We may need to specify a GPIO wake pin for this device, so add a
compatible property for it.
There are at least to USB PID/VID variations of this chip: one with a
Lite-On ID and one with an Atheros ID.
Signed-off-by: Brian Norris <[email protected]>
---
drivers/bluetooth/btusb.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 470ee68555d9..380e6f38c607 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -2862,6 +2862,8 @@ static irqreturn_t btusb_oob_wake_handler(int irq, void *priv)
static const struct of_device_id btusb_match_table[] = {
{ .compatible = "usb1286,204e" },
+ { .compatible = "usb0cf3,e300" }, /* QCA6174A */
+ { .compatible = "usb04ca,301a" }, /* QCA6174A (Lite-On) */
{ }
};
MODULE_DEVICE_TABLE(of, btusb_match_table);
--
2.21.0.rc0.258.g878e2cd30e-goog
Currently, we don't coordinate BT USB activity with our handling of the
BT out-of-band wake pin, and instead just use gpio-keys. That causes
problems because we have no way of distinguishing wake activity due to a
BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
mask before suspend). This can cause spurious wake events just because
we, for instance, try to reconfigure the host controller's event mask
before suspending.
We can avoid these synchronization problems by handling the BT wake pin
directly in the btusb driver -- for all activity up until BT controller
suspend(), we simply listen to normal USB activity (e.g., to know the
difference between device and host activity); once we're really ready to
suspend the host controller, there should be no more host activity, and
only *then* do we unmask the GPIO interrupt.
This is already supported by btusb; we just need to describe the wake
pin in the right node.
We list 2 compatible properties, since both PID/VID pairs show up on
Scarlet devices, and they're both essentially identical QCA6174A-based
modules.
Also note that the polarity was wrong before: Qualcomm implemented WAKE
as active high, not active low. We only got away with this because
gpio-keys always reconfigured us as bi-directional edge-triggered.
Finally, we have an external pull-up and a level-shifter on this line
(we didn't notice Qualcomm's polarity in the initial design), so we
can't do pull-down. Switch to pull-none.
Signed-off-by: Brian Norris <[email protected]>
---
This patch is also required to make this stable, but since it's not
really tied to the device tree, and it's an existing bug, I sent it
separately:
https://lore.kernel.org/patchwork/patch/1044896/
Subject: Bluetooth: btusb: request wake pin with NOAUTOEN
.../dts/rockchip/rk3399-gru-chromebook.dtsi | 13 ++++++
.../boot/dts/rockchip/rk3399-gru-scarlet.dtsi | 46 ++++++++++++-------
arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi | 13 ------
3 files changed, 42 insertions(+), 30 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
index c400be64170e..931640e9aed4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
@@ -200,6 +200,19 @@
pinctrl-0 = <&bl_en>;
pwm-delay-us = <10000>;
};
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l>;
+
+ wake_on_bt: wake-on-bt {
+ label = "Wake-on-Bluetooth";
+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
};
&ppvar_bigcpu {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
index fc50b3ef758c..3e2196c08473 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
@@ -175,6 +175,21 @@
pinctrl-0 = <&dmic_en>;
wakeup-delay-ms = <250>;
};
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pen_eject_odl>;
+
+ pen-insert {
+ label = "Pen Insert";
+ /* Insert = low, eject = high */
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ linux,code = <SW_PEN_INSERTED>;
+ linux,input-type = <EV_SW>;
+ wakeup-source;
+ };
+ };
};
/* pp900_s0 aliases */
@@ -328,20 +343,6 @@ camera: &i2c7 {
<400000000>;
};
-&gpio_keys {
- pinctrl-names = "default";
- pinctrl-0 = <&bt_host_wake_l>, <&pen_eject_odl>;
-
- pen-insert {
- label = "Pen Insert";
- /* Insert = low, eject = high */
- gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- linux,code = <SW_PEN_INSERTED>;
- linux,input-type = <EV_SW>;
- wakeup-source;
- };
-};
-
&i2c_tunnel {
google,remote-bus = <0>;
};
@@ -437,8 +438,19 @@ camera: &i2c7 {
status = "okay";
};
-&wake_on_bt {
- gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+&usb_host0_ohci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qca_bt: bt@1 {
+ compatible = "usb0cf3,e300", "usb04ca,301a";
+ reg = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "wakeup";
+ };
};
/* PINCTRL OVERRIDES */
@@ -455,7 +467,7 @@ camera: &i2c7 {
};
&bt_host_wake_l {
- rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_up>;
+ rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_none>;
};
&ec_ap_int_l {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index ea607a601a86..da03fa9c5662 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -269,19 +269,6 @@
#clock-cells = <0>;
};
- gpio_keys: gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&bt_host_wake_l>;
-
- wake_on_bt: wake-on-bt {
- label = "Wake-on-Bluetooth";
- gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WAKEUP>;
- wakeup-source;
- };
- };
-
max98357a: max98357a {
compatible = "maxim,max98357a";
pinctrl-names = "default";
--
2.21.0.rc0.258.g878e2cd30e-goog
There are two USB PID/VID variations I've seen for this chip, and I want
to utilize the 'interrupts' property defined here already.
