Hi Abhishek,
> When scheduling TX packets, send all SCO/eSCO packets first and then
> send only 1 ACL/LE packet in a loop while checking that there are no SCO
> packets pending. This is done to make sure that we can meet SCO
> deadlines on slow interfaces like UART. If we were to queue up multiple
> ACL packets without checking for a SCO packet, we might miss the SCO
> timing. For example:
>
> The time it takes to send a maximum size ACL packet (1024 bytes):
> t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
> where 10/8 is uart overhead due to start/stop bits per byte
>
> Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666
> and is pretty close to a common baudrate of 3000000 used for BT. At this
> baudrate, if we sent two 1024 byte ACL packets, we would miss the 3.75ms
> timing window.
>
> Signed-off-by: Abhishek Pandit-Subedi <[email protected]>
> ---
>
> include/net/bluetooth/hci_core.h | 1 +
> net/bluetooth/hci_core.c | 91 +++++++++++++++++++++++++-------
> 2 files changed, 73 insertions(+), 19 deletions(-)
>
> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
> index d4e28773d378..f636c89f1fe1 100644
> --- a/include/net/bluetooth/hci_core.h
> +++ b/include/net/bluetooth/hci_core.h
> @@ -315,6 +315,7 @@ struct hci_dev {
> __u8 ssp_debug_mode;
> __u8 hw_error_code;
> __u32 clock;
> + __u8 sched_limit;
why do you need this parameter?
>
> __u16 devid_source;
> __u16 devid_vendor;
> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> index dbd2ad3a26ed..00a72265cd96 100644
> --- a/net/bluetooth/hci_core.c
> +++ b/net/bluetooth/hci_core.c
> @@ -4239,18 +4239,32 @@ static void __check_timeout(struct hci_dev *hdev, unsigned int cnt)
> }
> }
>
> -static void hci_sched_acl_pkt(struct hci_dev *hdev)
> +/* Limit packets in flight when SCO/eSCO links are active. */
> +static bool hci_sched_limit(struct hci_dev *hdev)
> +{
> + return hdev->sched_limit && hci_conn_num(hdev, SCO_LINK);
> +}
> +
> +static bool hci_sched_acl_pkt(struct hci_dev *hdev)
> {
> unsigned int cnt = hdev->acl_cnt;
> struct hci_chan *chan;
> struct sk_buff *skb;
> int quote;
> + bool sched_limit = hci_sched_limit(hdev);
> + bool resched = false;
>
> __check_timeout(hdev, cnt);
>
> while (hdev->acl_cnt &&
> (chan = hci_chan_sent(hdev, ACL_LINK, "e))) {
> u32 priority = (skb_peek(&chan->data_q))->priority;
> +
> + if (sched_limit && quote > 0) {
> + resched = true;
> + quote = 1;
> + }
> +
> while (quote-- && (skb = skb_peek(&chan->data_q))) {
> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
> skb->len, skb->priority);
> @@ -4271,19 +4285,26 @@ static void hci_sched_acl_pkt(struct hci_dev *hdev)
> chan->sent++;
> chan->conn->sent++;
> }
> +
> + if (resched && cnt != hdev->acl_cnt)
> + break;
> }
>
> - if (cnt != hdev->acl_cnt)
> + if (hdev->acl_cnt == 0 && cnt != hdev->acl_cnt)
> hci_prio_recalculate(hdev, ACL_LINK);
> +
> + return resched;
> }
>
> -static void hci_sched_acl_blk(struct hci_dev *hdev)
> +static bool hci_sched_acl_blk(struct hci_dev *hdev)
> {
> unsigned int cnt = hdev->block_cnt;
> struct hci_chan *chan;
> struct sk_buff *skb;
> int quote;
> u8 type;
> + bool sched_limit = hci_sched_limit(hdev);
> + bool resched = false;
>
> __check_timeout(hdev, cnt);
>
> @@ -4297,6 +4318,12 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> while (hdev->block_cnt > 0 &&
> (chan = hci_chan_sent(hdev, type, "e))) {
> u32 priority = (skb_peek(&chan->data_q))->priority;
> +
> + if (sched_limit && quote > 0) {
> + resched = true;
> + quote = 1;
> + }
> +
> while (quote > 0 && (skb = skb_peek(&chan->data_q))) {
> int blocks;
>
> @@ -4311,7 +4338,7 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>
> blocks = __get_blocks(hdev, skb);
> if (blocks > hdev->block_cnt)
> - return;
> + return false;
>
> hci_conn_enter_active_mode(chan->conn,
> bt_cb(skb)->force_active);
> @@ -4325,33 +4352,39 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> chan->sent += blocks;
> chan->conn->sent += blocks;
> }
> +
> + if (resched && cnt != hdev->block_cnt)
> + break;
> }
>
> - if (cnt != hdev->block_cnt)
> + if (hdev->block_cnt == 0 && cnt != hdev->block_cnt)
> hci_prio_recalculate(hdev, type);
> +
> + return resched;
> }
>
> -static void hci_sched_acl(struct hci_dev *hdev)
> +static bool hci_sched_acl(struct hci_dev *hdev)
> {
> BT_DBG("%s", hdev->name);
>
> /* No ACL link over BR/EDR controller */
> if (!hci_conn_num(hdev, ACL_LINK) && hdev->dev_type == HCI_PRIMARY)
> - return;
> + goto done;
Style wise the goto done is overkill. Just return false.
>
> /* No AMP link over AMP controller */
> if (!hci_conn_num(hdev, AMP_LINK) && hdev->dev_type == HCI_AMP)
> - return;
> + goto done;
>
> switch (hdev->flow_ctl_mode) {
> case HCI_FLOW_CTL_MODE_PACKET_BASED:
> - hci_sched_acl_pkt(hdev);
> - break;
> + return hci_sched_acl_pkt(hdev);
>
> case HCI_FLOW_CTL_MODE_BLOCK_BASED:
> - hci_sched_acl_blk(hdev);
> - break;
> + return hci_sched_acl_blk(hdev);
So the block based mode is for AMP controllers and not used on BR/EDR controllers. Since AMP controllers only transport ACL packet and no SCO/eSCO packets, we can ignore this here.
> }
> +
> +done:
> + return false;
> }
>
> /* Schedule SCO */
> @@ -4402,16 +4435,18 @@ static void hci_sched_esco(struct hci_dev *hdev)
> }
> }
>
> -static void hci_sched_le(struct hci_dev *hdev)
> +static bool hci_sched_le(struct hci_dev *hdev)
> {
> struct hci_chan *chan;
> struct sk_buff *skb;
> int quote, cnt, tmp;
> + bool sched_limit = hci_sched_limit(hdev);
> + bool resched = false;
>
> BT_DBG("%s", hdev->name);
>
> if (!hci_conn_num(hdev, LE_LINK))
> - return;
> + return resched;
>
> cnt = hdev->le_pkts ? hdev->le_cnt : hdev->acl_cnt;
>
> @@ -4420,6 +4455,12 @@ static void hci_sched_le(struct hci_dev *hdev)
> tmp = cnt;
> while (cnt && (chan = hci_chan_sent(hdev, LE_LINK, "e))) {
> u32 priority = (skb_peek(&chan->data_q))->priority;
> +
> + if (sched_limit && quote > 0) {
> + resched = true;
> + quote = 1;
> + }
> +
> while (quote-- && (skb = skb_peek(&chan->data_q))) {
> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
> skb->len, skb->priority);
> @@ -4437,6 +4478,9 @@ static void hci_sched_le(struct hci_dev *hdev)
> chan->sent++;
> chan->conn->sent++;
> }
> +
> + if (resched && cnt != tmp)
> + break;
> }
>
> if (hdev->le_pkts)
> @@ -4444,24 +4488,33 @@ static void hci_sched_le(struct hci_dev *hdev)
> else
> hdev->acl_cnt = cnt;
>
> - if (cnt != tmp)
> + if (cnt == 0 && cnt != tmp)
> hci_prio_recalculate(hdev, LE_LINK);
> +
> + return resched;
> }
>
> static void hci_tx_work(struct work_struct *work)
> {
> struct hci_dev *hdev = container_of(work, struct hci_dev, tx_work);
> struct sk_buff *skb;
> + bool resched;
>
> BT_DBG("%s acl %d sco %d le %d", hdev->name, hdev->acl_cnt,
> hdev->sco_cnt, hdev->le_cnt);
>
> if (!hci_dev_test_flag(hdev, HCI_USER_CHANNEL)) {
> /* Schedule queues and send stuff to HCI driver */
> - hci_sched_acl(hdev);
> - hci_sched_sco(hdev);
> - hci_sched_esco(hdev);
> - hci_sched_le(hdev);
> + do {
> + /* SCO and eSCO send all packets until emptied */
> + hci_sched_sco(hdev);
> + hci_sched_esco(hdev);
> +
> + /* Acl and Le send based on quota (priority on ACL per
> + * loop)
> + */
> + resched = hci_sched_acl(hdev) || hci_sched_le(hdev);
> + } while (resched);
> }
I am not in favor of this busy loop. We might want to re-think the whole scheduling by connection type and really only focus on scheduling ACL (BR/EDR and LE) and audio packets (SCO/eSCO and ISO).
