This v3 of the patchset is somewhat of an RFC/RFT, and also just something to
get this out there.
First things first, I do not have access to the specs nor the schematics, so a
lot of this was done via guess work, looking at the acpi tables, and looking at
how a similar device (wcn6750) was added.
There are possibly checkpatch warnings, and I do apologize to those who won't
review things until there are no warnings for wasting your time, I did try to
correct the ones I came across and seemed to be needed.
One example is that I have the vregs commented out, the dt-bindings say that
they are required since it's based on the wcn6750 work but also like the 6750,
I've added defaults into the driver, and those seem to work, at least for the
initial testing.
The end result is that we do have a working device, but not entirely reliable.
Hopefully by getting this out there, people who do have access to the specs or
schematics can see where the improvements or fixes need to come.
There are a few things that I am not sure why they happen, and don't have the
knowledge level to figure out why they happen or debugging it.
Bluetooth: hci0: setting up wcn6855
Bluetooth: hci0: Frame reassembly failed (-84)
Bluetooth: hci0: QCA Product ID :0x00000013
Bluetooth: hci0: QCA SOC Version :0x400c0210
Bluetooth: hci0: QCA ROM Version :0x00000201
Bluetooth: hci0: QCA Patch Version:0x000038e6
Bluetooth: hci0: QCA controller version 0x02100201
Bluetooth: hci0: unexpected event for opcode 0xfc48
Bluetooth: hci0: Sending QCA Patch config failed (-110)
Bluetooth: hci0: QCA Downloading qca/hpbtfw21.tlv
Bluetooth: hci0: QCA Downloading qca/hpnv21g.bin
Bluetooth: hci0: QCA setup on UART is completed
I do not know why the Frame assembly failed, nor the unexpected event.
Likewise, I'm not entirely sure why it says the patch config send times out, and
*then* seems to send it?
The BD Address also seems to be incorrect, and I'm not sure what is going on
there either.
Testing was done by connecting a Razer Orochi bluetooth mouse, and using it, as
well as connecting to and using an H2GO bluetooth speaker and playing audio out
via canberra-gtk-play as well as a couple of YouTube videos in a browser.
The mouse only seems to work when < 2 ft. from the laptop, and for the speaker, only
"A2DP Sink, codec SBC" would provide audio output, and while I could see that
data was being sent to the speaker, it wasn't always outputting, and going >
4ft. away, would often disconnect.
steev@wintermute:~$ hciconfig -a
hci0: Type: Primary Bus: UART
BD Address: 00:00:00:00:5A:AD ACL MTU: 1024:8 SCO MTU: 240:4
UP RUNNING PSCAN
RX bytes:1492 acl:0 sco:0 events:126 errors:0
TX bytes:128743 acl:0 sco:0 commands:597 errors:0
Features: 0xff 0xfe 0x8f 0xfe 0xd8 0x3f 0x5b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF
Link mode: PERIPHERAL ACCEPT
Name: 'wintermute'
Class: 0x0c010c
Service Classes: Rendering, Capturing
Device Class: Computer, Laptop
HCI Version: (0xc) Revision: 0x0
LMP Version: (0xc) Subversion: 0x46f7
Manufacturer: Qualcomm (29)
steev@wintermute:~$ dmesg | grep Razer
[ 3089.235440] input: Razer Orochi as /devices/virtual/misc/uhid/0005:1532:0056.0003/input/input11
[ 3089.238580] hid-generic 0005:1532:0056.0003: input,hidraw2: BLUETOOTH HID v0.01 Mouse [Razer Orochi] on 00:00:00:00:5a:ad
steev@wintermute:~$ dmesg | grep H2GO
[ 3140.959947] input: H2GO Speaker (AVRCP) as /devices/virtual/input/input12
Changes since v2:
- Drop unnecessary commit info from patch 2
- Remove dead code in patch 4, add TODO note.
- Make dtbs_check happy with the pin definitions
Bjorn Andersson (1):
arm64: dts: qcom: sc8280xp: Define uart2
Steev Klimaszewski (3):
dt-bindings: net: Add WCN6855 Bluetooth
Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855
arm64: dts: qcom: thinkpad-x13s: Add bluetooth
.../net/bluetooth/qualcomm-bluetooth.yaml | 2 +
.../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 63 +++++++++++++++++++
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 14 +++++
drivers/bluetooth/btqca.c | 24 ++++++-
drivers/bluetooth/btqca.h | 10 +++
drivers/bluetooth/hci_qca.c | 59 +++++++++++++----
6 files changed, 157 insertions(+), 15 deletions(-)
base-commit: 4fafd96910add124586b549ad005dcd179de8a18
--
2.39.0
Add bindings for the QTI WCN6855 chipset, based on the WCN6750.