Signed-off-by: Brian Norris <[email protected]>
---
Documentation/devicetree/bindings/net/btusb.txt | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt
index 37d67926dd6d..43c96c3380a6 100644
--- a/Documentation/devicetree/bindings/net/btusb.txt
+++ b/Documentation/devicetree/bindings/net/btusb.txt
@@ -9,6 +9,9 @@ Required properties:
(more may be added later) are:
"usb1286,204e" (Marvell 8997)
+ "usb0cf3,e300" (Qualcomm QCA6174A)
+ "usb04ca,301a" (Qualcomm QCA6174A (Lite-On))
+
Also, vendors that use btusb may have device additional properties, e.g:
Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
--
2.21.0.rc0.258.g878e2cd30e-goog
On Thu, Feb 21, 2019 at 04:34:01PM -0800, Brian Norris wrote:
> We may need to specify a GPIO wake pin for this device, so add a
> compatible property for it.
>
> There are at least to USB PID/VID variations of this chip: one with a
> Lite-On ID and one with an Atheros ID.
>
> Signed-off-by: Brian Norris <[email protected]>
> ---
> drivers/bluetooth/btusb.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 470ee68555d9..380e6f38c607 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -2862,6 +2862,8 @@ static irqreturn_t btusb_oob_wake_handler(int irq, void *priv)
>
> static const struct of_device_id btusb_match_table[] = {
> { .compatible = "usb1286,204e" },
> + { .compatible = "usb0cf3,e300" }, /* QCA6174A */
> + { .compatible = "usb04ca,301a" }, /* QCA6174A (Lite-On) */
> { }
> };
> MODULE_DEVICE_TABLE(of, btusb_match_table);
Reviewed-by: Matthias Kaehlcke <[email protected]>
On Thu, Feb 21, 2019 at 04:34:02PM -0800, Brian Norris wrote:
> There are two USB PID/VID variations I've seen for this chip, and I want
> to utilize the 'interrupts' property defined here already.
>
> Signed-off-by: Brian Norris <[email protected]>
> ---
> Documentation/devicetree/bindings/net/btusb.txt | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt
> index 37d67926dd6d..43c96c3380a6 100644
> --- a/Documentation/devicetree/bindings/net/btusb.txt
> +++ b/Documentation/devicetree/bindings/net/btusb.txt
> @@ -9,6 +9,9 @@ Required properties:
> (more may be added later) are:
>
> "usb1286,204e" (Marvell 8997)
> + "usb0cf3,e300" (Qualcomm QCA6174A)
> + "usb04ca,301a" (Qualcomm QCA6174A (Lite-On))
> +
>
> Also, vendors that use btusb may have device additional properties, e.g:
> Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
Reviewed-by: Matthias Kaehlcke <[email protected]>
On Thu, Feb 21, 2019 at 04:34:03PM -0800, Brian Norris wrote:
> Currently, we don't coordinate BT USB activity with our handling of the
> BT out-of-band wake pin, and instead just use gpio-keys. That causes
> problems because we have no way of distinguishing wake activity due to a
> BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
> mask before suspend). This can cause spurious wake events just because
> we, for instance, try to reconfigure the host controller's event mask
> before suspending.