In addition, we also need to check that SCO scheduling and A2DP media channel ACL packets do work together. I think that generally it would be best to have a clear rate at which SCO packets are require to pushed down to the hardware. So you really reserve bandwidth and not blindly prioritize them via a busy loop.
Regards
Marcel
Hi Marcel,
On Fri, Mar 13, 2020 at 12:01 PM Marcel Holtmann <[email protected]> wrote:
>
> Hi Abhishek,
>
> > When scheduling TX packets, send all SCO/eSCO packets first and then
> > send only 1 ACL/LE packet in a loop while checking that there are no SCO
> > packets pending. This is done to make sure that we can meet SCO
> > deadlines on slow interfaces like UART. If we were to queue up multiple
> > ACL packets without checking for a SCO packet, we might miss the SCO
> > timing. For example:
> >
> > The time it takes to send a maximum size ACL packet (1024 bytes):
> > t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
> > where 10/8 is uart overhead due to start/stop bits per byte
> >
> > Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666
> > and is pretty close to a common baudrate of 3000000 used for BT. At this
> > baudrate, if we sent two 1024 byte ACL packets, we would miss the 3.75ms
> > timing window.
> >
> > Signed-off-by: Abhishek Pandit-Subedi <[email protected]>
> > ---
> >
> > include/net/bluetooth/hci_core.h | 1 +
> > net/bluetooth/hci_core.c | 91 +++++++++++++++++++++++++-------
> > 2 files changed, 73 insertions(+), 19 deletions(-)
> >
> > diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
> > index d4e28773d378..f636c89f1fe1 100644
> > --- a/include/net/bluetooth/hci_core.h
> > +++ b/include/net/bluetooth/hci_core.h
> > @@ -315,6 +315,7 @@ struct hci_dev {
> > __u8 ssp_debug_mode;
> > __u8 hw_error_code;
> > __u32 clock;
> > + __u8 sched_limit;
>
> why do you need this parameter?
This is really only necessary on systems where the data transfer rate
to the controller is low. I want the driver to set whether we should
aggressively schedule SCO packets. A quirk might actually be better
than a variable (wasn't sure what is preferable).
>
> >
> > __u16 devid_source;
> > __u16 devid_vendor;
> > diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> > index dbd2ad3a26ed..00a72265cd96 100644
> > --- a/net/bluetooth/hci_core.c
> > +++ b/net/bluetooth/hci_core.c
> > @@ -4239,18 +4239,32 @@ static void __check_timeout(struct hci_dev *hdev, unsigned int cnt)
> > }
> > }
> >
> > -static void hci_sched_acl_pkt(struct hci_dev *hdev)
> > +/* Limit packets in flight when SCO/eSCO links are active. */
> > +static bool hci_sched_limit(struct hci_dev *hdev)
> > +{
> > + return hdev->sched_limit && hci_conn_num(hdev, SCO_LINK);
> > +}
> > +
> > +static bool hci_sched_acl_pkt(struct hci_dev *hdev)
> > {
> > unsigned int cnt = hdev->acl_cnt;
> > struct hci_chan *chan;
> > struct sk_buff *skb;
> > int quote;
> > + bool sched_limit = hci_sched_limit(hdev);
> > + bool resched = false;
> >
> > __check_timeout(hdev, cnt);
> >
> > while (hdev->acl_cnt &&
> > (chan = hci_chan_sent(hdev, ACL_LINK, "e))) {
> > u32 priority = (skb_peek(&chan->data_q))->priority;
> > +
> > + if (sched_limit && quote > 0) {
> > + resched = true;
> > + quote = 1;
> > + }
> > +
> > while (quote-- && (skb = skb_peek(&chan->data_q))) {
> > BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
> > skb->len, skb->priority);
> > @@ -4271,19 +4285,26 @@ static void hci_sched_acl_pkt(struct hci_dev *hdev)
> > chan->sent++;
> > chan->conn->sent++;
> > }
> > +
> > + if (resched && cnt != hdev->acl_cnt)
> > + break;
> > }
> >
> > - if (cnt != hdev->acl_cnt)
> > + if (hdev->acl_cnt == 0 && cnt != hdev->acl_cnt)
> > hci_prio_recalculate(hdev, ACL_LINK);
> > +
> > + return resched;
> > }
> >
> > -static void hci_sched_acl_blk(struct hci_dev *hdev)
> > +static bool hci_sched_acl_blk(struct hci_dev *hdev)
> > {
> > unsigned int cnt = hdev->block_cnt;
> > struct hci_chan *chan;
> > struct sk_buff *skb;
> > int quote;
> > u8 type;
> > + bool sched_limit = hci_sched_limit(hdev);
> > + bool resched = false;
> >
> > __check_timeout(hdev, cnt);
> >
> > @@ -4297,6 +4318,12 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> > while (hdev->block_cnt > 0 &&
> > (chan = hci_chan_sent(hdev, type, "e))) {
> > u32 priority = (skb_peek(&chan->data_q))->priority;
> > +
> > + if (sched_limit && quote > 0) {
> > + resched = true;
> > + quote = 1;
> > + }
> > +
> > while (quote > 0 && (skb = skb_peek(&chan->data_q))) {
> > int blocks;
> >
> > @@ -4311,7 +4338,7 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> >
> > blocks = __get_blocks(hdev, skb);
> > if (blocks > hdev->block_cnt)
> > - return;
> > + return false;
> >
> > hci_conn_enter_active_mode(chan->conn,
> > bt_cb(skb)->force_active);
> > @@ -4325,33 +4352,39 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> > chan->sent += blocks;
> > chan->conn->sent += blocks;
> > }
> > +
> > + if (resched && cnt != hdev->block_cnt)
> > + break;
> > }
> >
> > - if (cnt != hdev->block_cnt)
> > + if (hdev->block_cnt == 0 && cnt != hdev->block_cnt)
> > hci_prio_recalculate(hdev, type);
> > +
> > + return resched;
> > }
> >
> > -static void hci_sched_acl(struct hci_dev *hdev)
> > +static bool hci_sched_acl(struct hci_dev *hdev)
> > {
> > BT_DBG("%s", hdev->name);
> >
> > /* No ACL link over BR/EDR controller */
> > if (!hci_conn_num(hdev, ACL_LINK) && hdev->dev_type == HCI_PRIMARY)
> > - return;
> > + goto done;
>
> Style wise the goto done is overkill. Just return false.