---
- v3 No changes from v2
- v2 drop second binding in subject line
Signed-off-by: Steev Klimaszewski <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
.../devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml
index a6a6b0e4df7a..64e278561ba8 100644
--- a/Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml
+++ b/Documentation/devicetree/bindings/net/bluetooth/qualcomm-bluetooth.yaml
@@ -23,6 +23,7 @@ properties:
- qcom,wcn3998-bt
- qcom,qca6390-bt
- qcom,wcn6750-bt
+ - qcom,wcn6855-bt
enable-gpios:
maxItems: 1
@@ -121,6 +122,7 @@ allOf:
contains:
enum:
- qcom,wcn6750-bt
+ - qcom,wcn6855-bt
then:
required:
- enable-gpios
--
2.39.0
Added regulators,GPIOs and changes required to power on/off wcn6855.
Added support for firmware download for wcn6855.
---
Changes since v2:
- drop unnecessary commit info
Signed-off-by: Steev Klimaszewski <[email protected]>
---
drivers/bluetooth/btqca.c | 24 +++++++++++++--
drivers/bluetooth/btqca.h | 10 +++++++
drivers/bluetooth/hci_qca.c | 59 +++++++++++++++++++++++++++++--------
3 files changed, 78 insertions(+), 15 deletions(-)
diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index c9064d34d830..456b961b9554 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -472,6 +472,19 @@ static int qca_download_firmware(struct hci_dev *hdev,
config->fwname, ret);
return ret;
}
+ } else if (soc_type == QCA_WCN6855 && config->type == ELF_TYPE_PATCH) {
+ bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ config->type = TLV_TYPE_PATCH;
+ snprintf(config->fwname, sizeof(config->fwname),
+ "qca/hpbtfw%02x.tlv", rom_ver);
+ bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
+ ret = request_firmware(&fw, config->fwname, &hdev->dev);
+ if (ret) {
+ bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ return ret;
+ }
} else {
bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
config->fwname, ret);
@@ -596,7 +609,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
*/
rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
- if (soc_type == QCA_WCN6750)
+ if (soc_type == QCA_WCN6750 || soc_type == QCA_WCN6855)
qca_send_patch_config_cmd(hdev);
/* Download rampatch file */
@@ -614,6 +627,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
config.type = ELF_TYPE_PATCH;
snprintf(config.fwname, sizeof(config.fwname),
"qca/msbtfw%02x.mbn", rom_ver);
+ } else if (soc_type == QCA_WCN6855) {
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/hpbtfw%02x.tlv", rom_ver);
} else {
snprintf(config.fwname, sizeof(config.fwname),
"qca/rampatch_%08x.bin", soc_ver);
@@ -648,6 +664,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
else if (soc_type == QCA_WCN6750)
snprintf(config.fwname, sizeof(config.fwname),
"qca/msnv%02x.bin", rom_ver);
+ else if (soc_type == QCA_WCN6855)
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/hpnv%02x.bin", rom_ver);
else
snprintf(config.fwname, sizeof(config.fwname),
"qca/nvm_%08x.bin", soc_ver);
@@ -672,6 +691,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
case QCA_WCN3991:
case QCA_WCN3998:
case QCA_WCN6750:
+ case QCA_WCN6855:
hci_set_msft_opcode(hdev, 0xFD70);
break;
default:
@@ -685,7 +705,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
return err;
}
- if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750) {
+ if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750 || soc_type == QCA_WCN6855) {
/* get fw build info */
err = qca_read_fw_build_info(hdev);
if (err < 0)
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index 61e9a50e66ae..b884095bcd9d 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -147,6 +147,7 @@ enum qca_btsoc_type {
QCA_WCN3991,
QCA_QCA6390,
QCA_WCN6750,
+ QCA_WCN6855,
};
#if IS_ENABLED(CONFIG_BT_QCA)
@@ -168,6 +169,10 @@ static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
{
return soc_type == QCA_WCN6750;
}
+static inline bool qca_is_wcn6855(enum qca_btsoc_type soc_type)
+{
+ return soc_type == QCA_WCN6855;
+}
#else
@@ -206,6 +211,11 @@ static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
return false;
}
+static inline bool qca_is_wcn6855(enum qca_btsoc_type soc_type)
+{
+ return false;
+}
+