>
> We can avoid these synchronization problems by handling the BT wake pin
> directly in the btusb driver -- for all activity up until BT controller
> suspend(), we simply listen to normal USB activity (e.g., to know the
> difference between device and host activity); once we're really ready to
> suspend the host controller, there should be no more host activity, and
> only *then* do we unmask the GPIO interrupt.
>
> This is already supported by btusb; we just need to describe the wake
> pin in the right node.
>
> We list 2 compatible properties, since both PID/VID pairs show up on
> Scarlet devices, and they're both essentially identical QCA6174A-based
> modules.
>
> Also note that the polarity was wrong before: Qualcomm implemented WAKE
> as active high, not active low. We only got away with this because
> gpio-keys always reconfigured us as bi-directional edge-triggered.
>
> Finally, we have an external pull-up and a level-shifter on this line
> (we didn't notice Qualcomm's polarity in the initial design), so we
> can't do pull-down. Switch to pull-none.
>
> Signed-off-by: Brian Norris <[email protected]>
> ---
> This patch is also required to make this stable, but since it's not
> really tied to the device tree, and it's an existing bug, I sent it
> separately:
>
> https://lore.kernel.org/patchwork/patch/1044896/
> Subject: Bluetooth: btusb: request wake pin with NOAUTOEN
>
> .../dts/rockchip/rk3399-gru-chromebook.dtsi | 13 ++++++
> .../boot/dts/rockchip/rk3399-gru-scarlet.dtsi | 46 ++++++++++++-------
> arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi | 13 ------
> 3 files changed, 42 insertions(+), 30 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
> index c400be64170e..931640e9aed4 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
> @@ -200,6 +200,19 @@
> pinctrl-0 = <&bl_en>;
> pwm-delay-us = <10000>;
> };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_host_wake_l>;
> +
> + wake_on_bt: wake-on-bt {
> + label = "Wake-on-Bluetooth";
> + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WAKEUP>;
> + wakeup-source;
> + };
> + };
> };
>
> &ppvar_bigcpu {
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
> index fc50b3ef758c..3e2196c08473 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
> @@ -175,6 +175,21 @@
> pinctrl-0 = <&dmic_en>;
> wakeup-delay-ms = <250>;
> };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pen_eject_odl>;
> +
> + pen-insert {
> + label = "Pen Insert";
> + /* Insert = low, eject = high */
> + gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + linux,code = <SW_PEN_INSERTED>;
> + linux,input-type = <EV_SW>;
> + wakeup-source;
> + };
> + };
> };
>
> /* pp900_s0 aliases */
> @@ -328,20 +343,6 @@ camera: &i2c7 {
> <400000000>;
> };
>
> -&gpio_keys {
> - pinctrl-names = "default";
> - pinctrl-0 = <&bt_host_wake_l>, <&pen_eject_odl>;
> -
> - pen-insert {
> - label = "Pen Insert";
> - /* Insert = low, eject = high */
> - gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> - linux,code = <SW_PEN_INSERTED>;
> - linux,input-type = <EV_SW>;
> - wakeup-source;
> - };
> -};
> -
> &i2c_tunnel {
> google,remote-bus = <0>;
> };
> @@ -437,8 +438,19 @@ camera: &i2c7 {
> status = "okay";
> };
>
> -&wake_on_bt {
> - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
> +&usb_host0_ohci {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + qca_bt: bt@1 {
> + compatible = "usb0cf3,e300", "usb04ca,301a";
> + reg = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_host_wake_l>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "wakeup";
> + };
> };
I didn't know it was possible to configure (certain) USB devices
through the DT, neat!
