From: Joakim Tjernlund <[email protected]>
According Realteks own BT drivers firmware RTL8761B is for UART
and RTL8761BU is for USB.
Change existing 8761B to UART and add an 8761BU entry for USB
Signed-off-by: Joakim Tjernlund <[email protected]>
---
drivers/bluetooth/btrtl.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/bluetooth/btrtl.c b/drivers/bluetooth/btrtl.c
index e7fe5fb22753..ccef8b2cfee2 100644
--- a/drivers/bluetooth/btrtl.c
+++ b/drivers/bluetooth/btrtl.c
@@ -132,12 +132,19 @@ static const struct id_table ic_id_table[] = {
.cfg_name = "rtl_bt/rtl8761a_config" },
/* 8761B */
- { IC_INFO(RTL_ROM_LMP_8761A, 0xb, 0xa, HCI_USB),
+ { IC_INFO(RTL_ROM_LMP_8761A, 0xb, 0xa, HCI_UART),
.config_needed = false,
.has_rom_version = true,
.fw_name = "rtl_bt/rtl8761b_fw.bin",
.cfg_name = "rtl_bt/rtl8761b_config" },
+ /* 8761BU */
+ { IC_INFO(RTL_ROM_LMP_8761A, 0xb, 0xa, HCI_USB),
+ .config_needed = false,
+ .has_rom_version = true,
+ .fw_name = "rtl_bt/rtl8761bu_fw.bin",
+ .cfg_name = "rtl_bt/rtl8761bu_config" },
+
/* 8822C with UART interface */
{ IC_INFO(RTL_ROM_LMP_8822B, 0xc, 0xa, HCI_UART),
.config_needed = true,
--
2.31.1
On Fri, May 28, 2021 at 05:26:44PM +0200, Joakim Tjernlund wrote:
> From: Joakim Tjernlund <[email protected]>
>
> According Realteks own BT drivers firmware RTL8761B is for UART
> and RTL8761BU is for USB.
>
> Change existing 8761B to UART and add an 8761BU entry for USB
>
> Signed-off-by: Joakim Tjernlund <[email protected]>
> ---
> drivers/bluetooth/btrtl.c | 9 ++++++++-
> 1 file changed, 8 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/bluetooth/btrtl.c b/drivers/bluetooth/btrtl.c
> index e7fe5fb22753..ccef8b2cfee2 100644
> --- a/drivers/bluetooth/btrtl.c
> +++ b/drivers/bluetooth/btrtl.c
> @@ -132,12 +132,19 @@ static const struct id_table ic_id_table[] = {
> .cfg_name = "rtl_bt/rtl8761a_config" },
>
> /* 8761B */
> - { IC_INFO(RTL_ROM_LMP_8761A, 0xb, 0xa, HCI_USB),
> + { IC_INFO(RTL_ROM_LMP_8761A, 0xb, 0xa, HCI_UART),
> .config_needed = false,
> .has_rom_version = true,
> .fw_name = "rtl_bt/rtl8761b_fw.bin",
> .cfg_name = "rtl_bt/rtl8761b_config" },
>
> + /* 8761BU */
> + { IC_INFO(RTL_ROM_LMP_8761A, 0xb, 0xa, HCI_USB),
> + .config_needed = false,
> + .has_rom_version = true,
> + .fw_name = "rtl_bt/rtl8761bu_fw.bin",
> + .cfg_name = "rtl_bt/rtl8761bu_config" },
> +
> /* 8822C with UART interface */
> { IC_INFO(RTL_ROM_LMP_8822B, 0xc, 0xa, HCI_UART),
> .config_needed = true,
> --
> 2.31.1
>
<formletter>
This is not the correct way to submit patches for inclusion in the
stable kernel tree. Please read:
https://www.kernel.org/doc/html/latest/process/stable-kernel-rules.html
for how to do this properly.
</formletter>
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=490331
---Test result---
Test Summary:
CheckPatch FAIL 1.07 seconds
GitLint FAIL 0.24 seconds
BuildKernel PASS 672.40 seconds
TestRunner: Setup PASS 437.99 seconds
TestRunner: l2cap-tester PASS 3.25 seconds
TestRunner: bnep-tester PASS 2.24 seconds
TestRunner: mgmt-tester PASS 31.34 seconds
TestRunner: rfcomm-tester PASS 2.43 seconds
TestRunner: sco-tester PASS 2.33 seconds
TestRunner: smp-tester PASS 2.57 seconds
TestRunner: userchan-tester PASS 2.15 seconds
Details
##############################
Test: CheckPatch - FAIL - 1.07 seconds
Run checkpatch.pl script with rule in .checkpatch.conf
Bluetooth: btusb: Add 0x0b05:0x190e Realtek 8761BU (ASUS BT500) device.
ERROR: code indent should use tabs where possible
#48: FILE: drivers/bluetooth/btusb.c:437:
+^I ^I^I^I^I^I BTUSB_WIDEBAND_SPEECH },$
WARNING: please, no space before tabs
#48: FILE: drivers/bluetooth/btusb.c:437:
+^I ^I^I^I^I^I BTUSB_WIDEBAND_SPEECH },$
total: 1 errors, 1 warnings, 10 lines checked
NOTE: For some of the reported defects, checkpatch may be able to
mechanically convert to the typical style using --fix or --fix-inplace.
NOTE: Whitespace errors detected.
You may wish to use scripts/cleanpatch or scripts/cleanfile
"[PATCH] Bluetooth: btusb: Add 0x0b05:0x190e Realtek 8761BU (ASUS" has style problems, please review.
NOTE: If any of the errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
##############################
Test: GitLint - FAIL - 0.24 seconds
Run gitlint with rule in .gitlint
Bluetooth: btusb: Add 0x0b05:0x190e Realtek 8761BU (ASUS BT500) device.
1: T3 Title has trailing punctuation (.): "Bluetooth: btusb: Add 0x0b05:0x190e Realtek 8761BU (ASUS BT500) device."
##############################
Test: BuildKernel - PASS - 672.40 seconds
Build Kernel with minimal configuration supports Bluetooth
##############################
Test: TestRunner: Setup - PASS - 437.99 seconds
Setup environment for running Test Runner
##############################
Test: TestRunner: l2cap-tester - PASS - 3.25 seconds
Run test-runner with l2cap-tester
Total: 40, Passed: 40 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: bnep-tester - PASS - 2.24 seconds
Run test-runner with bnep-tester
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: mgmt-tester - PASS - 31.34 seconds
Run test-runner with mgmt-tester
Total: 433, Passed: 420 (97.0%), Failed: 0, Not Run: 13
##############################
Test: TestRunner: rfcomm-tester - PASS - 2.43 seconds
Run test-runner with rfcomm-tester
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: sco-tester - PASS - 2.33 seconds
Run test-runner with sco-tester
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: smp-tester - PASS - 2.57 seconds
Run test-runner with smp-tester
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner: userchan-tester - PASS - 2.15 seconds
Run test-runner with userchan-tester
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
Hi Joakim,
> According Realteks own BT drivers firmware RTL8761B is for UART
> and RTL8761BU is for USB.
>
> Change existing 8761B to UART and add an 8761BU entry for USB
>
> Signed-off-by: Joakim Tjernlund <[email protected]>
> ---
> drivers/bluetooth/btrtl.c | 9 ++++++++-
> 1 file changed, 8 insertions(+), 1 deletion(-)
patch has been applied to bluetooth-next tree.
Regards
Marcel