Will do.
>
> >
> > /* No AMP link over AMP controller */
> > if (!hci_conn_num(hdev, AMP_LINK) && hdev->dev_type == HCI_AMP)
> > - return;
> > + goto done;
> >
> > switch (hdev->flow_ctl_mode) {
> > case HCI_FLOW_CTL_MODE_PACKET_BASED:
> > - hci_sched_acl_pkt(hdev);
> > - break;
> > + return hci_sched_acl_pkt(hdev);
> >
> > case HCI_FLOW_CTL_MODE_BLOCK_BASED:
> > - hci_sched_acl_blk(hdev);
> > - break;
> > + return hci_sched_acl_blk(hdev);
>
> So the block based mode is for AMP controllers and not used on BR/EDR controllers. Since AMP controllers only transport ACL packet and no SCO/eSCO packets, we can ignore this here.
Ok, I'll remove it there.
>
> > }
> > +
> > +done:
> > + return false;
> > }
> >
> > /* Schedule SCO */
> > @@ -4402,16 +4435,18 @@ static void hci_sched_esco(struct hci_dev *hdev)
> > }
> > }
> >
> > -static void hci_sched_le(struct hci_dev *hdev)
> > +static bool hci_sched_le(struct hci_dev *hdev)
> > {
> > struct hci_chan *chan;
> > struct sk_buff *skb;
> > int quote, cnt, tmp;
> > + bool sched_limit = hci_sched_limit(hdev);
> > + bool resched = false;
> >
> > BT_DBG("%s", hdev->name);
> >
> > if (!hci_conn_num(hdev, LE_LINK))
> > - return;
> > + return resched;
> >
> > cnt = hdev->le_pkts ? hdev->le_cnt : hdev->acl_cnt;
> >
> > @@ -4420,6 +4455,12 @@ static void hci_sched_le(struct hci_dev *hdev)
> > tmp = cnt;
> > while (cnt && (chan = hci_chan_sent(hdev, LE_LINK, "e))) {
> > u32 priority = (skb_peek(&chan->data_q))->priority;
> > +
> > + if (sched_limit && quote > 0) {
> > + resched = true;
> > + quote = 1;
> > + }
> > +
> > while (quote-- && (skb = skb_peek(&chan->data_q))) {
> > BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
> > skb->len, skb->priority);
> > @@ -4437,6 +4478,9 @@ static void hci_sched_le(struct hci_dev *hdev)
> > chan->sent++;
> > chan->conn->sent++;
> > }
> > +
> > + if (resched && cnt != tmp)
> > + break;
> > }
> >
> > if (hdev->le_pkts)
> > @@ -4444,24 +4488,33 @@ static void hci_sched_le(struct hci_dev *hdev)
> > else
> > hdev->acl_cnt = cnt;
> >
> > - if (cnt != tmp)
> > + if (cnt == 0 && cnt != tmp)
> > hci_prio_recalculate(hdev, LE_LINK);
> > +
> > + return resched;
> > }
> >
> > static void hci_tx_work(struct work_struct *work)
> > {
> > struct hci_dev *hdev = container_of(work, struct hci_dev, tx_work);
> > struct sk_buff *skb;
> > + bool resched;
> >
> > BT_DBG("%s acl %d sco %d le %d", hdev->name, hdev->acl_cnt,
> > hdev->sco_cnt, hdev->le_cnt);
> >
> > if (!hci_dev_test_flag(hdev, HCI_USER_CHANNEL)) {
> > /* Schedule queues and send stuff to HCI driver */
> > - hci_sched_acl(hdev);
> > - hci_sched_sco(hdev);
> > - hci_sched_esco(hdev);
> > - hci_sched_le(hdev);
> > + do {
> > + /* SCO and eSCO send all packets until emptied */
> > + hci_sched_sco(hdev);
> > + hci_sched_esco(hdev);
> > +
> > + /* Acl and Le send based on quota (priority on ACL per
> > + * loop)
> > + */
> > + resched = hci_sched_acl(hdev) || hci_sched_le(hdev);
> > + } while (resched);
> > }
>
> I am not in favor of this busy loop. We might want to re-think the whole scheduling by connection type and really only focus on scheduling ACL (BR/EDR and LE) and audio packets (SCO/eSCO and ISO).
I think the busy loop is the simplest solution if we want to solve the
problem: don't send 2 ACL packets without checking if there is a SCO
packet scheduled (which is the worst case I'm worried about on UART
interfaces).
If we get rid of the connection type scheduling and only do audio and
ACL, we would still need some mechanism to guarantee that you don't
send >~1100 bytes without checking if SCO is queued (assuming 3000000
baudrate and 3.75ms latency requirement).
>
> In addition, we also need to check that SCO scheduling and A2DP media channel ACL packets do work together. I think that generally it would be best to have a clear rate at which SCO packets are require to pushed down to the hardware. So you really reserve bandwidth and not blindly prioritize them via a busy loop.
>
I am less worried about bandwidth and more about latency. If I start
sending really large ACL packets through UART, it could take multiple
milliseconds. It really has to be reserved bandwidth per small
timeslice (like 3.75ms) so I can guarantee that if a SCO packet is
seen within that time slice, it will be transferred. There will still
have to be a busy loop though because the amount of data you can send
in the time slice will probably be less than the data that can be
in-flight to the controller (i.e. acl_max_pkts).
> Regards
>
> Marcel
>
Thanks,
Abhishek
Hi Abhishek,
>>> When scheduling TX packets, send all SCO/eSCO packets first and then
>>> send only 1 ACL/LE packet in a loop while checking that there are no SCO
>>> packets pending. This is done to make sure that we can meet SCO
>>> deadlines on slow interfaces like UART. If we were to queue up multiple
>>> ACL packets without checking for a SCO packet, we might miss the SCO
>>> timing. For example:
>>>
>>> The time it takes to send a maximum size ACL packet (1024 bytes):
>>> t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
>>> where 10/8 is uart overhead due to start/stop bits per byte
>>>
>>> Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666
>>> and is pretty close to a common baudrate of 3000000 used for BT. At this
>>> baudrate, if we sent two 1024 byte ACL packets, we would miss the 3.75ms
>>> timing window.
>>>
>>> Signed-off-by: Abhishek Pandit-Subedi <[email protected]>
>>> ---
>>>
>>> include/net/bluetooth/hci_core.h | 1 +
>>> net/bluetooth/hci_core.c | 91 +++++++++++++++++++++++++-------
>>> 2 files changed, 73 insertions(+), 19 deletions(-)
>>>
>>> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
>>> index d4e28773d378..f636c89f1fe1 100644
>>> --- a/include/net/bluetooth/hci_core.h
>>> +++ b/include/net/bluetooth/hci_core.h
>>> @@ -315,6 +315,7 @@ struct hci_dev {
>>> __u8 ssp_debug_mode;
>>> __u8 hw_error_code;
>>> __u32 clock;
>>> + __u8 sched_limit;
>>
>> why do you need this parameter?
>
> This is really only necessary on systems where the data transfer rate
> to the controller is low. I want the driver to set whether we should
> aggressively schedule SCO packets. A quirk might actually be better
> than a variable (wasn't sure what is preferable).
or maybe we try without driver choice first. I would assume what is required for UART, will not harm USB or SDIO transports either.