>
> /* PINCTRL OVERRIDES */
> @@ -455,7 +467,7 @@ camera: &i2c7 {
> };
>
> &bt_host_wake_l {
> - rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_up>;
> + rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_none>;
> };
>
> &ec_ap_int_l {
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> index ea607a601a86..da03fa9c5662 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> @@ -269,19 +269,6 @@
> #clock-cells = <0>;
> };
>
> - gpio_keys: gpio-keys {
> - compatible = "gpio-keys";
> - pinctrl-names = "default";
> - pinctrl-0 = <&bt_host_wake_l>;
> -
> - wake_on_bt: wake-on-bt {
> - label = "Wake-on-Bluetooth";
> - gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_WAKEUP>;
> - wakeup-source;
> - };
> - };
> -
> max98357a: max98357a {
> compatible = "maxim,max98357a";
> pinctrl-names = "default";
Reviewed-by: Matthias Kaehlcke <[email protected]>
On 2019-02-22 12:34 am, Brian Norris wrote:
> There are two USB PID/VID variations I've seen for this chip, and I want
> to utilize the 'interrupts' property defined here already.
>
> Signed-off-by: Brian Norris <[email protected]>
> ---
> Documentation/devicetree/bindings/net/btusb.txt | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt
> index 37d67926dd6d..43c96c3380a6 100644
> --- a/Documentation/devicetree/bindings/net/btusb.txt
> +++ b/Documentation/devicetree/bindings/net/btusb.txt
> @@ -9,6 +9,9 @@ Required properties:
> (more may be added later) are:
>
> "usb1286,204e" (Marvell 8997)
> + "usb0cf3,e300" (Qualcomm QCA6174A)
> + "usb04ca,301a" (Qualcomm QCA6174A (Lite-On))
Nit: the USB device binding states that those leading zeroes in the VIDs
should be suppressed.
Otherwise, thanks for the tip-off - I hadn't realised that OOB interrupt
support was fully implemented already. I'll have to give this a go for
the Realtek module in one of my TV boxes :)
Robin.
> +
>
> Also, vendors that use btusb may have device additional properties, e.g:
> Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
>
On Fri, Feb 22, 2019 at 1:57 PM Robin Murphy <[email protected]> wrote:
> On 2019-02-22 12:34 am, Brian Norris wrote:
> > + "usb0cf3,e300" (Qualcomm QCA6174A)
> > + "usb04ca,301a" (Qualcomm QCA6174A (Lite-On))
>
> Nit: the USB device binding states that those leading zeroes in the VIDs
> should be suppressed.
Ah, thanks. Didn't notice that part. I'll remove the zeroes and resend.
Brian
On Fri, Feb 22, 2019 at 10:27 AM Matthias Kaehlcke <[email protected]> wrote:
>
> On Thu, Feb 21, 2019 at 04:34:03PM -0800, Brian Norris wrote:
> > Currently, we don't coordinate BT USB activity with our handling of the
> > BT out-of-band wake pin, and instead just use gpio-keys. That causes
> > problems because we have no way of distinguishing wake activity due to a
> > BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
> > mask before suspend). This can cause spurious wake events just because
> > we, for instance, try to reconfigure the host controller's event mask
> > before suspending.
> >
> > We can avoid these synchronization problems by handling the BT wake pin
> > directly in the btusb driver -- for all activity up until BT controller
> > suspend(), we simply listen to normal USB activity (e.g., to know the
> > difference between device and host activity); once we're really ready to
> > suspend the host controller, there should be no more host activity, and
> > only *then* do we unmask the GPIO interrupt.
> >
> > This is already supported by btusb; we just need to describe the wake
> > pin in the right node.
> >
> > We list 2 compatible properties, since both PID/VID pairs show up on
> > Scarlet devices, and they're both essentially identical QCA6174A-based
> > modules.
> >
> > Also note that the polarity was wrong before: Qualcomm implemented WAKE
> > as active high, not active low. We only got away with this because
> > gpio-keys always reconfigured us as bi-directional edge-triggered.
> >
> > Finally, we have an external pull-up and a level-shifter on this line
> > (we didn't notice Qualcomm's polarity in the initial design), so we
> > can't do pull-down. Switch to pull-none.
> >
> > Signed-off-by: Brian Norris <[email protected]>
If it matters, LGTM.