static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
{
return -EOPNOTSUPP;
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 3df8c3606e93..6c23c856d51b 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -606,7 +606,8 @@ static int qca_open(struct hci_uart *hu)
qcadev = serdev_device_get_drvdata(hu->serdev);
if (qca_is_wcn399x(qcadev->btsoc_type) ||
- qca_is_wcn6750(qcadev->btsoc_type))
+ qca_is_wcn6750(qcadev->btsoc_type) ||
+ qca_is_wcn6855(qcadev->btsoc_type))
hu->init_speed = qcadev->init_speed;
if (qcadev->oper_speed)
@@ -1317,7 +1318,8 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
/* Give the controller time to process the request */
if (qca_is_wcn399x(qca_soc_type(hu)) ||
- qca_is_wcn6750(qca_soc_type(hu)))
+ qca_is_wcn6750(qca_soc_type(hu)) ||
+ qca_is_wcn6855(qca_soc_type(hu)))
usleep_range(1000, 10000);
else
msleep(300);
@@ -1394,7 +1396,8 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
static int qca_check_speeds(struct hci_uart *hu)
{
if (qca_is_wcn399x(qca_soc_type(hu)) ||
- qca_is_wcn6750(qca_soc_type(hu))) {
+ qca_is_wcn6750(qca_soc_type(hu)) ||
+ qca_is_wcn6855(qca_soc_type(hu))) {
if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
!qca_get_speed(hu, QCA_OPER_SPEED))
return -EINVAL;
@@ -1428,7 +1431,8 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
* changing the baudrate of chip and host.
*/
if (qca_is_wcn399x(soc_type) ||
- qca_is_wcn6750(soc_type))
+ qca_is_wcn6750(soc_type) ||
+ qca_is_wcn6855(soc_type))
hci_uart_set_flow_control(hu, true);
if (soc_type == QCA_WCN3990) {
@@ -1446,7 +1450,8 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
error:
if (qca_is_wcn399x(soc_type) ||
- qca_is_wcn6750(soc_type))
+ qca_is_wcn6750(soc_type) ||
+ qca_is_wcn6855(soc_type))
hci_uart_set_flow_control(hu, false);
if (soc_type == QCA_WCN3990) {
@@ -1682,7 +1687,8 @@ static int qca_power_on(struct hci_dev *hdev)
return 0;
if (qca_is_wcn399x(soc_type) ||
- qca_is_wcn6750(soc_type)) {
+ qca_is_wcn6750(soc_type) ||
+ qca_is_wcn6855(soc_type)) {
ret = qca_regulator_init(hu);
} else {
qcadev = serdev_device_get_drvdata(hu->serdev);
@@ -1723,7 +1729,8 @@ static int qca_setup(struct hci_uart *hu)
bt_dev_info(hdev, "setting up %s",
qca_is_wcn399x(soc_type) ? "wcn399x" :
- (soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
+ (soc_type == QCA_WCN6750) ? "wcn6750" :
+ (soc_type == QCA_WCN6855) ? "wcn6855" : "ROME/QCA6390");
qca->memdump_state = QCA_MEMDUMP_IDLE;
@@ -1735,7 +1742,8 @@ static int qca_setup(struct hci_uart *hu)
clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
if (qca_is_wcn399x(soc_type) ||
- qca_is_wcn6750(soc_type)) {
+ qca_is_wcn6750(soc_type) ||
+ qca_is_wcn6855(soc_type)) {
set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
hci_set_aosp_capable(hdev);
@@ -1757,7 +1765,8 @@ static int qca_setup(struct hci_uart *hu)
}
if (!(qca_is_wcn399x(soc_type) ||
- qca_is_wcn6750(soc_type))) {
+ qca_is_wcn6750(soc_type) ||
+ qca_is_wcn6855(soc_type))) {
/* Get QCA version information */
ret = qca_read_soc_version(hdev, &ver, soc_type);
if (ret)
@@ -1883,6 +1892,23 @@ static const struct qca_device_data qca_soc_data_wcn6750 = {
.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
};
+static const struct qca_device_data qca_soc_data_wcn6855 = {
+ .soc_type = QCA_WCN6855,
+ .vregs = (struct qca_vreg []) {
+ { "vddio", 5000 },
+ { "vddaon", 26000 },
+ { "vddbtcxmx", 126000 },
+ { "vddrfacmn", 12500 },
+ { "vddrfa0p8", 102000 },
+ { "vddrfa1p7", 302000 },
+ { "vddrfa1p2", 257000 },
+ { "vddrfa2p2", 1700000 },
+ { "vddasd", 200 },
+ },
+ .num_vregs = 9,
+ .capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
+};
+
static void qca_power_shutdown(struct hci_uart *hu)
{
struct qca_serdev *qcadev;
@@ -2047,7 +2073,8 @@ static int qca_serdev_probe(struct serdev_device *serdev)
if (data &&
(qca_is_wcn399x(data->soc_type) ||
- qca_is_wcn6750(data->soc_type))) {
+ qca_is_wcn6750(data->soc_type) ||
+ qca_is_wcn6855(data->soc_type))) {
qcadev->btsoc_type = data->soc_type;
qcadev->bt_power = devm_kzalloc(&serdev->dev,
sizeof(struct qca_power),
@@ -2067,14 +2094,18 @@ static int qca_serdev_probe(struct serdev_device *serdev)
qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
GPIOD_OUT_LOW);
- if (IS_ERR_OR_NULL(qcadev->bt_en) && data->soc_type == QCA_WCN6750) {
+ if (IS_ERR_OR_NULL(qcadev->bt_en)
+ && (data->soc_type == QCA_WCN6750 ||
+ data->soc_type == QCA_WCN6855)) {
dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
power_ctrl_enabled = false;
}
qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
GPIOD_IN);
- if (IS_ERR_OR_NULL(qcadev->sw_ctrl) && data->soc_type == QCA_WCN6750)
+ if (IS_ERR_OR_NULL(qcadev->sw_ctrl)
+ && (data->soc_type == QCA_WCN6750 ||
+ data->soc_type == QCA_WCN6855))
dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
@@ -2150,7 +2181,8 @@ static void qca_serdev_remove(struct serdev_device *serdev)
struct qca_power *power = qcadev->bt_power;
if ((qca_is_wcn399x(qcadev->btsoc_type) ||
- qca_is_wcn6750(qcadev->btsoc_type)) &&
+ qca_is_wcn6750(qcadev->btsoc_type) ||
+ qca_is_wcn6855(qcadev->btsoc_type)) &&
power->vregs_on)
qca_power_shutdown(&qcadev->serdev_hu);
else if (qcadev->susclk)
@@ -2335,6 +2367,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
{ .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
+ { .compatible = "qcom,wcn6855-bt", .data = &qca_soc_data_wcn6855},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
--
2.39.0
---
Changes since v2:
- Remove dead code and add TODO comment
- Make dtbs_check happy with the pin definitions
Signed-off-by: Steev Klimaszewski <[email protected]>
---
.../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 63 +++++++++++++++++++
1 file changed, 63 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
index f936b020a71d..d351411d3504 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -24,6 +24,8 @@ / {
aliases {
i2c4 = &i2c4;
i2c21 = &i2c21;
+ serial0 = &uart17;
+ serial1 = &uart2;
};
wcd938x: audio-codec {
@@ -712,6 +714,27 @@ &qup0 {
status = "okay";
};
+&uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_state>;
+
+ bluetooth {
+ compatible = "qcom,wcn6855-bt";
+
+ /* TODO: define regulators */
+
+ max-speed = <3200000>;
+
+ enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
+ swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en>;
+ };
+};
+
&qup1 {
status = "okay";
};
@@ -720,6 +743,12 @@ &qup2 {
status = "okay";
};
+&uart17 {
+ compatible = "qcom,geni-debug-uart";
+
+ status = "okay";
+};
+
&remoteproc_adsp {
firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn";
@@ -980,6 +1009,19 @@ hastings_reg_en: hastings-reg-en-state {
&tlmm {
gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+ bt_en: bt-en-state {
+ hstp-sw-ctrl-pins {
+ pins = "gpio132";
+ function = "gpio";
+ };
+
+ hstp-bt-en-pins {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <16>;
+ };
+ };
+
edp_reg_en: edp-reg-en-state {
pins = "gpio25";
function = "gpio";
@@ -1001,6 +1043,27 @@ i2c4_default: i2c4-default-state {
bias-disable;
};
+ uart2_state: uart2-state {
+ cts-pins {
+ pins = "gpio122";
+ function = "qup2";
+ bias-disable;
+ };
+
+ rts-tx-pins {
+ pins = "gpio122", "gpio123";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx-pins {
+ pins = "gpio124";
+ function = "qup2";
+ bias-pull-up;
+ };
+ };
+
i2c21_default: i2c21-default-state {
pins = "gpio81", "gpio82";
function = "qup21";
--
2.39.0
From: Bjorn Andersson <[email protected]>
---
- v3 No changes since v2
- v2 change subject line, move node, and add my s-o-b
Signed-off-by: Bjorn Andersson <[email protected]>
Signed-off-by: Steev Klimaszewski <[email protected]>
Reviewed-by: Brian Masney <[email protected]>
---
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index fa2d0d7d1367..eab54aab3b76 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -1207,6 +1207,20 @@ spi2: spi@988000 {
status = "disabled";
};
+ uart2: serial@988000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00988000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ operating-points-v2 = <&qup_opp_table_100mhz>;
+ power-domains = <&rpmhpd SC8280XP_CX>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
i2c3: i2c@98c000 {
compatible = "qcom,geni-i2c";
reg = <0 0x0098c000 0 0x4000>;
--
2.39.0
This is an automated email and please do not reply to this email.