>>> __u16 devid_source;
>>> __u16 devid_vendor;
>>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
>>> index dbd2ad3a26ed..00a72265cd96 100644
>>> --- a/net/bluetooth/hci_core.c
>>> +++ b/net/bluetooth/hci_core.c
>>> @@ -4239,18 +4239,32 @@ static void __check_timeout(struct hci_dev *hdev, unsigned int cnt)
>>> }
>>> }
>>>
>>> -static void hci_sched_acl_pkt(struct hci_dev *hdev)
>>> +/* Limit packets in flight when SCO/eSCO links are active. */
>>> +static bool hci_sched_limit(struct hci_dev *hdev)
>>> +{
>>> + return hdev->sched_limit && hci_conn_num(hdev, SCO_LINK);
>>> +}
>>> +
>>> +static bool hci_sched_acl_pkt(struct hci_dev *hdev)
>>> {
>>> unsigned int cnt = hdev->acl_cnt;
>>> struct hci_chan *chan;
>>> struct sk_buff *skb;
>>> int quote;
>>> + bool sched_limit = hci_sched_limit(hdev);
>>> + bool resched = false;
>>>
>>> __check_timeout(hdev, cnt);
>>>
>>> while (hdev->acl_cnt &&
>>> (chan = hci_chan_sent(hdev, ACL_LINK, "e))) {
>>> u32 priority = (skb_peek(&chan->data_q))->priority;
>>> +
>>> + if (sched_limit && quote > 0) {
>>> + resched = true;
>>> + quote = 1;
>>> + }
>>> +
>>> while (quote-- && (skb = skb_peek(&chan->data_q))) {
>>> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
>>> skb->len, skb->priority);
>>> @@ -4271,19 +4285,26 @@ static void hci_sched_acl_pkt(struct hci_dev *hdev)
>>> chan->sent++;
>>> chan->conn->sent++;
>>> }
>>> +
>>> + if (resched && cnt != hdev->acl_cnt)
>>> + break;
>>> }
>>>
>>> - if (cnt != hdev->acl_cnt)
>>> + if (hdev->acl_cnt == 0 && cnt != hdev->acl_cnt)
>>> hci_prio_recalculate(hdev, ACL_LINK);
>>> +
>>> + return resched;
>>> }
>>>
>>> -static void hci_sched_acl_blk(struct hci_dev *hdev)
>>> +static bool hci_sched_acl_blk(struct hci_dev *hdev)
>>> {
>>> unsigned int cnt = hdev->block_cnt;
>>> struct hci_chan *chan;
>>> struct sk_buff *skb;
>>> int quote;
>>> u8 type;
>>> + bool sched_limit = hci_sched_limit(hdev);
>>> + bool resched = false;
>>>
>>> __check_timeout(hdev, cnt);
>>>
>>> @@ -4297,6 +4318,12 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>>> while (hdev->block_cnt > 0 &&
>>> (chan = hci_chan_sent(hdev, type, "e))) {
>>> u32 priority = (skb_peek(&chan->data_q))->priority;
>>> +
>>> + if (sched_limit && quote > 0) {
>>> + resched = true;
>>> + quote = 1;
>>> + }
>>> +
>>> while (quote > 0 && (skb = skb_peek(&chan->data_q))) {
>>> int blocks;
>>>
>>> @@ -4311,7 +4338,7 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>>>
>>> blocks = __get_blocks(hdev, skb);
>>> if (blocks > hdev->block_cnt)
>>> - return;
>>> + return false;
>>>
>>> hci_conn_enter_active_mode(chan->conn,
>>> bt_cb(skb)->force_active);
>>> @@ -4325,33 +4352,39 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>>> chan->sent += blocks;
>>> chan->conn->sent += blocks;
>>> }
>>> +
>>> + if (resched && cnt != hdev->block_cnt)
>>> + break;
>>> }
>>>
>>> - if (cnt != hdev->block_cnt)
>>> + if (hdev->block_cnt == 0 && cnt != hdev->block_cnt)
>>> hci_prio_recalculate(hdev, type);
>>> +
>>> + return resched;
>>> }
>>>
>>> -static void hci_sched_acl(struct hci_dev *hdev)
>>> +static bool hci_sched_acl(struct hci_dev *hdev)
>>> {
>>> BT_DBG("%s", hdev->name);
>>>
>>> /* No ACL link over BR/EDR controller */
>>> if (!hci_conn_num(hdev, ACL_LINK) && hdev->dev_type == HCI_PRIMARY)
>>> - return;
>>> + goto done;
>>
>> Style wise the goto done is overkill. Just return false.
>
> Will do.
>
>>
>>>
>>> /* No AMP link over AMP controller */
>>> if (!hci_conn_num(hdev, AMP_LINK) && hdev->dev_type == HCI_AMP)
>>> - return;
>>> + goto done;
>>>
>>> switch (hdev->flow_ctl_mode) {
>>> case HCI_FLOW_CTL_MODE_PACKET_BASED:
>>> - hci_sched_acl_pkt(hdev);
>>> - break;
>>> + return hci_sched_acl_pkt(hdev);
>>>
>>> case HCI_FLOW_CTL_MODE_BLOCK_BASED:
>>> - hci_sched_acl_blk(hdev);
>>> - break;
>>> + return hci_sched_acl_blk(hdev);
>>
>> So the block based mode is for AMP controllers and not used on BR/EDR controllers. Since AMP controllers only transport ACL packet and no SCO/eSCO packets, we can ignore this here.
>
> Ok, I'll remove it there.
>
>>
>>> }
>>> +
>>> +done:
>>> + return false;
>>> }
>>>
>>> /* Schedule SCO */
>>> @@ -4402,16 +4435,18 @@ static void hci_sched_esco(struct hci_dev *hdev)
>>> }
>>> }
>>>
>>> -static void hci_sched_le(struct hci_dev *hdev)
>>> +static bool hci_sched_le(struct hci_dev *hdev)
>>> {
>>> struct hci_chan *chan;
>>> struct sk_buff *skb;
>>> int quote, cnt, tmp;
>>> + bool sched_limit = hci_sched_limit(hdev);
>>> + bool resched = false;
>>>
>>> BT_DBG("%s", hdev->name);
>>>
>>> if (!hci_conn_num(hdev, LE_LINK))
>>> - return;
>>> + return resched;
>>>
>>> cnt = hdev->le_pkts ? hdev->le_cnt : hdev->acl_cnt;
>>>
>>> @@ -4420,6 +4455,12 @@ static void hci_sched_le(struct hci_dev *hdev)
>>> tmp = cnt;
>>> while (cnt && (chan = hci_chan_sent(hdev, LE_LINK, "e))) {
>>> u32 priority = (skb_peek(&chan->data_q))->priority;
>>> +
>>> + if (sched_limit && quote > 0) {
>>> + resched = true;
>>> + quote = 1;
>>> + }
>>> +
>>> while (quote-- && (skb = skb_peek(&chan->data_q))) {
>>> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
>>> skb->len, skb->priority);
>>> @@ -4437,6 +4478,9 @@ static void hci_sched_le(struct hci_dev *hdev)
>>> chan->sent++;
>>> chan->conn->sent++;
>>> }
>>> +
>>> + if (resched && cnt != tmp)
>>> + break;
>>> }
>>>
>>> if (hdev->le_pkts)
>>> @@ -4444,24 +4488,33 @@ static void hci_sched_le(struct hci_dev *hdev)
>>> else
>>> hdev->acl_cnt = cnt;
>>>
>>> - if (cnt != tmp)
>>> + if (cnt == 0 && cnt != tmp)
>>> hci_prio_recalculate(hdev, LE_LINK);
>>> +
>>> + return resched;
>>> }
>>>
>>> static void hci_tx_work(struct work_struct *work)
>>> {
>>> struct hci_dev *hdev = container_of(work, struct hci_dev, tx_work);
>>> struct sk_buff *skb;
>>> + bool resched;
>>>
>>> BT_DBG("%s acl %d sco %d le %d", hdev->name, hdev->acl_cnt,
>>> hdev->sco_cnt, hdev->le_cnt);
>>>
>>> if (!hci_dev_test_flag(hdev, HCI_USER_CHANNEL)) {
>>> /* Schedule queues and send stuff to HCI driver */
>>> - hci_sched_acl(hdev);
>>> - hci_sched_sco(hdev);
>>> - hci_sched_esco(hdev);
>>> - hci_sched_le(hdev);
>>> + do {
>>> + /* SCO and eSCO send all packets until emptied */
>>> + hci_sched_sco(hdev);
>>> + hci_sched_esco(hdev);
>>> +
>>> + /* Acl and Le send based on quota (priority on ACL per
>>> + * loop)
>>> + */
>>> + resched = hci_sched_acl(hdev) || hci_sched_le(hdev);
>>> + } while (resched);
>>> }
>>
>> I am not in favor of this busy loop. We might want to re-think the whole scheduling by connection type and really only focus on scheduling ACL (BR/EDR and LE) and audio packets (SCO/eSCO and ISO).