Reviewed-by: Rajat Jain <[email protected]>
> > ---
> > This patch is also required to make this stable, but since it's not
> > really tied to the device tree, and it's an existing bug, I sent it
> > separately:
> >
> > https://lore.kernel.org/patchwork/patch/1044896/
> > Subject: Bluetooth: btusb: request wake pin with NOAUTOEN
> >
> > .../dts/rockchip/rk3399-gru-chromebook.dtsi | 13 ++++++
> > .../boot/dts/rockchip/rk3399-gru-scarlet.dtsi | 46 ++++++++++++-------
> > arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi | 13 ------
> > 3 files changed, 42 insertions(+), 30 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
> > index c400be64170e..931640e9aed4 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
> > @@ -200,6 +200,19 @@
> > pinctrl-0 = <&bl_en>;
> > pwm-delay-us = <10000>;
> > };
> > +
> > + gpio_keys: gpio-keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&bt_host_wake_l>;
> > +
> > + wake_on_bt: wake-on-bt {
> > + label = "Wake-on-Bluetooth";
> > + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_WAKEUP>;
> > + wakeup-source;
> > + };
> > + };
> > };
> >
> > &ppvar_bigcpu {
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
> > index fc50b3ef758c..3e2196c08473 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
> > @@ -175,6 +175,21 @@
> > pinctrl-0 = <&dmic_en>;
> > wakeup-delay-ms = <250>;
> > };
> > +
> > + gpio_keys: gpio-keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pen_eject_odl>;
> > +
> > + pen-insert {
> > + label = "Pen Insert";
> > + /* Insert = low, eject = high */
> > + gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> > + linux,code = <SW_PEN_INSERTED>;
> > + linux,input-type = <EV_SW>;
> > + wakeup-source;
> > + };
> > + };
> > };
> >
> > /* pp900_s0 aliases */
> > @@ -328,20 +343,6 @@ camera: &i2c7 {
> > <400000000>;
> > };
> >
> > -&gpio_keys {
> > - pinctrl-names = "default";
> > - pinctrl-0 = <&bt_host_wake_l>, <&pen_eject_odl>;
> > -
> > - pen-insert {
> > - label = "Pen Insert";
> > - /* Insert = low, eject = high */
> > - gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> > - linux,code = <SW_PEN_INSERTED>;
> > - linux,input-type = <EV_SW>;
> > - wakeup-source;
> > - };
> > -};
> > -
> > &i2c_tunnel {
> > google,remote-bus = <0>;
> > };
> > @@ -437,8 +438,19 @@ camera: &i2c7 {
> > status = "okay";
> > };
> >
> > -&wake_on_bt {
> > - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
> > +&usb_host0_ohci {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + qca_bt: bt@1 {
> > + compatible = "usb0cf3,e300", "usb04ca,301a";
> > + reg = <1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&bt_host_wake_l>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "wakeup";
> > + };
> > };
>
> I didn't know it was possible to configure (certain) USB devices
> through the DT, neat!
>
> >
> > /* PINCTRL OVERRIDES */
> > @@ -455,7 +467,7 @@ camera: &i2c7 {
> > };
> >
> > &bt_host_wake_l {
> > - rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_up>;
> > + rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_none>;
> > };
> >
> > &ec_ap_int_l {
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> > index ea607a601a86..da03fa9c5662 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> > @@ -269,19 +269,6 @@
> > #clock-cells = <0>;
> > };
> >
> > - gpio_keys: gpio-keys {
> > - compatible = "gpio-keys";
> > - pinctrl-names = "default";
> > - pinctrl-0 = <&bt_host_wake_l>;
> > -
> > - wake_on_bt: wake-on-bt {
> > - label = "Wake-on-Bluetooth";
> > - gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
> > - linux,code = <KEY_WAKEUP>;
> > - wakeup-source;
> > - };
> > - };
> > -
> > max98357a: max98357a {
> > compatible = "maxim,max98357a";
> > pinctrl-names = "default";
>
> Reviewed-by: Matthias Kaehlcke <[email protected]>