester - PASS - 1.99 seconds
Run test-runner with bnep-tester
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: mgmt-tester - PASS - 27.50 seconds
Run test-runner with mgmt-tester
Total: 416, Passed: 403 (96.9%), Failed: 0, Not Run: 13
##############################
Test: TestRunner: rfcomm-tester - PASS - 2.17 seconds
Run test-runner with rfcomm-tester
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: sco-tester - PASS - 2.15 seconds
Run test-runner with sco-tester
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: smp-tester - PASS - 2.25 seconds
Run test-runner with smp-tester
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: userchan-tester - PASS - 1.97 seconds
Run test-runner with userchan-tester
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
Hi Daniel,
> This patch adds the 0cf3:e500 Bluetooth device (from a QCA9377 board) as a
> QCA_ROME device. It appears to be functionally identical to another device
> ID, also from a QCA9377 board, which was previously marked as QCA_ROME in
> 0a03f98b98c201191e3ba15a0e33f46d8660e1fd
> ("Bluetooth: Add a new 04ca:3015 QCA_ROME device").
>
> Without this patch, the WiFi side of the QCA9377 board is slow or unusable
> when the Bluetooth side is in use.
>
> See https://askubuntu.com/a/1137852 for another report of QCA_ROME fixing
> this issue for this device ID.
>
> /sys/kernel/debug/usb/devices:
>
> T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
> D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=0cf3 ProdID=e500 Rev= 0.01
> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>
> Signed-off-by: Daniel Lenski <[email protected]>
> ---
> drivers/bluetooth/btusb.c | 2 ++
> 1 file changed, 2 insertions(+)
patch has been applied to bluetooth-next tree.
Regards
Marcel