>
> I think the busy loop is the simplest solution if we want to solve the
> problem: don't send 2 ACL packets without checking if there is a SCO
> packet scheduled (which is the worst case I'm worried about on UART
> interfaces).
>
> If we get rid of the connection type scheduling and only do audio and
> ACL, we would still need some mechanism to guarantee that you don't
> send >~1100 bytes without checking if SCO is queued (assuming 3000000
> baudrate and 3.75ms latency requirement).
Why don’t we just say that if SCO is queued up, then after each ACL packet we should send a SCO packet.
>
>>
>> In addition, we also need to check that SCO scheduling and A2DP media channel ACL packets do work together. I think that generally it would be best to have a clear rate at which SCO packets are require to pushed down to the hardware. So you really reserve bandwidth and not blindly prioritize them via a busy loop.
>>
> I am less worried about bandwidth and more about latency. If I start
> sending really large ACL packets through UART, it could take multiple
> milliseconds. It really has to be reserved bandwidth per small
> timeslice (like 3.75ms) so I can guarantee that if a SCO packet is
> seen within that time slice, it will be transferred. There will still
> have to be a busy loop though because the amount of data you can send
> in the time slice will probably be less than the data that can be
> in-flight to the controller (i.e. acl_max_pkts).
Right now we kinda let the SCO socket application provide the correct timing. I was thinking that the kernel might need to enforce this.
Regards
Marcel
On Wed, Mar 18, 2020 at 10:11 AM Marcel Holtmann <[email protected]> wrote:
>
> Hi Abhishek,
>
> >>> When scheduling TX packets, send all SCO/eSCO packets first and then
> >>> send only 1 ACL/LE packet in a loop while checking that there are no SCO
> >>> packets pending. This is done to make sure that we can meet SCO
> >>> deadlines on slow interfaces like UART. If we were to queue up multiple
> >>> ACL packets without checking for a SCO packet, we might miss the SCO
> >>> timing. For example:
> >>>
> >>> The time it takes to send a maximum size ACL packet (1024 bytes):
> >>> t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
> >>> where 10/8 is uart overhead due to start/stop bits per byte
> >>>
> >>> Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666
> >>> and is pretty close to a common baudrate of 3000000 used for BT. At this
> >>> baudrate, if we sent two 1024 byte ACL packets, we would miss the 3.75ms
> >>> timing window.
> >>>
> >>> Signed-off-by: Abhishek Pandit-Subedi <[email protected]>
> >>> ---
> >>>
> >>> include/net/bluetooth/hci_core.h | 1 +
> >>> net/bluetooth/hci_core.c | 91 +++++++++++++++++++++++++-------
> >>> 2 files changed, 73 insertions(+), 19 deletions(-)
> >>>
> >>> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
> >>> index d4e28773d378..f636c89f1fe1 100644
> >>> --- a/include/net/bluetooth/hci_core.h
> >>> +++ b/include/net/bluetooth/hci_core.h
> >>> @@ -315,6 +315,7 @@ struct hci_dev {
> >>> __u8 ssp_debug_mode;
> >>> __u8 hw_error_code;
> >>> __u32 clock;
> >>> + __u8 sched_limit;
> >>
> >> why do you need this parameter?
> >
> > This is really only necessary on systems where the data transfer rate
> > to the controller is low. I want the driver to set whether we should
> > aggressively schedule SCO packets. A quirk might actually be better
> > than a variable (wasn't sure what is preferable).
>
> or maybe we try without driver choice first. I would assume what is required for UART, will not harm USB or SDIO transports either.
Ack -- I can make this default behavior.
>
> >>> __u16 devid_source;
> >>> __u16 devid_vendor;
> >>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
> >>> index dbd2ad3a26ed..00a72265cd96 100644
> >>> --- a/net/bluetooth/hci_core.c
> >>> +++ b/net/bluetooth/hci_core.c
> >>> @@ -4239,18 +4239,32 @@ static void __check_timeout(struct hci_dev *hdev, unsigned int cnt)
> >>> }
> >>> }
> >>>
> >>> -static void hci_sched_acl_pkt(struct hci_dev *hdev)
> >>> +/* Limit packets in flight when SCO/eSCO links are active. */
> >>> +static bool hci_sched_limit(struct hci_dev *hdev)
> >>> +{
> >>> + return hdev->sched_limit && hci_conn_num(hdev, SCO_LINK);
> >>> +}
> >>> +
> >>> +static bool hci_sched_acl_pkt(struct hci_dev *hdev)
> >>> {
> >>> unsigned int cnt = hdev->acl_cnt;
> >>> struct hci_chan *chan;
> >>> struct sk_buff *skb;
> >>> int quote;
> >>> + bool sched_limit = hci_sched_limit(hdev);
> >>> + bool resched = false;
> >>>
> >>> __check_timeout(hdev, cnt);
> >>>
> >>> while (hdev->acl_cnt &&
> >>> (chan = hci_chan_sent(hdev, ACL_LINK, "e))) {
> >>> u32 priority = (skb_peek(&chan->data_q))->priority;
> >>> +
> >>> + if (sched_limit && quote > 0) {
> >>> + resched = true;
> >>> + quote = 1;
> >>> + }
> >>> +
> >>> while (quote-- && (skb = skb_peek(&chan->data_q))) {
> >>> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
> >>> skb->len, skb->priority);
> >>> @@ -4271,19 +4285,26 @@ static void hci_sched_acl_pkt(struct hci_dev *hdev)
> >>> chan->sent++;
> >>> chan->conn->sent++;
> >>> }
> >>> +
> >>> + if (resched && cnt != hdev->acl_cnt)
> >>> + break;
> >>> }
> >>>
> >>> - if (cnt != hdev->acl_cnt)
> >>> + if (hdev->acl_cnt == 0 && cnt != hdev->acl_cnt)
> >>> hci_prio_recalculate(hdev, ACL_LINK);
> >>> +
> >>> + return resched;
> >>> }
> >>>
> >>> -static void hci_sched_acl_blk(struct hci_dev *hdev)
> >>> +static bool hci_sched_acl_blk(struct hci_dev *hdev)
> >>> {
> >>> unsigned int cnt = hdev->block_cnt;
> >>> struct hci_chan *chan;
> >>> struct sk_buff *skb;
> >>> int quote;
> >>> u8 type;
> >>> + bool sched_limit = hci_sched_limit(hdev);
> >>> + bool resched = false;
> >>>
> >>> __check_timeout(hdev, cnt);
> >>>
> >>> @@ -4297,6 +4318,12 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> >>> while (hdev->block_cnt > 0 &&
> >>> (chan = hci_chan_sent(hdev, type, "e))) {
> >>> u32 priority = (skb_peek(&chan->data_q))->priority;
> >>> +
> >>> + if (sched_limit && quote > 0) {
> >>> + resched = true;
> >>> + quote = 1;
> >>> + }
> >>> +
> >>> while (quote > 0 && (skb = skb_peek(&chan->data_q))) {
> >>> int blocks;
> >>>
> >>> @@ -4311,7 +4338,7 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> >>>
> >>> blocks = __get_blocks(hdev, skb);
> >>> if (blocks > hdev->block_cnt)
> >>> - return;
> >>> + return false;
> >>>
> >>> hci_conn_enter_active_mode(chan->conn,
> >>> bt_cb(skb)->force_active);
> >>> @@ -4325,33 +4352,39 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
> >>> chan->sent += blocks;
> >>> chan->conn->sent += blocks;
> >>> }
> >>> +
> >>> + if (resched && cnt != hdev->block_cnt)
> >>> + break;
> >>> }
> >>>
> >>> - if (cnt != hdev->block_cnt)
> >>> + if (hdev->block_cnt == 0 && cnt != hdev->block_cnt)
> >>> hci_prio_recalculate(hdev, type);
> >>> +
> >>> + return resched;
> >>> }
> >>>
> >>> -static void hci_sched_acl(struct hci_dev *hdev)
> >>> +static bool hci_sched_acl(struct hci_dev *hdev)
> >>> {
> >>> BT_DBG("%s", hdev->name);
> >>>
> >>> /* No ACL link over BR/EDR controller */
> >>> if (!hci_conn_num(hdev, ACL_LINK) && hdev->dev_type == HCI_PRIMARY)
> >>> - return;
> >>> + goto done;
> >>
> >> Style wise the goto done is overkill. Just return false.