Dear Submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
While preparing the CI tests, the patches you submitted couldn't be applied to the current HEAD of the repository.
----- Output -----
error: patch failed: arch/arm64/boot/dts/qcom/sc8280xp.dtsi:1207
error: arch/arm64/boot/dts/qcom/sc8280xp.dtsi: patch does not apply
hint: Use 'git am --show-current-patch' to see the failed patch
Please resolve the issue and submit the patches again.
---
Regards,
Linux Bluetooth
On 06/02/2023 01:16, Steev Klimaszewski wrote:
> Add bindings for the QTI WCN6855 chipset, based on the WCN6750.
>
> ---
> - v3 No changes from v2
> - v2 drop second binding in subject line
>
> Signed-off-by: Steev Klimaszewski <[email protected]>
> Acked-by: Krzysztof Kozlowski <[email protected]>
Still broken.
Best regards,
Krzysztof
On Sun, Feb 05, 2023 at 06:16:34PM -0600, Steev Klimaszewski wrote:
> ---
This marks the end of the commit message, as such your S-o-b is
"missing". Move it above the "---" line.
It's also recommended to include some body in your commit message.
Perhaps just "The ... has a WCN6855 Bluetooth controller on uart2, add
this".
> Changes since v2:
And keep the change log here.
> - Remove dead code and add TODO comment
> - Make dtbs_check happy with the pin definitions
>
> Signed-off-by: Steev Klimaszewski <[email protected]>
> ---
> .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 63 +++++++++++++++++++
> 1 file changed, 63 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> index f936b020a71d..d351411d3504 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> @@ -24,6 +24,8 @@ / {
> aliases {
> i2c4 = &i2c4;
> i2c21 = &i2c21;
> + serial0 = &uart17;
> + serial1 = &uart2;
> };
>
> wcd938x: audio-codec {
> @@ -712,6 +714,27 @@ &qup0 {
> status = "okay";
> };
>
> +&uart2 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_state>;
> +
> + bluetooth {
> + compatible = "qcom,wcn6855-bt";
> +
> + /* TODO: define regulators */
You have the list of regulators in the driver, and there are people with
the schematics. You should be able to fill this list out.
Regards,
Bjorn
> +
> + max-speed = <3200000>;
> +
> + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
> + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_en>;
> + };
> +};
> +
> &qup1 {
> status = "okay";
> };
> @@ -720,6 +743,12 @@ &qup2 {
> status = "okay";
> };
>
> +&uart17 {
> + compatible = "qcom,geni-debug-uart";
> +
> + status = "okay";
> +};
> +
> &remoteproc_adsp {
> firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn";
>
> @@ -980,6 +1009,19 @@ hastings_reg_en: hastings-reg-en-state {
> &tlmm {
> gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>
> + bt_en: bt-en-state {
> + hstp-sw-ctrl-pins {
> + pins = "gpio132";
> + function = "gpio";
> + };
> +
> + hstp-bt-en-pins {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <16>;
> + };
> + };
> +
> edp_reg_en: edp-reg-en-state {
> pins = "gpio25";
> function = "gpio";
> @@ -1001,6 +1043,27 @@ i2c4_default: i2c4-default-state {
> bias-disable;
> };
>
> + uart2_state: uart2-state {
> + cts-pins {
> + pins = "gpio122";
> + function = "qup2";
> + bias-disable;
> + };
> +
> + rts-tx-pins {
> + pins = "gpio122", "gpio123";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx-pins {
> + pins = "gpio124";
> + function = "qup2";
> + bias-pull-up;
> + };
> + };
> +
> i2c21_default: i2c21-default-state {
> pins = "gpio81", "gpio82";
> function = "qup21";
> --
> 2.39.0
>