> >
> > Will do.
> >
> >>
> >>>
> >>> /* No AMP link over AMP controller */
> >>> if (!hci_conn_num(hdev, AMP_LINK) && hdev->dev_type == HCI_AMP)
> >>> - return;
> >>> + goto done;
> >>>
> >>> switch (hdev->flow_ctl_mode) {
> >>> case HCI_FLOW_CTL_MODE_PACKET_BASED:
> >>> - hci_sched_acl_pkt(hdev);
> >>> - break;
> >>> + return hci_sched_acl_pkt(hdev);
> >>>
> >>> case HCI_FLOW_CTL_MODE_BLOCK_BASED:
> >>> - hci_sched_acl_blk(hdev);
> >>> - break;
> >>> + return hci_sched_acl_blk(hdev);
> >>
> >> So the block based mode is for AMP controllers and not used on BR/EDR controllers. Since AMP controllers only transport ACL packet and no SCO/eSCO packets, we can ignore this here.
> >
> > Ok, I'll remove it there.
> >
> >>
> >>> }
> >>> +
> >>> +done:
> >>> + return false;
> >>> }
> >>>
> >>> /* Schedule SCO */
> >>> @@ -4402,16 +4435,18 @@ static void hci_sched_esco(struct hci_dev *hdev)
> >>> }
> >>> }
> >>>
> >>> -static void hci_sched_le(struct hci_dev *hdev)
> >>> +static bool hci_sched_le(struct hci_dev *hdev)
> >>> {
> >>> struct hci_chan *chan;
> >>> struct sk_buff *skb;
> >>> int quote, cnt, tmp;
> >>> + bool sched_limit = hci_sched_limit(hdev);
> >>> + bool resched = false;
> >>>
> >>> BT_DBG("%s", hdev->name);
> >>>
> >>> if (!hci_conn_num(hdev, LE_LINK))
> >>> - return;
> >>> + return resched;
> >>>
> >>> cnt = hdev->le_pkts ? hdev->le_cnt : hdev->acl_cnt;
> >>>
> >>> @@ -4420,6 +4455,12 @@ static void hci_sched_le(struct hci_dev *hdev)
> >>> tmp = cnt;
> >>> while (cnt && (chan = hci_chan_sent(hdev, LE_LINK, "e))) {
> >>> u32 priority = (skb_peek(&chan->data_q))->priority;
> >>> +
> >>> + if (sched_limit && quote > 0) {
> >>> + resched = true;
> >>> + quote = 1;
> >>> + }
> >>> +
> >>> while (quote-- && (skb = skb_peek(&chan->data_q))) {
> >>> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
> >>> skb->len, skb->priority);
> >>> @@ -4437,6 +4478,9 @@ static void hci_sched_le(struct hci_dev *hdev)
> >>> chan->sent++;
> >>> chan->conn->sent++;
> >>> }
> >>> +
> >>> + if (resched && cnt != tmp)
> >>> + break;
> >>> }
> >>>
> >>> if (hdev->le_pkts)
> >>> @@ -4444,24 +4488,33 @@ static void hci_sched_le(struct hci_dev *hdev)
> >>> else
> >>> hdev->acl_cnt = cnt;
> >>>
> >>> - if (cnt != tmp)
> >>> + if (cnt == 0 && cnt != tmp)
> >>> hci_prio_recalculate(hdev, LE_LINK);
> >>> +
> >>> + return resched;
> >>> }
> >>>
> >>> static void hci_tx_work(struct work_struct *work)
> >>> {
> >>> struct hci_dev *hdev = container_of(work, struct hci_dev, tx_work);
> >>> struct sk_buff *skb;
> >>> + bool resched;
> >>>
> >>> BT_DBG("%s acl %d sco %d le %d", hdev->name, hdev->acl_cnt,
> >>> hdev->sco_cnt, hdev->le_cnt);
> >>>
> >>> if (!hci_dev_test_flag(hdev, HCI_USER_CHANNEL)) {
> >>> /* Schedule queues and send stuff to HCI driver */
> >>> - hci_sched_acl(hdev);
> >>> - hci_sched_sco(hdev);
> >>> - hci_sched_esco(hdev);
> >>> - hci_sched_le(hdev);
> >>> + do {
> >>> + /* SCO and eSCO send all packets until emptied */
> >>> + hci_sched_sco(hdev);
> >>> + hci_sched_esco(hdev);
> >>> +
> >>> + /* Acl and Le send based on quota (priority on ACL per
> >>> + * loop)
> >>> + */
> >>> + resched = hci_sched_acl(hdev) || hci_sched_le(hdev);
> >>> + } while (resched);
> >>> }
> >>
> >> I am not in favor of this busy loop. We might want to re-think the whole scheduling by connection type and really only focus on scheduling ACL (BR/EDR and LE) and audio packets (SCO/eSCO and ISO).
> >
> > I think the busy loop is the simplest solution if we want to solve the
> > problem: don't send 2 ACL packets without checking if there is a SCO
> > packet scheduled (which is the worst case I'm worried about on UART
> > interfaces).
> >
> > If we get rid of the connection type scheduling and only do audio and
> > ACL, we would still need some mechanism to guarantee that you don't
> > send >~1100 bytes without checking if SCO is queued (assuming 3000000
> > baudrate and 3.75ms latency requirement).
>
> Why don’t we just say that if SCO is queued up, then after each ACL packet we should send a SCO packet.
That sounds good. Effectively, this is what I wanted to achieve
without modifying the ACL round robin mechanism too much.
>
> >
> >>
> >> In addition, we also need to check that SCO scheduling and A2DP media channel ACL packets do work together. I think that generally it would be best to have a clear rate at which SCO packets are require to pushed down to the hardware. So you really reserve bandwidth and not blindly prioritize them via a busy loop.
> >>
> > I am less worried about bandwidth and more about latency. If I start
> > sending really large ACL packets through UART, it could take multiple
> > milliseconds. It really has to be reserved bandwidth per small
> > timeslice (like 3.75ms) so I can guarantee that if a SCO packet is
> > seen within that time slice, it will be transferred. There will still
> > have to be a busy loop though because the amount of data you can send
> > in the time slice will probably be less than the data that can be
> > in-flight to the controller (i.e. acl_max_pkts).
>
> Right now we kinda let the SCO socket application provide the correct timing. I was thinking that the kernel might need to enforce this.
I was under the assumption that the Num Completed Pkts event would
actually help us regulate the timing (assuming controller sends that
event once it actually sends SCO packet over the air). Currently, we
don't seem to be using it for SCO.
>
> Regards
>
> Marcel
>
For the next patch revision, I will remove the driver specific enable,
gotos and scheduling of acl block. I'll also add a limit to SCO
packets sent so it observes and respects the number of sco packets
completed (same as ACL).
I'm not yet comfortable refactoring the scheduling from per connection
to per type, especially as I'm not sure what to do with ISO or ACL
audio. I think those will require a bit more thought.
Thanks
Abhishek
Hi Abhishek,
>>>>> When scheduling TX packets, send all SCO/eSCO packets first and then
>>>>> send only 1 ACL/LE packet in a loop while checking that there are no SCO
>>>>> packets pending. This is done to make sure that we can meet SCO
>>>>> deadlines on slow interfaces like UART. If we were to queue up multiple
>>>>> ACL packets without checking for a SCO packet, we might miss the SCO
>>>>> timing. For example:
>>>>>
>>>>> The time it takes to send a maximum size ACL packet (1024 bytes):
>>>>> t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
>>>>> where 10/8 is uart overhead due to start/stop bits per byte
>>>>>
>>>>> Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666
>>>>> and is pretty close to a common baudrate of 3000000 used for BT. At this
>>>>> baudrate, if we sent two 1024 byte ACL packets, we would miss the 3.75ms
>>>>> timing window.
>>>>>
>>>>> Signed-off-by: Abhishek Pandit-Subedi <[email protected]>
>>>>> ---
>>>>>
>>>>> include/net/bluetooth/hci_core.h | 1 +
>>>>> net/bluetooth/hci_core.c | 91 +++++++++++++++++++++++++-------
>>>>> 2 files changed, 73 insertions(+), 19 deletions(-)
>>>>>
>>>>> diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
>>>>> index d4e28773d378..f636c89f1fe1 100644
>>>>> --- a/include/net/bluetooth/hci_core.h
>>>>> +++ b/include/net/bluetooth/hci_core.h
>>>>> @@ -315,6 +315,7 @@ struct hci_dev {
>>>>> __u8 ssp_debug_mode;
>>>>> __u8 hw_error_code;
>>>>> __u32 clock;
>>>>> + __u8 sched_limit;
>>>>
>>>> why do you need this parameter?
>>>
>>> This is really only necessary on systems where the data transfer rate
>>> to the controller is low. I want the driver to set whether we should
>>> aggressively schedule SCO packets. A quirk might actually be better
>>> than a variable (wasn't sure what is preferable).
>>
>> or maybe we try without driver choice first. I would assume what is required for UART, will not harm USB or SDIO transports either.
>
> Ack -- I can make this default behavior.
>
>>
>>>>> __u16 devid_source;
>>>>> __u16 devid_vendor;
>>>>> diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
>>>>> index dbd2ad3a26ed..00a72265cd96 100644
>>>>> --- a/net/bluetooth/hci_core.c
>>>>> +++ b/net/bluetooth/hci_core.c
>>>>> @@ -4239,18 +4239,32 @@ static void __check_timeout(struct hci_dev *hdev, unsigned int cnt)
>>>>> }
>>>>> }
>>>>>
>>>>> -static void hci_sched_acl_pkt(struct hci_dev *hdev)
>>>>> +/* Limit packets in flight when SCO/eSCO links are active. */
>>>>> +static bool hci_sched_limit(struct hci_dev *hdev)
>>>>> +{
>>>>> + return hdev->sched_limit && hci_conn_num(hdev, SCO_LINK);
>>>>> +}
>>>>> +
>>>>> +static bool hci_sched_acl_pkt(struct hci_dev *hdev)
>>>>> {
>>>>> unsigned int cnt = hdev->acl_cnt;
>>>>> struct hci_chan *chan;
>>>>> struct sk_buff *skb;
>>>>> int quote;
>>>>> + bool sched_limit = hci_sched_limit(hdev);
>>>>> + bool resched = false;
>>>>>
>>>>> __check_timeout(hdev, cnt);
>>>>>
>>>>> while (hdev->acl_cnt &&
>>>>> (chan = hci_chan_sent(hdev, ACL_LINK, "e))) {
>>>>> u32 priority = (skb_peek(&chan->data_q))->priority;
>>>>> +
>>>>> + if (sched_limit && quote > 0) {
>>>>> + resched = true;
>>>>> + quote = 1;
>>>>> + }
>>>>> +
>>>>> while (quote-- && (skb = skb_peek(&chan->data_q))) {
>>>>> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
>>>>> skb->len, skb->priority);
>>>>> @@ -4271,19 +4285,26 @@ static void hci_sched_acl_pkt(struct hci_dev *hdev)
>>>>> chan->sent++;
>>>>> chan->conn->sent++;
>>>>> }
>>>>> +
>>>>> + if (resched && cnt != hdev->acl_cnt)
>>>>> + break;
>>>>> }
>>>>>
>>>>> - if (cnt != hdev->acl_cnt)
>>>>> + if (hdev->acl_cnt == 0 && cnt != hdev->acl_cnt)
>>>>> hci_prio_recalculate(hdev, ACL_LINK);
>>>>> +
>>>>> + return resched;
>>>>> }
>>>>>
>>>>> -static void hci_sched_acl_blk(struct hci_dev *hdev)
>>>>> +static bool hci_sched_acl_blk(struct hci_dev *hdev)
>>>>> {
>>>>> unsigned int cnt = hdev->block_cnt;
>>>>> struct hci_chan *chan;
>>>>> struct sk_buff *skb;
>>>>> int quote;
>>>>> u8 type;
>>>>> + bool sched_limit = hci_sched_limit(hdev);
>>>>> + bool resched = false;
>>>>>
>>>>> __check_timeout(hdev, cnt);
>>>>>
>>>>> @@ -4297,6 +4318,12 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>>>>> while (hdev->block_cnt > 0 &&
>>>>> (chan = hci_chan_sent(hdev, type, "e))) {
>>>>> u32 priority = (skb_peek(&chan->data_q))->priority;
>>>>> +
>>>>> + if (sched_limit && quote > 0) {
>>>>> + resched = true;
>>>>> + quote = 1;
>>>>> + }
>>>>> +
>>>>> while (quote > 0 && (skb = skb_peek(&chan->data_q))) {
>>>>> int blocks;
>>>>>
>>>>> @@ -4311,7 +4338,7 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>>>>>
>>>>> blocks = __get_blocks(hdev, skb);
>>>>> if (blocks > hdev->block_cnt)
>>>>> - return;
>>>>> + return false;
>>>>>
>>>>> hci_conn_enter_active_mode(chan->conn,
>>>>> bt_cb(skb)->force_active);
>>>>> @@ -4325,33 +4352,39 @@ static void hci_sched_acl_blk(struct hci_dev *hdev)
>>>>> chan->sent += blocks;
>>>>> chan->conn->sent += blocks;
>>>>> }
>>>>> +
>>>>> + if (resched && cnt != hdev->block_cnt)
>>>>> + break;
>>>>> }
>>>>>
>>>>> - if (cnt != hdev->block_cnt)
>>>>> + if (hdev->block_cnt == 0 && cnt != hdev->block_cnt)
>>>>> hci_prio_recalculate(hdev, type);
>>>>> +
>>>>> + return resched;
>>>>> }
>>>>>
>>>>> -static void hci_sched_acl(struct hci_dev *hdev)
>>>>> +static bool hci_sched_acl(struct hci_dev *hdev)
>>>>> {
>>>>> BT_DBG("%s", hdev->name);
>>>>>
>>>>> /* No ACL link over BR/EDR controller */
>>>>> if (!hci_conn_num(hdev, ACL_LINK) && hdev->dev_type == HCI_PRIMARY)
>>>>> - return;
>>>>> + goto done;
>>>>
>>>> Style wise the goto done is overkill. Just return false.
>>>
>>> Will do.
>>>
>>>>
>>>>>
>>>>> /* No AMP link over AMP controller */
>>>>> if (!hci_conn_num(hdev, AMP_LINK) && hdev->dev_type == HCI_AMP)
>>>>> - return;
>>>>> + goto done;
>>>>>
>>>>> switch (hdev->flow_ctl_mode) {
>>>>> case HCI_FLOW_CTL_MODE_PACKET_BASED:
>>>>> - hci_sched_acl_pkt(hdev);
>>>>> - break;
>>>>> + return hci_sched_acl_pkt(hdev);
>>>>>
>>>>> case HCI_FLOW_CTL_MODE_BLOCK_BASED:
>>>>> - hci_sched_acl_blk(hdev);
>>>>> - break;
>>>>> + return hci_sched_acl_blk(hdev);
>>>>
>>>> So the block based mode is for AMP controllers and not used on BR/EDR controllers. Since AMP controllers only transport ACL packet and no SCO/eSCO packets, we can ignore this here.
>>>
>>> Ok, I'll remove it there.
>>>
>>>>
>>>>> }
>>>>> +
>>>>> +done:
>>>>> + return false;
>>>>> }
>>>>>
>>>>> /* Schedule SCO */
>>>>> @@ -4402,16 +4435,18 @@ static void hci_sched_esco(struct hci_dev *hdev)
>>>>> }
>>>>> }
>>>>>
>>>>> -static void hci_sched_le(struct hci_dev *hdev)
>>>>> +static bool hci_sched_le(struct hci_dev *hdev)
>>>>> {
>>>>> struct hci_chan *chan;
>>>>> struct sk_buff *skb;
>>>>> int quote, cnt, tmp;
>>>>> + bool sched_limit = hci_sched_limit(hdev);
>>>>> + bool resched = false;
>>>>>
>>>>> BT_DBG("%s", hdev->name);
>>>>>
>>>>> if (!hci_conn_num(hdev, LE_LINK))
>>>>> - return;
>>>>> + return resched;
>>>>>
>>>>> cnt = hdev->le_pkts ? hdev->le_cnt : hdev->acl_cnt;
>>>>>
>>>>> @@ -4420,6 +4455,12 @@ static void hci_sched_le(struct hci_dev *hdev)
>>>>> tmp = cnt;
>>>>> while (cnt && (chan = hci_chan_sent(hdev, LE_LINK, "e))) {
>>>>> u32 priority = (skb_peek(&chan->data_q))->priority;
>>>>> +
>>>>> + if (sched_limit && quote > 0) {
>>>>> + resched = true;
>>>>> + quote = 1;
>>>>> + }
>>>>> +
>>>>> while (quote-- && (skb = skb_peek(&chan->data_q))) {
>>>>> BT_DBG("chan %p skb %p len %d priority %u", chan, skb,
>>>>> skb->len, skb->priority);
>>>>> @@ -4437,6 +4478,9 @@ static void hci_sched_le(struct hci_dev *hdev)
>>>>> chan->sent++;
>>>>> chan->conn->sent++;
>>>>> }
>>>>> +
>>>>> + if (resched && cnt != tmp)
>>>>> + break;
>>>>> }
>>>>>
>>>>> if (hdev->le_pkts)
>>>>> @@ -4444,24 +4488,33 @@ static void hci_sched_le(struct hci_dev *hdev)
>>>>> else
>>>>> hdev->acl_cnt = cnt;
>>>>>
>>>>> - if (cnt != tmp)
>>>>> + if (cnt == 0 && cnt != tmp)
>>>>> hci_prio_recalculate(hdev, LE_LINK);
>>>>> +
>>>>> + return resched;
>>>>> }
>>>>>
>>>>> static void hci_tx_work(struct work_struct *work)
>>>>> {
>>>>> struct hci_dev *hdev = container_of(work, struct hci_dev, tx_work);
>>>>> struct sk_buff *skb;
>>>>> + bool resched;
>>>>>
>>>>> BT_DBG("%s acl %d sco %d le %d", hdev->name, hdev->acl_cnt,
>>>>> hdev->sco_cnt, hdev->le_cnt);
>>>>>
>>>>> if (!hci_dev_test_flag(hdev, HCI_USER_CHANNEL)) {
>>>>> /* Schedule queues and send stuff to HCI driver */
>>>>> - hci_sched_acl(hdev);
>>>>> - hci_sched_sco(hdev);
>>>>> - hci_sched_esco(hdev);
>>>>> - hci_sched_le(hdev);
>>>>> + do {
>>>>> + /* SCO and eSCO send all packets until emptied */
>>>>> + hci_sched_sco(hdev);
>>>>> + hci_sched_esco(hdev);
>>>>> +
>>>>> + /* Acl and Le send based on quota (priority on ACL per
>>>>> + * loop)
>>>>> + */
>>>>> + resched = hci_sched_acl(hdev) || hci_sched_le(hdev);
>>>>> + } while (resched);
>>>>> }
>>>>
>>>> I am not in favor of this busy loop. We might want to re-think the whole scheduling by connection type and really only focus on scheduling ACL (BR/EDR and LE) and audio packets (SCO/eSCO and ISO).
>>>
>>> I think the busy loop is the simplest solution if we want to solve the
>>> problem: don't send 2 ACL packets without checking if there is a SCO
>>> packet scheduled (which is the worst case I'm worried about on UART
>>> interfaces).
>>>
>>> If we get rid of the connection type scheduling and only do audio and
>>> ACL, we would still need some mechanism to guarantee that you don't
>>> send >~1100 bytes without checking if SCO is queued (assuming 3000000
>>> baudrate and 3.75ms latency requirement).
>>
>> Why don’t we just say that if SCO is queued up, then after each ACL packet we should send a SCO packet.
>
> That sounds good. Effectively, this is what I wanted to achieve
> without modifying the ACL round robin mechanism too much.
Lets try this first and see how it goes. We might need to do some modifications, but it is worth a try.
>>>> In addition, we also need to check that SCO scheduling and A2DP media channel ACL packets do work together. I think that generally it would be best to have a clear rate at which SCO packets are require to pushed down to the hardware. So you really reserve bandwidth and not blindly prioritize them via a busy loop.
>>>>
>>> I am less worried about bandwidth and more about latency. If I start
>>> sending really large ACL packets through UART, it could take multiple
>>> milliseconds. It really has to be reserved bandwidth per small
>>> timeslice (like 3.75ms) so I can guarantee that if a SCO packet is
>>> seen within that time slice, it will be transferred. There will still
>>> have to be a busy loop though because the amount of data you can send
>>> in the time slice will probably be less than the data that can be
>>> in-flight to the controller (i.e. acl_max_pkts).
>>
>> Right now we kinda let the SCO socket application provide the correct timing. I was thinking that the kernel might need to enforce this.
>
> I was under the assumption that the Num Completed Pkts event would
> actually help us regulate the timing (assuming controller sends that
> event once it actually sends SCO packet over the air). Currently, we
> don't seem to be using it for SCO.
That is a good question and I don’t have an answer on the top of my head. We would have to check the spec text and see if controllers really follow it.
> For the next patch revision, I will remove the driver specific enable,
> gotos and scheduling of acl block. I'll also add a limit to SCO
> packets sent so it observes and respects the number of sco packets
> completed (same as ACL).
>
> I'm not yet comfortable refactoring the scheduling from per connection
> to per type, especially as I'm not sure what to do with ISO or ACL
> audio. I think those will require a bit more thought.
From a packet perspective, we have ACL and SCO/eSCO packets and ISO will be another type. That is just how it is defined in the spec. However we are putting everything into data_q and I wonder if we should just add priority handling to the SCO/eSCO scheduling. We have done this for ACL so that high priority L2CAP connections come first. We would just need a way to say SCO/eSCO comes first.
Regards
Marcel